Development of small pond and surroundings area adjacent to SJVV near Junior College at Anushaktinagar, Mumbai

Amount

ABSTRACT SHEET

PART I- CIVIL WORK

Description of Work / Item(s)

Amount

PART I - CIVIL WORK

Desilting by mechanical excavation, Drying the silt at site, disposing off silt from pond bed, levelling at the bed level of pond, near Junior college, over all areas and at all levels, in all soils including soft rock by mechanical means upto following depth below the existing bed level/ silt top level, grade,camber, dressing the sides, trimming ramming and making the bed levelled including Dewatering, dressing of excavated area and disposing the surplus excavated materials outside the Anushaktinagar, etc. complete all as per specification and directed by the Engineer-In-Charge.

a) upto 1.5 m depth from silt top level

b) 1.5 m to 3.00m depth from silt top level

Earth work excavation in all areas in following by mechanical means /manual means upto 1.50 m deep to required profile, level, grade, camber, dressing the sides, trimming, ramming and preparing the bed for foundation including dewatering, shoring (side supports trenches) dressing of excavated area and refilling in layers , consolidating the back filled soil etc, disposing the surplus excavated materials at the designated place within the colony etc. complete all as per specification and directed by the Engineer-In-Charge.

a ) From 0.00 to 1.50 m depth from Average Ground level in all soils and soft/ Hard Murum

a ) From 0.00 to 1.50 m depth from Average Ground level in Hard rock

Providing and laying dry rubble stone hard core soling of 230/150mm consolidated thickness in sub base to required levels and lines with first quality rubble, hand set, well packed including filling the interstices with smaller stone chips, supplying & finishing/blinding the surfaces with approved blinding quality murrum/ stone dust including watering, rolling the sub-base with 8 to 10 ton roller at optimum moisture content and again rolling the rubble soling , consolidation etc. all complete as per specification drawings & as directed by EIC.

Random rubble masonry at all heights and levels using spotless black trap or approved locally available stone in cement mortar 1:6 including Dewatering, raking out joints, simultaneously flush pointing using through bond stones at every 900 mm in horizontal & vertical courses of each layer, curing etc. complete all as per specifications, directed by the Engineer-in-Charge.

a) Rubble stone supplied by contractor

Providing and fixing Hydraulically pressed factory made kerb stones full bull nose /battered from approved manufacturers like M/s Super Tiles or other approved equivalent , made up of cement concrete grade not less than M-30 and having size 500 X 325 X 125 mm , of approved including necessary form work, compaction, finishing, curing, fixing with CM 1:3, jointing and pointing in cement mortar 1:3 including earth work and 75 mm thick & 200 mm wide PCC 1:3:6 for foundation below kerb stone etc. complete all as per specification and as directed by the Engineer in charge

Labour charges for removing and relaying existing 60/80mm interlocking paver blocks/ Shabad tile including supplying & laying 50 mm thick well graded stone dust evenly spread over the sub base including consolidation of sub base properly vibrating with th surface vibrator, finishing to line, level and slope, finally filling the joints with fine clean sand and cleaning the surface including removing existing shahabad stone and storing serviceale materials and disposing off the debris at the designated place within the colony,including taking permission from statutory authority etc complete all as per specification and as directed by the Engineer in charge.

Providing and Laying of Plain cement concrete using graded stone aggregate of 20 mm max size including consolidation, finishing, curing, cost of form work, shuttering, centering and dewatering etc.complete all as directed by the EIC.- Note: Laying of concrete shall be done by pumping wherever necessary as directed by EIC

Brickwork for stool,Benches(Curved) other Architect designs of thickness from 0.115 to 0.23m using bricks as specified with cement mortar 1:4 in superstructure including curing, raking out joints above ground level simultaneous pointing below ground level etc. complete as per specification and as directed by the Engineer in charge.

In super structure

Cement plastering 20 mm thick on stone masonary using factory manufactured pre mix/ready mix mortar in CM 1:4 of 'Roofit Mix'of M/s Premier Floor to Roof Materials pvt.ltd/ 'Easy plast' of M/s Walplast Products pvt.ltd/ 'Readiplast' of M/s Ultratech Cement Ltd/ 'Soundplast PMC-1' of M/s Sound buildcare pvt.Ltd/ or other approved equivalent make, having minimum composition of C:S :: 1:4 using fully treated dry, well graded natural sand conforming to IS 383 suitable for external plastering, having low rebound properties, low water demand for curing properties, mechnical mixing with water in a metalic tray only to make good consistency as per the specification of the Manufacturer and applied on over brick walls or concrete surfaces or RR masonry at all floors and levels, including membrane curing by applying one coat of factory made curing compound Resikure of M/s Anuvi Chemicals, Dr. Fixit curing compound or other equivalent over repaired surfaces as per manufacturer's specification, including scaffolding and removing existing damaged/ worn out plastering and disposing off debris at the designated place within the colony etc. complete all as per specifications and as directed by EIC.

Providing and fixing structural steel (fy = 250 N/mm² M. S. Angle, M. S. Channel, M. S. Flat, plates, pipes,tubes, nut & bolts, anchor fasteners etc. for bridge, roof truss, frames, gate and railing at all levels and location as per approved design, drawings issued by EIC and pattern including supplying, cutting, fabricating, welding , erecting and fixing in position, including necessary scaffolding ,including painting one coat redoxide primer and two coat of synthetic enamail paint of premium quality of approved manufacturer, approved shade and pattern ( bamboo finish texture for hand railings with different shade to simulate joints in bamboo) etc. complete all as per direction of Engineer-In-Charge.

Providing & laying Design Mix Reinforced cement concrete of M-30 grade using graded stone aggregate of 20mm max. size including mechanical mixing, placing , vibration, consolidation, finishing, curing, including necesary scaffolding etc. all Complete at all floors and heights / levels, in column & footing as specified including dewatering, if any ( excluding cost of steel reinforcement which shall be paid in the relevent item) as per drawings , specifications and as directed by Engineer-in-charge.

Reinforcement for reinforced cement concrete conforming to latest relevent IS Std. at all floors & levels including, supplying, cutting, bending, fixing and tying in position with 1.6 mm dia soft drawn annealed binding wire including cost of binding wire, labour etc. complete all as per specifications and as directed by the Engineer-in-Charge. Note:Binding wire required for the work will have to be supplied by the contractor & the same will not be measured for payment.

a)With high yield strength deformed bars Fe 500 grade

Providing and applying one coat of base coat (Floor coat Emulsion of M/s. Indigo paints or other approved equivalent) and two top coats of Floor coat Emulsion coating of Indigo paints or other approved equivalent make and shade over the Paver blocks at all locations as required, as per manufaturer's specification including preparation of surface, cleaning surfaces with waterjet etc. all Complete as directed by the EIC.

Providing and applying one coat of base primer (Apex Ultima protect of M/s. Asian paints or Aquatech of M/s. ICI Dulux or equivalent) and two top coats of acrylic water proof exterior coating of Weathershield flexx rainproof system of M/s. ICI Dulux or other approved equivalent make and shade over the sand face / form finished surfaces / rough cast plaster at all locations as required, thoroughly mixed and applied at an interval of 6-8 hours for each successive coats and ensure consumption of 0.47 ltr/Sqm for 3 coats,(base coat @.29 Ltr/sqm & two top coats @0.18 Ltr/sqm ) for sand face surfaces including preparation of surface, cleaning and filling the cracks and crevices with Latex caulking crack filler etc. Complete generally as per the manufacturer's specification and as directed by the EIC.

a) Over sand faced plastered / Form finished surfaces/ RRM walls

Providing and laying at all floors and levels Vitrified tiles of first quality Marbonite of M/S H&R JOHNSON (INDIA) Ltd/ Kajaria or other equivalent approved make of Wooden finish/ Natural stone finish and of 10 mm thickness or as per manufacture's specifications, laid directly over tile using polymer cum cement based adhesive manufactured by Roffe construction or M/s Bal Endura chemicals or other approved equivalent in respect of flooring and fixed over 12 mm thick backing cement mortar 1:3 in respect of skirting , close jointed and grouted white /colour cement slurry with pigments to match the colour of the tiles, finished to level, line, slope and plumb including cutting of tiles, making openings / cut out where necessary including wastage for odd shape of room and final cleaning of surfaces as required, curing etc. complete all as per specification, relevent IS code & as directed by the Engineer-in-Charge. Note: 1) In case of non-availability as per item, other makes which can be considered are 'Asian', 'Oracle Granito Ltd.', 'Orient', Regency. 2 ) No claim for payment of over thickness of adhesive for tile over tile work considered by the Department.

a) In flooring with tiles of approved colour,shade and texture similar to Wood finish in Digital print of M/s Kajaria laid directly over existing tile using tile on tile polymer cum cement based adhesive.

Providing and fixing in position at all floors, levels / heights 18mm thick mirror polished natural stones slab of approved shade, finished sizes as directed including machine cut / hand cut, final cleaning, moulding and polishing of exposed edges, inline, level, plumb and fixing the stone with cm 1:3, 20mm backing & overlapping of 20mm shall be fixed with Araldite adhesive, with best workmanship, finishing, curing, including removing existing door frame, shutter & fittings etc.and depositing the same at dept store etc. complete all as per specifications, drawings & as directed by the Engineer-in-Charge

a) Jet Black Granite Stone with mirror polish

b) unpolished granite

Providing and applying synthetic plaster of approved colour/ shade and texture of renova / Ruf-N-Tuf / herritage/ spectrum (or) any other approved equivalent in three coats ( one coat of synthetic plaster and two over coats ) all as per manufacture's specification and recommendation's at all level and locations in line level and plumb etc. including scaffolding roughning the existing surfaces by mechnical means like grinder etc. to receive synthetic plaster, all surfaces, removing the fungus growth if any, filling cracks and crevices etc. complete all as per specifications and as directed by the Engineer-in Charge.

(a) In Single Shade and Colour

Centering and shuttering including strutting, propping etc. and removal of form for :

a) circular/ rectangular Columns, piers, abutments, pillars, posts and struts

Providing and fixing in position G.I. chain link fencing of 8 gauge and mesh size of 50mm x 50mm to M.S. post including scaffolding fixing the same with necessary ‘J’ hooks, bolts , nuts, washers, staples, 6mm M.S.Fixing rods including necessary scafolding and applying two coats of sythetic paint over one coat of steel primer etc. complete all as per direction of Engineer-In-Charge.

Painting old/New steel work with two coats of synthetic enamel paint of approved shade existing scheme of Bamboo & make over one coat of steel primer including preparing surfaces, filling with putty wherever required, scaffolding & cleaning etc. complete all as per specifications & as directed by the Engineer-in-Charge

a) On steel surfaces with two finishing coats over a coat of steel primer.

Raised and cut pointing to stone work with cement mortar 1:3, including raking out joints, pointing neatly and finishing the joints as specified below including curing, scaffolding etc. complete all as directed by the Engineer-in-Charge.

Providing, laying and fixing in position 20 mm thick machine cut sand stone slab in required sizes, shade, shape and pattern in plane/curve or any geomatric shape of approved quality and colour in flooring/ skirting/ cladding at all location with 12mm thick cement mortar backing of mix 1;3 (1 cement :3 coarse sand) including providing and fixing with required stainless steel pins/ clamps/ dowels, drilling holes making notches etc. for securley fixing with cram/ pins to walls, including epoxy resin based (Araldite or equivalent) adhesive, gray cement slurry/ paste and grouting the joints matching colur inclunding rounding the (edges in semi circle) exposed edges, polishing all exposed faces etc. complete as per specification, drawing and as directed Engineer-In-Charge.

Providing and laying at all floors and levels 8mm. (min) thick or as per specification of approved manufaturers clay tiles cladding as per approved pattern and colour in cement mortar bedding/ backing, close jointed and grout with matching cement slurry to match colour of the tiles, finished to level, line, slope and plump including cutting of tiles, making openings/ cutout if necessary, wasteage and final cleaning of surfaces as required, curing etc. complete as per specification, drawing and as directed Engineer-In-Charge.

a) in cladding with approved design/ pattern etc. laid over 12mm thick cement bedding 1:3 backing

Providing and laying non pressure NP2 class RCC Hume pipes of approved make, with collars jointed with stiff mixture of cement mortar in proporation of 1:2 laying to the levels, slope and as per the drawing and specification and as directed by the Engineer-In-Charge including testing of joints etc. complete.

a) 450mm dia RCC Hume pipe class NP2

b) 600 mm dia RCC Hume pipe class NP2

Providing, fixing one side polish granite stone name plaque at Entrance wall made up of 18 mm thick single piece stone of size (1.6m x 0.85m) with Hindi & English letter writing with golden engraving,araldite at back surface and sand spreading for bonding, as per drawing etc. all complete as directed by Engineer-In-Charge.