BARC/MYS/CES/15/2023-24

Amount

Extra over initial depth for every additional Depthof 1.50 m or part there of in all kinds of soil

Extra over initial depth for every additional depth of 1.50 m or part thereof in Soft rock

Extra for every additional depth of 1.50 m or part thereof in Hard rock

Lead charges for 1st 1 KM or part thereof, by mechanical transport including loading unloading, stacking / levelling etc

Lead charges for 1st 1 KM or part thereof, by mechanical transport including loading unloading, stacking / levelling etc.

Debris up to 1 km

Supplying and injecting with approved quality chemical emulsion at the rates and concentrations as per IS 6313-2001 PartII for post Anti-termite treatment to existing buildings as per manufacturers specifications and as directed by the Engineer- in-Charge.Work to be executed by approved agency and specified guarantee for 7(Seven) years shall be furnished by the tenderer.Payment will be cleared only after submission of guarantee.

Providing and laying in position cement concrete of 1:3:6 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20 mm) including consolidation, finishing, curing etc. complete as per specificationsand drawings but excluding the cost of Form work shuttering, centering Complete at all levels

Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels

Providing and laying in position Reinforced Cement Concrete (RCC) of grade M-30 using 20mm maximum size aggregates and crushed sand of approved quality including admixtures of approved brand and quality (plasticiser or super plasticiser) if required, including weigh batching, mechanical mixing, transporting, placing, vibrating, consolidation, finishing, curing etc. complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications up to Plinth Level.

Extra for RCC all grades in super structure upto 20.00 metre height

Extra for RCC Using Ready Mix Concrete from outside project area including transporting and pumping from approved batching plants .

Providing Reinforcement Steel for reinforced cement concrete at all levels including supplying, preparation of bar bending schedules, cutting, bending, transporting, fixing, tieing in position with PVC coated G.I binding wire, all labour charges, cost of cover blocks in specified grade of concrete etc. complete as per specifications and drawings. Note:Steel supplied by the contractor

Using TMT bars of specified grades (Fe 500 or Fe 500D as directed by EIC) of all sizes. TMT bars to be supplied by the contractor as Approved by EIC

Providing Structural steel work in M.S Plain Plate sand chequrred Plates for Embedded Parts,Trench Covers, Connection plates etc. including cutting, hoisting, fixing in position and applying a priming coat of approved zinc chromate steel primer etc. including cost of structural steel Plates, welding all labour charges etc .complete as per drawings and specifications

Using materials of approved manufacturers. All test reports to be provided along with the supply of the materials and as directed by EIC

Providing, supplying, cutting, welding, fabricating, hoisting and fixing in position structural steel members like trusses, purlins, posts etc. using MS hollow / circular / square / rectangular tubular sections including appling a coat of Zinc chromate primer of approved make all as per specifications, drawings and as directed by the Engineer in charge

Fixing in position in RCC/ masonry/ form work mild steel or stainless steel fabricated embedded parts supplied by the Department including transporting from the departmental stores, aligning/ welding fixing in position, providing necessary supporting arrangement set complete all as per drawings and specifications at all levels and as directed by the Engineer in charge

Weighing Above 100 kg up to and inclusive of 1000 kg

Providing, centering, shuttering Formwork by using steel plates, timber planks for PCC and minor structures including necessary strutting, proping, without staging, supports etc and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Enginner-in-charge

Provding and constructing brick work in Cement mortar using standard bricks of approved class/ quality, make or brand in foundation and plinth including curing, raking out joints, simultaneous pointing below plinth level if specified, complete as per drawings, specifications and as directed by the Engineer-in-charge

Brick work in C.M 1:4 using crushed sand.

Providing and constructing Half brick masonry using bricks of approved quality / class, make/ brand in partition walls in C.M 1:4 (using crushed sand) including scaffolding, raking out joints, curing etc. complete and with stiffners of RCC 1:2:4 (105 X 75 mm size) at every 900 mm height including form work curing etc. complete as per specifications and as directed by the Engineer-in-charge but excluding reinforcement up to 20 m height. (Reinforcement will be paid under relevant item)

Providing and constructing Honey comb brickwork 10 / 11.4 cm thick with bricks approved quality / class in super structure in C.M 1:4 (using crushed sand) including pointing the joints complete.

Providing and Laying Solid cement concrete block masonry with M-5 Grade of 190/ 140 mm thick in super structure in cement mortar 1:4 (using crushed sand). The rate shall also include providing and placing in position 2 nos of 8 mm dia bars at every third course of the masonry work

Providing and laying size stone masonry in C.M. 1:6 in foundation and in superstructure including rough dressing and providing bond stones in each course at 2 M apart including scaffolding,curing, etc complete as per specifications and as directed by Engineer - in - charge .

Labour charges for constructing Rubble masonry using Rubble Stones available at site in super structure up to 20 m height in C.M 1:6 (using crushed sand) including cost of bond stones, raking out joints or simultaneous flush pointing below ground level / plinth level, curing etc. complete as per drawings and specifications.

Providing 12 mm thick Internal plastering in cement mortar 1:4 without cement punning (using crushed sand) finished smooth, including sieving of sand to required fineness, preparation of the surface, scaffolding, curing all as per specifications, drawings and as directed at site complete.

Providing 20 mm thick water proof plastering in cement mortar 1:3 (using crushed sand) finsihed smooth with a floating coat of neat cement including approved water proofing compound added @ 2% by weight of cement or as per manufacturer's specifications, sieving of sand to required fineness, preparation of surface, scaffolding at all heights, curing all as per specifications, drawings and as directed at site.

Providing 6 mm thick cement plastering with C. M 1:3 in concrete surfaces (using crushed sand) finished with a floating coat of neat cement for bearing of RCC beams and slabs, including hacking of concrete surfaces with a pointed tool, scaffolding, finsihing, curing etc. complete as per specifications and as directed by the Engineer in-charge

Providing FLUSH pointing on stone masonry with cement moratr 1:3 using crushed sand as per specifications and as directed at site by the Engineer-in-charge

Providing and laying (IPS Flooring) cement concrete flooring 1:2:4, using crushed sand 50 mm thick finished smooth to the required level, finishing with a floating coat of neat cement including cement slurry, providing and fixing 30 X 3 mm glass strip, curing, cleaning the surface neatly at the time of handing over the area complete as per specifications and drawings as directed by the Engineer in charge

Providing and fixing 15 mm thick flooring with acid and alkali resistant tiles of approved make and colour as per IS 4457 using acid and / or alkali resistant mortar bedding and joints filled with acid and / or alkali resisting Epoxy for 5 to 8 mm depth over a bed of Bitumastic compound 8 to 10 mm layer and bitumastic primer complete as per the direction of the Engineer-in-charge In flooring over a bed of minimum 10 mm thick acid proof mortar with acid and / or alkali resistant tiles of size 200 X 200 X 15 mm of approved colour incliding providing required slopes and levels ( this work to be carried out through approved specialized agency) complete as per specifications and as directed by the Engineer-in- charge

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS 15622 of approved make. shade and colour of size ranging from 300 - 600 mm long and 300 mm - 600 mm wide and thickness not less than 6 mm as approved by Engineer-in- charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (using crushed sand), setting the tiles in cement slurry and pointing the joints with matching colour Tile grout of approved make of matching shade including using PVC tile trim in the exposed corners, complete as per drawings, patterns and specifications complete as directed by the Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed floor tiles of minimum 300 - 600 mm long and 300 - 600 mm wide and thickness not less than 6 mm conforming to IS 15622 of approved make in all colours and shades as approved by Engineer-in- charge over a bed of 20 mm thick bed of cement mortar 1:4 (using crushed sand) and jointing with grey cement slurry including pointing with white cement based Tile grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Enginner-in-charge

Providing and fixing Glazed VITRIFIED floor tiles of approved make in different sizes conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish laid over a bed of minimum 20 mm thick bed of cement mortar 1:4 (using Crushed sand) and jointing with grey cement slurry including grouting with the joints with white cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge

Using Tiles of size 600 X 600 mm

Add Extra for polymer mortar in place of cement mortar

Providing and Fixing 3.00 mm thick Homogeneous PVC sheet / tile in flooring and skirting of aproved make in approved pattern on a smooth and damp prrof base using rubber based adhesive of approved quality and manufatrer like Dunlop-S -758, Fevicol SR 998, PolyGrip SP or equivalent including, Welding of joints, levelling small undulations with plasterof paris if required, rolling with light wooden roller weighing about 5 kg all complete as directed by Engineer-in- charge in approved colour and shade

Providing and laying Self levelling Epoxy flooring , including preparation of the surface, primer coat,screeding & levelling coat and finishing coat with Polyurethene coat of approved colour and shade of approved make all as per manufacturers specifications complete as directed at site by the Engineer-in-charge (This Job to be carried out through a specialized approved agency)

4mm thickness

Supplying, Stacking and Laying of 150 mm thick rubble soling stones as under floor base including packing with smaller stone and compacting, ramming including spreading and consolidation of blinding material, moorum etc. complete all as per specifications and as directed by the Engineer-in-charge

Providing and fixing minimum 17 mm thick gang saw cut mirror polished granite (premoulded and prepolished) machine cut ZEBRA BLACK colour granite for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edge to give high gloss finish etc. complete as directed by the Engineer-in-charge at all levels

Providing and fixing anodized aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc. (fittings glazing and panelling shall be paid for separately)

Anodised Aluminium sections (Minimum anodizing thickness of 15 micron)

Providing and fixing 12 mm thick pre-laminated particle board flat pressed 3 layer or graded wood particle board conforming to IS 12823 Grade-I, Type - II in panelling fixed in aluminium doors, windows, shutters and partition frames with C.P Brass / Stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge Prelaminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item)

With clear float glass panes of 4.0 mm thickness

With clear float glass panes of 5.0 mm thickness

Providing and fixing double action hydraulic floor spring of approved brand and manufacturer (conforming to relevant Indian Standard) for doors including cost of cutting floors as required, embedding in floors and cover plates with M.S pivot and single piece of M.S sheet outer box with slide plate etc. complete as per directions of Engineer-in-charge with brass cover plate

Providing and fixing in position suspended seamless false ceiling system using 12.50 mm thick moisture resistant plain gypsum board ( GYPROC.MR of M/s .Saint Gobain make) suspended ceiling, which includes Gypsteel ULTRA™ CRP surface ribbed perimeter channels (having one flange of 20mm and another flange of 30mm and a web of 27mm) along the perimeter of ceiling, screw fixed to brick wall/partition with the help of nylon sleeves and screws, at 610mm centres. Then suspending Gypsteel ULTRA™ CRP surface ribbed intermediate channels of size 45mm (with two flanges of 15mm each) from the soffit at 1220mm centres with Gypsteel ULTRA™ CRP surface ribbed ceiling angle of width 25mmx10mm fixed to soffit with GI cleat and steel expansion fasteners (Mfg by Ms Saint Gobain Gyproc).

Gypsteel ULTRA™ CRP surface ribbed Ceiling section of having web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the Gypsteel ULTRA™ intermediate channel with the help of connecting clip and in direction perpendicular to the Gypsteel intermediate™ channel at 457.5mm centres. Single layer of 12.5mm tapered edge Gyproc® MR (conforming to BS 1230 part 1) is then screw fixed to ceiling section with 25mm drywall screws at 230mm centres. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Gyproc jointing compound, Gyproc joint paper tape and two coats of drywall top coat (as per recommended practices of M/s Saint- Gobain Gyproc India

Providing and fixing cup board shelves using 25 mm thick pre- laminated flat prssed 3 layer (medium density) particle board or graded wood particle board in shelves including 18 mm x 20 mm teak wood beadings at all sides with necessary screws and fittings all as per drawings and specifications and as directed by Engineer- in-charge

Demolishing C.C / R.C.C works by mechanical means and stock piling at designated locations carefully with out damaging adjacent structures and disposal of dismantled materials up to a lead of 100 m, stacking serviceable and unserviceable materials separately including cutting reinforcement bars all as directed at site

Dismantling brick work in Cement mortar carefully without damaging adjacent structures including stacking of materials and dispoal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

Demolishing Stone rubble masonry (In cement mortar) manually / by mechanical means carefully without damaging adjacent structures including stacking of serviceable materials and disposal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismantling and stacking within 100 m lead

Dismantling roofing including ridges, valleys and gutter etc and stacking the material within 50 m lead

G.S Sheet / FRP Sheet / AC Sheet

Dismantling barbed wire / flexible wire rope in fencing including making rolls and stacking within 100 m lead

Dismantling Aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplaus material and stacking of serviceable materials within 100 m lead as directed by the Engineer-in-charge

Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-30 grade made with strong vibratory compaction and approved size, shape, design laid in required colour and pattern over and including 50 mm thick compacted bed of crushed sand, filling the joints with crushed sand etc. all complete as -per the direction of the Engineer-in-charge

Providing and fixing dry stone pitching 22.5 cm thick laid in required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete as directed by the Engineer-in- charge

Providing and fixing GI chain link fabric fencing Made of GI wire of dia 4 mm of required width in mesh size 50 x 50 mm including strengthening with 2mm dia wire or nuts, bolts and washers as requeid complete as per direction of Engineer-in-charge.

Fixing of wire fabric chain link fencing of 50 mm x50mmx 4 mm thick to existing angle post including strengthing with 3mm dia wire at top & bottom, providing & fixing 07 no. of nuts & bolts, 6 mm vertical bar at every angle post & washers, making holes to the angles etc as required to complete the work as per specifications, drawing & the direction of the EIC. Note: Chain link shall be provided as a free issue material to the contractor, Rate shall be inclusive of shifting of chian link from RMP store to the site.

Fencing with RCC post placed at required distance, embedded in cement concrete blocks every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire 9.38 kg per 100 metres (min) between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post etc. complete as directed by the Engineer-in-charge. (cost of RCC posts, struts, earth work and concrete to be paid for separetely) : Payment to be made per metre cost of total length of barbed wire used

With G.I. barbed wire 12 swg

Providing and fixing concertina barbed tape coil of follwoing dia. made from M.S galvanized ribbon tape of 0.5 mm thickness, 19 mm width stretching the coil to 9 m approximate, fixing the coil with clips between "Y" armed and MS angle posts 2.44 m high from ground level, including supplying and fixing MS galvanized clips etc. complete as per manufacturer's specification and including painting by dipping method the concrtina tape coil with two coats of synthetic enamel paint of approved shade and make over a coat of approved primer at fabrication shop, before bringing the material to the site and fixing in position etc. complete as directed by the Engineer-in-charge

450 mm Dia Concertina coils

Providing and fixing precoated Galvalume Roofing profile sheets of approved size, shape and pitch up to and including single length of 12.00 met. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 X 55 mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers filled with white lead complete upto any pitch in horizontal / vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required as directed by the Engineer-in- charge

Galvalume sheet roofing 0.50 mm Thickness in Single sheet

Providing and fixing precoated Galvalume roofing accessories using self drilling / self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete.

Roofing accessories of Galvalume sheet up to 600 mm total width for ridges, gutters, aprons,and flashings

Providing and repairing to internal plaster in cement mortar 1:4 (using crushed sand) of thickness 12 mm to 20 mm in patches of area up to 2.5 sq metres including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls, including disposal of rubbish to the dumping ground within 50 metres lead

Making the opening in brick masonry for door / window / clear story opening including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete to match existing surface including disposal of mulba/ rubbish to the nearest dumping ground

Providing and Fixing Anchor Fastner of approved make including drilling in concrete as per requirement for fixing Eps or other structures all as specified by the manufacturer complete all as per specifications and drawings

16 mm diameter 100 mm Long

Providing and laying non pressure NP2 class RCC Hume pipes of approved make, with collars jointed with stiff mixture of cement mortar in the proportion of 1:2, laying to the levels, slopes and as per the drawings and specifications and as directed by the Engineer-in-charge including testing of joints etc. complete.

300 mm Dia RCC Hume pipe class Np2

Supplying of UPVC pipes for rain water system (Type- A pipes) , soil and waste discharge system (Type-B pipes) of maximum thickness in accordance to IS : 13592 and laying below ground including jointing with sockets using solvent cement in accordance to IS : 7634 (Part 3 - 2003), with all necessary fittings such as bends, tees, elbows, reducers, unions, nipples, plugs etc., nclusive of excavation in soil, removal of sharp objects / stones etc., testing for water tightness, anchoring, if required with concrete anchor blocks of 1:2:2 proportion, backfilling with suitably good soil in layers of 75mm, watering, compacting, placing of marker plates to show location etc. complete as per drawings, specification and direction of the Engineer-in-Charge. Note : Payment for excavation and backfilling shall be paid in the respective item.

Type A Pipes - 160 mm dia

Type B Pipes - 160 mm dia

Supplying and laying UPVC pipes for rain water system (Type-A pipes), soil and waste discharge system (Type- B pipes) of maximum thickness in accordance to IS : 13592, laid over ground on walls/floors with straps / clamps at 1.00 m spacing, jointing with sockets using solvent cement as per IS : 7634 (Part 3 - 2003), with all necessary fittings such as bends, tees, elbows, reducers, unions, nipples, plugs etc. testing for water tightness complete as per drawings, specification and irection of the Engineer-in-Charge.

Type A Pipes - 110 mm dia

Type B Pipes - 110 mm dia

Welding work for Steel doors, windows frame, shutters , pipe joint etc. Like welding, grinding or cutting work with available materials etc complete as directed by Engineer in Charge.(Note. Required tools, machinary shall be arranged by the ontractor) Note: One operation means welding of pipes upto 200mm weld length at one location or welding of one hinge/ one MS joint in case of door & window including cutting & grinding Note: In case of any emergnecy contractor has to arrange the welding work immediately (24x7) after the instructions given by EIC.

Lifting and lowering of the bore well pump along with GI Pipes to a depth Ranging from 200- 300 feet below the ground level. The work includes lifting and lowering including all tools, men and materials, handover pump to electrical/mechnical section after repairing its lowering etc complete as per direction of Engineer in Charge

Fabrication and fixing in position in concrete/brickwork etc all the structural steel items like m.s.plates, m.s.angles,m.s.rounds, m.s.flats, m.s.square bars m.s.bolt/nuts with washers, etc at all lifts as per specifications and instructions of Engineer in charge complete with two coats of synthetic enamal painting over one coat of redoxide primer etc complete. Note: Structural steel Items/ sections will be supplied by the department as a free issue material and the rest all i.e transporation ,bolts, welding, required consumables with painting are included in the rate

Providing and injecting HYDROPHOBIC POLYURATHANE (PU) grout of approved manufactures using 12mm dia galvanised steel injection nipple at Construction joint or structural cracks or any other leakage place including drilling of holes of required diameter (12mm to 20mm) up to depth from 30mm to 50mm with injection pump. The PU materials shall be injected through the prefixed NRV packers under pressure using mechanical grout pump of minimum 40 PSI pressure to fill all possible pores and gaps left within the concrete mass. The injection shall start at the widest section of a horizontal crack. Vertical cracks are typically injected from the bottom to up. The mechanical packers shall be removed after 24 hoursand the gaps filled with PU resin mortar including all lifts, leads, scaffolding etc complete as per direction of Engineer in Charge.

Providing helping assistance for Operation and maintenance of Civil works including plumbing, carpentry and masonry works in BARC Plant site and BARC Residential township at Yelwal, Kuvempunagar and Lakshmipuram. The nature of works includes getting complaints from civil section daily, Attending the complaint by helping departmental technicians as soon as possible. Update the register after completion of daily complaints or Any civil works assigned by departmental engineers Note: The labours is working for full eight hours and maintain regular attendance register in case any short fall / absentee payment will be made on prorata basis. Note: Two labours/helper shall be provided daily

Assisting Works

Supplying and fixing 10 gauge weld mesh with aperture size of 25 X 25 mm weld properly over the existing safety grill for sliding windows/openings etc, including scaffolding at all lead, lift and levels etc complete as directed by the Engineer-in-Charge.

E. P.RAVI, CIVIL WORKS CONTRACTOR