CONSTR OF TCP WITH TOILET AT MAIN GATE OF DIV HQ, SPL REPAIRS TO SECURITY FENCE AROUND KOTE OF 264 FD WKSP COY EME, DRAINAGE SYSTEM OF JCOS OR MD ACCN NEAR BLDG NO. P 51, 52, 53 AND P 57 AND REV WK NO. 13 PROVN OF HARD STANDING OUTSIDE CSD CANTEEN

Amount

STN/LBW/06/2019-20 Constr of TCP with toilet at main gate of Div HQ at Umroi MIL STN Under GE Umroi

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose Soil complete all as specified and directed

Excavation in trenches n. exc. 1.5 m wide and n.exc 1.5 m in depth for foundation or for shaft, well, cesspit, manhole, pier hole etc.n. exc. 10 sq m on plan and n. exc. 1.5 m in depth and getting out in any type of soil complete all as specified and directed.

Material and labour for plain Cement concrete Type D2, 1:4:8 mix, (40 mm graded aggregate) in foundations, filling and mass- concrete complete all as specified and directed.

Material & labour for 40mmthick Damp proof course to horizontal or vertical including necessary formwork in cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone agg) and applying evenly a coat of blown type bitumen @ 1.5 Kg per sqm and binding with dry sand @ 0.5 Cum per sqm complete all as specified and directed.

Material & Labour for Pre-cast cement concrete block masonry with solid blocks, exceeding 10 cm in width and setting mortar, complete With C1 Type, 1:3:6 mix, (20 mm graded aggregate) set in cement mortar 1:6 Complete all as specified & directed

Material and labour for reinforced cement concrete (nominal mix) B1 type, 1:2:4 mix (using 20 mm graded aggregate) in foundation & including rafts, footings, foundation beams, plinth beams, bases for columns, basment slabs, under -reamed piles complete all as specified and directed.

Material and labour for Reinforced cement concrete (nominal mix) B1 type, 1:2:4 mixusing 20mm graded aggrerate as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Material and labour for Reinforced cement concrete (nominal mix) B1 type, 1:2:4 mix using 20mm graded aggrerate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Material and labour for Reinforced cement concrete (nominal mix) B1 type, 1:2:4 mix using 20mm graded aggrerate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use & waste for Formwork rough finished to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

Use & waste for Formwork rough finished to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

Use & waste of Formwork rough finished to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, also splays between floors and beams, complete all as specified and directed.

Use and waste of Formwork rough finished to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)complete all as specified and directed.

Supply & Fix TMT bars 10mm dia and above cut to length bent to shape required including cranking, bending spirally for hooping, hooling ends and binding with mild steel wire (annealed) not less than 0.9mm dia , complete all as specified and as directed.

All as per Sr. Item No. 1.14 here in above but 6 mm to 8mm dia of bar.

All as per Sr. Item No. 1.14 here in above but 5 mm dia and over upto and including 10mm dia as in stirrups, spacers and binders.

Material & Labour for Pre-cast cement concrete block masonry with solid blocks, not exceeding 10 cm in width and setting mortar, complete With C1 Type, 1:3:6 mix, (20 mm graded aggregate) set in cement mortar 1:4 Complete all as specified & directed

Material & Labour for rendering 15mm thick in cement mortar 1:4 on fair faces of brick wall or on concrete surfaces shall be done in two layers, 1st layer shall be of 10mm thick and 5mm thick 2nd layer mixed with water proofing compound @ 3% by weight of cement finishing the surfaces with fair and even without using extra cement complete all as specified and directed. Note: Integral water proofing compound shall be paid and measured separately.

Supply only integral water proofing compound ISI marked.

Material & Labour for Rendering 10mm thick in CM 1:6 on surface of brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material & Labour for Rendering 5mm thick in CM 1:3 concrete ceiling surfaces, rendering is to be finished even and smooth without using extra cement complete all as specified and directed.

Material & Labour for roughening surface of concrete roof by picking, sweeping clean and washing down with water to remove dust, etc and applying roof treatment with the following specifications:- (a) Applying cement slurry over concrete surfaces @3kg/sqm. (b) Rendering 15mm thick in cement mortar (1:4) mixed with water proofing compound as per manufactures instruction on cleaned concrete surfaces of roof and finishing the surfaces fair and even including curing the plastered surfaces for 7 days by ponding of water over the roof, (levelling course). (c) Applying evenly one coat of cold bituminous primer conforming to [email protected] litre per square metre on the cleaned plastered surfaces (d) Applying evenly one coat of blown hot bitumen of grade 85/25@ 1.20 Kg per square metre on primed surfaces. (e) Applying a layer of APP based polymeric membrane, 3mm thick (minimum) weighing 3.50 Kg per square metre reinforced) with polyester non woven fabric weighing not less than 160 gms per square metre by torch application. The overlap shall not to be less than 100mm on transverse direction and 75mm on longitudinal direction and sealing overlaps. (f) Applying evenly one coat of aluminium paint @ 0.10 litre per square metre over the APP based polymeric membrane.

Material & Labour for preparation of new surfaces of wall and applying two coats of distempering with distemper oil emulsion over a coat of alkali resistant primer complete all as specified and directed.

Material & Labour for Three coats of white wash including preperation of newly plastered ceiling surface complete all as specified and directed.

Material & Labour for hardcore of brocken stone gauge n,exc 63mm deposited spreed and leveled in layers n. exc. 15cm thick water and rammed to true surfaces complete all as specified and directed.

Material & Labour for 100 mm thick cement concrete 1:4:8 type D2 using 40 mm graded aggregate as in sub base complete all as specified and directed.

Material & Labour for 75 mm thick cement concrete type C2, 1:3:6, using 40 mm graded aggregate as in plinth protection, finishing cement concrete surface even and smooth without using extra cement including making proper joints with bitumen mastic with sand as per specification at an interval of 3m complete all as specified and directed.

Material & Labour for 15 mm thick Screed bed or bedding layer of cement mortar 1:6, laying for floor finishes complete all as specified and directed.

Material & Labour backing coat of cement mortar (1:4),10 mm thick for vertical surfaces such as skirting and dado complete all as specified and directed.

Supply & Fix Non - skid Ceramic colour tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Supply & Fix Glazed ceramic tiles in vertical surface 350x250x 7 mm/450 x 350x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

Supply & Fix Non - skid Ceramic colour tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Supply & fix for Powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for door/windows and ventilator/ partition with one or more rebates including necessary joining cleats for fixing complete all as specified and as directed.

Supply & fix for Powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium track shutters of windows and ventilator with one or more rebates including necessary joining cleats for fixing etc. fixed or sliding type/ louvered window or ventilator without sash bar aluminium including joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws anodised aluminium fittings with locking arrangement complete all as specified and as directed.

Supply & fix for Powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, ruler neoprene packing, anodised aluminium snap beading screws complete all as specified and as directed.

Supply & fix aluminium anodised grill of design DG 104 pattern made out of 10mm dia rod, fixed with and including standard aluminium frame of F section of size 23.4mm x 15.3mm x 1.4mm thick all as per manufacturers instructions complete all as specified and directed.

Material & labour Prelaminated particle board 12mm thick, exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

Supply and fix 3mm thick figured glass, pin headed type and glazing with oil putty or aluminium glazing clip in square n exc 0.5 sq. m in each complete all as specified and directed.

Supply & Fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, fixing in opening complete all as specified and directed.

Supply & fix Factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles) with particle board with 2,4 or 6 raised panel design with 2 mm thick 3D wood grain moulded PVC sheet Polyurethane paintedonthe front face and 2 mm prelam PVC sheet on back face in frame at site as specified and directed.

Supply and fix aluminum anodised barrel tower bolt ISI marked 150mm long of extructed section all as specified and as directed.

Supply and fix aluminum anodised handle cast type ISI marked 125 mm, anodised all as specified and as directed.

Supply and fix butt hinges 100 mm long extruded aluminium alloy ISI marked with galvanised mild steel hing pin type B-21 as specified and as directed.

Supply & Fix Wash basins, Vitreous China (flat back or angle back type) of size 550 x 400 mm, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

Supply and fix Pillar taps of 15mm , cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe.

Supply & Fix Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

Supply & Fix Toilet paper holder of brass chromium plated fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

Supply & Fix PTMT tubular Towel Rail 600mm long and 20 mm dia fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as directed.

Supply & Fix Shelf of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and directed.

Supply & Fix 10ltr capacity Low level PVC valveless, syphonic action type fluslhing cistern, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

Supply & Fix Flush pipes of PVC. 32 mm dia connected to pedestal pan, including all joints pipe of polyethylene of low or high density for low level cistern complete all as specified and directed.

Supply & Fix CP Bib taps 15mm, fancy type, cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply & Fix CP Stop valves 15mm, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions.

Supply & Fix PVC connection 15 MM size with PTMT nuts of length 600MM complete all as specified and directed.

Supply & Fixing steel Tubes medium grade(ISI marked), 20mm bore galvanised with all fittings and fixed complete to wall and ceiling or laid in floors Complete all as specified and directed.

Supply & Fixing steel Tubes medium grade (ISI marked), 15mm bore galvanised with all fittings and fixed complete to wall and ceiling or laid in floors Complete all as specified and directed.

Supply & Fix 500 ltr Rotational moulded polyethylene water storage tanks ISI marked (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed.

Supply & Fix Ball brass valves (ISI marked) of 20 mm bore, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as directed.

Supply & Fix Gun-metal, globe or gate valves (ISI Marked) for iron pipe 20mm bore with iron wheel head, screwed both ends complete all as specified and directed.

Supply & Fix PVC (SWR) pipes ISI Marked 110mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Supply & Fix PVC (SWR) bends ISI marked 110 mm bore any radius complete all as specified and directed.

Supply & Fix PVC P trap, 125/110 mm bore (ISI Marked) complete all as directed.

Supply & Fix PVC (SWR) vent cowl ISI Marked 110mm bore complete all as directed.

Supply & fix 40 mm Low Density Polyethylene pipes (LDPE) of pressure rating 6 Kgf/Cm2 fixed complete to wall ceiling or in floors complete all as specified and as directed.

Supply & Fix grating square 150mm size PTMT (Min weight 100gms), complete all as directed.

Material & Labour for preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n. exc. 25cm thick in any type of soil, all as specified and directed

Removing excavated soil not exc 50m and depositing where directed at level not exc 1.5m above the starting point complete all as specified and directed.

Material and labour for plain cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate for foundation filling and mass concrete all as specified and directed.

Material & Labour Cement concrete 1:2:4, type B0, using 12.50mm graded crushed stone aggregate in coping, benching, haunching, kerbs water troughs, platform over roof slab for instalation of PVC water tank and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified as directed.

Material & Labour precast RCC 1:2:4, type B1 using 20mm graded aggregate as in drain cover slab supported on walls, desk slabs and shelves including necessary formwork, complete all as specified as directed.

Material & Labour for 150mm bore, reinforced concrete pipes, class NP2, laid and jointed complete with collars, complete all as specified and directed.

Material & Labour Concrete 1:3:6 (40mm graded aggregate) as in bed to drain pipes 150mm bore (dia) including packing under, and haunching against the sides of pipes after they are laid and tested; complete all as specified and as directed.

Material and labour for Construction of septic tank of capacity 10 users single chamber including inlet and outlet chamber old solid concrete block masnory including RCC slab, excavation in soft/loose soil, returning/filling in, removal of surplus soil etc complete all as specified and shown on drawings and as directed as shown in TD and PS clause no. 16. Refer TD. No.TD/SZ/504, sheet No. 1/1

Material & Labour for construction of soakage wells 1.2m dia and 3m deep with solid concrete block in PCC 1:3:6 wall with honey combing including excavation in soft/loose soil, returning filling in, removal of surplus soil to a distance n exc.50m, RCC slab complete all as specified and directed and as shown in TD and PS clause no. 17. Refer TD. No. TD/SZ/502 sheet No. 1/1

Excavation over areas, n exc. 1.5 m deep and getting out in any type of soil for foundation and getting out complete all as specified and directed.

Material & Labour for walling random rubble uncoursed well bonded, bedded and solidly hearted built in CM (1:6) complete all as specified and directed.

Material & Labour for precast cement concrete type C1 ( 1:3:6, using 20mm graded crushed stone aggregates) as in bond stones set in cement mortar 1:6 complete all as specified and as directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints as specified of random rubble walling uncoursed or brought upto courses in hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc. 40 mm of lime or sand stone complete all as specified and directed

Material & Labour for raised pointing to random rubble masonary uncoursed or brought upto courses in CM 1:4 complete all as specified and directed.

Material & Labour for loose filling with broken stone aggregate of gauge exc 40mm but not exc 80mm deposited to shape complete all asspecified and directed.

Supply and fix in repairs of MCB TPN DB 4 way for mounting SPN/SP/TPN/TP MCBs as incoming/outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DB shall be semi glossy finished with epoxy polyster based powder paint sprayed and backed at high temperature between powder paint process the steel sheet have to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43-IK 09 with metal door complete all as specified and directed.

Supply & fixing MCB SP 6 to 32 Amps 'B' Series 10 KA, 240 volts complete all as specified and directed.

Supply & fixing MCB SPN 40 Amps 'B' Series 10 KA, 240 volts complete all as specified and directed.

Material & Labour for sand cushioning to under ground cable using locally available fine clean dry river sand over,under ground UG cable laid in treches and gently punning to cushioning to cable complete all as directed. Note: Thickness of sand cushion after punning down will be measured and paid.

Material & Labour for common burnt clay building bricks (locally available best quality), sub-class ‘B’ designation 75 of size 230x150x40 mm to cover LT underground cables , laid dry and flat abutting each other with gaps not exceeding 10mm complete all as specified and directed.

Supply, laying connecting and testing XLPE insulated, PVC sheathed, armoured LT electric power UG cable (heavy duty) of size 10 sqmm 2 core, aluminium stranded conductor 1100 volts grade, laid through duct/ pipe / in trench etc. including cable glands & lugs complete all as specified and directed.

Supply and install lithium based Energy efficient integrated Solar Street light 30/32 watt including MS Pole(Outer Dia 60 mm) 6m high (above ground) duly painted with two coats of white aluminium paint along with one coat of primer including Single body encases Solar PV Panel 64/66 Wp monocrystalline capacity > 60 W, Lithium based battery 11.1/12,8V, >21.0 AH with inbuilt BMS, High brightness W-LED(>120 lm/watt) lamp with reflector, CRI > 70, colour temperature 6500K, microcontroller based charge controller cum driver, automatic dimming function with PIR motion sensor, Dusk to down operation, working temperature (-) 10 C to (+) 55 C, with adjustable MS Clamp suitable for pole/wall mounting. lights and panel shall have Protections against short circuit, over load, reverse polarity and battery protection. Pole shall be fixed in PCC 1:3:6 as in foundation of size 0.70m down fixed with plate of 0.30 x 0.30 m x 4mm and coping of height 0.20m above ground shall be done with PCC 1:2:4. Quoted rate shall be inclusive of earthwork and excavation. The pole below the ground shall be painted with one layer of bituministic paint. Make; LHSTAKU7CBAF030 of Havells and BSZSL 30W LED of Bajaj and HLSSLINTO201070410-30W-WOPCWL of Halonix and equivalent in ISI marked make

Supply, install , testing and commissioning of electronic boom barrier of boom size 6 m long with 1 controller, 1 remote control, 1 push button, 1 boom rest and specification as per Clause no. 15 of PS and foundation frame, warning light, safety photo cell, operation on single phase AC supply, weather proof body, complete all as specified and directed. NOTE:- 1. The excavation and earthwork of foundation shall be mesaured and paid seperately. 2. The foundation shall be made of RCC (1:2:4)(Nominal Mix) with 20 mm graded stone and its connected items shall be measured and paid seperately.

Supply and laying of CAT 6 cable, ISI marked for electronic boom barrier complete all as specified and directed.

Material and labour point wiring for light/fan with 1.5 Sqmm single core, PVC FRLS insulated unsheathed, multistranded copper conductor drawn through and including PVC concealed conduit including necessary accessories like bends, tees PVC square box and elbow etc fixed on wall/ceiling with 1.5 Sqmm PVC FRLS insulated unsheathed stranded copper conductor cable as earth conitinuity (green in colour) connected to common earth dolly including sunken type pressed steel terminal boxes of suitable sizes painted with black bituminous paint outer side and aluminium paint inner side, with plastic laminated white/coloured top sheet cover 3 mm thick complete all as specified and directed

All as per Sr Item No.2.10 Here in above but for 5 Amp socket on independent board

All as per Sr Item No. 2.10 Here in above but for 3 pin 15 Amp socket point fixed with 2.5 Sqmm PVC FRLS insulated copper conductor cable

Supply and fixing of switch piano flush type ISI marked 240 Volts 5 Amps, SP, one way complete all as specifed and directed.

Supply and fixing of switch socket outlet 3 Pin, 5 Amps, 240 volts flush type (non shuttered) ISI marked complete all as specified/ directed.

Supply and fixing switch socket out let combination multipurpose 5 pin, 15/16 Amps and (with 3 pin 5 Amps outlet also) flush type (non shuttered) ISI marked complete all as specified/directed.

Supply & fixing ceiling fan regulator electronic ISI marked, Deluxe, rotary, step type, 120/280 V complete all as specified and directed.

Supply & fix non decorative ceiling fans white in colour with complete accessories of BEE 5 star rating 230 V,1200 mm sweep alongwith iron rod and suitable nut bolts for hanging of fan from ceiling including fan regulator complete all as specified and directed. Make :Havells/ Bajaj/ CG / Khaitan or its equivalent in specified make.

Supply and fixing ceiling rose surface PVC/Polycarbonate ISI marked, 65x50 mm two to three terminals complete all as specified and directed.

Supply and fixing LED fitting 1x18 watts including Tube rod, 230 Volts, bipin holders connector block etc.complete with all accessories internally pre-wired and including provision of PVC round block 7.5cm dia and 2 cm in depth (2 Nos) for mounting the fittings and electrically connecting with three single core 23x0.0076 PVC insulated multistranded copper conductor flexible cable from ceiling rose to light fitting, complete all as specified and directed. Make: : Bajaj Cat Part No BLRB- DB 118 for batten and Bajaj Tube rod No BLRB-18 Watt CWc or equivalent in specified make

Material & labour for Sub main wiring with two runs of single core 6 Sqmm (Nominal Area) FRLS PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC casing capping of adequate size fixed on surfafce of wall/ceiling with all necessary fittings and accessaries and 1 run of FRLS PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 4 Sqmm as earth wire (green in colour) run through casing capping and connected common earth dolly including taking out the old sub main wiring connection to DBs/dolly shall be deemed to be included in this item and two run of 6sqmm as current carrying conductor and one run of 4 sqmm as earth conductor and PVC casing & caping shall be measured as one run complete all as specified and directed.

Supply and fix exhaust fans AC single phase 230/240 V of size 300 mm sweep plastic body with louver complete all as specified and directed. Note: Quoted rate shall be deemed to be included of other accessories required for fixing and making good disturbed surfaces.

Supply & Fixing steel Tubes medium grade, 25mm bore galvanised with all fittings and fixed complete to wall and ceiling or laid in floors Complete all as specified and directed.

Supply & Fix CP Stop valves 25mm, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions.

UMR/STN/REV/13/2019-20 Provn of hard standing outside CSD canteen of INF BN II at Umroi MIL STN

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose Soil complete all as specified and directed

Material & Labour for hardcore of brocken stone gauge n,exc 63mm deposited spreed and leveled in layers n. exc. 15cm thick water and rammed to true surfaces complete all as specified and directed.

Material & Labour for 100 mm thick cement concrete 1:4:8 type D2 using 40 mm graded aggregate as in sub base complete all as specified and directed.

Material & Labour for 75 mm thick cement concrete 1:2:4 type B2 using 40 mm graded aggregate as in flooring sub-base complete all as specified and directed.

Material & Labour Cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate in coping, benching, haunching, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified as directed.

Material and labour for formwork to faces of walls, retaining walls, abutments, parapets and similar work including attached pillasters, buttresses, etc; vertical or batter for fair finished surfaces, complete all as specified and directed.

Material & Labour for Forming 12mm thick expansion joint 100mm deep, feilled with preformed bituminous filler and top 30mm primed and sealed with sealing compound grade A complete all as specified and directed

STN/SR BLDG/UMR/15/2019-20 (SPL REPAIRS TO SECURITY FENCE AROUND KOTE OF 264 FD WKSP COY EME) & STN/SR BLDG/UMR/13/2019-20 (SPL REPAIRS TO DRAINAGE SYS OF JCOS/OR MD ACCN NEAR BLDG No. P-51, P-52, P-53 & P-57)

Dismantling posts or struts (wood, steel or R.C.C) any section, including taking out embeded portionand making good disturbed ground Posts embedded in Natural ground complete all as specified and directed.

Dismantling fencing wire mesh, any type and removed from site complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss and removed from site complete all as specified and directed.

Dismantaling wrought iron or mild steel work of any description not otherwise provided for and removed from site complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position etc complete all as specified and as directed.

Excavation in trenches n. exc. 1.5 m wide and n.exc 1.5 m in depth for foundation or for shaft, well, cesspit, manhole, pier hole etc.n. exc. 10 sq m on plan and n. exc. 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

Excavation in post holes(or similar holes) in soft/loose soil each n exc 0.5 cu.m,getting out ,returning ,filling in and ramming earth or broken rubble mixed with earth around,in layers not exceeding 25 cm watering and removing surplus soil to a distance not exceeding 50m and making good complete all as specified and directed.

Material and labour for plain Cement concrete Type D2, 1:4:8 mix, (40 mm graded aggregate) in foundations, filling and mass- concrete complete all as specified and directed.

Material and labour for plain cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate for foundation filling and mass concrete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete (Nominal Mix) M-25 using 20mm graded aggrerate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Material and labour for Reinforced cement concrete (Nominal Mix) M-25 using 20mm graded aggrerate as in Columns, pillars, piers, posts and struts complete all as specified and directed.

Material & Labour Cement concrete 1:2:4, type B0, using 12.50mm graded crushed stone aggregate in coping, benching, haunching, kerbs water troughs, platform over roof slab for instalation of PVC water tank and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified as directed.

Use & Waste of Formwork rough finished to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

Use & Waste of Formwork rough finished to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

Supply fabricate , fixing structural rolled mild steel Fe - 410-W (Gde-E-250) quality "B" joints, channel, angle, tee sections fixed independently without connecting plates (cut to ordinary lengths i.e. within 20 mm of the length indicated ) , inclusive of one primer coat and two coats of aluminium paint after preparation of surfaces complete all as specified and directed .

Supplied & Fixed mild steel conforming to Fe-290 Gde-E-165 Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required ; hooks (stay), heavy, for large gates ; hook and pintle hinges ; large hasps and staples ; chains ; hand made slinding bolts; clamps ; hold fasts ; wall ties hooks forhanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles complete all as specified and directed

Material & Labour for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (inclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410-W(Gde E-250) quailty A all as specified and as directed.

Supply & Fix TMT bars 10mm dia and above cut to length bent to shape required including cranking, bending spirally for hooping, hooling ends and binding with mild steel wire (annealed) not less than 0.9mm dia , complete all as specified and as directed.

All as per Sr. Item No. 18 here in above but 5 mm dia and over upto and including 10mm dia as in stirrups, spacers and binders.

Material & Labour for Rendering 5mm thick in CM 1:4 on of block masonry or concrete surfaces complete all as specified and directed.

Supply and fix hard drawn PVC coated MS galvanised steel wire chain link fencing of wire mesh nominal pitch of wire not exc 100mm, plain wire, dia of each wire each way exc 2.5mm including line wires, with standard rails, straining bolts, including provision of binding wire complete all as specified and directed.

Supply & Fix Galvanised, 2 strand, steel barbed wire, barbed with 2.24 mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

Material & labour for Mild steel round bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Supply and fix 16mm dia of neck Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square not exc 5cm long complete all as specified and directed.

Material & Labour applying two coats of synthetic enamel paint over a coat of red oxide primer on new or previously untreated steel surface of girth exc 10cm width or girth complete all as specified and as directed.

Material & Labour applying two coats of synthetic enamel paint over a coat of red oxide primer on new or previously untreated steel surface of girth not exc 10cm width or girth complete all as specified and as directed.

Material & Labour for preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of alkali resistant priming paint complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n. exc. 25cm thick in any type of soil, all as specified and directed

Removing excavated soil not exc 50m and depositing where directed at level not exc 1.5m above the starting point complete all as specified and directed.

Demolition of cement Concrete (unreinforced) in any position and of any size complete all as specified and directed

Material and labour for PCC 1:2:4 Type B2 (using 40mm graded aggregate), as in surface channels and drains, complete all as specified and as directed.

Material & Labour for PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in side wall channel and drain complete all as specified and as directed.

Material and labour for formwork to faces of walls, retaining walls, abutments, parapets and similar work including attachedpillasters, buttresses, etc; vertical or batter for fair finished surfaces, complete all as specified and directed.

Material & Labour extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds,mitered/stoped ends complete all as specified and as directed.

Material & Labour Add or deduct for each 25mm girth or part thereof over or under 30cm inner girth in cement concrete ,using extra cement,including forms, moulds,mitred/stopped ends complete all as specified and as directed.

Material & Labour for Rendering 15mm thick in CM 1:6 on surface of block work, rendering is to be finished even and smooth without using extra cement complete all as specified and directed.

Material & Labour precast RCC 1:2:4, type B1 using 20mm graded aggregate as in drain cover slab supported on walls, desk slabs and shelves including necessary formwork, complete all as specified as directed.

Material & Labour for 75 mm thick cement concrete type C2, 1:3:6, using 40 mm graded aggregate as in plinth protection, finishing cement concrete surface even and smooth without using extra cement including making proper joints with bitumen mastic with sand as per specification at an interval of 3m complete all as specified and directed.

S K TRADERS