CERTAIN SPECIAL REPAIR, LBW WORKS, REVENUE WORKS AND MINOR WORKS AT DAMANA UNDER GE JAMMU

Amount

B/R Portion:- M&L Construction of septic tank for 250 users, exc in ordinary soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC Slab covers including RCC precast manhole covers having 6mm plate embedded allround/fibre reinforced cover with angle iron frame Vent Shaft and sludge chamber etc complete all as specified and as shown in Drg No CEPZ-C-TD-13/01-05.

M&L for Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc and n.exc 10 Sqm on plan and n.exc 1.5 mtr in depth and getting out in any type of soil complete all as specified and as directed.

M&L for Returning, Filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and as directed.

M&L for removing excavated soil up to a distance 1.5Km and depositing where directed complete all as specified and as directed.

M&L for concrete bed to drain pipes of bore 150mm dia including packing under haunching against the sides of pipe after they are laid tested in cement concrete 1:4:8 type C-2 using 40mm graded crushed stone aggregates complete all as specified and as directed.

M&L for 150mm internal dia salt glazed stone ware drain pipes Class "A" laid in trenches on concrete bedding jointed in cement mortar 1:1 complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation, filling in and mass concrete complete all as specified and as directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exc. 6m mean radius built in cement mortar 1:4 complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in benching, coping etc including necessary form work complete all as specified and as directed.

M&L for Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surface finished even and smooth without using extra cement including mixing of integral water proofing compound in the proportion as per manufacturer's instructions complete all as specified and as directed. Note:- Water proofing compound will be paid separately under respective items.

Supply only liquid water proofing compound complete all as specified and as directed.

M&L for Pre-cast RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in manhole cover, slab fixed in position including necessary form work and set in CM 1:6 complete all as specified and as directed.

M&L mild steel TMT 10mm dia and over cut to length, bent to shape, required including cranking, bending, spirally for hopping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

All as per Ser Item No 13.00 here-in-above but 5mm dia and over upto and including 10mm dia as in Binders, stirrups, spacer complete all as specified and as directed.

M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in surface channels and drains etc complete all as specified and as directed.

S&F sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm X 460mm bowl size 410mm X 330mm X 160mm including waste coupling complete all as specified and as directed.

S&F 40mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc complete all as specified and as directed.

M&L Cutting holes in brick walls exc. Half brick but n.exc one brick built in cement mortar or cement lime mortar for inserting hold fast or GI pipe and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 complete all as specified and as directed.

M&L 15mm bore GI tubes medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F Chromium plated fancy type Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F stainless steel grade 430, glossy finish, wall hanging plate rack inclusive of spoon hanger, made out of 1mm thick sheet of size 750 X 600 X 250 mm having partition as per sample kept in AGE B/R Office and fixed with steel fasteners or steel screwed complete all as specified and as directed.

M&L for Brick work in cement mortar 1:6 using sub class 'B' bricks straight or curved on plan exceeding 6m mean radius complete all as specified and as directed by Engineer-in-Charge.

All as per Ser Item No 22.00 here-in-above but except bricks complete all as specified and as directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc (inner girth only measured) complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15cm thickness (below or above ground level) and removing unserviceable material exc 100 mtr complete all as specified and as directed.

M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L Preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

S&F 1.25mm thick steel rolling shutters, without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete but gear operated type with bevel gear box and crank handle complete all as specified and as directed.

M&L for preparation of new steel surface of any description over 10cm in width or girth not otherwise described and applying two coat of synthetic enamel paint complete all as specified and as directed.

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed.

M&L Ball bearing for rolling shutters complete all as specified and as directed.

Dismantling asbestos cement (corrugated or semicorrugated etc) sheets in roof covering complete all as specified and as directed.

Dismantling timber scantling 40 sqcm and over in section framed work of any description complete all as specified and as directed.

Dismantling ceiling boards (fibre, pulp, insulation) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified and as directed.

M&L for clean sawn timber in fixed second class soft wood in scantlings complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Refixing ceiling boards as obtained from dismantling in Ser Item No 34.00 here-in-before complete all as specified and as directed.

M&L for providing cement concrete type B-0 1:2:4 (12.5mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

Hardcore of gauge not exc 63mm deposited spread and levelled in layers n exc 15cm thick, watered and rolled/rammed to a true surface using broken stone or boulders complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 using 40mm graded aggregates as sub base in floor surface complete all as specified and as directed.

M&L chequered cement concrete tiles 20cm X 20cm X 25mm thick, jointed with grey cement and no pigment and pointed in neat cement slurry complete all as specified and as directed.

M&L Construction of septic tank for 10 users, exc in ordinary soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC Slab covers including RCC precast manhole covers having 6mm plate embedded all round/fibre reinforced cover with angle iron frame Vent Shaft and sludge chamber etc complete all as specified and as shown in Drg No CEPZ-C-TD-13/01-05.

M&L for 100mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and as directed.

M&L PCC 50mm thick type B-1 1:2:4 (20mm graded aggregate) as in filling with finishing surface even and smooth without using of extra cement complete all as specified and as directed.

M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and as directed.

Rendering 10mm thick on brick work or concrete surfaces in cement mortar 1:4 complete all as specified and as directed.

M&L glazed ceramic tiles in vertical surface (300 X 200 X 7mm) thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed.

M&L PCC 75mm thick type B-1 1:2:4 (20mm graded aggregate) as in filling with finishing surface even and smooth in plinth protection complete all as specified and as directed.

M&L for preparing plastered surfaces and applying two coat of cement base paint complete all as specified and as directed.

M&L framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed.

S&F Welded steel wire fabric supplied and fixed complete to wood or steel members n.exc. 4.00 Kg complete all as specified and as directed.

Septic tank exc in ordinary soil, Fdn in PCC 1:2:4, brick work in CM 1:4, RCC slab covers including RCC Pre cast manhole cover having 6mm plate embedded all round/fibre reinforced cover with angle iron frame vent shaft and sludge chamber complete for 25 users all as specified and as directed.

Cutting into existing manholes for connecting new drain 150mm dia making good to pipe and rendering cutting out existing for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete all as specified and as directed.

Taking down chowkhats or frames with shutter without taking off shutter from the frame n.exc. 1.5 sqm each including cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and as directed.

Taking down chowkhats or frames with shutter without taking off shutter from the frame exc. 1.5 sqm but n.exc. 4 sqm each including cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and as directed.

Dismantling wooden framed trusses span n.exc. 10m complete all as specified and as directed.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches pillars etc and removing unserviceable material exc 100 mtr complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including racking out joints hacking for key scrubbing with water etc complete all as specified and as directed.

Pressed steel frames for door (Factory made) out of 1.25 mm thick black MS sheet with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate etc complete size of frame 125 X 60mm incl bottom of each chowkhat to be welded with 2 No's 25 X 25 X 3mm thick flat iron projecting 10 cm on either side and back fill to chowkhats with PCC 1:3:6 type C-0 using 12.5mm graded crushed stone aggregate including one shop coat of red oxide primer complete all as specified and as directed.

S&F for 35mm thick 2nd class hard wood plain framed, panelled shutter (two panel) of factory made with lock rail and panel of 12mm thick veneered particle board with commercial veneering on both faces including wooden beads on both sides, one coat of pink primer. The size of rail and stile as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F for 35mm thick 2nd class hard wood factory made glazed and Skelton shutters open rebated and prepared to receive glass/wire gauge etc. without sash bar but with lock rail edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass/wire mesh etc sizes of member as per clause 8.20 (a) of SSR Part-I for door shutter complete all as specified and as directed.

S&F steel window/ventilator 1.25mm thick Box type (Primer coated) ERW hollow P section of size 60 X 25mm single rebated comprises glazed Skelton shutter ERW sec 50 X 20 mm and 1mm thick with two No's sash bar of T-section 20mm X 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60 X 25 mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window incl following fitting welded to frame shutter hold fast of 150mm long of 12mm X 3mm FI made to shape 4 No, handle of Z section 20mm X 25mm X 100mm long 1 No per leaf, MS tower bolt 150mm long 2 No per leaf, Z sec 20mm X 25mm, 100mm long stopper 1 No on per leaf, MS pintal hinges of size 75mm X 12mm 2 No per leaf fabrication and fixing arrangement as per drg No CEPZ/TD-324,325/07 complete all as specified and as directed.

S&F steel window/ventilator 1.25mm thick Box type (Primer coated) ERW hollow P section of size 60 X 25mm single rebated comprises wire gauged Skelton shutter ERW sec 50 X 20mm and 1mm thick with two Nos of Fi section complete welded to frame for holding wire mesh with one vertical mullion of ERW box type T-section of size 60 X 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each window incl following fitting welded to frame shutter hold fast of 150mm long of 12mm X 3mm FI made to shape 4 No, handle of Z section 20mm X 25mm X 100mm long 1 No per leaf, MS pintal hinges of size 75mm X 12mm 2 No per leaf fabrication and fixing arrangement as per Drg No CEPZ/TD-324,325/07 complete all as specified and as directed.

S&F Mild steel work of flat iron, square bar, round bar etc as in framed work such as grills, guard bars, gratings etc including bending, cutting and welding as necessary of confirming to Fe 290-0 Gde E-16 including one shop coat of red oxide primer complete all as specified and as directed.

S&F 3mm thick sheet glass ordinary quality glazing with steel pins, oil putty to steel windows and beads, nails etc to wooden surfaces as in square exc 0.50 Sqm in each pane complete all as specified and as directed.

M&L for Rendering 15mm thick cement plaster in cement mortar (1:4) on fair face of brick work or concrete surfaces of wall and to be finished even and smooth without using extra cement complete all as specified and as directed. (including all necessary scaffolding, lifting arrangement).

M&L for preparation of new wood or wood based surface and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

M&L for two coats of oil bound distemper of wall to newly plastered surfaces including preparation of surfaces with wall putty and cement primer complete all as specified and as directed.

M&L for two coats of oil bound distemper to old treated surfaces including preparation of surfaces with wall putty and cement primer complete all as specified and as directed.

S&F Anodised aluminium snap grid work of size 605 X 605mm for false ceiling complete all as specified and as directed.

S&F for 4mm thick non asbestos fibre cement building boards 60 X 60cm in size including two coat of white wash after preparation of surface, fixed/laid/inserted to GI frame work at ceiling with screws complete all as specified and as directed.

Supply and fixing Galvanised steel tube of 100mm of medium grade complete all as specified and as directed.

S&F for structural steel works of Fe 410W (Gde E 250) quality A, as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc including painted one shop coat of zinc chromate/red oxide primer paint (including preparation of surface) before fabrication complete all as specified and as directed.

S&F Plates (Plain or chequered channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18-20mm thick laid over and including cement screed base 20mm thick in cement mortar 1:6, over and including 25mm thick PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and polishing to granite finish over complete all as specified and as directed.

M&L for machine cut kota stone slab flooring 18-20mm thick as in riser of steps, skirting, dado and pillar laid over and including rendering of 15mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and polishing to granite finish complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C-2 using 40mm graded stone aggregate as in plinth protection etc finished even and smooth without using extra cement complete all as specified and as directed.

Preparation of old plastered surface including filling of small holes etc and applying two coats of cement based paint complete all as specified and as directed by Engr-in-Charge.

S&F in repair MS PVC coated drapery rods of 25mm dia complete with coloured conical end balls at both end, dia not less than 50mm and fitted with and including MS PVC sheeted/power coated bracket size 150mm made to shape or 75mm dia PVC/PVC coated coloured end wall to wall round block made to shape in male and female pieces as required at site complete all as specified and as directed.

S&F mild steel work of angle iron as in framed work such as cooler stand, grills, gratings etc with ends of bars shouldered and/or riveted, or forged into spikes; confirming to Fe 290.Gde-E-165 complete all as specified and as directed.

Cutting holes into or through brick wall built in cement mortar, superficial area n.exc 150 sq.cm and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and as directed.

M&L Reinforced cement concrete (nominal mix) in type B-1 1:2:4 (20mm graded crushed stone aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span, as in lintel band complete all as specified and as directed.

Use and waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floors and roofs not exceeding 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide for rough finished surfaces complete all as specified and as directed by Engr-in-Charge.

S&F Pressed steel frames of size 105 X 60mm for door (factory made) out of 1.25mm thick black MS sheet, with one or more rebates including necessary fixing lugs, butt hinges, lock strike plate etc complete all as specified and as directed.

Hacking out old broken glass of any thickness, size, quality or description from the wooden frames glazing with putty or fixed with wooden beads complete all as specified and as directed.

S&F in repairs Galvanised mild steel wire cloth, 0.46mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

M&L for PCC 1:2:4 type B-0 (using 12.5mm graded aggregate) as in blocks for hold fasts, backfilling, benching, coping, apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed. Note:- Formwork required for these items included in the unit rate of this item.

Dismantling structural steel work including doors, gates of any description complete all as specified and as directed.

Supply and fixing curtain rails, mild steel, coloured fancy type with both side fancy cup and brackets complete all as specified and as directed.

S&F for frame work for ceiling with specification as under mentioned:- (i) GI section frame work (Powder coated) for white, pre-premiered, self embossed, reinforced designer board consisiting of perimeter wall angle 19mm X 19mm X 0.45mm, cross 'Tee' 28.6mm (web) X 24mm flange 0.33mm thick powdered coated main tee 38mm (Web) X 24mm flange 0.33mm thick. wall angle shall be screwed/fixed to brick wall/partition wall/concrete/RCC with the help of nylon sleeves and screws @ 610 mm C/C, then suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220mm C/C to soffits. To from grid of 610 X 610mm cross Tee shall be provided @ 610mm C/C in both directions and all suitable provisions shall be made for fixing the recessed/surface mounting light fittings if any, complete all as specified and as directed by Engr-in-Charge.

M&L for mild steel screw bolts (machine made) with hexagonal or square heads at one endand screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5cm and n exc 30cm long, Diameter of neck 16mm to 20mm complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and as directed.

M&L for non skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

S&F Aluminium handle cast type, anodised size 150mm long, D type complete all as specified and as directed.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F Aluminium anodised, barrel tower bolts of extruded section and fixed size of bolt 150mm complete all as specified and as directed.

M&L for two coat of synthetic enamel paint on old steel surfaces of any description not otherwise described over 10 cm width or girth including preparation of surface complete all as specified and as directed.

M&L applying two coats of synthetic enamel paint on old wooden surface including preparation of new surface over 10 cm width or girth complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm but n exc 2 sqm and refixing in same opening complete all as specified and as directed.

M&L for RCC 1:1.5:3 type A-1 using 20mm graded stone aggregate as in beams, cantilevers, lintels over 1.5m span complete all as specified and as directed.

M&L for RCC 1:1.5:3 type A-1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies and in shelves and the like complete all as specified and as directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressemers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc for fair finished surfaces complete all as specified and as directed by Engr-in-Charge.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs n.exc. 200mm thick complete all as specified and as directed.

M&L rendering 05mm thick in cement mortar 1:3 on fair faces of brick work or concrete surfaces finishing surfaces even and smooth without using extra cement as in ceiling complete all as specified and as directed.

M&L for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash including preparation of newly plastered surfaces complete all as specified and as directed.

M&L Moorum/Red Bajri/approved earth filling in floors or pavings, laid in layers n.exc 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

S&F 100mm size butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and as directed.

S&F Steel water tubing 20mm bore medium grade galvanised with all fittings including short lengths, fixed to walls, or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc) complete all as specified and as directed.

S&F for PVC door frame made out of PVC sheet of size 90mm X 55mm filled in to (PUF) Poly Urethane Foam with single rebate as per Drg No CWE/TD-150/12Sheet 1/1 complete all as specified and as directed.

S&F factory made single piece solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for style and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement supply and fixing in the frame at site complete all as specified and as directed.

S&F in repair water closet (Squat pattern) with lime concrete bedding, vitreous china orissa pattern 580 X 440mm, white with integral foot rests (excluding flushing cisterns and flush pipe) including connection to trap and to flushing pipe, antisyphonage pipe etc complete including making good to floor complete all as specified and as directed.

S&F Vitreous china bowl urinal flat back size of 465 X 355 X 265mm white including waste pipe 32mm dia GI pipe, grating and brass union for discharge pipe complete including providing and fixing plug bedding urinal against wall in cement mortar 1:2 securing urinal to plug with and including 60mm long brass screw pointing around urinal black in cement etc complete all as specified and as directed by Engr-in-Charge.

Supply & Fixing 10 ltr capacity PVC valveless, syphonic action type flushing cistern low level white with inlet, ball valve, float and handle including connection to pipe complete all as specified and as directed.

S&F vitreous china wash hand basin white flat back of size 550 X 400mm with pedestal including bracket, cutting for and pinning the ends of brackets or erecting stands exclusive of waste pipe but including brass chromium plated waste coupling with long screwed sank and fly nuts complete all as specified and as directed.

S&F stainless steel soap dish bar fixed with and including Chromium plated brass screws and wooden/plastic cleats (minimum weight 300 gms) complete all as specified and as directed.

S&F towel ring of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats complete all as specified and as directed.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part - I of capacity 500 ltr complete all as specified and as directed.

S&F Stop valve, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15mm complete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S&F Ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe and fixed. (minimum weight 210 gms) complete screwed for iron pipe or brass ferrule of size 20mm bore complete all as specified and as directed.

S&F 110mm PVC (SWR), waste and vent pipes in any length with or without ears, with rubber ring joints laid in trenches or in floor complete all as specified and as directed.

S&F 110mm dia PVC Bends (any radius) diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

S&F grating doom 100mm dia of PTMT (minimum weight 25 gms) complete all as specified and as directed.

S&F PVC (SWR) P trap 110/110mm bore complete all as specified and as directed.

S&F Pillar tap, cast copper alloy with capstan heads, Chromium plated, screed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe of bore 15mm complete all as specified and as directed.

M&L for 40mm thick average sand filling as screed bed for laying interlocking paving block including watering and consolidation complete all as specified and as directed.

M&L for machine pressed pre cast concrete inter locking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment complete all as specified and as directed.

S&F precast PCC 1:2:4 type B-1 (using 20mm graded aggregate) kerb stone of size 150mm X 125mm and 300mm height, chamfered at one end (75mm X 75mm) fixed vertically and set in CM 1:4 complete all as specified and as directed.

E/M Portion:- Taking down old/UNSV copper/aluminium point wiring (light, fan, bell, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody for taking credit complete all as specified and as directed.

Taking down DB's, main switches etc of any size making good disturbed surface of wall/floors etc complete all as specified and as directed.

M&L for point wiring for one light/fan point/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 Sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into existing concealed PVC rigid/steel conduit and into existing CI/pressed steel terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and as directed. Note:- (a) Wiring shall be done by using proper colour coding. (b) Earth wire shall be of green colour. (c) On RCC roof/ceiling PVC conduit shall be provided on surface with proper fixing clips complete all as specified and as directed by Engr-in-Charge.

All as per Ser Item No 135.00 here-in-before but for multi 3/5 pin socket outlet 5 amp socket on independent board complete all as specified and as directed.

All as per Ser Item No 135.00 here-in-before but for multi 5 pin 5 amp socket outlet on same board complete all as specified and as directed.

All as per Ser Item No 135.00 here-in-before but for one 3 pin socket outlet 15 Amps on independent board with cables 2.5 Sqmm size complete all as specified and as directed.

S&F Socket outlet 3/5 Pin, 5A, flush type complete all as specified and as directed.

S&F angle/batten lamp holder on PVC square Blocks with PVC insulated body complete all as specified and as directed.

S&F LED Bulb 9 Watt 240 Volts complete all as specified and as directed.

S&F in replacement Stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified and as directed.

S&F in replacement for switch piano, flush type single pole one way 5 Amp, 240 volts complete all as specified and as directed.

M&L for replacement distribution board sheet steel phosphatised powder coated for MCB with one copper bus bar and neutral link earthing stud SPN 12 way 240 volts double door complete all as specified and as directed by Engr-in-Charge. Note:- Distribution board and MCB's should be of same make.

S&F ceiling rose 3 phase/PVC/polycarbonate isolated body complete all as specified and as directed.

S&F in replacement new generation energy saving, wall mounted LED Tube light batten fittings, extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver 20 Watt LED 6500K (4' ft long) with LED rod 20 watt, 230 Volts 50 Hz complete all as specified and as directed.

S&F in repair MCB single pole and Neutral 32 Amp suitable for 240 Volt, 'B' series complete all as specified and as directed.

S&F in replacement for MCB SP 32 Amps 240 Volts, 'B' series complete all as specified and as directed.

Supply and laying or fixing or passing through pipe 1100 Volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 16 Sqmm nominal cross section 2 Core in service connection complete all as specified and as directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60cm X 60cm X 6.3mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in Electrical plate No 5 of SSR Part - I including necessary excavation and earth work GI pipe 20mm dia light grade for watering and GI 15mm dia light grade pipe for protection of GI earth wire etc PCC chamber with RCC cover in cement concrete 1:2:4 type B-1 (20mm graded aggregate) funnel, wire mesh, charcoal dust, salt layers each layer thickness should be 15cm (Layer start from below the electrode plate to above plate) etc connected to LT panel board as indicated including testing on completion complete all as specified and as directed.

Taking down of LT cable of any size in walls, trenches etc and making good to the disturbed surfaces of wall/floors etc in any size complete all as specified and as directed.

M&L for replacement distribution board sheet steel phosphatised powder coated for MCB with one copper bus bar and neutral link earthing stud SPN 4 way 240 volts double door complete all as specified and as directed by Engr-in-Charge. Note:- Distribution board and MCB's should be of same make.

M&L sheet metal enclosure (factory made) double door for distribution board (when MCB's are to be used) Single pole neutral 240 Volts, 8 ways with 200 Amp rated bus bar connection with suitable size complete all as specified and as directed.

Supply and fixing LED tubelight fittings 18 watt wall mounted LED bateen rod extruded aluminium heated sink provided for efficient heat dissipation and integrated electronic driver complete all as specified and as directed.

S&F in repair MCB single pole 6-32 Amps suitable for 240 Volts, 'B' series complete all as specified and as directed.

M&L switch piano flush button single pole one way 15 Amp complete all as specified and as directed.

M&L socket outlet 3, 5 pin and 15 Amp multipurpose shuttered type complete all as specified and as directed.

Supply and laying or fixing or passing through pipe 1100 Volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 10 Sqmm nominal cross section 2 Core in service connection complete all as specified and as directed.

M&L for point wiring for one light or one fan point controlled by one switch complete with 1.50 Sqmm copper conductor, multistrand PVC insulated FRLS and unsheathed cable in existing PVC rigid concealed conduit with New cast iron/pressed steel sunk terminal box with 3mm thick laminated sheet hylam brand IS-2036 marked with continuous PVC insulated multistrand copper wire 1.50 Sqmm dia FRLS PVC insulated complete all as specified and as directed. Note:- (a) Wiring shall be done by using proper colour coding. (b) Earth wire shall be of green colour. (c) On RCC roof/ceiling PVC conduit shall be provided on surface with proper fixing clips complete all as specified and as directed by Engr-in-Charge.

All as per Ser item No 159.00 here-in-before but for multi 5 pin 5 amp socket outlet on same board complete all as specified and as directed.

M&L sub main wiring with two single core copper conductor 6 Sqmm multistrand PVC insulated FRLS and unsheathed cable with proper colour coding as red for phase, black for neutral and including PVC rigid concealed conduit with necessary fittings and fixtures etc and continuous PVC insulated multistranded copper earth wire 4 Sqmm dia in green colour complete all as specified and as directed. Note:- All the three wires will be measured as one run.

M&L sheet metal enclosure (factory made) double door for distribution board (when MCB's are to be used) Single pole neutral 240 Volts, 4 ways with 200 Amp rated bus bar connection with suitable size complete all as specified and as directed.

S&F in repair MCB single pole and neutral 16 Amp, 'C' series suitable for 240 Volt complete all as specified and as directed.

S&F in repair MCB single pole 6-10 Amp, 'B' series suitable for 240 Volt complete all as specified and as directed.

S&F medium grade 20mm GI pipe light grade with complete fitting such as elbow, union, socket etc as per site requirement and laid in trenches complete all as specified and as directed.

S&F Gun metal, globe or gate valve 20mm ISI mark with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repair LED street light fittings, 45 Watt, powder coated pressure die cast aliuminium compact high power LED street light with heat resistant toughened glass with lens complete with suitable bracket, clamps and suitable length twin core wire including taking out old unsv pole complete all as specified and as directed. Note:- Rate is inclusive of bracket of suitable size made of GI medium grade pipe 1.2 mtr long bend to shape 120 degree and fixing with 2 No's of suitable sizes clamps including nuts, washers, bolts complete fittings.

Labour for cutting of existing pipe line of any size for making suitable connection for 20mm dia pipe including all type of fitting complete all as specified and as directed. Note:- Earth work and welding of pipe line are included in above said rate.

Jagbir Singh and Co

MADHAV CONSTRUCTION COMPANY

Bidder Name

MADHAV CONSTRUCTION COMPANY

Jagbir Singh and Co

M/s Koul & Sons