ELECTRONICS EQUIPMENT

DSO (Digital Storage Oscilloscope) Bandwidth: 50 - 100 MHz. Sampling Rate: 1GS/s. Channels: 2 (minimum) Power Supply: 100V–240V AC, 50-60 Hz Automatic Measurement: Vpp, Vavg,RMS, Frequency, Period, Vmax, Vmin, Rise Time, Fall Time, + Width, - Width, +Duty, - Duty etc., Horizontal Scale: 5 ns/div – 100 ns/div or equivalent Vertical Resolution: 8 bits (2 Channels simultaneously) Vertical Sensitivity: 1 mV/div – 10 V/div (at input) Waveform Math: +, -, x , ÷, invert, FFT etc., Waveform Storage: 16 waveforms or equivalent Communication Interface: USB Host, USB interface. 7-inch color display or equivalent Basic trigger functions

Digital IC trainer kit With Breadboard 5V DC, 1A regulated power supply ±12V DC / ±15V, 200 mA regulated power supply Solderless breadboard to accommodate 8 × 16-pin ICs ZIF (Zero Insertion Force) IC sockets Supports TTL and CMOS ICs Logic IO LEDs for output monitoring 8 buffered LED outputs 8 debounced switch inputs TTL clock: 1 MHz Variable clock generator: 0.5 Hz to 50 Hz Single pulse output: 100 ms (buffered, positive and negative outputs) One seven-segment display with 4 BCD inputs Built-in logic probes Built-in logic switches Experiments on basic logic gates, flip-flops, counters, and multiplexers

Eliminator Transformer (stepdown) Input - 220V - 240V AC, 50 Hz, Output-2V to 12V DC, 0-2 A Ripple: <5mV

Decade resistance box Range: 1 Ω to 10 MΩ, steps: 1-10-100-1k-10k, accuracy ±1%, suitable for filter and oscillator experiments

DECADE INDUCTANCE BOX Range: 1 µH to 10 H, rotary switch selection, low loss inductors, accuracy ±1%, , suitable for filter and oscillator experiments

8051 Micro controller Kit Operating Voltage: +5V DC 4 KB Flash (AT89C51) / 8 KB Flash (AT89S52) RAM: 128 Bytes internal RAM 16×2 Alphanumeric LCD Push Buttons / Tactile Switches DIP Switches for digital input Inbuilt ADC Interface : LDR,POT Inbuilt DAC Interface Inbuilt Stepper Motor Driver With Stepper Motor Inbuilt DC Motor Driver with DC Motor 1X4 Led Array, 1 X4 Keypad, 1X Relay 1X Buzzer, 16X2 LCD Display, 1X PWM Driver 1X Hardware Interrupt Key, Inbuilt RTC Inbuilt EEPROM, Inbuilt UART Module 4X7 Segment Display, Both Assembly and C language programmable, PC Interfaceable.

Single Phase Induction Motor Single phase induction motor, 230V AC, 50Hz supply. Power rating 1 HP (0.75 kW). Speed 1440 RPM. Capacitor start/run type suitable for lab use Loading Setup portable ammeter and Digital Tactometer contact type

Auto Transformer Input - single-phase, 230V/240V, 50 Hz, 4A, AC Output - 0 to 270VAC, Class "H" or Class F insulation.

TEMPERATURE MEASUREMENT KIT Sensors: RTD (PT-100), Thermocouple (Fe-K/J-type), and/or Thermistor (NTC). Display: 3½ digit LED/LCD digital display (typically 200mV FSD). Temperature Source: Portable water kettle or heater block. Signal Conditioning: On-board circuitry for amplification, linearization, and cold junction compensation. Test Points: Multiple 2mm/4mm banana sockets for monitoring input/output signals. Power Supply: 230V AC, 50Hz, Single-phase. Accessories: Includes a glass thermometer, NTC thermistor probe 10k, K-type thermocouple probe, patch cords, and instruction manual.