| 1 | Compression Testing Machine -CTM | Servo Motor Based Automatic Compression Testing Machine -CTM 3000KN capacity with additional loading frame 1000KN capacity.3000KN with 10-point NABL Calibration with Least Count- 0.1KN ,Platen dia-300MM ROUND ram dia-272MM, ram travel-50MM,vertical daylight- 400MM horizontal daylight-400MM. 1000KN with 10-point NABL Calibration with Least Count- 0.1KN ,Platen dia-222MM ROUND ram dia-157 MM, ram travel-50MM,vertical daylight- 370MM horizontal daylight-260MM. System should have Load indication and Control-10.1 inch Coloured touch screen controller,System should have Pace rate controlling accuracy-5 percent, Digital Reading, Auto stop after failure of specimen- Available, machine stops after completion of test.Multi-Channel operation frame can be attached-3 channel operation possible, flexural and compression. System should have Auto Release of Pressure after specimen failure test, pressure release automatic after completion. System should have Pace Rate or Rate of Loading indication. System should have automatic Calculation of result.System should have Accuracy of 1 percent
System should have motorized Pumping and motor must be servo motor.System should have Saving of records of 2000 records with Pen drive. It must be USB slot for downloading data in Pen Drive. it should have Computer with minimum specification of 2 GHz Pentium Dual Core or equivalent, 4 GB RAM, although using multiple testing machines may require addition memory or, and a faster processor32- or 64-bit operating system type. 500 GB HD Drive , Mouse or pointing device and keyboard supported by windows, Monitor that support at least 1024 x 768 resolution ,Min. 2 USB Serial Port , Window compatible printer recommended for reporting capabilities, LAN Connectivity port.The equipment-machine must be NABL Traceable, Calibration certificate need to be submitted by NABL accrediated Lab. for details see technical specification Annexure A | 1 | Nos | Uttam Kumar Mishra 202001,NSIC Technical Services Centre A-1 Industrial Estate, Aligarh 202001 (Uttar Pradesh) | 21 |
| 2 | | Concrete Test Hammer Analog with NCCBM Calibration certificate .Ref. Std. - IS 13311 - 1992 -Part 2 & ASTM C805, D5873.The concrete test hammer must be used for the non-destructive testing of concrete. It must allow one to have a quick estimate of the strength of concrete. Since it should simply give an indication based on surface properties.
Measuring Range-10 to 70 N/mm2
Impact energy- 2.207Nm. for details see technical specification Annexure A | 1 | Nos | Uttam Kumar Mishra 202001,NSIC Technical Services Centre A-1 Industrial Estate, Aligarh 202001 (Uttar Pradesh) | 21 |
| 3 | | Proving Ring 1000KN With Dial Gauge - with NCCBM CALIBRATION CERTIFCATE- for details see technical specification Annexure A | 1 | Nos | Uttam Kumar Mishra 202001,NSIC Technical Services Centre A-1 Industrial Estate, Aligarh 202001 (Uttar Pradesh) | 21 |
| 4 | | Vicat Apparatus with ISI Certification Mark, IS-5513, fitted in Aluminum Box .The equipment must consist Vicat Mould, Glass Base Plate, Initial Needle -in Plastic Case,Final Needle -in Plastic Case-,Consistency Plunger -in Plastic Case,Mild Steel Base Plate, Vicat Mould Split Type, with Clamping Ring
for details see technical specification Annexure A | 1 | Nos | Uttam Kumar Mishra 202001,NSIC Technical Services Centre A-1 Industrial Estate, Aligarh 202001 (Uttar Pradesh) | 21 |
| 5 | | Sieve Shaker, Motorized, with Built-in Digital Timer -for 30cm dia sieves and 20 cm dia sieve
The assembly should consist of the following salient features- The design should be compact and light weight and should be such that it can be mounted on a bench top. This feature is required to eliminate the use of concrete foundation.
The model should operate at a reduced noise level. A digital timer adjustable from 0-99 minutes should be incorporated as an integral part of the equipment. The Sieve Shaker should allow provision of carrying up to 4-6 sieves of 30cm dia and 6-8 sieves of 20cm dia. The sieve shaker should be such that it can be driven by a 0.25 HP geared motor. The Sieve Table should be inclined suitably from the vertical axis and the direction of inclination should changes progressively in the clockwise direction. In addition to the gyratory motion of the table, there should also be a tapping motion as well. The assembly should be suitable for operation on 220 V, 50 Hz, Single Phase, AC supply. for details see technical specification Annexure A | 1 | Nos | Uttam Kumar Mishra 202001,NSIC Technical Services Centre A-1 Industrial Estate, Aligarh 202001 (Uttar Pradesh) | 21 |
| 6 | | 1. G.I Sieve 450mm
Reference Standards - IS 460, IS 2720 (Part IV)
Sieves should be of 450 mm diameter -frame size-GI frame-perforated plates sieves with aperture sizes of 2 mm,2.36mm,4.75mm, 10mm, 12.5mm, 25mm,31.5mm,40mm,63mm, 75mm, 80mm,90mm and Cover and Pan-1 each.
2. G.I Sieve 300 mm.
Reference Standards - IS 460, IS 2720 -Part IV
Sieves should be of 300 mm diameter -frame size--GI frame-perforated plates sieves with aperture sizes of 2 mm,2.36mm,4.75mm, 10mm, 12.5mm, 25mm, 31.5mm, 40mm,63mm,75mm,80mm,90mm and Cover and Pan-1 each. for details see technical specification Annexure A | 24 | Nos | Uttam Kumar Mishra 202001,NSIC Technical Services Centre A-1 Industrial Estate, Aligarh 202001 (Uttar Pradesh) | 21 |
| 7 | | Brass Sieves 200 mm
Reference Standards - IS 460, IS 2720 (Part IV) Sieves made of brass with 20cm (diameter) frame size with 2.36mm, 1.18mm, 600 microns, 300 microns, 150 microns, 90 microns and 75 microns aperture size along with Cover and Pan for the same-1 each1. for details see technical specification Annexure A | 8 | Nos | Uttam Kumar Mishra 202001,NSIC Technical Services Centre A-1 Industrial Estate, Aligarh 202001 (Uttar Pradesh) | 21 |
| 8 | Slump Test Apparatus with testing rod and base plate | Slump Test Apparatus with testing rod & base plate
Ref Standards IS-7320, BS- 1881, ASTM C 143, AASHTO T119
This test should be suitable for cohesive and plastic mixes of concrete containing aggregate smaller than 50 mm.
The setup should consist of following salient features-
Base should have cleats on its underside to help dig into the ground surface.
Should allow positive clamping of slump cone to the base while filling and tamping the concrete. A combination swivel carrying handle should be such that it serves as the datum so that direct measurements can be made using the markings on the tamping rod itself.
for details see technical specification Annexure A | 1 | Nos | Uttam Kumar Mishra 202001,NSIC Technical Services Centre A-1 Industrial Estate, Aligarh 202001 (Uttar Pradesh) | 21 |
| 9 | | Tamping Rod 16x600mm Graduated.
Tamping Rod, Steel, 16mm dia x 600mm length with ISI Certification Mark, IS-10086. for details see technical specification Annexure A | 2 | Nos | Uttam Kumar Mishra 202001,NSIC Technical Services Centre A-1 Industrial Estate, Aligarh 202001 (Uttar Pradesh) | 21 |
| 10 | | Cube Moulds for Concrete -IS- 10086- 14kg weight approx.
With ISI certification mark, 150mm along with a Tamping rod-600mm length and 16 mm diameter . for details see technical specification Annexure A | 4 | Nos | Uttam Kumar Mishra 202001,NSIC Technical Services Centre A-1 Industrial Estate, Aligarh 202001 (Uttar Pradesh) | 21 |
