Provn of covered shed for refuse disposal bins at NOFRA I Provn of storage shed adjacent to bldg P 8 at MO Goa and Provn of water pipeline from STP to common areas at NOFRA II under GE Gomantak

Amount

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/disintegrated rock.

M&L PCC Cement concrete type D2 (1:4:8) 40mm graded aggregates as in foundations, filling and mass concrete.

M & L CRS bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

All as per item No 03 above but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surface of concrete, square, rectanguler etc

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. rough finised surface of concrete, square, rectanguler etc

Use and waste of formwork to sides of pillars, posts, struts, piers, columns, and stanchions, rough finised surface of concrete, square, rectanguler etc.

Formwork to soffits of suspended slabs such as chajjas n.exc 200 mm thick (Horizontal or sloping)

M & L RCC (design mix) M-30 (20mm graded aggregates) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete

M & L RCC ((design mix) M-30(20mm graded aggregates) in Columns, pillars, piers, posts and struts

M & L RCC (design mix) M-30 (20mm graded aggregates) in Beams, cantilevers, bressummers, lintels over 1.5m span

M & L RCC (design mix) M-30(20mm graded aggregates) in Chajjas& slab etc.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m soft/disintegrated rock.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm

M & L Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured)

M & L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

M & L Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

M & L Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall

M & L for precast cement concrete block masonry with solid block exc 10 cm in width and setting in CM (1:6) 1:3:6 type C-1 using 20mm graded stone aggregate.

M & L Rendering 10 mm on concrete surfaces in CM 1:4 finish even and smooth without using extra cement.

Material and Labour for rendering 15mm thick (in two coats of 10mm under coat and 5mm finishing layer) on fair faces of brick work/stone or concrete surfaces in cement mortar 1:4 finished even and fair without using extra cement for both coats mixed with integral water proofing compound at the rate of 3% by weight of cement all as per manufactures instructions incl necessary scaffolding etc complete. (Note : Water proofing compound shall be measured and paid separately)

M&L for rendering 5mm thick cement plaster with cement mortar(1:3)on concrete surface as in ceiling finished even and smooth without using extra cement.

Supply only Integral waterproofing compound.

M & L Hardcore with broken stone or boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.

M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering

M & L 75 mm thick PCC (1 : 4 : 8) type D2 (using 40mm graded aggregate) Cement concrete as in Sub base of flooring

M & L 75 mm thick PCC (1 : 3 : 6) type C2 (using 40mm graded aggregate) Cement concrete as in plinth protection.

Screed bed or bedding layer of mortar 20mm thick(1:4) for laying floor finishes

M/L Virtified tiles light shade 9 to10mm thick (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm ,in floor and skirting etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match

S&F aluminium powder coated frame and shutters for windows/ventilators sliding/fixed/openable type complete with necessary fittings such as two concealed lock for each window, roller etc and fixing all as speciefied and directed by Engineer-in-Charge. Note : Weight of aluminium three track section and tubes for windows/ventilators shall not be less than 0.55 Kg/RM and not more than 1.00 Kg/RM. Note : (a) The weight of rubber gasket beading will not be measured with the weight of aluminium shutters, glass will be measuerd and paid separatelly. (b) The rate quoted by the contractor shall also include necessary wheels for sliding shutters and hinges for side hung/top hung shutter as required at sight and concealed locks for windows. (c) The colour of powder coating shall be as approved by GE.

S&F glazing with 4 mm thick sheet glass ordinary type including rubber beddings/gasket around glass panes all as specified.

S&F glazing with 6.3 mm thick sheet glass ordinary type including rubber beddings/gasket around glass panes exc 0.50 Sqm in each pane all as specified.

S&F aluminium anodised wire mesh of size 1.5 mm x 3 mm mesh 20 Gauge thick of make M/S Kiran Netting or equivalent as approved by GE.

S&F aluminium powder coated grill of make DG 104 (10 mm thick section) and mess size of 80mm x 60mm including 'F' channel alround grill.

S&F for aluminium (Extruded) Body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

S&F aluminium anodised handle of size 150mm, "D type" complete all as specified and directed.

S&F aluminium anodised BARREL tower bolt 200mm long of extruded section complete all as specified and directed.

S&F stainless steel Butt hinges 75mm long galvanised mild steel hing pin type C-21 complete as specified and directed.

S&F brass mortice lock , vertical type of size 100mm (4 levers).

M&L for laying water proofing treatment using 4mm thick APP modified mambrene consisting five layer membrences with features as specified weinghing not less than 3.5 kg/sqm reinforced with woven polyester fiber @ 160gm/sqm laid over a coat of cold applied bituminus primer @ 0.40kg/sqm by torching the membrence and sealing the over lap by 100mm length side and 150mm width side all as per manufacturer instructions including joints and changes in direction be covered with cement mortar 1:3 mixed with SBR latex@ 200ml per bag of cement or as per manufacturer instructions and to the satisfaction of Engr-in -charge.(Note :(i) Irrespective of lap the net covered area shall only be measured for payment. (ii) Quoted rate shall be inclusive of APP membrene, SBRlatex and applying a coat of bituminous aluminium paint @ 200gm/sqm (min) in two coat .

M&L for two coats of Nitobond EP @4.5kg /10sqm each coat on old surfaces of slab for bonding with new concrete including cleaning brooming and washing old surfaces

M&L for preparation of new untreated surfaces of walls and apply two coat of Oil bound Distemper to walls.

M&L for applying two coats of acrylic emulsion exterior paint (anti fugal paint- APEX)Ultima or equavalent over a coat of acrylic emulsion exterior primer including preparation of new plastered surfaces of walls complete all as specified and directed.

M& L for preparation of New untreated surfaces and apply three coat of white wash on ceiling.

Surface excavation n. exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in soft/disintregrated rock

M & L Machines pressed precast concrete interlocking paver block gloss finished coloured any shape and size confirming to M-50 grade(100mm thickness).

Excavation in trenches nexc 1.5 m wide and n.exc 1.5 m in depth, for foundation etc n.exc 1.5 m 10 Sqm on plan and n.exc 1.5 in depth as in hard/dense soil and getting out.

M & L for 100 mm thick PCC type B-2, (1:2:4) (using 40 mm graded aggregate) as in Hardstanding.

Expanded metal, cut to length, bent to shap requered and tying with and including annealed mild steel wire not less then 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steelmembers.n,exc,for 4 kgs.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates. Fe-410-W(Gde-E-250) quality-B)

M&L for two coat of synthetic enamel paint on steel surfaces including preparation of new steel surfaces over a coat of red oxide zinc chrome primer, over 10 cm in width or girth, not other wise described.

M & L Angle iron 50x50x6 mm and flat iron 25x6mm for post & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc including all necessary drilling, bolting or reveting, etc conforming to Fe-290 Gde E-165.

M&L for MS screws and bolts (machine made) 11 to 15mm dia, with hexagonal or square heads at one end and screwed the other or screwed both ens each screwed end to be fitted with washers and one hexagonal or square nut, nexc 5cm long.

S & F 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screw and washers, in roofs, walls etc with grade of zinc coating 275

M&L forming construction (Dummy) joints 65 mm deep x 10 mm wide filled with sealing compund Grade "A".

M & L for applying three coats of white wash including preparation of newly plastered surfaces of wall.

M & L for PCC 1:2:4 type B-2 (40mm graded aggregate) in foundation filling and mass concrete.

Supplying, laying and testing complete GI tubing medium grade 50mm bore ISI marked with all (ISI marked )fitting laid in trenches complete all as specified and directed.

M&L for 20mm bore steel water tubing medium grade (ISI marked)galvanised with and including all tube fitting (ISImarked)concealed or to wall ceiling or laid in floor complete all as specified.

S & F 20 mm dia stop valve /angle cock ,castcopper,alloy screwed down high pressure fancy type ,chromium plated,screwed both ends for iron pipe or union complete all as specified and directed.

S & F 15mm dia bip tap,castcopper,alloy screwed down high pressure fancy type ,chromium plated,screwed both ends for iron pipe or union complete all as specified and directed.

M&L for chequrred cement concretetiles 20cm x20cm x25mm thick set,jointed and pointed in neat cement slurry in floors .

M&L for one light point or fan point controlled by one switch with cables 1.5 Sqmm copper cable FRLS multistranded unsheathed drawn through & including concealed PVC conduit and 1.5 sqmm conductor cable for earth wire including making connection with common earth and earth dolly including pressed steel terminal al boxes concealed in wall with 3 mm thick plastic laminated sheet top cover fixed with brass screw for mounting switches sockets regulator etc all as per directed by Engr-in-Charge.

M&L for one light point or fan point controlled by one switch with cables 1.5 Sqmm copper cable FRLS multistranded unsheathed drawn through & including casing and caping and 1.5 sqmm conductor cable for earth wire including making connection with common earth and earth dolly including pressed steel terminal al boxes concealed in wall with 3 mm thick plastic laminated sheet top cover fixed with brass screw for mounting switches sockets regulator etc all as per directed by Engr-in-Charge.

M&L for point wiring for 5 amp independant point with 1.5 sqmm copper wire & 1.5 sq mm copper wire as earth lead drawn through & including concealed PVC conduit of suitable size.

M&L for point wiring for 5 amp independant point with 1.5 sqmm copper wire & 1.5 sq mm copper wire as earth lead drawn through & including casing and caping of suitable size.

M&L for point wiring for 15 amp independant point with 4 Sqmm copper wire & 4 Sqmm copper wire as earth lead drawn through & including concealed PVC conduit of suitable size.

M&L for point wiring for 15 amp independant point with 4 Sqmm copper wire & 4.5 Sqmm copper wire as earth lead drawn through & including casing and caping of suitable size.

Supply & fixing switch piano flush button single pole, one way, 5 Amps.

Supply & fixing switch socket combination outlet 3 pin 5 Amps flush type.

Supply & fixing switch socket combination 2 in 1, 3 pin 5 and 15 Amps flush type.

Supply & Fixing ceiling rose, surface Bakelite 65x50 mm Two to three terminals

Supply & Fix in repair MCB 6 to 32 Amps, Single Pole, braking capacity 10KA, B curve (ISI Marked).

Supply & Fix in repair MCB 32 Amps, SPN, braking capacity 10KA, C series complete all as specified and directed.

Supply & Fix MCB 32 Amps, Triple Pole Neutral, braking capacity 10 KA C curve (ISI Marked).

Supply & Fixing sheet metal enclosure DB, 8 way, SPN, single door factory made powder coated including neutral/earth connector, fixed in wall complete all as per specified and directed by Engr-in-Charge.

Supply and fix sheet metal enclosure for MCB DB, 8 way, triple pole and neutral, 415 volts, double door with 250 Amps rated bus bar complete all as specified and directed.

Supply & Fixing of sheet metal enclosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB 20 Amps.

Supply and Fixing LED tube light fitting surface mounted integrated type with 20 watts LED having minimum 100 lumens/watt complete including dismantling old fittings all as specified and directed.

Supply & Fixing fan regulater electronic step type 120 watt 280 volt including removal of old one complete.

Supply & fixing ceiling fan 1200mm sweep (ISI marked), 230 volts, (BEE rating 5 star) with connecting rod of length upto 2 mtr complete.

Supply & Fixing Submain wiring with 2.5 sqmm three runs of single core multi stranded FRLS unsheathed PVC copper conductor cable 1100 Volts as per colour code drawn in through concealed PVC conduit including all accessories as required and connecting to Existing main switch board/DB & testing on completion including dismantling old unserviceable submain wiring complete.

Supply & Fixing Submain wiring with 4 sqmm three runs of single core multi stranded FRLS unsheathed PVC copper conductor cable 1100 Volts as per colour code drawn in through concealed PVC conduit including all accessories as required and connecting to Existing main switch board/DB & testing on completion including dismantling old unserviceable submain wiring complete.

Supply & Fixing Submain wiring with 4 sqmm three runs of single core multi stranded FRLS unsheathed PVC copper conductor cable 1100 Volts as per colour code drawn in casing capping including all accessories as required and connecting to Existing main switch board/DB & testing on completion including dismantling old unserviceable submain wiring complete.

M&L earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to GI wire 4mm dia by means of bolts, nuts, check nuts & washers of GI or steel, and earth lead connected to main DB panel/meter box panel including necessary earth work and excavation of in any type of strata, chamber in PCC 1:2:4 type B-2 with CI cover, GI tubing 15mm dia light grade for protection of GI wire, GI tubing 20mm dia for watering etc all as per electrical plate no 5 of SSR part-I including provision of earthing test point & connecting to electrical equipments and testing on completion.

Supply & Fix under ground cable XLPE insulated armoured heavy duty 1100 volts grade of size 16 Sqmm 2 core conforming to IS 7098 Part-1 1988 with aluminium conductor multistandarded including centre gland, lugs, jointing materials etc laid in trenches or fixed it to wall complete all as specified and directed by Engr-in-Charge.

Supply & Fix under ground cable XLPE insulated armoured heavy duty 1100 volts grade of size 25 Sqmm 3.5 core conforming to IS 7098 Part-1 1988 with aluminium conductor multistandarded including centre gland, lugs, jointing materials etc laid in trenches or fixed it to wall complete all as specified and directed by Engr-in-Charge.

Supply & Fix under ground cable XLPE insulated armoured heavy duty 1100 volts grade of size 150 Sqmm 3.5 core conforming to IS 7098 Part-1 1988 with aluminium conductor multistandarded including centre gland, lugs, jointing materials etc laid in trenches or fixed it to wall complete all as specified and directed by Engr-in-Charge.

M/L for sand cushion in trenches for cable protection complete all as directed and specified.

Supply and lay PCC cable cover class LV type 1 flat size 250mmx150mmx40mm. Make : Mehtab/National/Topaz

M&L for fixing GI tubing 40mm dia light grade use for the protection of cable all as specified and directed by Engr-in-Charge.

Supply and laying of High density poly-ethylene pipes (HDPE) 40 mm dia, pressure rating 6 kgf/sqcm laid in trenches as per direction of Engr-in-Charge.

M & L Cable jointing kit for 1.1 KV grade cable for straight through heat shrink type joint complete with jointing material and accessories suitable for 3.5 core XLPE armoured aluminium conductor cable of size 150 sqmm including dismantling old burnt cable joint termination.

M & L for shifting of existing LT Panel upto and not exceeding 15 mtr refixing and connecting all cables and testing on completion.

M/S DUBAL CONSTRUCTION

M/S. M M S ENTERPRISES

M/S jvsr constructions