Remaining work of Construction of Medical College and Up gradation of District Hospital at Koderma

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Ordinary rock

Hard rock (blasting prohibited)

Excavating trenches of required width for pipe, cables etc including excavation for sockets ,& dressing of sides ,ramming of bottoms ,depth upto 1.5m including getting out the excavated soil,& then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming ,watering, etc and disposing of surplus excavated soil as directed, within lead of 50m.

All kinds of soil

Pipes, cables etc exceeding 80 mm dia but not exceeding 300 mm dia

Excavating trenches of required width for pipes, cables, etc including excavation for sockets,depth upto 1.5 m, including getting out the excavated matterials, returning the soil as requred in layers not exceeding 20 cm in depth including consolidating each deposited layers by by ramming, watering,etc. and stacking serviceable material for measurements and disposal of unserviceable matterial for measurement and disposal of unserviceable matterial as directed within a lead of 50m:

Ordinary rock

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Hard Rock

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

All kinds of soil

Ordinary or hard rock

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50m and lift upto 1.5 m.all complete as per building specification and direction of E/I ( mode of measurement compacted volume).

ProvidIng coarse clean sand In filling in foundation trenches or In plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour. royalty and taxes all complete as per building specification and direction of Ell ( Mode of measurement compacted volume).

C O N C R E T E W O R K

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of grade excluding the cost of centering and shuttering - all work up to plinth level

1:5:10 (1 cement : 5 coarse sand : 10 graded ston aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets etc. upto floor five level, excluding the cost of centring, shuttering and finishing :

1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

REINFORCED CEMENT CONCRETE

Centering and shuttering including strutting, propping etc. and removal of form for all heights

Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, butteresses, plinth and string course etc

Suspended floors, roofs, landings, balconies and access platform.

Shelves ( Cast in situ )

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Extra for shuttering in circular work (20% of respective centering and shuttering items)

beams

Columns,

Stairs, (excluding landings) except spiral-staircases.

Small lintels not exceeding 1.5m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like.

Edges of slabs and breaks in floors and walls.

Under 20 cm wide

Weather shade, Chajjas, corbels etc., including edges.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).

Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Providing Tor steel reinforcement of 8mm. dia rods as per approved design and drawing -do- -do- TMT Fe 500 {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

Providing Tor steel reinforcement of 10mm,12mm & 16 mm. dia bars as per approved design and drawing -do- -do-

a) 10 mm (TMT coiI Fe 500) {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

b) 12 mm (TMT coiI Fe 500) {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

c) 16 mm (TMT coiI Fe 500) {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

Providing Tor steel, reinforcement of 20mm, 25mm, 28mm, 32mm dia bars as per approved design and drawing-do- -do-

20/25 mm dia,TMT bar Fe 5OO {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

28/32 mm dia,TMT bar Fe 5OO {Only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel steels Ltd. Bokaro and Vizag (RINL)}

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of engineering in charge. (Note :- Cement content considered in this item is @330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately)

All works upto plinth level

All works above plinth level upto floor V level

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All works upto plinth level

Concrete of M30 grade with minimum cement content of 350 kg /cum

All works above plinth level upto floor V level

Concrete of M30 grade with minimum cement content of 350 kg /cum

Providing M-30 grade concrete instead of M-25 grade BMC / RMC. (Note:- Cement content considered in M-30 is @ 340 kg/ kg/cum)

Providing, hoisting and fixing up to floor five level precast reinforced cement concrete in small lintels not exceeding 1.5m clear span up to floor five level, including the cost of required centering, shuttering but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in-Charge. (Material shall confirm to ASTM 6063)

Floor Joint of 100 mm gap

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).

Wall Joint of 100 mm gap

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre- engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063).

Roof Joint of 100 mm gap

B R I C K W O R K (A)

Providing designation 75 A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 Including providing 10 mm thick mortar joints. cost of screentng materials raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75 A brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 Including providing 10 mm thick mortar joints. cost of screentng materials sacffolding, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 100 A brick Work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth. curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 100 mm/ 125 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with 150mm/230mm/300 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening matenals, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Cement mortar 1:4 (1 cement :4 coarse sand)

Half brick masonry with non modular fly ash bricks of class designation 10, conforming to IS : 12894, in super structure above plinth and upto floor V level.

Cement mortar 1 : 4 (1 cement : 4 coarse sand)

Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

M A R B L E W O R K

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade

Area of slab up to 0.50 sqm.

Area of slab over 0.50 sqm.

Extra for providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Granite work.

Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminium fittiings such as hinges, tower bolts, handle, cleast and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in doors and windows with black board core bended with high quality phenol formal dehydes synthetic resin both side commercial veneered of standard make with oxidized iron fittings such as hinges, tower bolts, handle, cleast and sand blocks and taxes all complete as per building specification and direction of E/I.

25mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (over all area of door shutter to be measured).

Extra for providing frosted glass panes 4 mm thick (weight not less than 10 kg per sqm) instead of ordinary float glass panes 4 mm thick (weight not less than 10 kg per sqm) in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Float glass panes

5.0 mm thick glass panes (weight not less than 12.5 kg per sqm)

Extra for providing vision panel not exceeding 0.1 sum in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured) :

Rectangular or square.

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Single rubber stopper

Twin rubber stopper

Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

300 mm sliding door bolt

250 mm sliding door bolt

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

250 mm tower bolt

150 mm tower bolt

100 mm tower bolt

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

100 mm door handle with plate

75 mm door handle with plate

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete.

Size 40 mm

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.

Triple strip vertical type

Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate/ Square bar as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.)

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.

With 12 mm mild steel U beading

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealant shall be paid separately) Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

uPVC Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

1.0 mm thick

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter. The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634- 1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threadedstar headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).

Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 50 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

35 mm thick

S T E E L W O R K

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Hot finished welded type tubes

Electric resistance or induction butt welded tubes

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

Profile B

Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 part 1 and M.S. top cover of required thickness for rolling shutters.

80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutters.

Exceeding 10.00 sqm and upto 16.80 sqm in the area

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators side /top /centre hung with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer , but excluding the cost of other fittings, complete all as per approved design (sectional weight of only steel members shall be measured for payment).

10.11.1 Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete lock 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.

M.S. tube

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

F L O O R I N G

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) :

Light shade pigment using white cement

Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge.

In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)

Acid and alkali resistant tile

In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand)

Acid and alkali resistant tile

62 mm thick cement concrete flooring with concrete hardener topping,under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm.

Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness.

Providing and laying Double Charge Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622/ ISO 13006, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand ), jointing with grey cement slurray @ 3.3 k.g / sqm including grouting the joints with white cement and matching pigments etc., complete size of tile 600 x 600 mm .

Size of Tile 600x600 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm diameter

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).

Size of Tile 600x600 mm

Providing and laying 25mm thick kotah stone slab flooring of approved size, texture and colour over 19mm. thick base of lime morter (1:1:1) (lime putty:surkhi:coarse sand) laid over and Jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandium stone including cost of curing, taxes and royalty all complete as per building speclflcationand direction of Ell.

iv) 600X600 mm Size

Providing and laying 25mm thick kotah stone tiles In risers of steps, skirting, and pillars of approved size, texture and colour laid over 12mm. thick cement mortar (1:3) and joined with grey cement slurry mixed with pigment to match the shade of the slab including rubbing to granolilthic finish with approved quality -do-

Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :

Raj Nagar plain

Providing and laying Ceramic (Anti Skid) glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Vitrified (rectified) tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, (type II adhesive) in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).

Size of Tile 1200x300 mm X 15 MM

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing & fixing in position Phenol bonded Bamboo wood flooring with planks of sizes 14mm thick, 1800mm length (minimum) and 130 mm wide(minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The flooring shall be fixed with tongue and groove interlocking system, with underlayment of 4mm thick expanded poly ethylene foam sheets having density 40kg/cum, over prepared surface with necessary quarter round planks of size 1900mm x 18mm and door reducer of size 1900mm x 44mm, wherever required. The bomboowood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of Engineer in-charge.

Providing & fixing in position Phenol bonded Bamboo wood in wall skirting with planks of sizes 14mm thick, 1900mm length (minimum) and 85mm wide(minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC). The skirting shall be fixed with SS screws & rawl plugs, over underlayment of 4mm thick, expanded polyethylene foam sheets having 40kg/cum density over prepared surface. The bamboowood planks shall have minimum density of 1000Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.

Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paverfinisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achievethe desired density, complete as per specifications and directions of Engineer-in-Charge.

Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having water absorption less than 0.5% and conforming to IS: 15622, of approved make in all colours and shades in outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer- in-Charge

60mm thick Cement concrete paver block of M-35 grade with approved colour, design & pattern.

In rows 5 cm apart in both directions

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Extra for Kota stone/ sand stone in treads of steps and risers usingsingle length up to 1.05 metre.

Extra for pre finished nosing to treads of steps of marble/ granite stone.

Extra for marble/ granite stone flooring in treads of steps and risers using single length up to 2.00 metre.

Roofing work

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion.

110 mm bend

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Shoe (Plain)

110 mm Shoe

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum moisture resistant board

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).

6 mm thick Cement fiber board as per IS: 14862

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with :

GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing.

F I N I S H I N G

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Neat cement punning.

15 mm cement plaster on rough side of single or half brick wall of mix:

1:6 (1 cement: 6 coarse sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Providing 6mm thick cement plaster (1:4) in ceiling with clean of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/I.

Making 6x6mm grooves in plaster surface over walls truly horizontal of vertical as specified at regular intervals, at all heights including cleaning, finishing, scaffolding and curing with all leads and lifts of water all complete as per building specification and direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone of fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I

providing two coat of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty whwerever required scaff folding washing of floors and texes all complete as per building specification and dircetion of E/I

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

Two coats

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

White washing with lime to give an even shade :

New work (three or more coats)

Painting steel work with synthetic enamel paint of approved brand and manufacture to give an even shade, two or more coats.

French spirit polishing :

Two or more coats on new works including a coat of wood filler

Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Finishing walls with Acrylic Smooth exterior paint of required shade :

New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing two coat of synthetic enamel paint of approved shade and make over new wooden surface do/-

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

Two coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta ventilated rainscreen tiles of height 250/ 300/ 400mm and length of 595 mm of approved texture,design and pattern having Flexural Strength/ Modulus of Rupture of ? 14 N/m² and maximum water absorption of 10% tested as per ISO 10545-4:2004(E) and ISO 10545-3:1995 respectively in true level fixed to a supporting aluminium framework(Alloy 6063 T5/T6) consisting of vertical 'T' (for intermediates)/ 'L'(for ends/ termination)/ Tubular sections (at corners)of size 80x60x2mm/ 40x60x2mm/ 40x40x2mm respectively, spaced at maximum spacing of 600mm c/c matching to the tile vertical grid, and horizontal aluminium 'C'-clamps of size 56x25x2mm thickness of length 150mm at junction of tiles and of length 75mm at wall ends/ corners fixed on top of the vertical sections at spacing of 250/ 300/ 400mm c/c matching to the tile horizontal grid with two numbers of self-drilling / self-tapping SS screws of size 5.5x25 mm with EPDM washers.The vertical 'T'/'L/ Tubular' sections shall be fixed to the wall using HDG (hot-dip-galvanized) steel L-brackets (galvanizing thickness of minimum 80 microns)of size 110x80x6 mm at intermediate vertical aluminium profiles and of size 220x110x12 mm at outer corners and stainless steel grade 304,M10 full threaded anchor fasteners with nylon sleeve 100mm long (for brick work) and M8 expansion anchor fasteners 75mm long for concrete surface, spacing of brackets to be based on a structural/ static calculation.

The brackets shall be of length 175mm at junction of two vertical aluminium profiles and of length 100mm at intermediate points of vertical profiles and shall be fixed to the vertical aluminium T / L / Tubular profiles using two numbers self-drilling/ self-tapping SS screws of size 5.5x25mm with EPDM washers. EPDM gaskets to be fixed in between brackets and vertical profiles. The tiles shall be mounted on the ‘C’ clamps such that the tiles are supported at top and bottom at both ends. The tiles shall be additionally secured to the horizontal ‘C’ clamps using special SS clips of required size which shall be inserted and pressed into position on the ‘C’ clamps holding the tiles and the cut-tiles shall be glued at points to the horizontal ‘C’ clamps by using MS Polymer sealant adhesive. Thevertical joint open groove between two adjacent tiles shall be 5mm. The tiles and system shall be designed to resist wind load as per IS 875 (Part 3) according to different zones. The tiles shall be installed using the ventilated rain screen principle with provision for natural ventilation of the space between the façade tiles and the structural wall. The work shall be carried out as per specification, drawing and as per direction of the Engineer-in-Charge. Note : Scaffolding wherever required to be paid separately.

With 16mm thickness (+/- 10%) terracotta tiles of other than grey colors

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.

For thickness of tiles 10 mm to 25 mm

Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Brick Coba

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Embankment Construction with Material Obtained from Borrow Pits (Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2)

Rolling with vibratory roller

Plant Mix Method (Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 )

for grading- I Material

for grading- II Material

for grading-III Material

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Supplying and stacking at site.

90 mm to 45 mm size stone aggregate

63 mm to 45 mm size stone aggregate

53 mm to 22.4 mm size stone aggregate

Stone screening 13.2 mm nominal size (Type A)

Stone screening 11.2 mm nominal size (Type B)

Red bajri

Good earth

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density .

"Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints ( 10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars not to be paid separately).

Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

Cement concrete prepared with batch mixing machine

Footpaths and Separators (Construction of footpath/separator by providing a 150 mm compacted granular sub base as per clause 401 and 25 mm thick cement concrete grade M15, over laid with precast concrete tiles in cement mortar 1:3 including provision of all drainage arrangements but excluding kerb channel.)

Dry Lean Cement Concrete Sub- base (Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing.)

Cast in Situ Cement Concrete M20 kerb (Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M-10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408)

Using Concrete Batching and Mixing Plant

Retro- reflectorised Traffic signs (Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)

90 cm equilateral triangle

60 cm equilateral triangle

60 cm circular

80 mm x 60 mm rectangular

60 cm x 45 cm rectangular

60 cm x 60 cm square

90 cm high octagon

Direction and Place Identification signs upto 0.9 sqm size board. (Providing and erecting direction and place identification retro-reflectorised sign asper IRC:67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing)

Direction and Place Identification signs with size more than 0.9 sqm size board. (Providing and erecting direction and place identification retro- reflectorised sign asper IRC :67 made of encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing)

Overhead Signs (Providing and erecting overhead signs with a corrosion resistant aluminium alloy sheet reflectorised with high intensity retro-reflective sheeting of encapsulated lense type with vertical and lateral clearance given in clause 802.2 and 802.3 and installed as per clause 802.7 over a designed support system of aluminium alloy or galvanised steel trestles and trusses of sections and type as per structural design requirements and approved plans)

Truss and Vertical Support

Aluminium alloy plate for over head sign

Painting Two Coats on New Concrete Surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces)

Painting on Steel Surfaces (Providing and applying two coats of ready mix paint of approved brand on steel surface after through cleaning of surface to give an even shade)

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.)

Kilo Metre Stone (Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc)

Ordinary Kilometer stone (Precast)

Road Delineators (Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide stripes, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and confirming toIRC-79 and the drawings.)

Reinforced Cement Concrete Crash Barrier (Provision of an Reinforced cement concrete crash barrier at the edges of the road, approaches to bridge structures and medians, constructed with M-20 grade concrete with HYSD reinforcement conforming to IRC:21 and dowel bars 25 mm dia, 450 mm long at expansion joints filled with pre-moulded asphalt filler board, keyed to the structure on which it is built and installed as per design given in the enclosure to MOST circular No. RW/NH - 33022/1/94-DO III dated 24 June 1994 as per dimensions in the approved drawing and at locations directed by the Engineer, all as specified)

M 20 grade concrete

Metal Beam Crash Barrier

Type - B, "THRIE" : Metal Beam Crash Barrier (Providing and erecting a "Thrie" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 85 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 2 m high with 1.15 m below ground level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a space of channel section 150 x 75 x 5 mm, 546 mm long complete as per clause 810)

Spreading of Sludge Farm Yard Manure or/and good Earth (Spreading of sludge farm yard manure or/ and good earth in required thickness (cost of sludge, farm- yard manure or/and good earth to be paid for separately))

Grassing with ' Doobs' Grass (Grassing with 'Doobs' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for moving including supplying good earth if needed)

In rows 15 cm apart in either direction

In rows 7.5 cm apart in either direction

Making Lawns including Ploughing and Dragging with 'Swagha' Breaking of Clod (Making lawns including ploughing and breaking of clod, removal of rubbish, dressing and supplying doobs grass roots and planting at 15 cm apart, including supplying and spreading of farm yard manure at rate of 0.18 cum per 100 sqm)

Maintenance of Lawns or Turfing of Slopes (Maintenance of lawns or Turfing of slopes (rough grassing) for a period of one year including watering etc)

Turfing Lawns with Fine Grassing including Ploughing, Dressing (Turfing lawns with fine grassing including ploughing, dressing including breaking of clods, removal of rubbish, dressing and supplying doobs grass roots at 10 cm apart, including supplying and spreading of farm yard manure at rate of0.6 cum per 100 sqm)

Maintenance of Lawns with Fine Grassing for the First Year

a) Planting Permanent Hedges including Digging of Trenches (Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metres and supplying and planting hedge plants at 30 cm apart)

Maintenance of Hedge for one year

a) Planting Flowering Plants and Shrubs in Central Verge

Maintenance of Flowering Plants and Shrubs in Central Verge for one Year

Planting of Trees and their Maintenance for one Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year)

Renovation Lawns including, Weeding, Forking the Ground, Top Dressing with Forked Soil (Renovation lawns including, weeding, forking the ground, top dressing with forked soil, watering and maintenance the lawns, for 30 days or more, till the grass forms a thick lawn, free from weeds, and fit for moving and disposal of rubbish as directed, including supplying good earth, if needed but excluding the cost of well decayed farm yard manure)

Supply at Site Well Decayed Farm Yard Manure (Supply at site of work well decayed farm yard manure, from any available source, approved by the engineer in charge including screening and stacking)

Tree Guard with MS Angle Iron and Steel Wire (Providing and fixing tree guard 0.60 metre square, 2.00 metre high fabricated with MS angle iron 30 x 30 x 3 mm, MS iron 25 x 3 mm and steel wire3 mm dia welded and fabricated as per design in two halves bolted together)

SANITARY INSTALLATIONS

Supplying , fitting and fixing vitreous white glazed earthen ware I.W.C of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I 'p' trap 15 liters C.I.pull and let go flushing cistren of names or other I.S.S. equivalent make , complete with all fitting , C.I.or C.C. brackets 32mm alkathene/P.V.C telescopic flush , pipe about 2 M long with one brass coupling and clamps GI ,chain and pull including supplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less thane 50grms. 15mm P.V.C. connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coats of red oxide primer etc. all complete as per specification and direction of E/I.

(A) 580 mm. long

(b) With 12.5 lit. low level C.I. Cistem

Supply, fitting and fixing 40mm high vitreous white glazed earthen E.W.C with 'p' trap of parry hindustan or any other approved ISS make including supplying and fixing 15 liters CI mosquito proof low down flushing cistern of approved make with complete fittings with CI handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grams 15 mm PVC alkathene pipe 45 cm. long with brass coupling at both ends and white /black plastic solid state seal and lead of commander /cuckoo or other ISS with hinges or screws etc painting pipe and cistern etc with 2 coats of approved paint over a coat of red oxide priming, all complete as per specification and direction of E/I

(ii) E.W.C. with 'S' trap

(a) 12.5 lit. low level C.I. Cistem

Supplying fitting and fixing flat back or angular, lipped front vitreous white glazed earthen ware urinal of Hindustan "Parry" or any other approved ISS make with 5 liters capacity C.I. automatic fulsing cistern of reliance for any other I.S.S. approved make with all fittings clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grams 15 mm P.V.C /Alkthene pipe 450 mm long with bras coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a priming coat of red oxide cutting wall and floor, making good the same etc all complete as per specification and direction of E/I

(a) Flat back or standing corner (600mmx350mm)

Supplying and fitting and fixing viterous white glazed earthern ware wash hand basin of parry or Hindustan or any other I.S.S approved make supported or painted C.I. or R.S. brackets 32 mm C.I. brass waste, 15 mm dia C.I. body brass spindle stop cock of approved qaulity of weight not less than 350 grams, 32 mm P.V.C waste pipe 750 mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I

Supplying fitting and fixing H.C.I. pipes with ear of approved make confirming to I.S.I. 1729 including supplying nails and bobins short pieces, cutting loose collars,lead and yarn for making lead caulked joints, cutting pipes to size including earth work or scaffolding where necessary etc. all complete as per specification and direction of E/I.

(a) 100 mm dia

(b) 75 mm dia

Supplying and fixing H.C.I. fittings of approved make confirming to I.S.S. 1729 including supplying nails and bobines lead and yarn from making lead caulked joints including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/I.

(A) H.C.I. single junction with door but without ear except socket

(i) 100 mm dia(wt. 10.5 Kg. app.)

(B) H.C.I Heal rest bend

(i) 100 mm dia(wt. 5.5 Kg. app.)

(C) 100 mm dia H.C.I. "P" Trap with

Anti Syphonage Horn (wt. 8.5 kg app.)

(D) H.C.I double junction with doorand ear

(i) 100 mm dia(wt. 15.5 Kg. app.)

(E) H.C.I. double inverted Jn.

(100 mm x 50 mm x 50 mm size)

(F) H. C. I. offsets with ear

(i) 100 mm dia (wt. 6 kg. app.)

(G) H.C.I. Bend with door and ear

(i) 100 mm dia (wt. 6.5 kg. app.)

(H) H.C.I. plain bend with ear

(i) 100 mm dia (wt. 5.5 kg. app.)

(J) Floor trap with grantings

(i) 100 mm dia

(K) Northon patent H.C.I. Cowel

(i) 100 mm dia (wt. 3.25 kg. app.)

(L) H.C.I. pass over

(i) 100 mm dia

Supplying all tools and labours and cutting chajja, Cornice, for laying H.C.I. pipes and making good the same as per specification and direction of E/I.

Cutting drain width wise above G.L. for laying H.C.I. pipe and restoring brick work in cement mortar (1:4) 12mm cement plaster in (1:4) with neat cement punning as per specification and direction of E/I.

Making holes in walls for laying H.C.I. pipes and restoring the same after pipe laying as per specification and direction of E/I.

(i) 125 mm dia

(ii) 250 mm dia

(v) R.C.C. Chajja

Supplying materials and labour for painting the exposed H.C.I. pipes and fittings with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.

(c) 80 mm dia

(c) 100 mm dia

Providing designation 75 A brick work in C.M (1:4) in foundation & plinth with approved quality of clean coarse sand of F.M 2 to 2.5 including providing 10mm thick mortar joints costs of screening, materials ,scafolding,rtaking out joints to 15mm depth curing, taxex and royalty all complete as per building specification and direction of E/I.

Provinding and fixing was basin wih C.I brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls whereever required :

White Vitreous China Wash basin size 550x400 mm with a 15mm CP Brass single hole basin mixer

Providing and fixing Salem Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with CI brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required.

Kitchen sink with drain board

510x1040 mm bowl depth 250mm

Kitchen sink withought drain board

610x 460mm bowl depth 200mm

Supply Installation, Testing & Commissioning of Response Indicator single LED / 2 LED.

Supply, Installation, Testing & Commissioning of 300 mm dia heavy duty exhaust fan for single phase 230 volt, 50HZ AC supply complete with motor, blades, frame, bracket, louver/ shutter etc as required. (HavellS Make, Cat No - Ventil Air - DSP or equivalent).

Providing & fixing PVC waste pipe for sink including PVC waste fitting Complete

Flexible Pipe

32mm Dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 1500x450mm

Providing and fixing MS holder bat clamps of approved design to pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc.

Providing and fixing PTMT Bottle Trap for Wash basin.

Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms.

Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms

Providing and fixing uplasticised PVC connection pipe with brass unions :

45 cm length

15 mm nominal bore

Providing and fixing toilet paper holder :

C.P. brass

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in charge.

Providing and fixing white vitreous china laboratory sink with CI brackets , C.P brass chain with rubber plug 40 mm C.P brass waste and 40 mm CP brass trap with necessary C.P brass unions complete including painting of fittings and brackets , cutting and making good the wall wherever required :

Size 600x450x200 mm

Water Supply

Providing & Fixing of Garden hydrant outlet consisting 1 No. 25mm dia. Ball valve,( Brass) for connecting rubber hose, pipes & fittings.

Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends)

20 mm dia, nominal bore

25 mm dia, nominal bore

32 mm dia, nominal bore

40 mm dia, nominal bore

50 mm dia, nominal bore

65 mm dia, nominal bore

80 mm dia, nominal bore

Providing and fixing G.I. Pipes complete with G.I. Fittings and clamps. including cutting and making good the walls etc. required for waste connection from W.B. , A.S.P., Sump Rising main etc. Complete.

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Constructing masonry Chamber 60x45x50 cm,inside with 75 class designation brick work in cement mortar 1:5 (1 cement:5 fine sand) for water meter complete with C.I. Doble flap surface box 400x200x200mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.

With F.P.S. bricks

Providing and filling sand of garding zone V or coraser grade all round the pipes in external work

Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete.

25mm nominal bore

32mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931

15mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm dia nominal bore

Provide and fixing PTMT ball cock of approved quality, colour and make complete with epoxy coated aluminium rod with L.P/H.P.H.D. plastic ball

50 mm dia NB, 242mm long. Weighing not less than 1240 gms.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

20 mm nominal bore

25 mm nominal bore

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved qaulity:

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS: 8931

15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore.

15 mm nominal bore

Providing and fixing PTMT grating of approved quality, colour and make 125 mm nominal dia with 25 mm waste hole

Providing and fixing PTMT grating of approved quality, colour and make 125 mm nominal dia without waste hole

Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms

Providing and fixing chlorinated poly vinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fitting, including fixing the pipewith clampsat 1 m spacing. This includesjointing of pipes &fittingwith one step CPVC solvent cement and cost ofcutting chases and making good the same including testing ofjoints complete as per direction of Engineer in Charge.(Concealed work including cutting chases and making good the walls etc.)

15mm nominal outer dia. Pipes.

20mm nominal outer dia. Pipes.

25mm nominal outer dia. Pipes.

32mm nominal outer dia. Pipes.

Constructing masonary chamber 30x30x50cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock with C.I. Surface box 100x100x75 mm ( inside) with hinged cover fixed in cement concrete slab 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement:5 fine sand: 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design with F.P.S. bricks.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Circular Tank

Making connection of GI distribution branch with GI main of 50-80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete.

25 to 40 mm nominal bore

50 to 80 mm nominal bore

Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality

15 mm dia, nominal bore

20 mm dia, nominal bore

25 mm dia, nominal bore

32 mm dia, nominal bore

40 mm dia, nominal bore

50 mm dia, nominal bore

65 mm dia, nominal bore

80 mm dia, nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc.(External work)

25 mm dia nominal bore

32 mm dia nominal bore

Making connection of GI distribution branch with GI main following sizes by providing and fixing tee, including cutting and threading the pipe etc, complete

Coupling/Socket

50mm to 80mm nominal bore

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (Exposed on wall)

15 mm dia, nominal bore

20 mm dia, nominal bore

25 mm dia, nominal bore

32 mm dia, nominal bore

40 mm dia, nominal bore

50 mm dia, nominal bore

EXTERNAL SEWERAGE & DRAINAGE INSTALLATIONS

Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm. top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5.

Drainage Work

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) alround 100mm dia. SW waste pipes including bed concrete as per standard design

Providing & fixing in position precast RCC manhole cover and frame of reqd. shape and approved quality.

Circular shape 560 internal dia.

Providing laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

150 mm diameter

200 mm diameter

250 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design.

150 mm diameter

200 mm diameter

250 mm diameter

Providing and fixing square mouth SW gully trap grade ‘A’ complete CI grating brick masonry chamber with bricks of class designation 75 and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. (COVER MIN. 4.5 KG & FRAME MIN.2.7 KG )

180x150mm size P type With FPS bricks

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.

150 mm dia RCC pipe

250 mm dia RCC pipe

300 mm dia RCC pipe

Construction brick masonry manhole in cement mortar 1:4 (1cement : 4coarse sand) RCC top slab with 1:2:4 mix 9 with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 coarse sand 4 graded stone aggregate 20mm nominal size) foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design.

Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610mm internal dimensiions total weight of cover and frame to be not less than 38 Kg. ( weight of cover 23 Kg. and weight of frame 15 Kg.), with FPS bricks with class designation 7.5

Inside size 120 x 90 cm and 90 cm deep including CI cover with frame (heavy duty) 500mm internal dia. Total weight of cover and frame to be not less than 116 Kg. ( weight of cover to be 58 Kg. and weight of frame 58 Kg.)with FPS bricks class designation 75. (Sewerage Line)

Extra for depth for manholes

Size 90 x 80 cm with FPS bricks designation 7.5

Size 120 x 90 cm with FPS bricks designation 7.5

Constructing brick masonary circular manhole 1.22m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design.

1.68m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including centering shuttering all complete. Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for seperately).

With F.P.S. bricks class designation 7.5

Extra for depth for circular manholes 1.22m internal dia (at bottom) with beyond 1.68m to 2.29m.

With F.P.S. bricks class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steel bar conforming to IS: 1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specification and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size) complete as per design.

Constructing brick masonry road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1:5 (1 cement : 5 fine sand) including 500 x 450 mm (heavy duty) precast RCC horizontal grating with frame complete as per standard design: with FPS bricks

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement cincrete 1:2:4 mix (1cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) cement plastered on both sides with cement mortar 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete for pipes 100 to 250mm dia.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves,chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing & reinforcement with1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size)

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work : 25mm dia nominal bore

Providing and laying non-pressure NP2 class ( light duty ) R.C.C pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement: 2 fine sand ) including testing of joints etc. complete : a) 450mm dia R.C.C pipe

ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, aneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

With stainless steel cover plate minimum 1.25 mmthickness

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia and size (Dash fastener to be paid for separately).

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).

Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately)

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-incharge

Powder coated minimum thickness 50 micron aluminium

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.

Upto 5mm depth and 5 mm width

Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete.

Powder coated minimum thickness 50 micron aluminium

WATER PROOFING

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Water proofing for Old and New Roof Slab:- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied with, brush, roller or spray for water proofing coating as per manufacturer specifications with following steps: (a) surface preparation-Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint / coating, and cement laitance by cleaning with compressed air & water jet including all materials, labour, tools complete. Ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage, leakage. On identification of seepage, cement grouting to be done with non shrink expanding admixture of Sika India Pvt Ltd /MYK Schomberg/Dr Fixit/Fosroc or equivallent Providing and reparing of all comers and joints such as those between the parapet wall and the roof slab etc shall be chamfered with 150 mm X 150 mm fillet of mortar (Cement: sand-1:4) admixed with acrylic polymer of Sika Fosroc/MYK Schomberg Fixit or equivalent. Before chamfering a prime coat shall be given with the slurry ofacrylic polymer. Repairing surface irregularities, damaged concrete in base slab, dead cracks if any, with an acrylic polymer modified repair mortar including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete. (b)1st Coat Apply 1st coat of two component acrylic modified, ready to use, flexible cementitious material on surface saturated dry roof and inside wall of Parapet wall upto 600 mm by brush or roiler After 1st coat of application, 45 gsm of Fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @1.50 kg / Samt/coat. For the purpose of measurement the entire treated surface will be measured."

(c) 2nd Coat-To apply the 2nd coat of two component acrylic modified, ready to use, flexible cementitious material right angle to the 1st coat over the glass fibre laid surface 2nd coat should be applied @0.7 kg/Samticoat For the purpose of measurement the entire treated surface will be measured After three days of drying the 2nd coat, the rail water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of EIC. The waterproof coating to be protected from damage before screed over it. Waterproofing Brand- Sika Topseal 109hi/Fosroc Brushbond RFX/Dr Foxit Pidiffin 2K/MYK Aquafin TG Product Performance - Chemical Base Part A Acrylic copolymer, Part B Specially graded cementitious powder- Density 1.6 kg/l (mixed density) at +27°C Tensile Strength -2 Nimm2 after 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Strength -2 N/mm2 (concrete failure) (According to ISO 4624) Slant-Shear Bond Strength -4 N/mm2 (According to FIP 5.15) Elongation at Break -35% without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370)

(d) Protection of treated surface with PCC-The treated surface should be covered with 25mm/ 50mm PCC of M-20 grade(1:1.5:3) with proper slope (1:120) towards the rain outlets in alternate panels of 2 mt x 2mt keeping 6 mm gap between the panel joint. Integral water proofing admixture conforming to IS 2645 @of 100 ml per bag of of cement to be added in the screed concrete(paid separately for this items) All corners shall be chamfered with 150mm x 150 mm fillet. The rain water outlets shall be just leveled with the screed concrete to ensure smooth discharge of water the peripheral gaps between pvc pipe outlet and concrete surface should be packed property with rich concrete and the peripheral mouth to be sealed with moisture insensitive epoxy putty of Sika India Pvt. Ltd. /MYK Schomberg/Dr Fixt/Fosroc For the purpose of measurement the entire treated surface will be measured." (e)Groove of PCC surface should be filled with Polysulphide Sealant (Paid Separately). Brand- Sika India Pvt Ltd./MYK Schomberg/Dr Foxit/Fosroc Warranty for five years.

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of :

(i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer.

Using rough kota stone.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge :

Using rough kota stone.

Covering of treated surface with PCC :- Providing 50 mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm to 6 mm size graded and cleaned sand of F.M 2.5 to 3 including screening,shuttering and mixing cement concrete in mixer with admixture of integral water proofing and placing in position,striking curing,taxexand royality all complete as per building specifiction and direction of Ell.Panels that has been left should be casted next day.There should be 6 mm gap between Panels .Brand-Sika­ P\astocrate plus, MYK proof WP 1O,Fosroc-Conplast X4211 C,Dr.fixit Pidiproof LW+ or Equivalent .

5.12.8. Providing and filling of 6 mm thickGroove between 25 mm PCC Panels with Polysulphide Sealant (Poring Grade)as per drawings and technical specifications and direction of E in Charge.(with 18% GST) .Brand:-Sika-Polysulphide, Fosroc-Thioflex 600,Dr. Fixit Pidiseal PS(42P),MYK Seal PS or Euivalent

SUB HEAD - STRUCTURAL GLAZING AND ALUMINIUM COMPOSITE PANEL

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass.

Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately.

The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or by any other accreditation body which operates in accordance with ISO / IEC 17011 and accredits labs as per ISO/ IEC 17025.

Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr

Static Water Penetration Test. (50pa to 1500p) as per ASTME- 331-09 testing method for a range up to 2000 ml.

Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml

Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm

Seismic Movement Test (upto 30 mm) as per AAMA 501.4- 09 testing method for Qualitative test, Tests to be conducted on site.

Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.

(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

CARRIAGE OF MATERIAL

Stone Chipps / stone aggregate (22km )

Coarse Sand ( 10 km)

Brick (8 km) (1 K + 7 P)

Fly Ash Brick (8 km )

Local Sand (10km)

Earth ( 5 km)

TUBEWELL

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 100mm dia

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed / plain bevel ended pipe (type A) of required dia, conforming to IS:8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete,for all depths, as per direction of engineer -in-charge :

200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of : 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete : 150 mm clamp

150 mm nominal size dia

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part

Providing and fixing brass gate valve with C.I. wheel of approved quality (screwed end)

25 mm dia. Nominal bore

32 mm dia. Nominal bore

40 mm dia. Nominal bore

50 mm dia. Nominal bore

65 mm dia. Nominal bore

80 mm dia. Nominal bore

Constructing masonry Chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:5 (1 cement : 5 fine sand) for stop cock, with C.I surface box 100 x 100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10graded stone aggregate 40mm nominal size) and inside plastering with cement mortat 1:3 ( 1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.

With common burnt clay F.P.S. ( Non Modular) bricks of class designation 7.5.

Constructing masonry Chamber 60x60x75cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for sluice valve, with C.I surface box 100mm. top diameter,160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10graded stone aggregate 40mm nominal size) and inside plastering with cement mortat 1:3 ( 1cement :3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design.

With common burnt clay F.P.S. ( Non Modular) bricks of class designation 7.5.

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rebber insertions etc. (The tail pieces if required will be paid seperately) :

100 mm dia nominal bore

ELECTRICAL WORKS

POINT WIRING

Point wiring in PVC conduit with modular type switch:- Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular switch, modular plate, suitable GI box etc as required.

Group A

Group B

Group C

Twin Control Point wiring in PVC conduit with modular type switch:- Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed PVC conduit, 2 way modular switch, modular plate, suitable GI box etc as required.

S/F light plug point with modular type accessories:- Supplying & Fixing suitable G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc as required.

S/F power plug point with modular type accessories:- Supplying & Fixing suitable G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch connection, painting etc as required.

S/F 20 amps SPN MCB industrial socket outlet:-Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

S/F Modular type switch/socket:- Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

TV anteena Socket Outlet

Telephone Socket Outlet

6A modular switch

6A modular socket

16A modular switch

16A modular socket

S/F Modular boxes, base & cover plate:- Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.

1 or 2 Module (75mmX75mm)

6 Module (200mmX75mm)

12 Module (135mmX205mm)

S/F Modular type electronic fan regulator:- Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of grade exceeding 1.1KV but not exceeding 11 KV of size not exceeding 400 sq.mm in the existing RCC/ HUME/ STONEWARE/ METAL Pipes as required.

11KV cable laying upto 400 sq.mm. in open duct.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of grade exceeding 1.1KV but not exceeding 11 KV of size not exceeding 400 sq.mm direct in existing masonary open duct as required.

Power plug wiring in PVC conduit (2x4 sq.mm) :- Wiring for light/ power plug with 2x4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Submain wiring in PVC conduit :- Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.

2x2.5 sq mm + 1x2.5 sq mm earth wire

4x2.5 sq mm + 2x2.5 sq mm earth wire

2x6 sq mm + 1x6 sq mm earth wire

2x10 sq mm + 1x10 sq mm earth wire

2x16 sq mm + 1x16 sq mm earth wire

4x6 sq mm + 2x6 sq mm earth wire

4x10 sq mm + 2x10 sq mm earth wire

4x16 sq mm + 2x16 sq mm earth wire

S/F S.P. MCB DB :- Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator).

8 way Double Door

12 way Double Door

16 way Double Door

S/F T.P. MCB DB :- Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plates, interconnections, phosphatized powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator).

4 Way (4+18), Double Door Horizontal Type

6 Way (4+18), Double Door Horizontal Type

8 Way (4+24), Double Door Horizontal Type

S/F VERTICAL TYPE T.P. MCB DB :- Supplying and fixing following way, three pole and neutral sheet, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable glands plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator).

12 Way (4+36), Double Door Vertical Type

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following rating 240 volts, C series MCB suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc as required.

6/32 A SP MCB

6/32 A DP MCB

40 A DP MCB

50/63 A DP MCB

6/32 A TPN MCB

40 A TPN MCB

50/63 A TPN MCB

S/F SPN RCCB :- Supplying and fixing of following rating double pole (Single phase & neutral) 240 volts, resudual current circuit breaker (RCCB), having a sensivity current up to 300 miliampere in the existing MCB DB complete with connections, testing & commissioning etc. as required.

S/F TPN RCCB :- Supplying and fixing of following rating TP&N, (Three phase and neutral), 415 volts, resudual current circuit breaker (RCCB), having a sensivity current up to 300 miliampere in the existing MCB DB complete with connections, testing & commissioning etc. as required.

Telephone wiring in existing conduit :- Supplying and drawing 2 pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

TV cable in existing conduit:- Supplying and drawing co-axial TV cable RG-6 grade copper conductor PE insulated, with PVC sheath in the existing surface/ recessed PVC conduit as required.

Supply Installation, testing and commissioning of follwing size ceiling fan 3 Blades confirming to13:374,.2019 including wiring the down rods of standard length (upto 30cm) with l.Ssq.mm. FR PVC insulated, copper wire suitable for 230V 50H2, single phase supply etc. complete as required.

S/F PVC conduit :- Supplying and fixing of following sizes of PVC conduit along with the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

20mm dia

50mm dia

S/F Electronic musical call bell :- Supplying and fixing electronic musical call bell suitable for D.C/A.C single phase, 230 volts, complete as required.

S/F Modular type blanking plate:- Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

S/F Batten Holder:- Supplying and fixing brass batten/ angle holder including connection etc. as required.

ITC exhaust fan upto 450 mm sweep:- Installation of exhaust fan upto 450mm in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc as required.

Wiring in existing conduit:- Supplying and drawing following sizes of FRPVC insulated copper conductor single core cable in existing surface/recessed steel / PVC conduit as required.

2 x 1.5 sq.mm

3 x 2.5 sq.mm (For Lift Shaft)

3 x 4.0 sq.mm (For Lift Shaft)

G.I. earth pipe electrode with salt/ charcoal:- Earthing with G.I. earth pipe 4.5 mtr long, 40 mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required.

G.I. earth plate electrode:- Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc as required. (with charcoal or coke and salt).

G.I. earth plate electrode (LA):- Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc as required. ( with charcoal or coke and salt).

Copper earth plate electrode:- Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc as required. ( with charcoal or coke and salt).

P/F 25mm x 5mm copper earth strip in surface/ recess :- Providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing earth bus of 50 mm x 5 mm copper strip on surface for connections etc. as required.

P/F 25mm x 5mm G.I. earth strip in surface/ recess :- Providing and fixing 25 mm x 5 mm G.I. strip on surface or in recess for connections etc. as required.

P/F 50mm x 5mm G.I. earth strip in surface/ recess :- Providing and fixing 50 mm x 5 mm G.I. strip on surface or in recess for connections etc. as required.

P/F 6 SWG G.I. loop earthing wire in surface/ recess :- Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

P/F 6 SWG G.I. loop earthing wire conduit/ cable:- Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

P/F G.I. lightning conductor finial:- Providing and fixing lightning conductor finial, made of 25mm dia 300mm long, G.I. tube, having single pronge at top, with 85mm dia 3mm thick G.I. base plate including holes etc. complete as required.

P/F G.I. lightning conductor tape in horizontal run:- Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run).

P/F G.I. lightning conductor tape in vertical run:- Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For Vertical run).

P/F Testing joint for G.I. lightning conductor :- Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

P/F G.I. lightning conductor :- Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) of size 60 cm X 60 cm at the bottam and 50 cm X 50 cm at the top with a thickness of 10 cm including inscription duly engraved as required.

P/F MV. danger notice plate :- Providing and fixing of MV danger notice plate of 200mm x 150mm made of mild steel, atleast 2mm thick and vitererous enammelled while on both sides and with inscription in single red colour on front side as required.

P/F H.T. danger notice plate :- Providing and fixing of H.T. danger notice plate of 250mm x 200mm made of mild steel, atleast 2mm thick and vitererous enammelled while on both sides and with inscription in single red colour on front side as required.

11KV cable laying upto 400 sq.mm. in pipes.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of grade exceeding 1.1KV but not exceeding 11 KV of size not exceeding 400 sq.mm in the existing RCC/ HUME/ STONEWARE/ METAL Pipes as required.

S.I.T.C of floowing rating surface mounted LED tube light fitting suitable for 230V 50H2, single phase supply etc. complete as required.

20122W LED Tube light

11KV cable laying upto 400 sq.mm. in open duct.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of grade exceeding 1.1KV but not exceeding 11 KV of size not exceeding 400 sq.mm direct in existing masonary open duct as required.

S.I.T.C of floowing rating reccess/surface mounted LED round/square shape Down light luminarie with pressure die cast housing for single phase supply voltage. Luminarie shall be confirm to IS:10322 part-5/section-2 or IEC:62722with all neccssary acc$sories as required

6/7W LED Round Down light

l2W LED Round Down ligbt

15/16W LED Square Down light

l8/20W LED Square Down light

Supply, Installation, Testing & Commissioning of 1x20 watt LED Light recess mounted downlight with high efficiency electronic driver. (Make Philips Cat No RC380B LED36S-6500 G4 L60W60 PSU or equivalent.)

Supply, Installation, Testing & Commissioning of 1x10 watt LED Mirror light fixture wall mounted with electronic high efficiency electronic driver as complete as required. (Philips Make, Cat No- BN021 LED 10S or equivalent).

Supply, Installation, Testing & Commissioning of Bulk Head Light Fixture surface mounted Philips make cat no- WT140 or equivalent.

CCTV SYSTEM (CONDUITING & WIRING ONLY)

TV cable in existing conduit:- Supplying and drawing co-axial TV cable RG-6 grade copper conductor PE insulated, with PVC sheath in the existing surface/ recessed PVC conduit as required.

Supply of following sizes of 1.1KV grade multicore Copper / aluminium conductor XLPE insulated and PVC sheathed armoured cable conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule by architect / consultant).

3.5 core, 25 sq.mm aluminium armoured cable

3.5 core, 35 sq.mm aluminium armoured cable

3.5 core, 50 sq.mm aluminium armoured cable

3.5 core, 70 sq.mm aluminium armoured cable

3.5 core, 95 sq.mm aluminium armoured cable

3.5 core, 120 sq.mm aluminium armoured cable

3.5 core, 150 sq.mm aluminium armoured cable

3.5 core, 185 sq.mm aluminium armoured cable

3.5 core, 240 sq.mm aluminium armoured cable

3.5 core, 300 sq.mm aluminium armoured cable

4 core, 10 sq.mm.

2 core, 10 sq.mm.

2 core, 6 sq.mm.

3.5 core 400 sq. mm

4 core 16 sq.mm

4 core 6 sq.mm

DIESEL GENERATING SET:

Design, Manufacturing, Supply, Receiving, Unloading, Shifting, Storing, Installation, Testing and Commissioning of Radiator Cooled DG sets of following capacity (rating in kVA) compact packaged silent type, with Outdoor type Acoustic Enclosure to reduce the noise level as per requirements of central pollution control board, 415Volts, 3 phase, 50 Hz AC alternator coupled to diesel engine with mechanical governor complete with all accessories, standard specifications tool kits, service manual, self starting device, fly wheel, coupling with guard, V velt, radiator, instrument panel (starting switch with key, Water Temperature indicator gauge, Lub OIl Pressure gauge, Lube oil temperature gauge, Battery Charging Ammeter, indicating lamp, hour counter etc.), residential silencer with insulation & aluminium cladding, common bed plate, anti vibration isolation pads, extended cable termination box, grouting bolts, first charge of engine oil, gear oil, high speed diesel oil, 12 volt maintenance free chargeable battery set with Trickle/Boost Battery charger, interface card for BMS connectivity complete as required of rating 415 Volts, 3 phase, 50 Hz. AC alternator coupled to Diesel Engine complete with all accessories. NOC from concerned goverment authority for installation and operation of D.G. set shall be taken by contractor. D.G. Set shall be as per CPCB-II.

500 KVA D.G. Set with suitable capacity of day oil fuel Tank

Supply, installation, testing & commissioing of 15 KVA UPS in paralleling mode at 0.9 input power factor with inbilt isolation transformer as per specification given in the document with following broad features.

THD(i) shall be less than 5% in the entire loading range.

UPS shall carry design output at 40 deg.

Shall have soft start and hold of for incoming supply.

Invertor capability to supply 150% load for 5 sec.

Three Phase Input and Three Phase Output. (Input - 340V - 470V, Three Phase, 4 wire. / Output - 400-415 Volt, Three Phase, 4 Wire.)

Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells.

Battery shall be external type with rack and suitable for 15 minute backup on 100% load.

UPS shall be compatible for parallel operation. (Synchronize). Parallel operation kit shall be supplied with UPS.

UPS described as above

Fixing louvers shutters for exhaust fan:- Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supplying and fixing of following sizes of STEEL conduit alonwith the accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

20mm dia

25mm dia

Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

100 mm wide x 50 mm depth x 1.6 mm thickness.

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

600 mm wide x 50 mm depth x 2.0 mm thickness.

750 mm wide x 62.5 mm depth x 2.0 mm thickness.

900 mm wide x 62.5 mm depth x 2.0 mm thickness.

Supplying and installing following size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

100 mm wide x 50 mm depth x 1.6 mm thickness.

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

600 mm wide x 50 mm depth x 2.0 mm thickness.

750 mm wide x 62.5 mm depth x 2.0 mm thickness.

900 mm wide x 62.5 mm depth x 2.0 mm thickness.

Supplying and installing following size of perforated pre-painted M.S. cable trays reducers with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

100 mm wide x 50 mm depth x 1.6 mm thickness.

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

600 mm wide x 50 mm depth x 2.0 mm thickness.

750 mm wide x 62.5 mm depth x 2.0 mm thickness.

900 mm wide x 62.5 mm depth x 2.0 mm thickness.

Supplying and installing following size of perforated pre-painted M.S. cable trays Tee’s with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

100 mm wide x 50 mm depth x 1.6 mm thickness.

150 mm wide x 50 mm depth x 1.6 mm thickness.

300 mm wide x 50 mm depth x 1.6 mm thickness.

450 mm wide x 50 mm depth x 2.0 mm thickness.

600 mm wide x 50 mm depth x 2.0 mm thickness.

750 mm wide x 62.5 mm depth x 2.0 mm thickness.

900 mm wide x 62.5 mm depth x 2.0 mm thickness.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Reducer with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

150 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

600 mm width X 50 mm depth X 2.0 mm thickness

750 mm width X 62.5 mm depth X 2.0 mm thickness

Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design:

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg).

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.

150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

Supply,Installation,Testingand Commissioning of on grid Solar Photo voltaic Power Plant conforming to MNRE specification sasam ended,consisting of Mono/Poly Cry stallinesilic on solarcells,net metering facility,necessary protections,earthing,mounted on Aluminium / GI structure of suitabl estrength with following components complete as required:-a) Solar Photo voltaic Module of capacity 330 Wp or above,manufactur edin India,conforming to IS14286 / IEC61215,IS/IEC61730-Part-1,IS/IEC61730-Part-2.Solar Photo voltaic Module conversion efficiency shall not beless than16.5%.PV module susedin solar power plants / system smustbe warranted for the irout put peak watt capacity,which should not beless tha Supply, Installation ,Testing and Commissioning of on grid Solar Photo voltaic Power Plant conforming to MNRE specification salamander, consisting of Mono/Polycrystalline silicon solar cells , net me teringfa cility, necessary protections, earthing,mountedon Aluminium/ GI structure of suitable strength with following components complete as required:-a)Solar Photo voltaic Module of capacity 330 Wp or above, manufactured in India,conforming to IS14286/IEC61215,IS/IEC61730-Part-1,IS/IEC61730-Part-2.Solar Photo voltaic Module con version efficiency shall not beless than16.5%.PV module sussed in solar power plants / system smustbe warranted for their out put peak watt capacity, which should not be less than 90 % at the end of 10 years and 80% at the end of 25 years.b) Power Conditioning Unit (PCU)of350-800VDC Input voltage range and 400 VAC,three phase,4 wire,50Hz+/-2.5Hz,out put voltage suitable to generate ACP ower with efficiency not less than 97%,tota harmonic distortion less than3%and suitable for ambient temperature from 0 to 50 degreeC.ThePCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency’s) Data Monitoring System complete with accessorised) Fixing of Array junction box & Main junction box with IP65 protection and termination arrangement for incoming and outgoing cable along with glands ,lugs and other accessories etc. as required) Lightning and surge voltage protection.f) Connections & Inter connectionsby supplying & fixing required size XLPE insulated copper conductor1.1kV grade armoured powerand control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel / conduit lug sand other accessories etc. as requiredn 90% attheend of10 years and 80%attheend of 25 years.b)PowerConditioningUnit(PCU)of350-800VDC Input voltage rangeand 400VAC,threephase,4wire,50Hz+/-2.5Hz,out put voltage suitable to generate AC Power with efficiency not lesst han 97%,to talharmonicdistortion less than 3%and suitable for ambien temperature from0to 50 degreeC.ThePCU shall adjustthe voltage and frequency level to suit the Grid Voltage Frequency.c) Data Monitoring System complete with accessories.d) Fixing of Array junction box & Main junction box withI P65 protection and termination arrangeme ntforinc oming and out going cable along withglands,lugsand other accessories etc. as required.e) Lightning and surge voltage protection.f) Connections & Inter connections by supplying & fixing required size XLPE insulated copper conductor1.1kV grade armoured power and control cables between solar modules,main power cable to grid supply PCU unit along with supplying & fixing of necessary channel / conduitlugs and other accessories etc.as required

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required.

3.5 X 25 sq. mm (28mm) For aluminium armoured cable

3.5 X 35 sq.mm (32 mm) For aluminium armoured cable

3.5 X 50 sq.mm (35 mm) For aluminium armoured cable

3½ X 95 sq. mm (45mm) For aluminium armoured cable

3½ X 120 sq. mm (45mm) For aluminium armoured cable

3.5 X 150 sq.mm (50 mm) For aluminium armoured cable

3½ X 185 sq. mm (57mm) For aluminium armoured cable

3½ X 240 sq. mm (63mm) For aluminium armoured cable

3½ X 300 sq. mm (70mm) For aluminium armoured cable

3½ X 70 sq. mm (38mm) For aluminium armoured cable

4 X 10 sq. mm (25mm)

2 X 10 sq. mm (19mm)

2 X 6 sq. mm (19mm)

4 X 25 sq. mm (28mm)

4 X 16 sq. mm (28mm)

3½ X 400 sq. mm (82mm)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required

CIRCUIT / SUBMAIN WIRING

2x1.5 sq mm + 1x1.5 sq mm earth wire

2x2.5 sq mm + 1x2.5 sq mm earth wire

4x2.5 sq mm + 2x2.5 sq mm earth wire

2x6 sq mm + 1x6 sq mm earth wire.

2x10 sq mm + 1x6 sq mm earth wire.

4x6 sq mm + 2x6 sq mm earth wire.

4x10 sq mm + 2x6 sq mm earth wire.

4x16 sq mm + 2x6 sq mm earth wire.

2x16 sq mm + 1x6 sq mm earth wire.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface /recess including cutting the wall and making good the same in case of recessed conduit as required.

Wiring for fire alarm system with following PVC insulated copper conductor 1100 volts grade stranded "FRLS" wires in existing conduits.

2 x 1.5 sqmm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL pipe as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonary duct as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

11 KV END TERMINATION:

Supply & making of INDOOR cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core XLPE aluminium conductor cable of 33 KV grade as required.

3C x 240 Sqmm, 33KV XLPE

Supply & making of OUTDOOR cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core XLPE aluminium conductor cable of 33 KV grade as required.

3C x 240 Sqmm, 33KV XLPE

HT CABLE LAYING:

Laying of one number XLPE power cable of 33 KV grade of following size in the existing masonry open duct as required.

Above 120 sq. mm and upto 400 sq. mm

Laying of one number XLPE power cable of 33 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Above 120 sq. mm and upto 400 sq. mm

Laying of one number additional XLPE power cable of 33 kV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

Above 120 sq. mm and upto 400 sq. mm

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required.

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A, “C” curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required

Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying,including painting the exposed portion of loop, all as per standard design complete.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required.

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 kV grade as required.

RISING MAIN-

Supplying, Installing on wall, testing and commissioning of following capacity Air Insulated Compact Type Rising Mains for use on 3 phase 4 wire 415 V, 50Hz A.C. supply with enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos. aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints & expansion joints, fire barrier at each floor, provision of tapping at every meter, continuous earthing with 2 Nos. aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as required.

HVAC WORKS

Double Skin AHU (CC + Pre Filter)

Supply, Installation, Testing and commissioning of factory built floor mounted chilled water double skin type horizontal/vertical air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8mm outside layer and 0.8 mm inside layer with polyurethane foam (PUF) insulation factory injected between them by injection moulding machine, complete with blower section with blower suitable for static pressure as required, minimum 2 bend GSS/PVC eliminators,cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5 mm) cooling coil of 6 row deep, filter section with 50 mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% V, 50Hz, 3 Phase AC supply suitably designed for varialbe frequency drive applications, drain connections, stainless steel (18G) drain pan with PUF insulation, 150 mm dia. dial type pressure gauges (2 Nos.) and industrial type thermometres (2 Nos.) at the inlet and outlet of coil, auto purge valve wherever required, necessary vibration isolation arrangement etc. complete as per specification and of following capacities.

Pressure Independant Balancing Cum Two Way Control Valve on Cooling Coil

Supply, installation, testing and commissioning of modulating type two-way pressure independent dynamic control & balancing valve with spring return feature. The valve shall be suitable for chilled/hot water duty and installed at each air handling unit. The minimum close off pressure actuator must be 1.5 times shut off head of pump or 5 bars whichever is maximum. The operation of valve shall be through Building Automation System and hence capable of recieving 0-10V or 4-20 mA signal from remote controllers. The valve shall be suited for installation on following pipe sizes. Price shall include the cost of Insulation, material and external treatment will be same as of pipe :

Note- The manufacturer shall guarantee the free replacement of 5 years for any defects found during operations.

19 mm Dia, Maximum 5 GPM

25 mm Dia, Maximum 9 GPM

32 mm Dia, Maximum 15 GPM

40 mm Dia, Maximum 26 GPM

50 mm Dia, Maximum 54 GPM

65 mm Dia, Maximum 80 GPM

80 mm Dia, Maximum 125 GPM

Chilled / Hot Water Piping With Factory Laminated Glass Cloth Nitrile Rubber Insulation

Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density (Factory Laminated Glass Cloth Nitrile Rubber Insulation), thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect.

Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.

250 mm dia. (32 mm thick insulation)

200 mm dia. (32 mm thick insulation)

150 mm dia. (32 mm thick insulation)

125 mm dia. (32 mm thick insulation)

100 mm dia. (32 mm thick insulation)

80 mm dia. (32 mm thick insulation)

65 mm dia. (32 mm thick insulation)

50 mm dia. (32 mm thick insulation)

40 mm dia. (32 mm thick insulation)

32 mm dia. (19 mm thick insulation)

25 mm dia. (19 mm thick insulation)

Motorised Butterfly Valves

Supply, installation, testing and commissioning of motorised on / off butterfly valves with modulating motor in return chilled & hot water line of each chiller & Hot Water Generator operated through BMS & of following sizes. Valves shall be insulated as per pipe insulation material & thickness given above.

200 mm dia (For Chiller)

100 mm dia (For Hot Water Generator)

Manual Balancing Valves

BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified.

200 mm dia (For Chiller)

100 mm dia (For Hot Water Generator)

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified

200 mm dia

150 mm dia

125 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified.

200 mm dia

Y-strainer ( With Insulation )

200 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

Pressure Gauges

Supply, installation, testing and commissioning of pressure guage of approved make of dia 150 mm conforming to tender specifications.

Thermometer

Providing & fixing in position the mercury in glass industrial type thermometers.

Condenser Water Piping

Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends, tees etc..but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect.

Note:-The Pipes size 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.

150 mm dia pipe

250 mm dia pipe

300 mm dia pipe

Motorised Butterfly Valves

Supplying, fixing, testing and commissioning of following sizes Motorized Butterfly Valve with CI Body, SS Disc, O - ring and minimum PN-16 pressure rating, conforming to BS 5155, IS 13095, with IP-55 actuator, capable of accepting upto 10V DC , and upto 20 mA electric signal and providing similar transduced feedback output to control system as required.

250 mm dia (For Condenser Out, Cooling Tower In & Out)

BUTTERFLY VALVE (MANUAL) with CI body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified.

50 mm dia

Thermometer

Providing & fixing in position the mercury in glass industrial type thermometers.

Pressure Gauges

Supply, installation, testing and commissioning of pressure guage of approved make of dia 150 mm conforming to tender specifications.

Rectangular GI Ducting

Rectangular GI Ducting (Factory Made - L Shape)

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.

24 G (Up To 750 mm)

22 G (751 to 1500 mm)

20 G (1501 to 2250 mm)

18 G (Above 2250 mm)

Site Fabricated GI Ducting

Supply, installation, balancing and commissioning of site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required

a) 24 G (Up To 750 mm)

b) 22 G (751 to 1500 mm)

c) 20 G (1501 to 2250 mm)

d) 18 G (Above 2250 mm)

Duct Accoustic Lining

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.

Fire Dampers & Actuator

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications.

Fire Damper

Actuator

Grilles, Diffusers, VCD

Supply, installtion and testing of Powder coated Aluminium extruded grills / diffusers as per specifications given in tender and of following sizes.

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.

GSS Duct Damper

Supply, installation and testing of multiblade box type Galvanized Sheet Steel construction damper for ducts to be provided with suitable links and quadrants for control of volume of air.

Acoustic Insulation of AC Plant Room / AHU Room

Supplying, fixing acoustic lining on wall and ceiling of AC Plant Room with 50 mm thick, density 32 kg/cu.m resin bonded glass fiber insulation friction fixed in 610 mm x 610 mm frame work made of 25X50X50X50X25 mm made out of 0.6mm thick GI sheet U shaped channel and covered with reinforced fiber glass tissue and finished with 0.80 mm perforated aluminium sheet etc. complete as required and as per specifications.

FIRE FIGHTING WORKS

FIRE PUMPS & HYDRANT WORKS

FIRE PUMPS - ELECTRICAL

Providing, Installation, testing & commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, grade 304, sheet with 3 mm dia holes with stainless steel flange.

250 mm dia

(A) Supplying, Installation, testing & commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respescts, as required: (Teearce Pump)

(B) Horizotal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS:1520

(C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase , 50 Hz, AC supply with IP55 class of protection for enclosure, horizontal foot mounted type with class-'F' insulation, confirming to IS-325

(D) M.S fabricated common base plate, coupling, coupling guard, fouldation bolts etc. as required.

(E) Suitable cement concrete foundation duly plastered and with anti vibration pads

450 LPM at 35M Head

900 LPM at 35M Head

Supplyin and fixing air vessel made of 250 mm dia, 8 mm thivk M.S sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure guage and painting with synthetic enamel point of approved shade as required:

Providing & fixing of pressure switch in M.S line including connection etc. as required.

Supplying and fixing single headed internal hydrant valve with instantaneous gunmetal/stainless steel coupling of 63 mm dia with cast iron wheel ISI marked confirming to IS 5290 (Type- A) with blank gummetal/stainless steel cap and chain as required:

Single headedd stainless steel

Supplying and fixing single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM gun meatl/Stainless steel coupling and cast iron wheel, ISI marked, comnfirming to IS 5290 (type-A) with blank gunmeatl/stainless steel cap and chain as required:

Single headedd stainless steel

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle confirming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:

Stainless steel (Grade 304)

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female coupling duly bound with GI wire, rivets etc. cionfirming to IS 636 (type- A) as required:

Stainless steel (Grade 340)

Supplying and fixxing first-aid hose reel with MS construction spray painted in post office red, confirming to IS 884 complete with the following as required

20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type- 2 as per IS: 12585

20 mm nominal internal dia gun metal globe valve & nozzle.

Drum and brackets for fixing the equipments on wall.

Connections from riser with 25 mm dia stop gum metal valve & M.S. pipe and socket.

Supplying & fixing orifice plate made out of 6 mm thich stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external & internal hydrants to reduce pressure at the outlet to the level of 3.5 Kg/Sqcm complete as required.

Supplying & fixing of the fire brigade connection of cast iron body with gun metal male instantaneous inlet coupling complete with cap and chain as required for suitable dia MS pipe connection confirming to IS 904 as required.

4 way - 150 mm dia M.S. pipe

2 way - 150 mm dia M.S. pipe

PIPING & VALVES FOR FIRE FIGHTING SYSTEM

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms,depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth,including consolidating each deposited layer by ramming, watering,etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Excavating trenches of required width for pipes, cables, etc including excavation for sockets,depth upto 1.5 m, including getting out the excavated matterials, returning the soil as requred in layers not exceeding 20 cm in depth including consolidating each deposited layers by by ramming, watering,etc. and stacking serviceable material for measurements and disposal of unserviceable matterial for measurement and disposal of unserviceable matterial as directed within a lead of 50m:

Ordinary rock

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Hard Rock

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Making 1:2:4 cement concrete supports and thrust blocks generally as per required and approved.

Constructing masonary chamber 90 x90 x100 cm. inside with 75 class designation brickwork in cement mortar 1:4 ( 1 cement : 4 fine sand) for sluice valve with CI surface box 100 mm top dia. 160 mm bottom dia. And 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1 :5 :10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size and inside plastering with 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design with FPS bricks

Providing, Laying, testing & commissionong of 'C' class heavy duty MS pipe confirming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coatar/asphalt taps as per IS 10221, refilling the trench etc. of following sizes complete as required.

150 mm dia

Supplying & fixing, testing & commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confirming to IS 13095 of follwong sizes as required:

80 mm dia

100 mm dia

150 mm dia

200 mm dia

Providing, Installation, testing & commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required:

200 mm dia

150 mm dia

80 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confriming to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges. Tappers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamal paint of required shade complete as required:

250 mm dia (wall thickness 6.3 mm)

200 mm dia (wall thickness 6.3 mm)

150 mm dia

100 mm dia

80 mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25 mm dia

SPRINKLERS SYSTEM

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

Pendent Sprinkler

Horizontal side wall sprinkler

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe confriming to IS 3589/IS 1239 including welding, fittings like elbows, tees, flanges. Tappers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamal paint of required shade complete as required:

150 dia MS pipe

100 dia MS pipe

80 dia MS pipe

65 dia MS pipe

50 dia MS pipe

40 dia MS pipe

32 dia MS pipe

25 dia MS pipe

ELECTRICAL WORKS

Earthing Strip / Wires.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

SCHEDULE ITEM (A)

Providing and laying light weight Foam Concrete of density 500 kg/cum in sunken portion at all levels as per direction of Engineer-In-Charge.

Providing and fixing of fully insulated Wooden fire rated doors as per BS:476 Part-20 & 22 & IS 3614 part-2 for stability, integrity and thermal insulation 03 Criteria Wooden door . Fire door shall be tested at CBRI, Roorkee for maximum rating of 2 hrs. Any deviation in specification other than what is mentioned in the test certificates are not allowed. Proper label confirming the type of door and the hourly rating is mandatory. Door leaf shall be minimum 50mm thick fully flush door, 50 mm thick shutter, comprising of 75mm x 44mm hardwood internal timber frame work, with infill of 96 kg / m3, ceramic fiber blankets, coated with VIPER FR intumescent coating on both sides for insulation . The coated intumescent coating on both sides for insulation. The coated insulation shall be sandwiched between minimum 12 mm thick PAMTECH/ROMATECH or equivalent make calcium silicate Boards on both sides (edge to edge or internal Hardwood frame) having a maximum density of 700 kgs/Cum, Cladded with 3mm Commercial Ply & 1 mm thick laminate (as per approved shade) on both sides of the shutter with 50mm x 14mm teak wood lipping all-round the shutter. The door frame will be made out of Hardwood (Red Mirandi) of maximum section 120 x 70mm and coated with VIPER or approved Fire reatrdent Primer. The rebate shall be of 20 mm x 53mm in the Door Frame to accommodate the shutter in frame. Both frame and shutter shall be fitted with 2 Nos of fire & smoke intumescent seal of approved make of size 10 x 4 mm on all the three sides of the Frame and 1 No. 20 mm x 4mm Fire Seal on Shutter except bottom. The pasting of the ply/laminate should be done using automatic machine and should be free from any nails or perforations. The door supplier should have tested their door within last 5 years at CBRI, Roorkee. all complete as per direction of Engineer-incharge

Providing & Fixing following fire rated fittings as per manufactures specifications and direction of the Engineer-In-Charge.

Door Locks

Glass ( Wired) Vision Panel Of Size 200mm X 300mm

Door closer

SS Door Handles

SS Tower Bolts

Panic bar for S/L door

External trim for panic bars

2000 Series Windows – Double Rebate Windows Providing & fixing of windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 48 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished item of work including of all taxes. (Make: A2Z Infra Solutions/ Elixir Metform Pvt Ltd./ Lakshmi Fabrications)

Granite work gang saw cut (polished and machine cut) of thickness 18mm for wall lining,skirting and dado (veneer work) in cement mortar 1:3 (1 cement : 3 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade: (To be secured to the backing by means of cramps, which shall be paid for separately).

Providing & Fixing of 8mm thick Rubber flooring Rolls with 15% EPDM & 85% SBR, Density (kg/m3):1000/1200, Hardness (Shore a):68, Stretch (MPA):2.2, Abrasion resistance: 0.0075g (ASTM‐D4060‐01), Rebound resistance: 55%, Friction coefficient: trends μs: 0.995 .trends μk: 0.930, Shape deformation: 42%, Length (m):10 ±5cm, Width (m):1m ±5mm, Thickness (mm): 8mm ±0.3mm etc.complete as per the direction of Engineer-in-charge.

Providing and applying special pure acrylic base resin stone texture paint ( finish thickness 1.2mm to 1.5 mm) Marmoplast of Ultratech make or equivalent . One coat of acrylic Primer Mixed with wall sealer in the ratio of 1:1 is applied with brush and roller. Repairs to be done with interior grade putty post primer application . One Coat of stone crushed texture to be applied as pitted finish applied with special tool (added with inorganic pigments from 0.01- 3.00%) after the final texture coat one coat of pure acrylic emulsion followed by final coat of siloxane base protection coat to be applied which make the product completely water repellent / dust resistant / antifungal which ensures with a warranty of 08 years on shades and sustainability ,whereas grooves are to be crafted in plaster as design approved by engineering in charge.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing S.S. 304 tower bolts ( 300 X10 mm Article Code no 911.81.585 Of Hafele or equivalent) with necessary SS screws etc.complete.

Providing and fixing S.S. 304 tower bolts (150 X10 mm Article Code no 911.81.576 Of Hafele make or equivalent) with necessary SS screws etc.complete.

Providing and fixing S.S. 304 D Type pull Handle 300 X22 mm ( Article Code no 903.11.470 of Hafele make or equivalent) with necessary screws etc. complete .

D Type pull Handle 300 X22 mm

Providing and fixing Double Rod hanging floor door stopper ( Article Code no 938.66.000 Hafele or equivalent ) of brass metal in SS Finish with necessary screws etc. complete.

Providing and fixing stainless steel Hydraulic door closer ( Article Code499.30.002 of Hafele or equivalent) , door weight up 80 kg with necessary accessories and screws etc. complete.

Providing and fixing S.S. 304 sliding door bolts ( 300 mm Product Code no 4033 of Godrej & Boyce Mfg make or equivalent ) with nuts and screws etc. complete : 300x16 mm

Providing and fixing S.S. 304 sliding door bolts ( 250 mm Product Code no 4032 of Godrej & Boyce Mfg make or equivalent ) with nuts and screws etc. complete : 250x16 mm

Add for extra 2 nos grooves in granite treads size of 5mm X 10mm as per direction of Engineer in Charge.

Supply and installation of PVC flooring of 1.83m wide, having a nominal total thickness of 2.2mm. The nominal thickness of the wear layer would be 2 mm. The product should have a conductive backing of 0.2mm. The wear surface shall consist of impregnated polyurethane homogeneous mixture of PVC, Plasticizers, Urethane, color pigments and filler calendared to form a sheet. Colors and pattern detail shall be dispersed throughout the thickness of the wear layer. It shall conform to Group P of Wear Resistance as per EN 649, Flammability of class Bfl-s1 as per EN 13501-1, Slip resistance of R9 as per BGR 181, Dynamic Coefficient of friction as DS as per EN 13893, Impact sound reduction of 3 dB as per EN ISO 140-8, Residual indentation of 0.05 mm as per EN 433, Color fastness rating ≥6 as per ISO 105-B02, Vertical resistance(R1) less than 106Ω as per EN 1081, Static electrical charge of ≤2.0kV as per EN 1815, Thermal resistance of 0.01m²K/W as per EN 12667, Thermal conductivity of 0.25 W/mK as per EN 12524. PASTELL conductive shall exhibit ESD properties as following - Vertical resistance less than 3.5x10^6Ω as per EN 61340-4-1, Static electrical charge - system test less than 100V as per EN 61340-4-5.The class of use of is 23/34/43 as per EN 685.

Installation: It is important to ensure the sub floor on which the sheet is being laid is smooth, flat & hard & free from moisture,grease, etc. In case of uneven sub floor the same should be leveled by self leveling compound. IPS/Vitrified/ceramic/mosaic tiles do not provide zero leveled sub floor.The moisture level present in the subfloor should be less than 8% before installation of the floor. The sheet should be laid using adhesive recommended by Armstrong. Each row of tiles/strip of floor covering must be linked crosswise with a continuous copper strip. Individual rows/strips must be at least 3 m² in size and linked to the rest of the area with a copper tape. In rooms of up to 40 m², connection points for equipotential bonding should be provided in at least one point in the room. In larger rooms, several connection points must be used. The installation shall be undertaken as per the manufacturer’s installation instructions

Supply and installation of PVC Sheet wall covering manufactured by Armstrong World Industries, Inc, 1.5m wide, having a nominal total thickness of 1mm. The nominal thickness of the wear layer would be 1.25mm. The wear surface shall consist of impregnated polyurethane homogeneous mixture of PVC, Plasticizers, Urethane, color pigments and filler calendared to form a sheet. Colors shall be dispersed throughout the thickness of the wear layer. Wallflex shall conform to Group M of Wear Resistance as per EN 660-2, Fire resistance of group 2 as per AS/NZS3837, Residual indentation of ≤0.10mm as per EN433, curling after exposure to moisture ≤8mm as per EN434, Seam strength of mean≥240N/50mm as per EN684.

Providing of 2 - 3 mm average thick layer of cementations smoothening compound of UZIN NC 149 sh or equivalent as recommended by the Vinyl sheet flooring manufacturer over and including a priming compound of UZIN PE 360 sh or equivalent as recommended by the Vinyl sheet flooring manufacturer and installation team on concrete surface to provide a smooth & homogenous surface for laying of vinyl sheet flooring complete to the entire satisfaction of Engineer-in-charge

Providing and fixing 230mm X 75mm X 15mm size of Clay tiles work for wall lining with special adhesive like Araldite or equivalent over 10mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement with an admixture of pigment to match the stone shade.

Providing and fixing 230mm X 75mm X 15mm size of Clay tiles work for wall lining with special adhesive like Araldite or equivalent over 10mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement with an admixture of pigment to match the stone shade.

SUPPLY AND FIXING OF 4MM THICKNESS POLYCARBONATE SOLID SHEETS WITH BOTH SIDE 50 MICRONS UV CO-EXTRUSION IN 4MM THICKNESS OR ABOVE, COLOUR AS APPROVED. THE COMPACT SHEETS SHALL BE 1220MM WIDE & LENGTH NOT MORE THEN 3050MM /4000MM/ 15250MM/ 33500MMAND IS TO BE FIXED WITH ALUMINIUM PRESSURE PLATES WITH EPDM RUBBER TO ENSURE WATER TIGHTNESS AND MAXIMUM UPLIFT CAPABILITY. THE WEIGHT SHALL NOT BE LESS THAN 4.80 KGS PER SQ.MTR. THE COMPACT SHEETS SHOULD BE PLAIN ON BOTH SIDES AND MANUFACTURED FROM PRIME GRADE PC RESINS. MANUFACTURER TEST CERTIFICATE SHALL BE PROVIDED FOR SUPPLIES MADE.” Complete as per direction of Engineer-In-Charge.

Providing and fixing 230mm X 75mm X 15mm size of Clay tiles work for wall lining with special adhesive like Araldite or equivalent over 10mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement with an admixture of pigment to match the stone shade.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealant shall be paid separately) Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Providing and fixing unperforated corrosion resistant Aluminium Magnesium alloy lineal metal panel ceiling system by Hunter Douglas/Armstrong/ Saint Gobain or Equivalent of approved wood Finish colour consisting of panel 180mm wide x 15mm deep x 0.6mm thick with square edges, panel length up to 6 mtrs, Coil Coated on a Continuous Paint Line, Double baked and roll formed from doubled baked enameled corrosion resistance aluminium magnesium alloy for higher strength and good roll forming characteristics. Panel shall be clipped to a baked enameled aluminium panel carrier of 62mm wide x 29mm deep made of 0.90 mm thick in standard length of 5 mtrs made of doubled enameled aluminium magnesium alloy black with cut outs to hold the panels in a module of 200 mm and at a distance 1.45 mtrs without insulation. The carrier shall be suspended by means of G.I suspension rod 4mm diameter and a Galvanized suspension spring clip at a distance of 1.7mtrs centre to centre.All complete as per drawings, specification and direction of the Engineer in Charge. All Ceiling products shall adhere to Green Pro Certification Paint finish: Aluminium panels shall be chromatised for maximum bond between metal and paint enamelled twice under high temperature, one side with full primer and finish coat, the other side (inner side) with a primer coating and skin coat on a Continuous Paint Line. Mode of Measurements: Measurements shall be wall to wall without any deductions for lights, diffusers, columns etc. Wood finish

Flotex Carpet (Area- Conference , Auditorium) Providing & Fixing of Flocked textile floor covering of Nylon 6.6 face fiber or equivalent of approved make with 100% Nylon and completely water proof resilient backing. The flooring should be Anti static with thickness of 4.3 mm and approximate weight of 1.8 k.g./sqm of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sq.mtr (70 million fiber/sq.yd) in the width of 2 mtr .The floor covering should have Fire Test EN-13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 Class DS, SANITISED anti-microbial treatment, with resilient waterproof backing, anti allergic which is certified by British allergy foundation, with ten year replacement guarantee. The carpet should have permanent static control & should be fixed with powder coated aluminum angles as per detail. Aluminum angles to be paid separately. The work should be carried out by the authorized installer of the Company in India.

Providing & Fixing 3 mr Automatic Boom Barrier with Wireless Remote Control as per manufacurere specifications and direction of engineer-in-charge.

Providing , Fixing, testing and commissioning of CP Brass 115mm long Shower Arm with wall flange and pressure adjustable Shower Rose complete with all accessories as required and making good the walls wherever required. (MAKE-CERA -Model No-F7040101 FOR SHOWER ARM & CERA MAKE FOR HEAD SHOWER F7020301 or EQUIVALENT.)

Providing and fixing 8mm thick beveled edge glass mirror with side polished complete including fixing over marine plywood frame work with silicon at all levels & height including fixing of molded ,screw and silicon etc. incl labors, tools, scaffolding at all heights as per Direction of EIC .

Providibng and fixing straight type Macfit single body push fit type WC pan connector with factory supplied spring loaded seal guard of McAlpine, UK with integral single mould sealing fins made of flexible EVA body, including bush/adaptor for use with C.I. Pipe as supplied with the pan connector.

Providing and fixing CP brass single lever low flow wall mounted Sink mixer with 15 mm CP brass single lever swivel spout with waste complete including cutting and making good the walls where required.(1) Kerovit make (Model -KB211024-CP). (2)Hindware Make(Model-F230014) Rs.=5640. (3) Parryware Make(Model-T1635A1)Rs.=6800

Providing & Fixing of Grab Bar size 300mm long in handicap toilet complete as required.Makes & Model No.Jaquar AKP-35701P.

Providing & fixing glass urinal partition of Height: 900mm,Width: 450mm &Frosted Safety Glass: 8 mm with fixed with expandable anchor fasteners with C.P. brass bolts and washers, embedded in wall with anchor and set in cement concrete complete including cutting and making good the walls wherever required .(1) (MAKE-JAGUAR: MODEL NO-Model No. 1810-US, 1810-UC.)(2)Hindware Make(Model-61001) Rs.=3500.

Providing,Fixing satin finish stainless steel AISI 316 grade wall mounted coat hook on door complete. Jaquar make CAT No- AKP-35791P (2)Hindware Make(Model-Robe Hook F870007) Rs.=1216.

Providing & fixing brass ball valve with hard chrome plated ball inside PTFE (Teflon) seat & ring with chrome plated centre handle with female BSP threads complete:in all respects.

15 mm dia

100 mm dia, nominal bore

Fixing of Storage type water heater/ Geyser with required accessories like 15 mm CP angle valve on inlet , heavy duty reinforced flexible PVC connector for cold water line and flexible CP brass connector with CP checkout for hot water line, CPVC line connection, MS bracket with two coats of enamel paint, anchor fastners etc to hang the units, providing and fixing of 16 A 3 Pin plug of Anchor make, etc complete as required.

Capacity 25 Liters

Providing and fixing sound insulated Polyproplene piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe = 1.25gms/cm3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with all necessary fittings in blue colour, fitted with factory fitted lip ring incluiding painting with ordinary cement based paint for external installation.

Providing and fixing sound insulated Polyproplene piping system with 3 layer pipe fittings, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA ,with all necessary fittings , fitted with factory fitted lip ring incluiding painting with ordinary cement based paint for external installation. (POLOPLAST - PKNG, RAUPIANO PLUS).

Tee 90degree 110 mm dia.

Tee 45degree 110 mm dia.

Providing and fixing terminal guard 100mm standard PP

Providing and fixing terminal guard 100mm standard PP

Providing and fixing PP white Trap with minimum 50mm water seal with rubber seal on inlet to push fit hopper for indirect waste connections (McAlpine, UK) or equivalent.

110 mm inlet & 110 mm outlet.

Providing and fixing sound insulated Polyproplene piping system with 3 layer pipe, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA with all necessary fittings, fitted with factory fitted lip ring.(POLOPLAST - PKNG), RAUPIANO PLUS , HULIOT or equivalent).

160 mm bend

160 mm Shoe

Providing and fixing G.I. Inlet fitting of suitable size with 2 & 3 Nos. G.I. Socket 32 & 40 welded G.I. pipe and dipped in hot bitumen complete in all respect.

100 mm diameter pipe (Hopper)

Providing and fixing floor drain made of 100 x 50 dia elbow / tee as applicable connected with 50 dia GI pipe painted with primer, two coats of black bituminastic paint,wrapping 1 mm thick PVC tape and final coat of black bituminastic paint B109 complete in all complete including cutting and making good the walls and floor wherever required

Providing and fixing flanged cleanout plug with M.S. flanged tail pieces, blind flang, 6mm dia nut & bolts, gasket and washers fixed to C.I. Pipe with drip seal joint complete in all complete including cutting and making good the walls and floor wherever required

with 100 mm dia. Pipe

Providing & fixing of epoxy coated 25 mm thick C.I. Grating with frame for channel drains including all accessoreis complete

WATER SUPPLY INSTALLATIONS

Providing stainless steel pipes conforming to EN 10312 standard complete with press type fittings for Hot and cold water supply, RO & domestic water supply system capable to withstand temperature upto 1100 centigrade and pressure upto 16 bars made from 316 L grade-Material no. 1.4404 (X2CrNiMo17-12-2) of annealed and pickled stainless steel sheet, with ends deburred at 900 and with length of 3 meters. Pipe qualifying to 100% eddy current, 100% hydrostatic tested and air-under water tested under 10kgs. Fittings also conforming to EN 10312 standard in 316 L stainless steel grade of approved make in accordance with DVGW regulation such as tees, coupling, elbow, male adapter, connectors etc with Black grooved O-ring of EPDM material which can withstand temperature upto -200 to 1100 C including suitable connection as per site requirement. Direct contact of stainless steel pipes and fittings to galvanized iron should be avoided by inserting approved type of filler material as per project manager’s/consultant requirement. Flanges, clamps with hanger at a spacing of 2 m centre to centre min or as required etc. necessary adapters for GI/copper and CP fittings, jointing, sundries, cutting holes in walls/floors/slabs & making good complete. (JINDAL,VEIGA,ALFA)

18 mm dia, nominal bore

22 mm dia, nominal bore

28 mm dia, nominal bore

35 mm dia, nominal bore

42 mm dia, nominal bore

54 mm dia, nominal bore

76 mm dia, nominal bore

89 mm dia, nominal bore

108 mm dia, nominal bore

40mm nominal outer dia. Pipes.

Cost of drilling 200mm x150mm x230 meter deep bore well in all kind of soil and rock in rural or any other area for installation of pump sets with hydraulic DTH Rig machine all complete including supplying all materials tools drilling rig and air compressor and equipments, as well as fuel lubricant transportation of Rig machine and other vehicles upto the site including cost of flusing charges, geological investigation etc all complete.

(i) From 0-50 meter

(ii) From 50 - 200 meter onwards

Providing and fixing insulation with thermaflex elastomeric nitrile rubber sheets complete with plastering of 20 mm thick insulation with thermaflex elastomeric nitrile rubber sheets for hot water & cold water pipes exposed to sun complete with Aluminium.

15 mm dia, nominal

20 mm dia, nominal

25 mm dia, nominal

32 mm dia, nominal

40 mm dia, nominal

50 mm dia, nominal

65 mm dia, nominal

80 mm dia, nominal

Providing and fixing brass automatic air vent at the top of each riser.

25mm diameter

Providing and fixing MS pipe puddle flanges of required size with 6mm thick MS plate of required size of suitable size properly fixed in RCC walls of water & Fire tanks, including necessary welding as per details shown on darwings and directions of Engineeer-in-charge for water tanks.

25mm dia pipe, 600mm long with 6 mm MS plate of size 250mm dia

32mm dia pipe, 600mm long with 6 mm MS plate of size 250mm dia

40mm dia pipe, 600mm long with 6 mm MS plate of size 250mm dia

50mm dia pipe, 600mm long with 6 mm MS plate of size 300mm dia

80mm dia pipe, 600mm long with 6 mm MS plate of size 300mm dia

100mm dia pipe 600mm long with 6 mm MS plate of size 400mm dia

150mm dia pipe, 600mm long with 6 mm MS plate of size 400mm dia

200mm dia pipe, 600mm long with 6 mm MS plate of size 600mm dia

250mm dia pipe, 600mm long with 6 mm MS plate of size 600mm dia

65 mm dia, nominal bore

80 mm dia, nominal bore

100 mm dia, nominal bore

Cost of drilling 200mm x150mm x230 meter deep bore well in all kind of soil and rock in rural or any other area for installation of pump sets with hydraulic DTH Rig machine all complete including supplying all materials tools drilling rig and air compressor and equipments, as well as fuel lubricant transportation of Rig machine and other vehicles upto the site including cost of flusing charges, geological investigation etc all complete.

Cost of drilling 200mm x150mm x230 meter deep bore well in all kind of soil and rock in rural or any other area for installation of pump sets with hydraulic DTH Rig machine all complete including supplying all materials tools drilling rig and air compressor and equipments, as well as fuel lubricant transportation of Rig machine and other vehicles upto the site including cost of flusing charges, geological investigation etc all complete.

Providing and fixing 80mm dia GI pipes to IS:1239 heavy class with fittings.

Supply, Lowering, installation & testing of submersible pumping set with 10 HP motor 4 stage pump suitable for 20/26/30/38/40/45/50 m3 hr. at 42/38/36/32/29/25/20 mtr. Head respectively. With Three Phase. (Model: 273/4)

Providing & fixing cable 3CX 6 sq.mm. From submersible pump to panel board of Aluminium cable.

Providing & fixing Panel Board for submersible pump fitted with DOL starter ammeter, voltmeter single phase preventer standard/indo/cop make MCB of off switch push bottom duly wired and made out of 16/18 SWG sheet.

Providing and fixing lever operated butterfly valve conforming to IS:13095-91 PIN 1.6 including necessary companion flanges, bolts and nuts complete.

80mm dia

Providing and fixing C.I. Wafer type flanged non-return valves with bolts, nuts, washers & companion flanges complete.

80mm dia

PUMPS & ALLIED WORKS

Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel-304 body, Stainless steel-304 impeller, Stainless steel-304 casing, shaft of Stainless steel-316 and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information.

Filter Feed Pump ( Dom. Water)

Set of Three Pumps( 2 Working+ 1 Standby)

Capacity 450 LPM

Head 35 M.

HP 7.5 HP ( Approx.).

Filter Feed Pump ( Dom. Water)

Set of Two Pumps( 1 Working+ 1 Standby)

Capacity 4 LPS

Head 35 M.

HP 2.0 HP Approxi.

Water Make up Pump to STP & Irrigation Pumps

Set of Two Pumps( 1Working+ 1 Standby)

Capacity 200.0 LPM

Head 30 M.

HP 5.0 HP ( Approx.).

Irrigation Pumps

Set of Two Pumps( 1 Working+ 1 Standby)

Capacity 1.0 LPS

Head 30 M

HP 2HP Approxi.

Soft Water Transfer Pumps at STP Pump Room

Set of Two Pumps( 1 Working+ 1 Standby)

Capacity 250.0 LPM

Head 20 M

HP 5.0 HP ( Approx.).

Supply, Installation, Testing And Commissioning of Compact Self Contained Skid Mounted Hydropneumatic System As Follows:(A) Vertical, In-Line, Multisage, centrifugal pumps with SS-304 casing and impeller and SS-316 shaft, CI base & head CI material shouldbe CED coated TEFC motor (with mechanical seal) with single VFD suitable for automatic operation and delivering the specified discharge at the specified head,VFD should be of class IP-20 with pressure vessel, pressure vessel should be matching of specied requirement of pump.(B) b. External Pump mounted or wall mounted microprocessor PID controller and frequency inverter integrated in a single body or as separate components with pressure sensor transmitter minimum two lined LCD display, diodes to indicate pump ready, pump running and fault and capable to communicate with other controllers following MODBUS-RTU or BACNET Class-2 protocall through RS485 port. System should be capable to compensate for frictional losses at lower flows. All alarms should be displayed in the controller. System should be equiped with dry running protection. ( C) Complete (Skid mounted wall mounted / floor mounted) electrical control panel comprising of all accessories such as PLCs, pressure switches, pressure transducers, control wiring and any other necessary imports etc. (list to be provided by the vendor) (D)Precharged diaphram pressure vessel with food grade membrane, charging connection, connected to outlet header with necessary flanges, gaskets, isolating valves, nuts/bolts etc complete.(E)Set of accessories such as pressure switches, pressure transducers, inter connecting power and control cabling etc. complete(F) Accessories like pressure gauge, MS base frame (Synthetic enamel painted over a coat of primer)(G) GI suction and delivery header with flanges for inlet connection, common outlet header with flanges for outlet connections as required, and inter connecting piping with flexible connections, eccentric type reducers etc. all necessary indigenous accessories like valves, strainer & NRV as required to complete the installation.

Domestic Water hydropneumatic Pumps(For Hospital & College Blocks)

Set of Three Pumps( 2 Working+ 1 Standby)

Capacity 250.0 LPM

Head 65 M

HP 10 HP ( Approx.).

Domestic Water hydropneumatic Pumps(For Residential blocks)

Set of Three Pumps( 2 Working+ 1 Standby)

Capacity 200.0 LPM

Head 65 M

HP 10 HP ( Approx.).

Domestic water supply transfer pumps

No. of pumps 3 (2 Working + 1 Standby): 1 set

Water Flow Rate 4.0 LPS each

Head : 50 M

Min. Motor HP : 3.0 H.P. (Each)

Flushing Water hydropneumaticPumps at STP Pump Room

Set of Two Pumps( 1 Working+ 1 Standby)

Capacity 150.0 LPM

Head 65 M

HP 6.0 HP ( Approx.).

Flushing Water supply transfer pumps

No. of pumps 2 (1 Working + 1 Standby): 1 set

Flow Rate : 4.0 LPS each

Head : 50 M

Min. Motor HP : 2.0 H.P. (Each)

Domestic Water booster Pumps at Terrace(For Boys & Girls Hostel)

Set of Three Pumps( 1 Working+ 1 Standby)

Capacity 150 LPM

Head 20 M

HP 2.5 HP ( Approx.).

Domestic Water booster Pumps at Terrace(For Nurse Hostel , Tpye-III , PRA & Guest House)

Set of Three Pumps( 1 Working+ 1 Standby)

Capacity 175 LPM

Head 20 M

HP 2.5 HP ( Approx.).

Domestic Water booster Pumps at Terrace(For Resident Doctor & Tpye-IV )

Set of Three Pumps( 1 Working+ 1 Standby)

Capacity 200 LPM

Head 20 M

HP 2.5 HP ( Approx.).

Domestic Water booster Pumps at Terrace(For Interns Hostel-Male & Female & Tpye-V and Sadar Hospital )

Set of Three Pumps( 1 Working+ 1 Standby)

Capacity 250 LPM

Head 20 M

HP 2.5 HP ( Approx.).

Supply, installing, testing and commissining of submersible single stage single entry pumps with C.I.body and C.I. two vane enclosed type impeller connected to TEFC submersible motor for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphram and bend, vertical discharge pipe, guide pipe and chain in built level controller, sequence running controller, dry running Protection complete in all respects. Complete With media saturation arrangement twin lobe rotary air blower with motor , base frame , pulleys , v belts, drives guard suction pipe , accessories, painting, testing and commissioning complete with approved quality and make as required as per instruction of site incharge.

(Pumps shall be installed in a set of two pumps One working and One standby)

Water Supply Pump Room & basement drainage

(Pumps to be suitable to handle solids upto 12 mm size)

Capacity - 5.0 LPS (Each)

Head - 10 M

H.P. - 3.5 HP Approx.

Sewerage Sump Pump at STP area

(Pumps to be suitable to handle solids upto 40 mm size)

Capacity - 5.0 LPS (Each)

Head - 10 M

H.P. - 5.5 HP Approx.

Providing stainless steel pipes conforming to EN 10312 standard complete with press type fittings for Hot and cold water supply, RO & domestic water supply system capable to withstand temperature upto 1100 centigrade and pressure upto 16 bars made from 316 L grade-Material no. 1.4404 (X2CrNiMo17-12-2) of annealed and pickled stainless steel sheet, with ends deburred at 900 and with length of 3 meters. Pipe qualifying to 100% eddy current, 100% hydrostatic tested and air-under water tested under 10kgs. Fittings also conforming to EN 10312 standard in 316 L stainless steel grade of approved make in accordance with DVGW regulation such as tees, coupling, elbow, male adapter, connectors etc with Black grooved O-ring of EPDM material which can withstand temperature upto -200 to 1100 C including suitable connection as per site requirement. Direct contact of stainless steel pipes and fittings to galvanized iron should be avoided by inserting approved type of filler material as per project manager’s/consultant requirement. Flanges, clamps with hanger at a spacing of 2 m centre to centre min or as required etc. necessary adapters for GI/copper and CP fittings, jointing, sundries, cutting holes in walls/floors/slabs & making good complete.

54mm dia

76mm dia

89mm dia

108mm dia

Providing and fixing cast iron wafer type butterfly valves (PN-10) complete with 2 nos. matching flanges (Table-E),bolts, nuts, 3.0 mm thick insertion neoprene gasket.

50mm dia

65mm dia

80mm dia

100mm dia

Providing and fixing of cast iron dual plate wafer type check valves (PN-10) including 2 nos. matching flanges ( Table-E), nuts, bolts, 3.0 mm thick thick insertion neoprene gasket.

65mm dia

80mm dia

100mm dia

Providing and fixing resilient rubber neoprene lined style arch vibration eliminators suitable for raw water upto 45 deg.C. Temperature working pressure upto 8 Kg/Sqcm.

50mm dia

65mm dia

80mm dia

Providing and fixing heavy duty armoured cables 1.1 KVA grade including necessary support clamps at ceiling level and connection lugs complete in all respects.

Power cable Copper 3 core 10 sq.mm

Power cable Copper 3 core 6 sq.mm

Power cable Copper 3 core 1.5 sq.mm

Providing and fixing CI Y type suction strainer with gunmetal or brass internal parts installed outside water tanks.

100 mm dia.

150 mm dia.

Supplying, installing, testing and commissioning controllers with low volatage relays, stainless steel probes and PVC shroud wiring from tank top to probles of required.

For Filter Feed Pump:

To start pump when water level is low in U.G. tank (Domestic water) and shut off pump when U.G. tank (Domestic) is full. Also to stop when water level is low in raw water underground tank.

For Sump Pumps:

To start pump when water level is high in sump and shut off pump when sump is empty. Both pumps are start when sump is over flowing.

For Over Head Tanks:

To start pump when water level is high in sump and shut off pump when sump is empty. Both pumps are start when sump is over flowing.

Providing and fixing galvanized slotted cable trays supported from ceiling at intervals of 60 cms on both ends including cable clips with nuts and bolts welding of support rods with ceiling inserts or by drilling and installing expandable fasteners, cutting and making good complete

300 mm wide (for horizontal at ceiling level)

150 mm wide (For vertical drops)

Providing and laying G.I. "C class" pipes and fittings conforming to IS: 1239 (Heavy class) Jointing with flanged joints including nuts & bolts, 3.0 mm thick compressed asbestos gasket etc, including with fittings, union and clamps including cutting holes in wall, makes chases in wall and making good the same in cement mortar 1:2 (1cement : 2 coarse sand) as directed by Project Manager complete in all respects.

50mm dia

65mm dia

80mm dia

100mm dia

150mm dia

Painting of G.I. pipes with two or more coats of synthetic enamel paint of approved quality over a coat of red oxide zinc chromate primer as directed by the Engineer-in-Charge (shade as per pipe colour code).

50mm dia

65mm dia

80mm dia

100mm dia

150mm dia

ELECTRICAL PANEL WORKS

MCC –1 for Plumbing system

Incoming

100 amps TPN MCCB with the following accessories:

c. Phase indicating lamps protected by 2 amp SP MCB 3 Set

Bus Bar

150 amps TPN aluminium bus bar with heat shrinkable insulation sleeves.

Outgoings

e. Spare MCB’s of following capacities:

i. 32 amps TPN MCB’s 3 No.

ii. 20 amps TPN MCB’s 3 No.

f. Necessary cable alleys, internal wiring, and interlocking, earthing for all equipment shall also included

Notes :

a. All MCCBs shall be of 35 KA breaking capacity and suitable for motor duty application.

b. Provision shall be made for providing potential free contacts to all pumps starters for connection to BAS

c. Provision shall be made to ensure system protection from dry running of the pump

MCC - 1 For Plumbing System as described above.

WATER TREATMENT EQUIPMENTS

Supply Installation,Testing & Commissioning of vertical self supporting Dual Media Filter fabricated from MS sheet as per IS: 2825, (minimum thickness of shell & Dish ends as per manufacturer design) pressure gauges, sample cock, GI class 'C' face piping, CI butterfly valves and all accessories , with initial charge of filter media including anthracite, painting inside with epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint, testing and commissioning complete.

For Domestic Water Supply

Capacity- 48000 LPH

Filtration rate- 14000 LPH/M2

Filter Dia approx. - 1750 mm (Approx.)

Working pressure: 3.0 Kg/sq cm.

Test pressure : 4. 5 Kg/sq cm

For Domestic Water Supply

Capacity- 7200 LPH

Filtration rate- 14000 LPH/M2

Filter Dia approx. - 1200 mm

Working pressure: 3.0 Kg/sq cm.

Test pressure : 4. 5 Kg/sq cm

Supply Installation,Testing & Commissioning of vertical self supporting Activated Carbon Filter fabricated from MS sheet as per IS: 2825, (minimum thickness of shell & Dish ends as per manufacturer design) pressure gauges, sample cock, GI class 'C' face piping, CI butterfly valves and all accessories , with initial charge of filter media including anthracite, painting inside with epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint, testing and commissioning complete.

For Domestic Water Supply

Capacity- 48000 LPH

Filtration rate- 14000 LPH/M2

Filter Dia approx. - 1750 mm

Working pressure: 3.0 Kg/sq cm.

Test pressure : 4. 5 Kg/sq cm

For Domestic Water Supply

Capacity- 7200 LPH

Filtration rate- 14000 LPH/M2

Filter Dia approx. - 1200 mm

Working pressure: 3.0 Kg/sq cm.

Test pressure : 4. 5 Kg/sq cm

Supply Installation,Testing & Commissioning of metering pump type chemical doser with 100 lits. HDPE solution tank,injection fitting assembly,suction and delivery hose upto the point of injection, capacity 0-6 lph, complete in all respects.

Chlorination of Domestic Water

Providing, fixing, testing & commissioning of MSEP water softening plant (suitable for 3 Kg/Sqcm working pressure) complete with initial charge with T-40 NA Resin, multiport valve with built in ejector for controlling all operations), regeneration system and HDPE tank, pressure gauge at inlet, outlet and back wash (each with isolation cock), valves, fittings and water hardness testing kit & associated works. Softener shall be suitable for the following duty:

Raw water hardness 500 Mg/L

Treated water hardness 100 Mg/L

Regeneration Period 10 Hrs.

Capacity : 2.06 LPS

SOLAR WATER HEATERS

Solar Water Heating System-500 LPD

Providing and fixing Solar Hot Water indirect Heating System using heating liquid medium comprising of flat plate solar panels, including all interconnecting insulated G.I. piping, primary and secondary recirculation pumps, pressure type insulated hot water tank, , outlet, Y stainer and a water meter on the inlet, air release valve all mounted on galvanized MS sections complete with connection with the existing piping. Comparising of following:-

Five Nos of. flat plate solar collector panels of 8 Sqm size approx. the panels enclosed in insulated collector boxes with single piece toughned glass 4 mm thick and fixed with heat resistant gasket.

One No. Integrated heat exchanger with drain down vessel 9 Ltrs. Capacity,designed so as to provide heat exchange between solar collectors and 500 ltr tank complete with drain down tank. The cold water heated after passing through heat exchanger to be stored in hot water tank. Necessary pumps and controller for automatic operations to be provided. including MS painted frames for the same.

M.S Horizontal hot water mixing tank of 500 ltr capacty shall be made out by of 4mm thick M.S. plate and inside lining of 1.0 mm thick stainless steel grade 316 sheet , out side steel primer including 50 mm thick glass wool slab insulation (density of glass wool 64 Kg/Sqm.) & 24 SWG aluminum sheet cladding outside the tank. Tank shall be provided with flanges for inlet outlet, over flow/ drain connection & Vent pipe with M H cover of 450 mm internal dia., Temperature and pressure release valve should be on top of water storage tank All the valve & accessories shall be suitable for an operating pressure of 6.0 kg/sqm including electric back up of 1 x 4.5 KW

Primary circulation pump 2 Nos (1W+1S) for circulation of fluid from Solar panels to heat exchanger.

Secondary circulation pump 2 Nos (1W+1S) for circulation of fluid from heat exchanger to hot water mixing tank.

One Lot of Inter-connected insulated G.I. piping insulated with 9 mm thick nitrile rubber heat resitant insulation sections ( Vidoflex or equiv.) and valves with outer mechanical protection of aluminium sheet cladding.

Solar Water Heating System as Describe Above

Supply , instalation, testing & commissioning of Cubical type branch distribution boards( BDB) of the following types made out of 14 gauge (2 mm thick) CRCA sheet complete with the accessories i/e. interconnections with suitable copper solid strip connections 100 A & above and with copper wires below, painting etc. and complete with supplying & fixing the following boardsetc. as required.

Branch Distribution Board for 8x500 LPD System

1 No. 125 AMP rating TP Modulded case circuit breakers with neutral link, front operated handle & thermal magneticrelease (35 Ka)

1 Set 125 Amp 4 Bars Tinned Cu. Bus Bar

1 Set LED type Indication lights

1 No. Digital Voltameter (0-500 V)

1 No. Digital Ammeter (0-125 A )

1 Set CTs for Ammeter 125/5 A ratio

3 Nos. 2 A SPMCB

Outgoing

08 Nos 25 A TP MCB , 10 KA (6+2 Spare)

03 Nos 63 A TP MCB , 20 KA for Electric back up supply.

The System is based on temprature difference and the system will operate automatically based on thermostat for startup and shutdown of Primary,Secondry, Receiculation pump and Heating elements on temprature differential.

Electric Panel as Describe Above.

Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel-304 body, Stainless steel-304 impeller, Stainless steel-304 casing, shaft of Stainless steel-316 and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information.

Hot Water Recirculation Pumps

Set of two pumps (1 Working + 1 Standby)

Capacity - 10 LPM

Head - 12.0 Mtr.

H.P. - 1.0 HP (Approx.)

Solar Hot Water Recirculation Pumps

Set of two pumps (1 Working + 1 Standby)

Capacity - 5 LPM

Head - 12.0 Mtr.

H.P. - 1.0 HP (Approx.)

Five Nos of. flat plate solar collector panels of set of 8 Sqm size approx. the panels enclosed in insulated collector boxes with single piece toughned glass 4 mm thick and fixed with heat resistant gasket.

VALVES AND FITTINGS IN HOT WATER MIXING TANK

65 mm PN10 Butterfly Valve. Cold water inlet

65 mm PN10 Butterfly Valve. Hot water outlet

65 mm PN10 Butterfly Valve. For drain

50 mm PN10 Butterfly Valve. For return line hot water

40 mm PN10 Ball Valve. For heat pump inlet and out let

Safety valve size 25 mm

Pressure gauge(0-10 kg/cm2, 4 inch dial with valve

Temp. gauge(0-100 Deg. C, 4 inch dial (Thermo well type)

Y-Strainer 40 mm C.I. heat pump inlet

Check Valve CI 65 mm cold inlet line

NRV40 mm HEAT PUMP hot water line

Supply, installation, testing & commissioning of heavy duty PVC insulated copper armoured cables suitable water submerged condition, 1.1KVA grade including necessary support clamps, complete in all respects.

3 x 2.5 sq. mm

3 x 6 sq. mm

EXTERNAL WATER SUPPLY & IRRIGATION SYSTEM

Providing stainless steel pipes conforming to EN 10312 standard complete with press type fittings for Hot and cold water supply, RO & domestic water supply system capable to withstand temperature upto 1100 centigrade and pressure upto 16 bars made from 316 L grade-Material no. 1.4404 (X2CrNiMo17-12-2) of annealed and pickled stainless steel sheet, with ends deburred at 900 and with length of 3 meters. Pipe qualifying to 100% eddy current, 100% hydrostatic tested and air-under water tested under 10kgs. Fittings also conforming to EN 10312 standard in 316 L stainless steel grade of approved make in accordance with DVGW regulation such as tees, coupling, elbow, male adapter, connectors etc with Black grooved O-ring of EPDM material which can withstand temperature upto -200 to 1100 C including suitable connection as per site requirement. Direct contact of stainless steel pipes and fittings to galvanized iron should be avoided by inserting approved type of filler material as per project manager’s/consultant requirement. Flanges, clamps with hanger at a spacing of 2 m centre to centre min or as required etc. necessary adapters for GI/copper and CP fittings, jointing, sundries, cutting holes in walls/floors/slabs & making good complete with including trenching and refilling etc. ( External work).

28 mm dia

35 mm dia

42 mm dia

54 mm dia

76 mm dia

89 mm dia

108 mm dia

Providing, laying, Jointing, Testing and commissioning of UPVC pressure pipes of 10Kg/Sqcm pressure rating class 5 (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation Including laying cement concrete 1:2:4 alround UPVC pipe including bed concrete and thrust blocks at bends as per standard design (For garden hydrants).

Providing and fixing of cast iron wafer type butterfly valves (PN 10) complete with 2 nos. matching flanges ( table-E) , bolts, nuts, washers 3 mm thick insertion neoprene gasket conforming to IS 13095.

100 mm dia

Providing and fixing motorised butterfly valve, IP- 67, with float type sensors suitable for 240 volts with working pressure rating of not less than 5kg/cm2, torque of motor should be capable to open and close valve at 5 kg/sq.cm pressure, with control panel and sensors to open valve when water level is low in tanks and to close when water level is high in water tanks including 03 Nos butterfly valves along with byepass piping, necessary cables, conduits, upto junction box ( upto 6 mt qty approx) etc. complete.

50 mm dia

SEWAGE TREATMENT PLANT

Design, supplying, installing, testing & commissioning of Combine Sewage and Effluent Treatment Plant for 540 KLD (500 KLD STP + 40 KLD ETP) capacity, electro mechanical system based on SBR technology. & (150 KLD STP+ 20 KLD ETP)lectro mechanical system based on Advanced MBBR technology. (excluding all Civil & construction work)

Anticipated effluent parameters before treatment:

BOD 250-400 mg/lt

COD 600-800 mg/lt.

SS 200-450 mg/lt.

Oil & Grease upto 20-30 mg/lt

Desired discharge standard after UF are as below:

BOD Less than 5 Mg/L

S. Solids Less than 5 Mg/L

COD Less than 40 Mg/L

Oil & Grease Less than 1 Mg / L

Combined Sewage treatment and Effluent treatment plant shall include the following Civil Units : (Civil Scope)

Bar Screen cum Oil & Grease Chamber

Sewage equalization tank/sump

Reaction and Settling tank for ETP

SBR Tank

Chlorine Contact Tank

Sludge Holding Tank

UF Feed Tank

UF Permeate Tank

Soft Water Tank

Supply, installation, testing & commissioning of 2 Nos Stainless Steel Perforated, Corse Type Bar Screen Size 500mm x 750 mm with suitable garbage lifting arrangement. Make: Jash/Huber/Wastech/ Johnson/BS enviro

Supply, installation, testing & commissioning of level indicators and controllers for automatic operation of the complete system with high/low level alarm complete with auxillary NO/NC contacts. (Required in equalization tank, chlorine contact tank, sludge holding tank ).

Supply, installation, testing & commissioning of Submersible, non clogging type pumps capable of handling solids upto 20mm having CI casing & CI impeller complete with mechanical seal & all accessories, motor of required capacity. Delivery header with isolation valve, pressure gauge on delivery line with isolation cock. Pumps shall have following duty Make-Wilo/Grundfos/KSB/KBL.(1 Set=1Working+1Standby).

Submersible Sewage Transfer Pumps

Flow Rate (each) = 35 m3 / hr

Head = 8-10 Mtr

Submersible Sewage Transfer Pumps

No. of pumps 2 (1 Working + 1 Standby): 1 set

Flow Rate (each) = 7.5 m3 / hr

Head = 8-10 Mtr

Plant room sump pump (For ETP)

Flow rate = 20 m3/hr

Head = 15 Mts

Cost shall be inclusive of rigid (MS C Class) /PVC Flexible Pipe 100 mm dia , rope for lifting pump from sump to outside.

Providing and fixing horizonal,centrifugal sludge transfer pump . The pumps shall have CI casing, CI Impeller with mechanical rotary shaft seal. Motor to be suitable for including all necessary piping valves and other accessories complete as required. Solid Handling capacity 7-8 mm. (1 Set=1Working+1Standby).

Sludge Recirculation Pump

Capacity : 8 Cum/hr.

Head : 8-10 mtrs.

Air diffusion system shall include the following:

Supply, installation, testing & commissioning of twin lobe, rotary Air blower capable of delivering 600 cum/hr @ 5000mmwg of free air at required pressure driven through “V” belt or directly coupled through flexible coupling to a TEFCmotor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. Make- Everest/ Usha/Beta (1 Set=1Working+1Standby).

Air Blowers

Flow Rate (each) = 600 m3 / hr @5000mmwg

Supply, installation, testing & commissioning of twin lobe, rotary Air blower capable of delivering 150 cum/hr of free air at required pressure driven through “V” belt or directly coupled through flexible coupling to a TEFCmotor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply. Make- Everest/ Usha/Airvac

Air Blowers

No. of blower 2 (1 Working + 1 Standby): 1 set

Flow Rate (each) = 150 m3 / hr

Air piping shall comprise of MS C Class for NOn submerged and SS 304 for all submerged air lines & Plant room complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, paint,supports & clamps, making good the wall wherever required. Contactor to submit detailed P & I indicating their proposal.

Providing and fixing all interconnecting piping (as described below) and isolation control valves for making the system complete. The piping material shall be MS 'C' class.

SS 304 : Submerged air piping .

MS Epoxy : Air piping & pumped effluent riser ( non-submerged)

MS C Class piping : Pumped effluent & tank

PVC Piping : All overflow from the tanks

Supply, installation, testing & commissioning of SBR Package with 2 tank system, Fully automatic system with Diffused aeration system comprises of , EPDM air diffusers and air grid in uPVC. Moving decanter with thickness more than 3mm shall be installed in reactor tank for decanted water extraction, MOC of decanter shall be SS-304 (Make - TATA / Jindal) driven by Geared motor of suitable Power. Inlet of sewage water decantation and aeration shall be automatic and PLC controlled with the help of automatic valves or by equipment arrangement. SBR cycle shall be auto controlled and continous feedback level transmitter (Ultrasonic or Hydrostatic) shall be installed in each reactor tank (1 no DO sensor, 1 no level transmitter and 1 no PH transmitter). Plant shall give the water quality as above & as per Specification. Decanter Make: C-TECH/PRIMER TECH//BS ENVIRO

Supply, installation, testing and commissioning of MBBR media having porous structure with very high syrface area of 2500 m2/m3. The MBR media shall have very high organic loading rate and ability to retain microorganism inside the structure also.

Make: Kurary -Japan/Anox Kaldness-USA/Headworks-USA

Supply, installation, testing and commissioning of PVC tube deck settling media to be installed in Tube Settler Tank alongwith retainer plates and suitable sludge removal arrangement either by pumps or any other suitable arrangement. Capacities, length, width,depth, of the media shall be enough for proper functioning of STP. Make-PP Aqua MM Aqua

Supplying, installing, testing & commissioning of centrifugal\ feed pumps, CI body, CI impeller. motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer at suction. The pump shall be suitable for 415±10% volts 3 phase AC supply Make-Kirloskar/M&P/Johnson) (1 Set=1Working+1Standby).

Filter feed pumps:

Capacity : 30 Cum/hr.

Head : 25-30 Mtrs

Filter feed pumps:

Capacity : 15 Cum/hr.

Head : 25-30 Mtrs

Softner feed pumps:

Capacity : 10 Cum/hr.

Head : 20-25 Mtrs

Supplying, installing, testing and commissioning of MSEP vessel filter with all necessary accessories. Filter shall be suitable for minimum working pressure of 5 kg / cm2 and shall include media, standard fittings like pressure gauges, sampling cock, rinse drain, vacuum breaker etc. The MS sheet thickness for tank shall be min. 6mm and for dishess shall 8mm. The internal surfaces of tank shall be treated with epoxy coaing and external surface with primer and anticorrosive enamel paint (Min. 2 coats). Make: Thermax/Ion Exchange/Hydrocon/BS enviro.

Multigrade pressure sand filter

Flow rate : 30 Cum/hr

Filteration velocity : 15 cum/hr/sqm

Filter Diameter : 1600 MM

Shell Thickness: 8 mm

Disch Thickness: 10 mm

Corrosion allownace: min 2 mm

Multigrade pressure sand filter

Flow rate : 15 Cum/hr

Filteration velocity : 15 cum/hr/sqm

Filter Diameter : 1500 MM

Shell Thickness: 6 mm

Disch Thickness: 8 mm

Corrosion allownace: min 2 mm

Activated Carbon Filter

Flow Rate : 30 Cum/hr

Filteration velocity : 15 cum/hr/sqm

Filter Diameter : 1600 mm

Shell Thickness: 8 mm

Disch Thickness: 10 mm

Corrosion allownace: min 2 mm

Activated Carbon Filter

Flow Rate : 15 Cum/hr

Filteration velocity : 15 cum/hr/sqm

Filter Diameter : 1500 mm

Shell Thickness: 6 mm

Disch Thickness: 8 mm

Corrosion allownace: min 2 mm

Providing, fixing, testing & commissioning of MSRL water softening plant (suitable for 3 Kg/Sqcm working pressure) complete with initial charge with T-40 NA Resin, Butterfly valve with built in ejector for controlling all operations), regeneration system and HDPE Brine tank with SS Agitator, pressure gauge at inlet, outlet and back wash (each with isolation cock), valves, fittings and water hardness testing kit & associated works. Softener shall be suitable for the following duty: Make: Thermax/Ion Exchange/Hydrocon/BS enviro.

Raw water hardness 500 Mg/L

Treated water hardness 100 Mg/L

Regeneration Period 10 Hrs.

Capacity : 10000 LPH, OBR: 100

Supply, installation, testing & commissioning of UV system for purification of recycled water from STP. With all accessories complete in all respect Make-Alfa/Sukruit

Cap: 30 m3/h with all part in SS 316. The UV should have min inetnsity of <60000 microseimens/cm2

Supply, installation, testing & commissioning of UV system for purification of recycled water from STP. With all accessories complete in all respect Make-Alfa/Wastech/Hydrocon).Cap: 15 m3/h with all part in SS 316. The UV should have min inetnsity of <60000 microseimens/cm2

Supply, installation, testing and commissioning of filter press of Suitable Capacity 16"x 16"x 18 Plates with CI frame, PP plates with filter cloth interconnecting piping and poly dosing system complete. (Make- Auro/NM Patel/ Pharmatech)

Supply, installation, testing and commissioning of Basket type Centrifuge of Suitable dia 900 mm with interconnecting piping and poly dosing system complete. Make: Humboldt Wedag/Hiller/Alfa Laval

Supply, installation, testing & commissioning of positive displacement type screw slurry pump with MS casing, SS-strator with internal rubber lining, gland packing seal, solid handling capacity upto 7 to 10% of the effective percentage of sludge and direct drive with motor.Make-UT/Roto/Technoflow.(1 Set=1Working+1Standby)

Sludeg Feed Pump

Capacity : 2 m3/hr

Head : 40 mtrs. (1W+ 1S)

Supplying, installing, testing & commissioning of Submersible Mixer 1.5 HP for Anoxic Tank. Make: Aqua Italy/ABS

Electrical Panel- Motor Control Centre

Motor Control Centre

Incoming

600 amps TPN MCCB with the following accessories:

c) Phase indicating lamps shall be protected by 2 amp SP MCB 3 sets.

Bus Bar

400 amp TPN (15 KA) copper bus bar with heat shrinkable insulation sleeves.

Outgoing

b) Spare MCB's of following capacities

I. 32 amps TPN MCB's 3 Nos.

a) All MCCB's / MCB's shall be of 15 KA breaking capacity and suitable for motor duty application.

b) All motor starters shall be provided with Auotmatic level controller.

c) DOL starters shall be used for moters below 10 HP and Star-Delta Starters for other motors.

d) Provision shall be made for providing potential free contacts to all pumps starters

MCC for all STP equipments/ pumps as described in sub head-A with provision for all future pump air blower etc. Make: Brisanzia

MCC for all STP equipments/ pumps as described in sub head-A with provision for all future pump air blower etc. Make: Brisanzia

Make: Vendor Specific with CPRI Approval

Supplying, installing, testing & commissioning of Cables , Conector, Cable Trays, to make Electrical Installation Complete.

Supplying, installing, testing & commissioning of Cables , Conector, Cable Trays, to make Electrical Installation Complete.

Supplying, installing, testing & commissioning of Electromegnatic Flowmeter of min 3 inch dia at Inlet and Outlet of system. Make: FORBES MARSHALL /SIEMENS /HACH

Supplying, installing, testing & commissioning of Electromegnatic Flowmeter of min 3 inch dia. Make: Krohne Marshall/Nivo/Manas

Supply, Fabrication, installation, testing and commisioning of phyisco chemical treatment based effluent treatment plant with effluent handling capacity 40 m3 per day. The ETP shall be designed as water retaining structures, with necessary chemical dosing as required by the manufacturer's design. All the equipment, piping, and pumps to be housed in the ETP , inlet, outlet, overflow, vent, etc. The Plant shall be complete with a central Electrical Power and Control panel fully pre/site wired and with all power and control cables to all pumps and equipment including all instrumentation, level and other controls. Note: Treated effluent will be mixed in Filter Feed Tank/CCT of STP.

Effluent from labs etc. Some solvent/ chemical waste originating typically from College complex shall also be discharged into the ETP. Design to take consideration of same.

Daily average flow : 5 Cum/hr

BOD : 250 - 600 mg/l

S. Solids : 400 - 650 Mg/l

COD : 600 - 1200 mg/l

Oil & Grease : 50-140 mg/L

Effluent discharge standard after chemical treatment before mixing to CCT :-

S. Solids : Less than 100 mg/l

COD : Less than 100 mg/l

Oil & Grease : Less than 5 mg/l

BOD : Less than 30 Mg/L

The ETP shall consist of following units but not limited to these unit as may be required by the manufacturer's design. MS PVC coated rungs in all tanks & Platform for maintenance etc. complete as required.

SS Perforated screen having provision for chain lifting arrangement etc. complete as required ( 1 SET)

Collection cum Equalization tank including provision for aeration will be kept to avoid any smell problems in RCC Construction (Civil contractor Scope)-10 Cum ( 1 SET)

Reaction tank with air diffuser and piping complete of adequate capacity. Fine air bubble jet diffuser with EPDM seat minimum number of diffusers to be provided as per manufacturer's recommendations in RCC Construction.

Secondary clarifier tank, Tube Deck Media, hopper bottom type with arrangement of deep well, baffle wall, scum removal arrangement, outlet launders with arrangement of lifting sludge from the bottom etc. complete as required in RCC Construction.(1 SET)

Providing and fixing all piping (as described below) and isolation control valves, non return valves etc. for making the system complete.

PVC piping (10kg/sqcm) - For all submerged waste water piping.

MS (C Class) - For all exposed air piping and flexible stainless steel pipe for submerged air piping.

GI (C class) for all other water piping. ( 1 LOT)

Providing and fixing all instrumentation eg. Pressure guages, level controllers, sensors, rotametres for air, water etc. for making the system complete (1 LOT)

EQUALIZED WASTE WATER TRANSFER PUMPS :

Providing, installation, testing & commissioning of Horizontal / Submersible centrifugal pumps solid handling (min. 20 mm) pumps. The pumps shall be made of CI casing, bronze Impellar, CS shaft & sleeve, Mechanical Seal are connected to a TEFC induction motor mounted on a common channel base frame with coupling guard, 150 mm dia pressure gauge with GM isolation cock, suitable vibration eliminator pads of approved design. Motor to be suitable for 400/440 V, 3 Phase, 50 cycles AC power supply, including all necessary piping, valves and other accessories and concrete foundation complete as required.

Capacity : 5.0 M3/hr @ Discharge Head 12 M head (1 Working + 1 Standby) (1 SET)

Mono block centrifugal Sludge Transfer Pumps (2 Nos. - One working & one standby ( 1 SET)

(Solid handling cap. 6 mm)

Flow rate (each) = 1 m3 / hr

Head = 8-10 Mtr

Providing and fixing lime/alum/polyelectrolyte dosing system consisting of ABS lime dosing pump (0-6 lph) with 100 l HDPE tanks including all piping from the dozer to the reaction tank etc. complete in

Contractor shall include all electrical and mechanical items as required to operate the system automatically and also include in his rates any other components/tanks/ equipment/ etc. required to complete the job as required. Only main power supply with the earthing to be (ETP+STP) main control panel shall be provided by the owner through other agencies. The electrical panle will also include all the required NO/NC contacts, contactors etc. required to provide BMS connectivity.

Bypass arrangement shall be provided such that equalization tank pump can be used to pump out sewage to external manhole incase of maintenance of ETP.

All ETP system complete in all respect exclude all Civil & construction works.

Design, supplying, installing, testing & commissioning of EFFLUENT Treatment Plant

Nature of Waste - Hospital waste

Daily average flow - 20 cum/day

Anticipated effluent parameters before treatment:

BOD5 - 300 mg/lt

COD - 800 mg/lt.

Oil & Grease - 7 mg/lt.

Ecoli - >106 MPN

Sulphate - 29

Desired EFFLUENT discharge standard as well as meeting norms for Gardening and washing set makeup etc after treatment are as below:

BOD5 - Less than 30 Mg/L

COD - Less than 250 Mg/L

Oil & Grease - Less than 5 Mg / L

Ecoli - < 103 MPN

Sulphate - Less than 10 Mg/L

Effluent treatment plant shall include the following items:

Inlet Sump

Bar Screen Chamber

Effluent equalization tank

Oil & Grease chamber (Oil Skimmer)

FAB Tanks

Tube Settler

Clear water Tank

Sludge Holding Tank

Filtration through DMF & ACF

Air Blowers, Pumps & equipment

Piping, valves etc

Electrical Panel & Cabling

Filter press along with screw pump

Instrumentation like Metering devices, Sensors etc

Chlorination

Supply, installation, testing & commissioning of 2 Nos. Stainless Steel Corrugated Perforated Bar Screen havin size 500x800x5mm thickness with minimum 10 mm mesh size

Supply, installation, testing & commissioning of level indicators and controllers for automatic operation of the complete system with high/low level alarm complete with auxillary NO/NC contacts. (Required in equalization tank, chlorine contact tank, sludge holding tank).

Supply, installation, testing & commissioning of non clogging type centrifugal type pumps capable of solids handling upto 8 mm having CI casing & CI impeller complete with mechanical seal & all accessories, motor of required capacity. Delivery header with isolation valve, Pumps shall have following duty.

Equalization Transfer Pumps

ONE set - (1 Working + 1 Standby)

Flow rate (each) = 2 m3/hr

Head = 10.00 Mtr

Motor HP = As per manufacturer recommendation

Make-Kirloskar/CRI/KSB

Supply, installation, testing & commissioning of non clogging type Sludge transfer pumps CI material complete with mechanical seal & all accessories, motor of required capacity.Suction header with Isolation Butterly valves, Delivery header with isolation Butterly valve,NRV's. Pumps shall have following duty.

Sludge Transfer pumps

ONE set - (1 Working + 1 Standby)

Flow Rate (each) = 2.0 m3 / hr

Head = 8-10 Mtr

Motor HP = As per manufacturer recommendation

Make-Kirloskar/CRI

AIR DIFFUSION SYSTEM

Air diffusion system shall include the following:

Capable of delivering 20.0 cum/hr of free air at 0.55 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFCmotor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles A/C supply.

Twin type rotary air blowers.

ONE sets - ( 1 Working + 1 Standby)

Make-Beta/Airvac/SMW/Akash

Capacity- 25 m3/hr

Air piping shall comprise of pipes droppers / laterals with UPVC/MS Class (epoxy coated) Header complete with all fitting such as tees, crosses, plugs, sockets, Elbows, reducer,supporters & clamps, Puddle flange etc cutting chases and making good.

Non-clog type air dispersion system in the form of Air grid , Bottom faced holes at designed angles for FAB reactors / retreviable type diffusers & Top face for Equilisation Tank,Flocculation chamber,Sludge Holdng Tank,

Providing and fixing all interconnecting piping with all required isolation control valves for making the system complete functional as per site.

Supply, installation, testing and commissioning of MBBR media to be installed in FAB Tank

Supply, installation, testing and commissioning of suitable PVC tube deck settling media to be installed in Tube Setller tank alongwith suitable sludge removal arrangement either by pumps or air lifting pumps .

Dosing Systems

Supply, installation, testing & commissioning of Polyelectrolyte dosing system comprising of 100 ltrs HDPE tank with 0- lph electronic metering type pump in flocculation chamber

Supply, installation, testing & commissioning of Alum dosing system comprising of 100 ltrs HDPE tank with 0-6 lph electronic metering type pump in flocculation chamber

Supply, installation, testing & commissioning of Lime dosing system comprising of 100 ltrs HDPE tank with 0-12 lph electronic metering type pump in flocculation chamber.

Supply, installation, testing & commissioning of Chlorine dosing system comprising of 100 ltrs HDPE tank with 0-12 lph electronic metering type pump in flocculation chamber.

Supply, installation, testing & commissioning factory assembled and tested vertical pumpset with CI body and CI impeller, shaft of CI,CI suction and discharge and C.I. Base & head, mechanical seal, connected to a TEFC induction motor suitable for 400/440 volts, 3 phase 50 cycles A.C. supply with,isolation valve, non return valve of required sizes at discharge and suction of each pump, vibration eliminating pads as required, M.S channel fabricated common base plate bolted to cement concrete foundations complete.

Filter feed pumps:

Capacity : 2.0 Cum/hr.

Head : 30-35 Mtr

ONE set – ( 1 W + 1 S)

Motor HP = As per manufacturer recommendation

Make-Kirloskar/CRI

Treated Water Transfer pumps.

Capacity : 3.0 m3/hr

Head : 30-35 mtrs.

ONE set - ( 1 Working + 1 Standby)

Motor HP = As per manufacturer recommendation

Make-Kirloskar/CRI

Supply, installtiong, testing and commissioning of FRP vessel filter with frontal piping and associated valves and accessories. Filter shall be suitable for minimum working pressure of 3.5 kg / cm2 and shall include media, standard fittings like pressure gauges, sampling cock, rinse drain, vacuum breaker etc

Dual Media filter- Media Anthracite + Sand+ supporting media.

Flow rate : 2.5 Cum/hr

Filter Diameter : 600mm x 1800 mm HOS

Make-Oxybee solution/klenge system/Kunal enter prises

Activated Carbon Filter- Iodine value Graded Activated Carbon.

Flow Rate :2.5 Cum/hr

Filter Diameter : 600mm x 1800 mm HOS

Make-Oxybee/klengen

Supply, installation, testing and commissioning sludge handling system capable for 20 KLD STP, including filter press of Suitable Capacity with CI frame, PP plates complete with filter cloth complete with Filter press feed pump (Screw Type-1W+1S) – with interconnecting piping .

Make-Oxybee solution/klenge system/Kunal enter prises

Supply , Installation, Testing & Commissioning of Following metering devices:-

Outlet Treated water effluent Digital Flow meter

ELECTRICAL INSTALLATION FOR 20 KLD ETP

Constructing the following tanks & chambers in 4mm thick MS construction including the top cover as per as the approved calculation including 1mm FRP lining inside the tank and epoxy painting on out side of the approved colors and shades of emanel paint over a coat of primer .the plant should be of compact nature mounted on a common platform.The above cost shall include the cost of all required MS structure for skid plat form ,walking platform,hand rail ,staircase ,puddle flanges,foot rest,manhole cover etc with painting of desired shadeof enamel paint over a coat of primer.

Equalisation tank :- 8000 lit Civil (Client Scope )

Chemical reaction tank

Oxyprocessor tank ( Make -Oxybee solution /klengen system/Kunal enterprises)

Secondary settling tank ( Make -Oxybee solution /klengen system/Kunal enterprises)

Chlorine contact tank

Sludge holding tank (Syntex) ( Make -Oxybee solution /klengen system/Kunal enterprises)

All tanks are constructed in MSEP except bar screen,equalization tank and treated water tank

ULTRA FILTRATION PLANT

Providing, installation, testing & commissioning of fully automatic Ultra Filtration System (UF) of capacity 30 m3/hr. The system should be complete with Feed Pump (1W+1SB), Back Wash Pump (1W+1SB), Cartidge Filter, UF Membrane with Housing, Flushing/Cleaning System, complete instrumentation for automation and monitoring Rotameter, pressure guage, interconnecting pipe, vales/solenoid valve, PLC base electrical panel with cabling all complete with all accessories. UF Membraine: GE/DOW

RO SYSTEM

Supplying, lifting at the terrace, assembly, erection, testing and commissioning of RO Water treatment system including centalised water cooler for cold water proand all its components of required size as per water test analysis to make the water suitable for drinking, complete including the following as mentioned below. The cost will include testing of permeate water sample from a CPCB approved test laboratory, generating and providing membrane analysis data form the licensed manufacturer's software etc.

Permeate water quantity = 1000 lit/hr. and Permeate water quantity = 500 lit/hr.

Minimum Recovery = 70%-75%

Raw Water Characteristics - As per Water Test Analysis Report of Shriram Test Laboratory to be got done by the supplier

Raw water Quality

Turbidity : <1NTU

Chlorides : 205 ppm

Sulphates : 105 ppm

Treated Water Quality

Turbidity : <1NTU

Chlorides : < 10 ppm

Sulphates : < 5 ppm

TDS : < 50 ppm

SS Vertical centrifugal Raw Water Pump (1 Working + 1 Stand-by)

FRP Dual Media Filter

Activated Carbon Filter

Antiscalant Dosing System including pump chemical dosing pump, tanks etc.

Polypropylene Micron/cartridge Filter and SS housing

Stainless steel vertical multistage inline high pressure pump (1 Working) including dry running protection

Spirally wounded 6 nos. of RO Membranes

Composite FRP RO pressure tube/vessel

Automatic RO Module Cleaning System including chemical pump, cartridge filter, tanks etc.

pH correction system incl. chemical dosing pump, tanks etc.

Instrumentation including flow meters, digital TDS meter, digital pH meter, pressure gauges, low pressure switch, high pressure switch etc. complete.

SS-316L (8 kg/cm2) piping and ABS valves for low pressure and SS-316, schedule 10 piping and SS-316 L valves for high pressure piping in the plant.

Electrical panel including all starters, overload relays, single phase preventers, voltmeters, ammeters, MCB's, indicating lights, push buttons, rocker switches, incomers, auto-manual switches etc. complete.

All cabling , connections, terminations etc. required for the job.

Permeate water quantity =500 lit/hr. described above (a) to (m).

Supply Installation, Testing & Commissioning of water cooler having nominal cooling capacity of 150 liters per hours, with 150 litres storage tank with 3 nos. of faucets, one no goose neck type( for glass filling ) and other one fountain type (for drinking) both with separate mecahnical lever control with 4.5 HP electric motor for compressor to work on one phase 230 volts 50 Hz AC power supply with complete assessories including cutting and making wall as required.

Supply Installation, Testing & Commissioning of below counter installation type Drinking Water R.O. unit with micron filtration pre-treatment unit, skid mounted R.O. module with pressure pump and pressure tank, 6 m long food grade PP permeate line including connection to drinking water cooler, Coffee machine, complete in all respects.

Permeate 150 ltr/hr, Make Pentair/Fontus/Kent R.O.

ELECTRICAL WORKS

DISTRIBUTION CABLES & CABLE TRAY

Supply of following sizes of 1.1KV grade multicore Copper / aluminium conductor XLPE insulated and PVC sheathed armoured cable conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule by architect / consultant).

2 core, 6 sq.mm copper armoured cable

2 core, 10 sq.mm copper armoured cable

4 core, 6 sq.mm copper armoured cable

4 core, 10 sq.mm copper armoured cable

4 core, 16 sq.mm copper armoured cable

4 core 25 sq. mm

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required.

2 X 6 sq. mm (19mm) For copper armoured cable

4 X 6 sq. mm (25mm) For copper armoured cable

4 X 10 sq. mm (25mm) For copper armoured cable

4 X 16 sq. mm (28mm) For copper armoured cable

2 X 10 sq. mm (19mm) For copper armoured cable

Rubber mat 1000 mm. Wide to withstand 1.1 KV dielectric strength as per latest IS 15652-2006.

Supply, erection, testing and commissioning of following sizes of splitter of aluminium die cast body in suitable size of G.I. Box.

Supply, Installation, Testing & Commissioning of Earthing Junction Box size - 400mm x 300mm x 80mm made out of 16 SWG CRCA sheet with seven tank process & powder coating, earthing link (32mm x 6mm copper strip) front door with glass as complete as required.

Supply & installation of 32 Amp 3 phase, 415 volt, 50 Hz water tight (IP-55) socket outlet with interlocking switch complete with all fixing accessories.

Supply & installation of 32 Amp single phase 240 Volt, 50 Hz, water tight (IP-55) socket outlet with interlocking switch complete with all the fixing accessories as below.

Movement detectors (Infrared Type) Inbuilt ambient light sensor with adjustable lux level 5 to 600 lux, adjustable time delay from 1 minute to 15 minute, adjustable detection range 0 to 12 meter. The movement detector shall have lens, 360 deg and coverage area shall not be less than 48 sq. meter if height is 2.7 meter. The contact rating shall be suitable for 2000 watt light load.

Supply, Installation, Testing & Commissioning of 1P, 2 module surge protection device complete as required.

Supply & fixing of following size (GP RACEWAY- Fabricated from GP Sheet) race ways for electrical & LV wiring including neoprene gasket in joints, cutting the floor & jaming the race way / hanging in ceiling, supporting arrangement as approved by consultant / architect with all necssary hard ware (including civil work) as per site requirement. The thickness of raceway & cover shall be as per technical specification.

100 mm wide x 40 mm deep.

150 mm wide x 40 mm deep.

200 mm wide x 40 mm deep.

250 mm wide x 40 mm deep.

300 mm wide x 40 mm deep.

Supply & fixing of following size of Raceway Junction Box made out of GP Sheet for electrical & LV wiring including, cutting the floor & jaming the junction box / hanging in ceiling, supporting arrangement as approved by consultant / architect with all necssary hard ware (including civil work).(Junction box to be provided as per drawing/ as per site requirement & as per specification). The thickness of junction box shall be a as per thechnical specification.

150 mm wide x 50 mm deep.

200 mm wide x 50 mm deep.

250 mm wide x 50 mm deep.

300 mm wide x 50 mm deep.

350 mm wide x 50 mm deep.

Supply & Laying of following sizes of 1.1KV grade multistranded copper conductor PVC insulated cable including termination complete as required in existing cable tray / existing conduit.

1C x 6 sq.mm PVC Insulated cu wire including termination etc.

1C x 10 sq.mm PVC Insulated cu wire including termination etc.

1C x 16 sq.mm PVC Insulated cu wire including termination etc.

1C x 25 sq.mm PVC Insulated cu wire including termination etc.

1C x 35 sq.mm PVC Insulated cu wire including termination etc.

1C x 50 sq.mm PVC Insulated cu wire including termination etc.

1C x 150 sq.mm PVC Insulated cu wire including termination etc.

Providing & painting of following Fire retardant paint 2 hour rating on XLPE insulated copper/ aluminium cable as per specifications.

DISTRIBUTION PANEL

RISING MAIN, TAPP OF BOXES AND END FEED UNIT-

END FEED UNIT-

Design, Manufacturing, Supply, Receiving, Unloading, Shifting, Installation, Testing & Commissioning of following End Feed Unit housing fabricated out of 14G CRCA powder coated (as approved) sheet steel for the Rising Mains fitted with following MCCB. The End Feed Unit should complete with solid aluminium links of rated capacity of MCCB to Rising Mains. The End Feed Unit should be complete with suitable size of glands plate for incoming cables. All MCCB shall have Ics value of 50 KA. Each end feed unit shall have a set of 3 nos. phase LED Type indicating lights with control fuses.

315 Amp, FP MCCB

400 Amp, FP MCCB

TAP OFF UNIT

Design, Manufacturing, Supply, Receiving, Unloading, Shifting, Installation, Testing & Commissioning of cubical type tap off unit box fabricated out of 1.6 mm thick CRCA sheet, dust and vermin proof, with hinged detachable doors and painted front, comprising LED type indication lamps with toggle switches and 4 pole MCCB terminated directly with tap off box with Bus Bar links on the incoming side and suitable for cable connection on the outgoing side including making connections, interconnections, earthing complete as required. All MCCB shall have Ics value of 36 KA and Thermal Magnetc release for over current & short circuit.

Tap Off Box with 63 Amp TP+N MCCB.

Tap Off Box with 100 Amp TP+N MCCB.

Tap Off Box with 125 Amp TP+N MCCB.

Tap Off Box with 160 Amp TP+N MCCB.

DISTRIBUTION PANEL

MAIN DG BACKUP PANEL (MEDICAL COLLEGE)

INCOMING

2 No. 1000 Amp FP Moulded Case Circuit Breaker

2 No. Digital Multi Function Meter with CT's.

2 Set of phase indicating lamps with Single Pole MCB.

2 Set of ON / OFF indicating lamps with Single Pole MCB.

1 Set of Mechanical interlocking between incommer & bus coupler.

BUS COUPLER

1 No. 1000 Amp FP Moulded Case Circuit Breaker

BUS BAR

1250 Amp TPN aluminium bus bar.

OUTGOING

01 No. 800 Amp FP Moulded Case Circuit Breaker

02 No. 500 Amp FP Moulded Case Circuit Breaker

06 No.160 Amp FP Moulded Case Circuit Breaker

11 No.100 Amp FP Moulded Case Circuit Breaker & & 8 No. KWH meter.

1 Lot of control / power wiring.

Panel described as above

MEDICAL EQUIPMENT PANEL-1 (MEDICAL COLLEGE)

INCOMING

01 No. 800 Amp FP Moulded Case Circuit Breaker

01 No. Digital Multi Function Meter with CT's.

01 Set of phase indicating lamps with Single Pole MCB.

01 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

1000 Amp TPN aluminium bus bar.

OUTGOING

04 No. 250 Amp FP Moulded Case Circuit Breaker

02 No. 160 Amp FP Moulded Case Circuit Breaker

08 No.100 Amp FP Moulded Case Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

MEDICAL EQUIPMENT PANEL-2 (MEDICAL COLLEGE)

INCOMING

01 No. 500 Amp FP Moulded Case Circuit Breaker

01 No. Digital Multi Function Meter with CT's.

01 Set of phase indicating lamps with Single Pole MCB.

01 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

630 Amp TPN aluminium bus bar.

OUTGOING

02 No. 160 Amp FP Moulded Case Circuit Breaker

07 No. 100 Amp FP Moulded Case Circuit Breaker

08 No.100 Amp FP Moulded Case Circuit Breaker

12 No.63 Amp FP Moulded Case Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

LIGHT PANEL-1,2,3 &4 (MEDICAL COLLEGE)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

300 Amp TPN aluminium bus bar.

OUTGOING

08 Nos 25 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

POWER PANEL-1 (DG SUPPLY) (MEDICAL COLLEGE)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

05 Nos40 Amp DP Miniature Circuit Breaker

06 Nos 25 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

POWER PANEL-2 (DG SUPPLY) (MEDICAL COLLEGE)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

07 Nos40 Amp DP Miniature Circuit Breaker

04 Nos 25 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

AHU PANEL-1 (DG SUPPLY) (MEDICAL COLLEGE)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

04 Nos 25 Amp TPN Miniature Circuit Breaker

05 Nos 40 Amp TPN Miniature Circuit Breaker

02 Nos 63 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

AHU PANEL-2 (DG SUPPLY) (MEDICAL COLLEGE)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

03 Nos 25 Amp TPN Miniature Circuit Breaker

06 Nos 40 Amp TPN Miniature Circuit Breaker

03 Nos 25 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

MAIN PANEL-2 (NORMAL SUPPLY) (MEDICAL COLLEGE)

INCOMING

1 No 400 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

500 Amp TPN aluminium bus bar.

OUTGOING

03 No250 Amp FP Moulded Case Circuit Breaker

01 No 200 Amp FP Moulded Case Circuit Breaker

03No 160 Amp FP Moulded Case Circuit Breaker

01 No 100 Amp FP Moulded Case Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

POWER PANEL-1 (NORMAL SUPPLY) (MEDICAL COLLEGE)

INCOMING

1 No 160 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

200 Amp TPN aluminium bus bar.

OUTGOING

08 Nos 63 Amp TPN Miniature Circuit Breaker

03Nos 25 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

POWER PANEL-2 (NORMAL SUPPLY) (MEDICAL COLLEGE)

INCOMING

1 No 160 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

200 Amp TPN aluminium bus bar.

OUTGOING

11 Nos 63 Amp TPN Miniature Circuit Breaker

04 Nos 25 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

POWER PANEL-3 & 4 (NORMAL SUPPLY) (MEDICAL COLLEGE)

INCOMING

1 No 250 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

300 Amp TPN aluminium bus bar.

OUTGOING

16 Nos 63 Amp TPN Miniature Circuit Breaker

03 Nos 25 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

POWER PANEL-5 (NORMAL SUPPLY) (MEDICAL COLLEGE)

INCOMING

1 No 200 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

250 Amp TPN aluminium bus bar.

OUTGOING

15 Nos 63 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

POWER PANEL-6 (NORMAL SUPPLY) (MEDICAL COLLEGE)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

7 Nos 63 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

UPS OUTGOING PANEL- (3 x60 KVA) (MEDICAL COLLEGE)

INCOMING

03 No. 160 Amp FP Moulded Case Circuit Breaker

03 Set of phase indicating lamps with Single Pole MCB.

03 Set of ON / OFF indicating lamps with Single Pole MCB.

03 No. Digital Multi Function Meter with CT's.

BUS BAR

400 Amp FP Copper bus bar.

OUTGOING

02 Nos 160 Amp FP Moulded Case Circuit Breaker

01 Nos 100 Amp FP Moulded Case Circuit Breaker

02 Nos 63 Amp FP Moulded Case Circuit Breaker

02 No. 25 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

UPS PANEL-1 (MEDICAL COLLEGE)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium busbar.

OUTGOING

06 No. 25 Amp TPN Miniature Circuit Breaker

02 No. 40 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

UPS PANEL-2 (MEDICAL COLLEGE)

INCOMING

1 No 160 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

200 Amp TPN aluminium busbar.

OUTGOING

10 No. 25 Amp TPN Miniature Circuit Breaker

04 No. 40 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

EM. PANEL-1 (MEDICAL COLLEGE)

INCOMING

1 No 63 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

100 Amp TPN aluminium busbar.

OUTGOING

08 No. 25 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

EM. PANEL-2 (MEDICAL COLLEGE)

INCOMING

1 No 63 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

100 Amp TPN aluminium busbar.

OUTGOING

14 No. 25 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

LIFT PANEL-1&2 - TERRECE FLOOR (MEDICAL COLLEGE)

INCOMING

1 No 63 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

03 Nos 63A FP RCBO.

05 Nos 40A TPN Miniature Circuit Breaker.

02 Nos 40A DP Miniature Circuit Breaker.

1 Lot of control / power wiring.

Panel described as above

KITCHEN (MEDICAL COLLEGE)

INCOMING

1 No 160 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

200 Amp TPN aluminium busbar.

OUTGOING

02 No 63 Amp FP Moulded Case Circuit Breaker

04 No. 63 Amp TPN Miniature Circuit Breaker

04 No. 40 Amp TPN Miniature Circuit Breaker

03 No. 63 Amp DP Miniature Circuit Breaker

02 No. 40 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

ELECTRICAL PANEL-1 (AUDI BLOCK)

INCOMING

1 No 300 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

400 Amp TPN aluminium busbar.

OUTGOING

02 No 125 Amp FP Moulded Case Circuit Breaker

01 No 100 Amp FP Moulded Case Circuit Breaker

03 No 63 Amp FP Moulded Case Circuit Breaker

08 No. 63 Amp TPN Miniature Circuit Breaker

04 No. 25Amp TPN Miniature Circuit Breaker & 3 nos. KWH meter

1 Lot of control / power wiring.

Panel described as above

HVAC PANEL-1 (AUDI BLOCK)

INCOMING

1 No 125 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium busbar.

OUTGOING

07 No. 63 Amp TPN Miniature Circuit Breaker

02 No. 40 Amp TPN Miniature Circuit Breaker

09 No. 25 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

ELECTRICAL PANEL(STUDENT REC.)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

02 Nos 63 Amp TPN Miniature Circuit Breaker

04 Nos 40 Amp TPN Miniature Circuit Breaker

02 Nos 40 Amp DP Miniature Circuit Breaker

01 Nos 25 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

UPS PANEL-1 (AUDI BLOCK)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium busbar.

OUTGOING

1 No 100 Amp FP Moulded Case Circuit Breaker

03 No. 25 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

LIFT DB (AUDI BLOCK)

SCHEDULE ITEM

NON SCHEDULE ITEM

100 Amp TPN aluminium busbar.

OUTGOING

01 No 63 Amp FP RCBO..

01 No. 25 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

MAIN PANEL - 1 (D.G. BACKUP) (BOYS / GIRLS HOSTEL)

INCOMING

1 No. 300 Amp FP Moulded Case Circuit Breaker.

1 No. Digital Multifunction Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

400 Amp TPN aluminium busbar.

OUTGOING

01 Nos 160A FP Moulded Case Circuit Breaker with Digital KWH Meter.

04 Nos 100A FP Moulded Case Circuit Breaker.

10 Nos 25A TPN Miniature Circuit Breaker.

02 Nos 63A DP Miniature Circuit Breaker.

1 Lot of control / power wiring.

Panel described as above

ELECTRICAL PANEL -1 (D.G. BACKUP) (BOYS / GIRLS HOSTEL)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium busbar.

OUTGOING

09 No. 25 Amp TPN Miniature Circuit Breaker

02 No. 63 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

MAIN PANEL - 2 (NORMAL SUPPLY) (BOYS / GIRLS HOSTEL)

INCOMING

1 No 250 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

300 Amp TPN aluminium busbar.

OUTGOING

2 Nos. 160 Amp FP Moulded Case Circuit Breaker

2 Nos. 125 Amp FP Moulded Case Circuit Breaker

5 Nos. 63 Amp TPN Miniature Circuit Breaker

5 Nos. 25 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

ELECTRICAL PANEL -1 (NORMAL SUPPLY) (BOYS / GIRLS HOSTEL)

INCOMING

1 No 160 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

200 Amp TPN aluminium busbar.

OUTGOING

2 Nos. 100 Amp FP Moulded Case Circuit Breaker

4 Nos. 63 Amp TPN Miniature Circuit Breaker

6 Nos. 25 Amp TPN Miniature Circuit Breaker

1 Nos. 63 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

ELECTRICAL PANEL -2 (NORMAL SUPPLY) (BOYS / GIRLS HOSTEL)

INCOMING

1 No 125 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium busbar.

OUTGOING

5 Nos. 63 Amp TPN Miniature Circuit Breaker

5 Nos. 25 Amp TPN Miniature Circuit Breaker

1 Nos. 63 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

ELECTRICAL PANEL -3 (NORMAL SUPPLY) (BOYS / GIRLS HOSTEL)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium busbar.

OUTGOING

5 Nos. 63 Amp TPN Miniature Circuit Breaker

5 Nos. 25 Amp TPN Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

LIFT PANEL-1 (BOYS / GIRLS HOSTEL, TYPE-III, TYPE-IV & TYPE-V))

INCOMING

1 No. 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

03 No. 63 Amp FP RCBO.

01 No. 63 Amp TPN Miniature Circuit Breaker

05 No. 40 Amp TPN Miniature Circuit Breaker

02 No. 40 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

LIFT PANEL-2 (BOYS / GIRLS HOSTEL)

INCOMING

1 No. 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

03 No. 63 Amp FP RCBO.

04 No. 40 Amp TPN Miniature Circuit Breaker

02 No. 40 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

UPS PANEL-

INCOMING

1 No. 63 Amp DP Miniature Circuit Breaker

BUS BAR

100 Amp DP aluminium bus bar.

OUTGOING

02 Nos 40 Amp DP Miniature Circuit Breaker.

01 Nos 25 Amp DP Miniature Circuit Breaker.

1 Lot of control / power wiring.

Panel described as above

ELECTRICAL PANEL (COMMUNITY CENTRE)

INCOMING

1 No 63 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

100 Amp TPN aluminium bus bar.

OUTGOING

02 Nos 40 Amp TPN Miniature Circuit Breaker

04 Nos 25 Amp TPN Miniature Circuit Breaker

01 Nos 25 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

ELECTRICAL PANEL- COMMON AREA (TYPE-III, IV & V)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

100 Amp TPN aluminium bus bar.

OUTGOING

02 No 100 Amp FP Moulded Case Circuit Breaker

02 Nos 63 Amp DP Miniature Circuit Breaker

01 Nos 25 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

METER BOARD (TYPE-III)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

100 Amp TPN aluminium bus bar.

OUTGOING

EACH OUTGOING FEEDER SHALL HAVE DUAL SOURCE ENERGY METER.

04 Nos 63 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

METER BOARD (TYPE-IV)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

EACH OUTGOING FEEDER SHALL HAVE DUAL SOURCE ENERGY METER.

04 Nos 40 Amp FP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

METER BOARD (TYPE-V)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

EACH OUTGOING FEEDER SHALL HAVE DUAL SOURCE ENERGY METER.

04 Nos 63 Amp FP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

ELECTRICAL PANEL- (TYPE- V)

INCOMING

1 No 250 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

300 Amp TPN aluminium bus bar.

OUTGOING

06 No 100 Amp FP Moulded Case Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

ELECTRICAL PANEL- (TYPE- VI)

INCOMING

1 No 80 Amp FP Moulded Case Circuit Breaker

BUS BAR

100 Amp TPN aluminium bus bar.

OUTGOING

02 Nos 63 Amp TPN Miniature Circuit Breaker

02 Nos 40 Amp TPN Miniature Circuit Breaker

01 Nos 40 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

ELECTRICAL PANEL-1 (GUEST HOUSE)

INCOMING

1 No 200 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

250 Amp TPN aluminium bus bar.

OUTGOING

04 No 100 Amp FP Moulded Case Circuit Breaker

03 Nos 63 Amp TPN Miniature Circuit Breaker

05 Nos 63 Amp DP Miniature Circuit Breaker with Dual source energy meter

1 Lot of control / power wiring.

Panel described as above

ELECTRICAL PANEL-2 (GUEST HOUSE)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

04 No 63 Amp FP Moulded Case Circuit Breaker

02 Nos 63 Amp TPN Miniature Circuit Breaker

01 Nos 40 Amp TPN Miniature Circuit Breaker

01 Nos 25 Amp TPN Miniature Circuit Breaker

01 Nos 40 Amp DP Miniature Circuit Breaker

01 Nos 25 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

METER BOARD (GUEST HOUSE)

INCOMING

1 No 100 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

150 Amp TPN aluminium bus bar.

OUTGOING

EACH OUTGOING FEEDER SHALL HAVE DUAL SOURCE ENERGY METER.

08 Nos 63 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

LIFT PANEL (GUEST HOUSE)

INCOMING

1 No 63 Amp FP Moulded Case Circuit Breaker

1 No. Digital Multi Function Meter with CT's.

1 Set of phase indicating lamps with Single Pole MCB.

1 Set of ON / OFF indicating lamps with Single Pole MCB.

BUS BAR

100 Amp TPN aluminium busbar.

OUTGOING

02 Nos. 63 Amp FP RCBO.

03 Nos. 40 Amp TPN Miniature Circuit Breaker

02 Nos. 40 Amp DP Miniature Circuit Breaker

1 Lot of control / power wiring.

Panel described as above

MCCB BOXES

Supply, installation, testing & commissioning of MCCB in Sheet Steel enclosure made out of 2 mm thick CRCA sheet suitable for 3 phase 4 wire 50Hz AC system complete with four pole Moulded Case Circuit Breaker suitable for incoming & outgoing termination including power coating etc. complete as per specification & as required.

315 Amp FP MCCB

250 Amp FP MCCB

100 Amp FP MCCB

63 Amp FP MCCB

200 Amp FP MCCB

160 Amp FP MCCB

40 Amp DP MCB

ELE MAIN PANEL-1 -DG BACKUP (NEW BLOCK)

INCOMING

02 No. 630 Amp FP Moulded Case Circuit Breaker.

02 Set of phase indicating lamps with Protective SP MCB.

02 Set of ON / OFF indicating lamps with Protective SP MCB.

02 Set of Electronic KWH Meter with maximum demand recording facility.

BUS COUPLER

1 No. 500 Amp FP Moulded Case Circuit Breaker

BUS BAR

700 Amp TPN aluminium bus bar.

OUTGOING

01 No. 500 Amp TP+N Moulded Case Circuit Breaker.

02 No.200 Amp TP+N Moulded Case Circuit Breaker.

08 No.100 Amp TP+N Moulded Case Circuit Breaker.

06 No.63 Amp TP+N Moulded Case Circuit Breaker.

07 No. 63 Amp TPN Miniature Circuit Breaker.

Panel described as above

LIFT PANEL-1 (NEW BLOCK)

INCOMING

01 No. 100 Amp FP Moulded Case Circuit Breaker.

01 Set of phase indicating lamps with Protective SP MCB.

01 Set of ON / OFF indicating lamps with Protective SP MCB.

BUS BARS

150 Amp TPN aluminium busbar.

OUTGOING

04 No.63 Amp TP+N Moulded Case Circuit Breaker.

05 No. 40 Amp TPN Miniature Circuit Breaker.

01 No. 40 Amp DP Miniature Circuit Breaker.

Panel described as above

LIGHT PANEL-1 (NEW BLOCK)

INCOMING

01 No. 200 Amp FP Moulded Case Circuit Breaker.