SPECIAL REPAIRS TO BLDG NO. T-16 OF SATA REGT AT NLP MIL STN UNDER GE 872 EWS

Amount

B/R SERVICES/ WORKS

Demolition Cement Concrete (Un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) of any description, not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) of any description, exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Taking down Shutter of any description, exc. 1.00 Square Metre but not exc. 2.00 Square Metre Each, complete all as specified and as directed.

Dismantling Wrought Iron or Mild Steel Work of any description, complete all as specified and as directed.

Dismantling Asbestos Cement (Corrugated or Semi-corrugated) Sheets in Roof Coverings, etc. of any thickness including Nainital or Similar Pattern Roof Coverings, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Ceiling Frame (Snap Grid) with Hangers of any descriptions but except Wall and Ceiling Boards, complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and Removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including Raking out Joints, Hacking for Key, Scrubbing down with Water and Removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Slabs supported on Walls, Beams and Columns in Floors of Water Tanks, Roofs, Landings, Balconies, Canopies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Landings, Cover Slabs (for Manholes, etc.), Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and Similar Articles with Plain faces and Setting in Cement Morter 1:4, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appro-priate Items.

M&L Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and Similar Works; not exc. 200mm thick (Horizontal or Sloping), etc., Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work Half Brick thick with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan to any Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cutting Holes in Brick Walls, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to Dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) and Adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cutting Chases, Pinning in, Making Good to facings where required and Pointing in Cement Mortar 1:3 to Ends or Edges of Cills, Shelves, Lintels, etc., and Cutting Chases for Concealed Water Tubing and Making Good, Cutting Girth exc. 10 Cm but not exc. 20 Cm, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

S&F Flush Shutter 35mm thick, Solid Core Construction, with Block Board Core and Plywood Face Panels, Commercial type on Both Sides including Teakwood Lipping 6.0mm thick, fixed with Nails, complete all as specified and as directed.

Taking down Shutter of any description, exc. 1.00 Square Metre but not exc. 2.00 Square Metre Each and Re-fixing in the Same Opening including Cutting to Size and Fitting, complete all as specified and as directed.

S&F Fiber Glass Reinforced Plastic (FRP) Door Frame of Cross sSection 90x45mm having Single Rebate of 32x15mm to receive 30mm thick Shutter. The Laminte shall be moulded with Fire Resistant grade Unsaturated Polyester Resin and Chopped Mat and Door Frame Laminate shall be 2.0mm thick and shall be filled with suitable Wooden Block in all the 3 Legs. The Frame shall be covered with Fiber Glass from all Sides. Mild Steel Stay shall be provided at the Bottom to steady the Frame all as specified by the Manufacturer, complete all as specified and as directed.

S&F Glass Fibre Reinforced Plastic (FRP) Panelled Door Shutter 30mm thick of required Colour and Approved Brand and Manufacture, made with Fire Retardant grade Unsaturated Polyester Resin, moulded to 3.0mm thick FRP Laminate for forming Hollow Rails and Styles with Wooden Frame and suitable Blocks of Seasoned Wood inside at required Places for fixing of Fittings, Cast Monolithi-cally with 5.0mm thick FRP Laminate for Panels conforming to IS:14856 including Fixing to existing Door Frames, complete all as specified by the Manufacturer, complete all as specified and as directed.

M&L Anodised Aluminium Powder Coated (Thickness of Powder Coating not less than 50 micron) Frame for Doors, Windows, Ventilators with One or More Rebates including Joining Cleat for fixing, etc., complete all as specified and as directed.

M&L Anodised Aluminium Powder Coated (Thickness of Powder Coating not less than 50 micron) Sliding 3 Track Window, 3 Shutter Series B (SHUTTER SECTION - 18mm) with Two Glazed Shutters Each Covering One Third Opening and One Gauged Shutter Covering, One Third Opening including Self Closing Locking Arrangement, Stoppers and Rubber Beading Gasket Without Sash Bars, Auminum Section Weighing 1.06 Kg/RM including necessary Jointing Cleats, Glazing Clips, Rubber Packing, Powder Coated Aluminum Beading, Screws, etc. including Anodised Aluminium Fittings in Each Shutter with and including 5.0mm thick Tinted Glass, Stainless Steel Wire Cloth of 0.36mm dia and avg Width of Aperture 1.40mm, complete all as specified and as directed. NOTE : 3-way Track Sliding Window Frame of Size 92x31.75x1.5mm and Shutter Size 40x18mm with 9.0mm Interlocking Leg x 1.45mm thick and Weight not less than 0.607 Kg/RM.

M&L Anodised Aluminium Powder Coated (Thickness of Powder Coating not less than 50 micron) Ventilator, Openable, Top Hung and Bottom Portion Fixed type Without Sash Bars with Aluminium Section Weighing 0.55 Kg/RM including Glazing, necessary Joining Cleats, Glazing Clips, Rubber Packing, Anodised Aluminium Snap Beading, Screws and Top Hung Shutter Fixed Hook & Eye with Minimum 01 No. on Each Shutter, 01 No. Aluminium Tower Bolt 100mm Long and Aluminium Handle 75mm Long in Each Shutter, etc., complete all as specified and as directed. NOTE : Glazing, Wire Mesh shall be Measured and Paid separately against respective Items.

S&F Aluminium anodised Barrel Tower Bolt (as approved) of Size 150mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt (as approved) of Size 200mm long, Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 250mm long (as approved) with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium Alloy and Fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge (as approved) of Size 75mm, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge (as approved) of Size 100mm, complete all as specified and as directed.

S&F Anodised Aluminium Handle (as approved) of Size 150mm, Cast type, complete all as specified and as directed.

S&F Floor Door Stopper having Overall length of Cover Plate 75mm of Aluminium Alloy Body and Tongue, anodised, with Hard Drawn Steel Spring, fixing in Floor and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Curtain Rail/ Rod 24/25mm Outer Dia with and including Stainless Steel Decorative Finials with Stainless Steel Brackets and fixed on Walls, etc. and Fixed-in-repairs, complete all as specified and as directed. NOTE :- (a) Stainless Steel Decorative Finials and Stainless Steel Brackets shall be provided for Each Length of Curtain Rail/ Rod and Cost of the same will deemed to be inciuded in the Quoted Unit Rate. (b) Only Length of Stainless Steel Curtain Rail/ Rod will be Measured for Payment.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixing with Stainless Steel Wire Staples and Fixed-in-repairs, complete all as specified and as directed.

S&F Sheet Glass 4.0mm thick, Figured or Pin Headed and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, Cut to length, Bent to Shape required including Cranking, Bending Spirally for Hooping for Columns, hooking Ends and Binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts; Wall Ties and similar small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Mild Steel Framed Works such as Grills, Gratings, etc. with Ends of Bars shouldered and/or riveted or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walkways; Railings; Framework of Water Tanks and similar Work, conforming to Fe-290, Gde-E-165, complete all as specified and as directed.

M&L Framed Brackets of Angles or Tees with Web and Flanges, cut to Shape, drilled and countersunk for Screw including bending and welding Angles as necessary, Gusset Plates, Riveting, etc., not exc. 10 KG Each Brackets, conforming to Fe-290, Gde E-165, complete all as specified and as directed.

M&L Mild Steel Tublar Trusses, Rafter, Purlins, etc. including Special Shaped Washers, etc. complete using ERW or Induction Butt welded Tubes, confirming to IS:1161-1979, Grade St-240, complete all as specified and as directed.

M&L Plates (Plain or Chequered) Channels, Square cut or Notched (Ordinary and Counter Sunk) forming Holes, without any Aattachment, conform to Gde Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Mild Steel Screw Bolts (Machine made) of any description (Lengths and Diameter of Bolts as required at Site of Work/ as directed) with Hexagonal or Square Heads at One End and screwed the Other End, or screwed Both Ends, Each screwed End to be fitted with Washers and One Hexagonal or Square Nut, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Aluminum Anodised Snap Grid/ Frame Work of Size 605x605mm in Ceiling, all as per Specification and Drawing of MES Schedule (except Hangers), complete all as specified and as directed.

S&F Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in Size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F Fibre Insulation Boards 12mm thick, Ordinary type and fixed or laid/ inserted to Aluminum Snap Grid Frame Work with Screws, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 40mm thick in Flooring, etc., laid in Alternate Panels, finished Concrete Surfaces Even and Smooth with using Extra Cement, complete all as specified and as directed.

M&L Glass Dividing Strips 38mm Wide and 3.0mm thick and inserted in Position, conform to Design, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles (1st quality and as approved) 7.0mm to 8.0mm thick, Joint Free (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed will deemed to be included in Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 600x300x7.0mm thick (1st quality and/or as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed NOTE : Cost of Screed Bed will deemed to be included in Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick in Pavings, Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without using Extra Cement, complete all as specified and as directed.

M&L Bitumastic Filling comprising 1 Part of Bitumen of Grade 85/25 and 3 Parts of Sand by Weight, complete all as specified and as directed.

M&L Rendering 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 15mm thick on Bricks/Pre-cast Blocks or Concrete Works consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/Top layer, finished Fair and Even, complete all as specified and as directed NOTE : Water Proofing Compound (WPC) will be Measured and Paid sepa-rately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls and applying Two Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Wall Care Putty 3.0mm thick in Two Coats (1.5mm thick in Each Coat) on Plastered Surfaces of Walls including Cutting and Rubbing down to obtain an Even and Smooth Surface, complete all as specified and as directed.

M&L Preparing Old Plastered Surfaces of Walls by Complete Removing Existing Surface Treatment and applying Wall Care Putty 1.5mm thick including Cutting and Rubbing down to obtain an Even and Smooth Surface, complete all as specified and as directed.

M&L Applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Chalk Whitening (Priming Coat) on Putty Finished Surfaces, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Plastered Surfaces of Walls by Complete Removing Existing Surface Treatment and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, exc. 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Treated Steel and Iron Surfaces of any descriptions, exc. 10 Cm in Width or Girth and Applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Previously Untreated Surfaces of Wood and Wood Based Materials, of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Backs of Chowkats, etc. Area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing Previously Untreated Surfaces of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items, Area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors including Taking up or down Old Unserviceable Pipes/ Steel Tubing and Connections, complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors including Taking up or down Old Unserviceable Pipes/ Steel Tubing and Connections, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, Fancy type, with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Fixed-in-repairs, complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy with Capstan Heads, Chromium Plated, Fancy type, Quarter Turn (Form Flow), screwed down, high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

S&F Stop Valve/ Angle Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule and Providing GI Tank Nipple 20mm bore (dia) and Water Connections including Lowering down Unserviceable Water Storage Tank of any description after disconnecting of Water Connections, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm bore (dia), having weight not less than 210 Gram, high pressure with Epoxy Coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe including Taking down Old Unserviceable Ball Valve of any description, complete all as specified and as directed.

M&L Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with Trap and Fixing Bolts and Making Good to Floor/Distrubed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), White, Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminium anodised Hinging Device and Fixed-in-repairs, complete all as specified and as directed.

S&F Brass Chromium Plated Jet Spray (as approved) with Connection Pipe 15mm bore (dia) and suitable for Wash Down Water Closet Pan (Pedestal Pattern) and Fixed-in-repairs, complete all as specified and as directed.

S&F Toitet Paper Holder of Size 150mm (as approved), Brass Chromoum Plated with Rod to hold Paper Roll and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float & Handle, and PVC Flush Pipe 32mm bore (dia) for suitable Length, a Pair of Cast Iron Brackets Erecting Stand duly Painted including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin 550x400mm in Size, Flat Back including Brass Chromium Plated Waste Coupling/ Fitting 32mm bore (dia) of 300mm Long and PVC Waste Pipe 32mm bore (dia) including a Pair of Cast Iron Brackets Brackets Erecting Stand duly Painted, Cutting and Pinning in Ends and Fixed including Making Good disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed.

S&F Brass Chromium Plated Waste Coupling/ Fitting 32mm bore (dia) of 300mm Long suitable for Glazed Wash Hand Basins with Long screwed Shanks and Fly-nuts, Flange End bedded in Red Lead Cement and Fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China White Urinal of Size 330x330x320mm or nearest Size as approved, Half Stall type, (excluding Flushing Cistern, Flush Pipe and Waste Pipe), complete including Providing and fixing Plugs, Bedding Urinals against Wall in Cement Mortar 1:2, securing Urinal to Plug with and including 60mm long Brass Chromium plated Screws, Pointing around Urinal back in Cement Mortar 1:3, fixing Urinal Spreder of Brass Chromium plated, Flush Pipe, Grating and Union for Discharge Pipe (but Exclusive of fixing Supply Pipe to Flushing Cistern, Trap and Waste Pipe) and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Waste Pipes 32/40mm bore (dia) suitable for Wash Hand Basin, Sinks, Urinals, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in Size and 450mm in length with PTMT Nuts suitable for connecting with Flushing Cistern, Wash Hand Basin, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair) and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Soap Dish, not less than 125mm in size (as approved), fixing to Walls with and including Chromium plated Brass Screws and Wooden/ Plastic Cleats and Fixing-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) Floor Trap having Diameter of Outlet 75mm, Plain with Grating including Jointing with Solvent Cement and Fixing-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) Pipe 110mm bore (dia), Single Socketed, in any length with Rubber Ring Joints, laid on Floors or fixing to Walls with and including Mild Steel Flat Iron (25x3.0mm) Clamps and Mild Steel Bolts, Nuts, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any Radius, etc. and Jointing with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl 110mm bore (dia) and Jointing with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed.

M&L Cutting into Existing Manholes for Connecting New Drain Pipes of 150/160mm (Internal dia), Making Good to Pipe and Rendering, Cutting out Existing Benching for and Forming Branch Channel (½ Round or ¾ Section) in Cement Concrete 1:2:4 (20mm graded stone aggregate), Smooth Finished and Reforming Benching as required, complete all as specified and as directed.

E/M SERVICES/ WORKS

M&L Taking down carefully Copper Point Wiring (Light, Fan, Socket or Power) complete from in any Position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets but excluding Light Fittings of any description, Making Good Disturbed Surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down Unserviceable Sub-main Wiring from PVC Conduit/ PVC Casing Capping of any description, Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/ Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN/ BELL POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated unsheathed multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated unsheathed multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 1.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable with 2.5 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable Size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 6.0 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable and 1-Run of 6.0 Sqmm (nominal area) FRLSH 1100 Volt grade PVC insulated, unsheathed, multi-stranded, single core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn through and including PVC Casing Capping (ISI Marked) of suitable Size (approx 25/32mm width) along with all Fitting/Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Runs of Cables & 1-Run of PVC Casing Capping will deem to include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT. (b) Sub-main Wiring will be measured PVC Casing Capping only for Payment. Wires required for Looping, etc. as ordered will deem to include in the Quoted Unit Rate.

S&F PVC Rectangular Board/Block of Size 175x100x50mm Deep, Closed Recessed with 3.0mm thick Plastic Laminated Sheet Cover for mounting Swiches, Sockets, Fan Regulators, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6/16 Amp, 3 Pin, 2-in-1, Multi-plug, Flush type, 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Lamp/ Angle Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and Connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and Connecting up, complete all as specified and as directed.

S&F Ceiling Fan Regulator, Dimmar Switch type, 230 Volt AC, Rotary Stepped, Electronic type 120/280 Volt and connecting up, complete all as specified and as directed.

S&F Decorative LED Light Fitting 1x10 Watt Bulkhead Luminaires including LED Light, Driver, Holder, Connecting up with and including of suitable Size and Length Flexible Copper Conductor Cable, 3 Core and Fixed-in-repairs, complete all as specified and as directed.

S&F Decorative LED Batten Ultra Slim Round Profile Lighting Fixture 1x20 Watt with Extruded Polycarbonate, Connecting up with and including of suitable Size and Length Flexible Copper Conductor Cable, 3 Core from Ceiling Rose to Light Fitting and Fixed-in-repairs, complete all as specified and as directed.

M&L Taking/ Lowering down Ceiling Fan of any Make/Model/Sweep from any Height after disConnecting Electric Connection and Keep in Safe Custody for Re-hanging/ Re-fixing and Repairing, complete all as specified and as directed.

M&L Opening Ceiling Fan body in presence of JE-in-Charge, Checking for Repair Works involving, Transporting Ceiling Fan 1200/1400mm Sweep from AGE E/M Store Yard at NLP to nearest Workshop, Taking out carefully burnt out Winding of any type from the Fan of any Make, Cleaning of Slots, Rewinding Fan Motor with Super Enamalled Copper Wiinding Wire of suitable Gauge and Weight (not less than 350 Gram) providing New Insulation Materials, Varnishing, Heating, Reassembling & Testing for Smooth Functioning after Rewinding, Removing the Fan to Site of Work after Rewinding, complete all as specified and as directed.

M&L Preparing Old Painted Surfaces of Fan including Cleaning, Washing, Rubbing and Filling Cavities with Filler, applying One Coat of Synthetic Enamel Paint (as approved) with Spray Painting Machine and Writing MES No. with Black Paint, complete all as specified and as directed.

M&L Mild Steel Flat Iron 40x5mm in Fan Hooks, Cut to Length, bent to Shape as ordered, drilling holes for Bolts including providing Mild Steel Bolts, Nuts and Washers, conforming to Fe-290 Gde-E-165 and Fixed-in-repairs, complete all as specified and as as directed.

M&L Re-hanging/ Re-fixing only Ceiling Fan (obtained from BOQ Item No. 2.17 here-in-before) after repaired and Connecting up with and including 3 Core Flexible Copper Conductor Cable of suitable Size and Length from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

S&F Exhaust Fan 380mm Sweep, Steel body complete with Frame and Louvers, 230 Volt, 50 Hz, 1200 RPM, Copper Winding with Fixing Arrangement using Fastener, Connecting up with and including of suitable Size and Length Flexible Copper Conductor Cable, 3 Core including Taking/ Lowering down Old Unserviceable Exhaust Fan of any description after disconnecting and Removing to AGE E/M Store Yard at NLP and deposited, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt, Connecting up and Fixed-in-repairs, complete all as specified and as asdirected.

S&F MCB Single Pole & Neutral 10 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt, Connecting up and Fixed-in-repairs, complete all as specified and as as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 4-Way, SPN, 240 Volt, Double Doors, Epoxy Based Powder Coated Painted, suitable for mounting MCB DP/SPN as Incomer and MCB SP as Out-going with 200 Amp rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up including Taking down/ out Unserviceable MCB DBs of any description, complete all as specified and as directed.

S&F Sheet Metal Enclosure for DB's when MCBs to be used 8-Way, SPN, 240 Volt, Double Doors, Epoxy Based Powder Coated Painted, suitable for mounting MCB DP/SPN as Incomer and MCB SP as Out-going with 200 Amp rated Bus-bar, Neutral Bar, Earth Bar, Connecting Cable Links and Connecting up including Taking down/ out Unserviceable MCB DBs of any description, complete all as specified and as directed.

Excavating in Trenches, not exc. 1.50 Metre Wide and not exc. 1.50 Metre in Depth for Laying of Electrical Cable Lines, Water Pipe Lines, etc., Forming Surfaces to required Foundation/ Gradient and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Providing Heaps with Surplus Soil along the Route of the Electrical Cable Lines, Water Pipe Lines, etc. in Soft/Loose soil, complete all as specified and as directed.

Disconnecting & Taking down/out Unserviceable LT Cable of any Size and any description including GI Pipes, Bricks, etc. from Trenches, Floors, Poles, Walls, complete all as specified and as directed. NOTE : Necessary Earthworks will be Measured & Paid under appropriate Items.

Taking up or down Steel Tubing 25mm bore (dia) and Connections/ Fittings of any description, complete all as specified and as directed. NOTE : Necessary Earthworks will be Measured & Paid under appropriate Items.

Taking up or down Steel Tubing 32mm bore (dia) and Connections/ Fittings of any description, complete all as specified and as directed. NOTE : Necessary Earthworks will be Measured & Paid under appropriate Items.

M&L XLPE insulated, armoured heavy duty, Electric Cable with Aluminium Conductor, 1100 Volt grade, Cross-sectional Area 25 Sqmm, 3½ Core, laid in Trenches / Ducts or Passing through Pipes or Fixing on Poles, etc., complete all as specified and as directed. NOTE : Necessary Earth works, Sand cushioning, Cable Protection Cover & GI Pipe, etc. will be Measured and Paid separately under relevent Items.

M&L Sand Cushioning (dry) in Trenches/Ducts for protection of UG Cables (below, above and around the UG Cable laid) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 Cm in depth after laying the Cable) and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE : For the purpose of Payment, Punned thickness of Sand Cushioning only will be Measured.

Supply & laying Sub-class ‘B’ Bricks of Size 230x115x75mm, Kiln burnt, for Covering to UG Cable as Protection, laid Flat, Transversally Width Equal to the Length of the Cable, complete all as specified and as directed.

Supply, Installation & Commissioning Factory Made LT Feeder Pillar Box (CPRI Approved/ Tested Manufacturer) made out of 3.15mm thick CRCA Sheet, Outdoor type, suitable for 415 Volt, 3 Phase, 4-Wire System, 50 Hz Supply, Platform mounted of Size 600x500x450mm, Dust & Vermin Proof (IP-64), Epoxy Powder coated, Front & Rear Opening, Double Door Shutters with Locking Arrangements, Feeder Pillar Box having Epoxy Powder coated, mounted on Mild Steel Angle Iron Frame 50x50x6.0mm and not less than 600mm Height from Natural Ground Level, grouting Angle Iron Legs in Cement Concrete 1:2:4 (20mm graded stone aggregates) Block of Size 300x300x600mm including necessary Formwork, Earthwork, expossed Angle Iron Frame shall painted with Two Coats of Synethetic Enamel Paint over a Coat of Red Oxide Zinc Chrome Primer, Providing all Electric Connections and Testing and Comprising with the following including Taking down/ out Unserviceable Feeder Pillar Box and Connected Items of any description, complete all as specified and as directed :- INCOMMING :- (a) Copper Bus-bar 200 Amp, 4 Strip, installed on Porcelain/ Epoxy - 01 Set Insulators (b) MCCB 63 Amp, 4 Pole, 16 kA, 415 Volt - 01 No. OUTGOING :- (a) MCB 40 Amp, SPN, 10 kA, 240 Volt - 04 No. (b) Digital Amp Meter 0-200 Amp Square Flush Pattern - 01 No. (c) Digital Voltmeter 0-500 Volt, Square Flush Pattern - 01 No. (d) LED Indicator Lamp (RYB) in Incomming Phase - 01 Set (e) Internal Wiring with PVC insulated Copper Conductor Multi-stranded Cable 1100 Volt, IS:694 marked of appropriate Gauge including all Copper Lugs (f) MCCB shall be provided with suitable Spreaders of Copper Conductor for fixing of Incoming Cables (g) Connection from MCCB to Bus-bars with Solid Copper Conductor.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of Size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/ out Unserviceable Earthing of any description, complete all as specified and as directed.

Supply & laying Steel Water Tubing 25mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, laid in Trenches or any other Situation, complete as all specified and as directed. NOTE : Necessary Earthworks will be Measured and Paid separately under appropriate Items.

Supply & laying Steel Water Tubing 32mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, laid in Trenches or any other Situation, complete as all specified and as directed. NOTE : Necessary Earthworks will be Measured and Paid separately under appropriate Items.

S&F Gun Metal Globe/Gate Valve 25mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed.

M&L Drilling and Tapping Galvanised Steel Water Tubing 25/32mm bore (dia) and connecting the Water Mains (in Position) for Branch Connections, complete all as specified and as directed.