Construction of Digital Class room Building at Naharkatiya College Campus (Civil and Electrical works) At Naharkatiya College

Amount

PART -A ( DISMANTLING AND DEMOLISHING WORKS )

Demolishing RCC work including stacking of steel bars and disposal of unserviceable material as directed for all levels.

Demolishing brickwork including stacking of serviceable materials and disposal of unserviceable materials as directed for all levels

Dismantling all types of corrugated / trapezodial sheet roofing including ridges, hips, valleys and gutters etc and stacking the materials as directed by the department for all levels.

Dismantling steel work in built up section in joists, angles, channels, tees, flats etc including all gussety plates, bolts, nuts, cutting rivest, welding etc. including dismembering and stacking the materials as direced by the department.

Dismantling all types of ceiling, partition and wall lining and stacking the materials as directed by the department for all levels

Dismantling of existing steel windows/ steel ventilators/ steel windows and steel ventilators without damaging the walls, removing to a safe place and necessary repairs to the edges of walls.

PART -B (GROUND FLOOR )

Earthwork in excavation in foundation trenches of walls, retaining walls, footing of column, steps, septic tank etc., including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all leads and lifts as directed and specified in the following classification of soils including bailing and specified (A) Up to a depth of 2.00m below the existing ground level (a) In ordinary soil

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a) Brick on flat soling

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary and curing complete (shuttering where necessary shall be measured and paid separately) (b) In prop 1 cement: 4 sand: 8 coarse aggregate by volume

Providing and laying plain/reinforced cement concrete works cement, coarse sand and 20mm down graded stone aggregate including dewatering if necessary and curing complete but excluding cost of form work and reinfor cement for reinforced cement work (form work and reinforcement will be measured and paid separately) (I) Using Mixer Machine (A) In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level N) without using admixture, plasticiser

(B) In superstructure from plinth level up to 1st floor level ii) Columns, pillars, posts, strut, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, grider, bressummer, cantilever, staircase (exceptspiral staircase and landing) including preparing the top surface and finishing of noising. N) without using admixture, plasticiser

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in (i) 3.1.1.1 Foundation, footing, base of column, pile cap, raft and mass concrete works etc (b) Using 25mm thick plank

(ii) 3.1.1.2 Side of tie beam, grade beam etc at or below ground level (b) Using 25mm thick plank

(iii) 3.1.1.4 Sides and soffits of Beams, beam haunchings, cantilever griders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M (i) Using 25mm thick plank

(iv) Flat surface such as soffits of suspende floors, roofs, landings, cantilever slabs, chajjas, balconies and the like.

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (ii) Super Ductile (SD) TMT reinforcement bars (a) From Primary Producer :- TATA/SAIL /Jindal Steel/Shyam Steel.

(c) ISI approved Mild steel reinforcement bar(M.S. Bar)

112mm thick brick wall with 1st class brick nogged wall in cement mortar including racking our joints ad curing complete as directed in super structure above plinth upto 1st floor level (Protruding M.S. ro/ Tor Steel of column to be embedded in cement mortar and will be measured and paid separately) (a) In cement mortar in proportion 1:4 (1 cement : 4 sand)

15mm thick cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed B) On fair side b) In cement mortar 1:4

Supplying, fitting and fixing door frame made of M.S. equall angle of size 40mm x 40mm x 5mm fabricated, welded, nitred and joined as per relevant I.S codes including fitting 8 nos of M.S. hold fast, providing closing. holding device for 2 nos tower bolts of door for each side and 1 no for fitting and fixing Aldrop (for single leaf) to the frame for fixing the door to the frame, aplying primer to all steel surfaces fixing the frame to the wall/ R.C.C. members by embedding the hold fast securely in C.C. block of M-15 grade complete at all levels as specified and directed. (Door hinges to be paid as per relevant item of the schedule of rates.)

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevant I.S. code including oxidised iron butt hinges (100mm x 75mm x 3.5 mm) 6 nos with necessary wood screws. a) Decorative type face panel and block board core. (i) 40mm thick

Providing, fitting and fixing steel windows of standard rolled steel sections as per relevant I.S. coe, joints mitred and welded with 15mm x 13mm x 100mm lugs embedded in cement concrete block of M-10 grade including providing and fixing of projecting hinges (not more than 65mm and not less than 15mm wide) bolting device, steel handles, pegs, stays of 300mm long etc. complete including providing 12mm x 12mm sq. bars duly welded to steel frame at nore than 12cm c/c applying a priming coat of red-lead paint ect. complete as per drawing. (a) Openable

Wall painting (two coats) with acrylic emulsion paint approved brand and manefacture (Asian Paint/ Berger Paint/ ICI paint/ J& N Paint/ Nerolac) on new surface to give and even shade after throughly brushing the surfaces free from mortar droppings and other foreigh matter and sand papered smooth. (a) Acrylic Emulsion paint approve brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J& N Paint/ Nerolac)

40mm thick cement concrete floor consisting of 25mm under layer of cement concrete in prop 1:3:6 (1cement:3 coarse sand: 6 coarse aggregate of 12.5mm and down) and 15mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement: 1 coarse sand: 2 coarse aggregate of size 10mm down) finished with a floating coat of eat cement finish using cement slurry for bond @ 2.74 kg. per square metre of floor are, wearing layer is to be laid in panels including curing etc complete as directed.

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N Paint/ Nerolac) to give and even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. (i) Surfaces over 100mm in width or girth (b) High gloss (Asian paint/ Berger paint/ ICI paint/ J & N Paint/ Nerolac)

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture (Asian Paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter (i) Surfaces over 100mm in width or girth (b) High gloss (Asian Paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Supplying, fitting, fixing stainless steel fittings of approved make, resonable smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc complete. (Bright natural matt & Satin finished) a) Sliding door bolt (iii) 200mm x 16mm

c) Door handle (iii) 150mm

PART -C 1st FLOOR (A-TYPE)

Providing and laying plain/reinforced cement concrete works cement, coarse sand and 20mm down graded stone aggregate including dewatering if necessary and curing complete but excluding cost of form work and reinfor cement for reinforced cement work (form work and reinforcement will be measured and paid separately) (I) Using Mixer Machine (B) In superstructure from plinth level up to 1st floor level ii) Columns, pillars, posts, strut, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, grider, bressummer, cantilever, staircase (exceptspiral staircase and landing) including preparing the top surface and finishing of noising. N) without using admixture, plasticiser a) M15 grade concrete or prop 1:2:4

Providing form work of ordinary timber planking so as to give a rough finish including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in-situ reinforced concrete and plain concrete work in (i) 3.1.1.3 Column, Pillars, Post and Strut (ii) Using 25mm thick plank

(ii) 3.1.1.4 Sides and soffits if beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (ii) Using 25mm thick plank

(iii) 3.1.1.5 Flat surfaces such as soffits of suspended floors, roofs, landings, cantilever slabs, chajjas, balconies and the like (ii) Using 25mm thick plank

112mm thick brick wall with 1st class brick nogged wall in cement mortar including racking our joints ad curing complete as directed in super structure above plinth upto 1st floor level (Protruding M.S. ro/ Tor Steel of column to be embedded in cement mortar and will be measured and paid separately) (a) In cement mortar in proportion 1:4 (1 cement : 4 sand)

15mm thick cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed B) On fair & rough side b) In cement mortar 1:4

Supplying, fitting and fixing door frame made of M.S. equall angle of size 40mm x 40mm x 5mm fabricated, welded, nitred and joined as per relevant I.S codes including fitting 8 nos of M.S. hold fast, providing closing. holding device for 2 nos tower bolts of door for each side and 1 no for fitting and fixing Aldrop (for single leaf) to the frame for fixing the door to the frame, aplying primer to all steel surfaces fixing the frame to the wall/ R.C.C. members by embedding the hold fast securely in C.C. block of M-15 grade complete at all levels as specified and directed. (Door hinges to be paid as per relevant item of the schedule of rates.)

Providing, fitting and fixing steel windows/ ventilators (openable) of standard rolled steel sections as per relevant I.S. code - 1038 joints mitred abd welded with 15mm x 3mm x 100mm lugss embedded in cement concrete block of M-10 grade including providing and fixing of projecting hinges (not more than 654mm and not less than 15mm wide) bolting device and steel handles, peg stays of 300 mm long etc. complete as per drawing icluding applying a priming coat of red lead paint.

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevant I.S. code including oxidised iron butt hinges (100mm x 75mm x 3.5 mm) 6 nos with necessary wood screws. a) Decorative type face panel and block board core. (i) 40mm thick

Wall painting (two coats) with acrylic emulsion paint approved brand and manefacture (Asian Paint/ Berger Paint/ ICI paint/ J& N Paint/ Nerolac) on new surface to give and even shade after throughly brushing the surfaces free from mortar droppings and other foreigh matter and sand papered smooth. (a) Acrylic Emulsion paint approve brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J& N Paint/ Nerolac)

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) (ii) Super Ductile (SD) TMT reinforcement bars (a) TATA/SAIL/Jindal Steel/Shyam Steel)

(c) ISI approved Mild steel reinforcement bar(M.S. Bar)

Providing, fitting, hoisting and fixing of roof trusses fabricated using any one or combination of following ections of (i) square section (ii) Rectangular hollow section of specification SHS/RHS and including purlins, bottom runners and providing M.S. cleats, M.S. angle base plant, blts and nuts with red oxide primer including fitting bottom runners and cleat etc. for fixing ceiling joist as per design complete as directed as per specification. Main Building

Providing pre painted galvanized iron sheet roofing (PPGI) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof Trusses, purlins etc. to be measured and paid separately). TATA blue scope/ Dyna roof/ wonder roof or equivalent as directed by the Department. (ii) 0.45mm thick

Providing pre painted galvanised iron sheet (PPGI) accessories (Ridges/ Valley/ Gutter/ Flashing)at all levels including fitting and fixing self drilling, self tapping screws completye. TATA Blue scope/ Dyne Roof/ Wonder Roof or equivalent as directed by the department. (ii) 0.45mm thick

Providing creamic tiles of approved quality, size and shape and thickness not less than 8mm on floors, skirtings, treads and risers of steps over cement mortar bed 15mm thick in prop 1:3(1 cement : 3 sand) including cutting where necessary finished with flush pointing with fix-A tile choksey/ Sika/ Pedelite/ Rouf/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (coloured pigment should be in conformity with colour of slab and as approved and directed by the department) c) Delux range (Somany/ Orient/ Nitco/ Qutone make) iii) Of size 600mm x 600mm and above

Supplying, fitting, fixing and painting where necessary (one coat primer and two coats of paint) M/F suspended ceiling which includes GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a swb f 7mm) along with perimeter of ceiling, screw fixed to brick wall / pertition with th help of nylon sleeves and screws at 610mm c/c. Then suspending GI intermediate channels of size 45mm (0.9mm thick with two equal flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angle of width 25mm x 10mm x 0.55mm thick fixed to soffit with GI cleat and steel expansion fastener. Ceiling section of 0.55 mm thickness having knurled web of 51.5mm and two equal flanges of 26mm eacg with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 457mm c/c, 9.5mm / 12.5 mm tapered edge GYPboard (conforming to IS:2095-1982) is then screw fixed ro ceiling section with 25mm long dry wall screws at 230mm c/c. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally, the boards are to be jonted and finished so as to have a flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, joint paper tape and two coats of drywall topcoat suitable for GYPboard complete at all levels as specified and directed. (For light fittings, providing opening for doors, windowsm ventilators etc, cut out made with frame of perimeter channel supproted suitably to be measured and paid separately where necessary). (ii) 12.5mm thick

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N Paint/ Nerolac) to give and even shade including cleaning the surfaces of all dirt, dust and other foreign matter sand papering and stopping. (i) Surfaces over 100mm in width or girth (b) High gloss (Asian paint/ Berger paint/ ICI paint/ J & N Paint/ Nerolac)

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture (Asian Paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter (i) Surfaces over 100mm in width or girth (b) High gloss (Asian Paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)

Supplying, fitting, fixing stainless steel fittings of approved make, resonable smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc complete. (Bright natural matt & Satin finished) a) Sliding door bolt (iii) 200mm x 16mm

b) Door handle (iii) 150mm

Providing and fixing M.S. Tube hand rail of approved size by welding etc to steel ladder, railing, balcony railing, staircase railing and similar works, incuding applying priming coat of approved steel primer complete as specified and directed by department.

Electrical Part

1/1.1 Wiring for light/ fan/ call bell point with 2x1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including 6 Amp flush type switch/ bell push (Anchor Penta/Gold medal /Kolor kany.Kom/ Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor/Gold medal /Kolor kany.Kom / Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the Deptt

1.1.1 Short point up to 3.00 metre. length.

1.1.2 Medium point up to 6.00 metre. Length.

1.1.3 Long point up to 10.00 metre. Length.

2/1.2 Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. marked) with phenolic laminated sheet cover including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete, when placed elsewhere.

1.2.2 Medium point up to 6.00 metre. Length.

1.2.3 Long point up to 10.00 metre. Length.

3/1.4 Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including providing and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. marked) with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete.

1.4.1 Extra Long point up to 15.00 metre. length

1.4.2 Extra Long point up to 20.00 metre. Length.

4/1.8 Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface flat ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) system including earth continuity.

1.8.1 With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in flat 19 mm ISI marked casing 'n' capping system

1.8.3 With 2 x 6 sq. mm. + earth continuity with 1x 4 sq. mm. cable in flat 25mm ISI marked casing 'n' capping system.

5/1.10 Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface flat ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) system including earth continuity.

1.10.4 With 4 x 10 sq. mm. + earth continuity with 2x6 sq. mm. cable in flat 32 mm ISI marked casing 'n' capping system.

6/1.11 Wiring for light/ fan/ call bell point with 2x1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including 6 Amp flush type switch/ bell push (Anchor Penta/Gold medal /Kolor kany.Kom/ Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor/Gold medal /Kolor kany.Kom / Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the Deptt.

6.11.11 Supplying and fixing of batten holder including 11 W CFL lamp and connection as approved by the Deptt.)as required.

7/13.1 Supplying fitting and fixing industrial Plug & Socket in surface mounting SPN sheet steel powder painted MCB DB incorporated with MCB DIN rail, neutral link Earth bar of the following rating of DP MCB complete with making necessary connection etc. as specified and directed by the Deptt.

13.1.1 20A Capacity. (ABB, Schneider MG, legrand, Hager make)

8/15.2 Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door IP-43 surface mounting SPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt.

5.2.1. 4 way SPN double door

5.2.1 8 way SPN double door

5.2.1. 12 way SPN double door

9/16.1 Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.

16.1.2 C Series (Schneider MG, legrand, Hager make)

10/16.6 Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt.

16.6.2 C Series (ABB, Schneider MG, legrand, Hager make)

1/22.1 Supply, installation & testing of Copper Plate earth station with 600 mmx600 mmx3 mm copper earth plate with necessary 40 mm dia. G.I. medium duty watering pipe with G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement with 300 mmx300 mmx6 mm C.I. hinged cover plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

2/22.13 Extra for using salt (5 K and Charcoal (96 K in G.I./Copper plate Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the deptt .

3/22.1 Supplying & laying of 8 SWG Copper. earth from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

14/27.1 Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator].

27.1.1 Premium model 1050 mm Sweep (ORIENT PSPO make)

15/27.6 Supplying fitting & fixing of ceiling fan Regulator including connections etc. complete as required.

27.6.2 Electronic type

16/ECBC3.2.11 BATTEN LIGHT, TMS 020 1X T-5 28 W with 1x28 W T-5 Fluorescent tube. (Philips make or equivalent)

7/11.5 Supplying including fitting and fixing bus bar chamber ( HPL/ GECO / or equivalent make) with 4 strips bus bar of length 450/600/900/1000 mm made of aluminium alloy or wrought aluminium suitable for 200 amp capacity complete with all accessories including connection etc. as required complete

Supplying fixing I.C.T.P and N link Main Switch with rewire able fuses of 500 Volt grade( HPL/ GECO / ANCHOR or equivalent make) including drilling boards/iron frames and fixing with bolts and nuts and connection as approved by the Deptt.)complete as required

100 Amps Capacity T.P. N

18/12.2 Supplying with installation testing and commissioning of Hi -- wall 4 STAR rating non ducted split type air conditioner of the following capacity with cordless remote complete with indoor and outdoor unit, copper pipe and electrical connection as approved by the Deptt.)up to 5 m between the room unit and out door unit as directed by the department.

12.2.4 2 Ton capacity

29.1.3.2(Carrier make) Kurve/ Voltas make) Model PLATINUM 4S

20/31.1 Supplying with fitting and fixing Voltage stabilizer of the following specification complete including making necessary connection as approved, specified and directed by the deptt. (SKYLAND / Vee-Dee / V GUARD / VERTEX/ INDO/ VENUS make)

31.1.74.0 KVA Automatic Input 90-280 V Out put 200-240 V

SRI BIJAY KUMAR MORE

M/S N.K. CONSTRUCTION