Interior Fit-Out-Renovation works in the office space of Ministry of Mines , 9th Floor -Half portion at LIC Building, Connaught Place, New Delhi

GENERAL ABSTRACT OF COST

Name of Work : INTERIOR/ FURNISHING WORK OF MINISTRY OF MINES, 9TH FLOOR, LIC BUILDING, NEW DELHI.

Sub Head No. Description DSR NDSR/MR Total

CHAPTER-1 CIVIL WORK 50,828.55 0.00 50,828.55

CHAPTER-2 CLADDING WORK 2,534.67 62,229.74 64,764.41

CHAPTER-3 DOOR & WINDOW WORK 22,538.57 298,846.71 321,385.29

CHAPTER-4 FLOORING WORK 40,777.46 757,853.09 798,630.55

CHAPTER-5 CEILING WORKS 230,858.85 665,703.10 896,561.95

CHAPTER-6 WALL FINSHES WORK 1,292,642.61 2,706,576.74 3,999,219.36

CHAPTER-7 REPAIRS TO BUILDING 13,448.81 0.00 13,448.81

CHAPTER-8 METAL WORK 44,530.32 0.00 44,530.32

CHAPTER-9 OTHER WORKS 0.00 340,812.50 340,812.50

CHAPTER-10 FURNITURE WORK 0.00 6,894,760.00 6,894,760.00

CHAPTER-11 PLUMBING WORK 84,131.42 183,830.00 267,961.42

CHAPTER-12 ELECTRICAL WORK 2,037,132.00 1,020,417.15 3,057,549.15

CHAPTER-14 Audio And Vedio System (AV) 5,068,083.15 5,068,083.15

CHAPTER-15 Active And Passive 1,972,819.00 1,972,819.00

CHAPTER-17 FIRE ALARM SYSTEM 519,358.00 249,260.00 768,618.00

CHAPTER-18 FIRE FIGHTING 0.00 82,357.90 82,357.90

Total value including GST 28,507,177.00

Digitally SERVICES LIMITED

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF MINISTRY OF MINES, 9TH FLOOR, NEW DELHI

ABSTRACT OF COST

NAME OF WORK -INTERIOR AND FINISHING WORK

I.NO DSR 2023/MR DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

SH 1 CIVIL WORK DSR Amount (After

1 1.1.18 Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by Cum 20 494.1 9882 9615.186

mechanical transport including loading, transporting, unloading to approved municipal dumping ground for all

lifts, complete as per directions of Engineer-in-charge.

Note - item to be applicable in urban areas having directions for restricted hours for movement/ plying of load

carrying motor vehicle of 3.5 cum or more.

2 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and Cum 5.00 7878.5 39393 38329.389

shuttering 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate

20 mm nominal size derived from natural sources)

3 6.13.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in Sqm 2.00 1123.8 2248 2187.304

superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

4 13.4.1 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) Sqm 2.00 357.75 716 696.668

Total Carried Over to Abstract for Sub Head: 1.00 Civil Work : 50828.55 0.00

SH 2 CLADDING WORK

1 MR-1 Providing and fixing 12 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for Sqm 0.40 5116.46 2026.12

kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade,

colour and texture laid over 18 mm thick thick HDMR ply board, joints treated with white cement, mixed with

matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high

gloss finish etc. complete at all levels.. Granite stone slab including machine polishing to edge to give high

gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work Base rate 180 Sqft

2 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., Metre 1.32 510.95 674.00 655.802

3 8.4 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width Metre 1.32 568.95 751.00 730.723

upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

4 8.5 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity Each 1.00 978.70 979.00 952.567

counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc.

including moulding, rubbing and polishing of cut edges etc. complete.

5 8.6 Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish Sqm 0.40 506.70 201.00 195.573

complete.Base rate 300Sqft

6 MR-2 Providing and fixing Ist quality vitrified wall tiles conforming to (thickness to be specified by the Sqm 17.82 3378.43 60203.62

manufacturer), of approved make, in all colours, shades of any size as approved by Engineerin- Charge, in

skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and

jointing with grey cement slurry @ 3.3kg per sqm, including pointing in epoxy grout of matching shade

complete. size of tiles 1200mm x 2400 mm BASE 170

Total Carried Over to Abstract for Sub Head: 2.00 Cladding Work : 2534.67 62229.74

SH 3 DOOR & WINDOW WORK

1 9.1.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and Cum 0.06 142949.7 7980 7764.54

fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash

fastener shall be paid for separately). Second class teak wood

2 9.112 Providing and fixing 2nd class teak wood lipping/ moulded beading or taj beading of size 18X5 mm fixed with Metre 11.17 102.15 1141 1110.193

wooden adhesive of approved quality and screws/nails on the edges of the Pre-laminated particle board as per

direction of Engineer-in-charge.

3 9.20.1 Providing and fixing marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block Sqm 4.04 3473.85 14043 13663.839

board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical

grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless

Steel butt hinges with necessary screws

4 MR-3 Providing and Fixing 240 mm lock body for wooden doors of approved make and model all complete as per Each 2.00 1917.14 3834.28

the direction of Engineer-in-charge.

5 MR-4 Providing and Fixing 60 mm Ultero Cylinder 1CK Antique Brass Cylinder One side knob and one side regular key Each 2.00 1602.87 3205.74

for wooden doors of approved make and model all complete as per the direction of Engineer-in-charge.

6 MR-5 Providing and Fixing Rose Handle Antique Brass for Store, of approved make and model all complete as per the Each 2.00 3949.10 7898.20

direction of Engineer-in-charge.

7 MR-6 Providing and Fixing Concealed Door closer T660 -60 kg (CE certified) for wooden doors of approved make and Each 2.00 7340.68 14681.36

model all complete as per the direction of Engineer-in-charge.

8 MR-7 Providing and Fixing SS 304 Hinges Four Ball Bearing 100x75x3 mm (with screws) for wooden doors of Each 8.00 487.83 3902.64

approved make and model all complete as per the direction of Engineer-in-charge.

9 MR-8 Providing and Fixing 300x15x15 mm ss 304 Tower bolt -Square Type with screw for Wooden Doors of Each 2.00 1765.48 3530.96

approved make and model all complete as per the direction of Engineer-in-charge.

10 MR-9 Providing 32x840 mm 2813 SS 304 H type pull Handle for wooden doors. Material : Stainless Steel. Finish : Set 2.00 3281.24 6562.48

Satin Stainless Steel (SSS). of approved make and model all complete as per the direction of Engineer-in-

11 MR-10 Providing Half moon door stoper floor mounted. Material : SS Finish : AB. of approved make and model all pcs 2.00 754.98 1509.96

complete as per the direction of Engineer-in-charge.

12 MR-11 Providing and Fixing 240 mm lock body Antique Brass (8489) for wooden doors of approved make and model each 2.00 1917.64 3835.28

all complete as per the direction of Engineer-in-charge.

13 MR-12 Providing top and Bottom Strap/Door Pivot for wooden doors of approved make and model all complete as set 2.00 705.03 1410.06

per the direction of Engineer-in-charge.

14 MR-13 Providing & Fixing of Partition Glass Door having SG75 Door Frame with 6003 grade duly Anodized Aluminium nos 3.00 60442.14 181326.42

Sections having sizes of 75x35x2mm thick, Glass door with 10 mm Toughened Glass including Hafele/Dorma

XLC Door Closure, Hinges, SS Handle (H Type 300mm), SS Bottom Lock, Silicone/Thermoplastic Gaskets &

15 MR-14 Providing and fixing flutted glass in partitions etc. with EPDM rubber / neoprene gasket etc. complete as per sqm 12.39 5419.64 67149.34

the architectural drawings and the directions of engineer-in-charge . Toughened glass 10 mm thickness

Total Carried Over to Abstract for Sub Head: 3.00 Door & Window Work : 22538.57 298846.7146

SH 4 FLOORING WORKS

VITRIFIED FLOOR TILES

Digitally signed by AMITNSL

1 Providing and laying vitrified tile flooring with 3mm Spacers CM 1:4 (1 Part Cement: 4 Part M Sand) of 20mm

average. vitrified tiles of approved shade & laying pattern as per drawing in flooring with 3mm spacer joints,

laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) / Tile adhesive by weber / approved

equivalent make, including grouting the joints with graphite grey epoxy resin based grout PPDG-05 of AGL /

Myk make or equivalent and matching pigments, etc. with water absorption less than 0.08%and conforming to

IS:15622, of approved, make, in all colors and shades cleaned & washed with a suitable effective Cleaning

agent or any suitable means as per instructions of EIC, covering to protect tile with 275 GSM – 2 mm thick

Floor guard make or equivalent, joints to be taped, should remain intact till handing over, removed & disposed

of out of the site after completion, etc., complete. The rates quoted shall include the Rate required to lay the

tiles at the proper level if required, the Rate & cutting of tiles for laying borders/ patterns, etc, complete in all

respects as per details. Double charge vitrified tile polished finish of size

Digitally signed by AMITNSL

c MR-17 Glazed Vitrified tiles Matt/Antiskid finish of Size of Tile 600 x 600 mm sqm 3.17 1856.10 5880.12

2 11.48.4 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic sqm 240.168 174.5 41909 40777.457

coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and

finishing complete as per direction of Engineer-in-charge. Size of Tile 1000x1000 mm

3 MR-18 Providing and fixing Engineered wooden flooring 15 mm up to 3 mm top layer, core layer pine wood oak sqm 10.00 6168.00 61680.00

finish or equivalent with necessary T- profile and reducer fixing with underlayer 2 mm thick High Density

polyurethane foam having density of approx. 90 kg/cum and 2 mm thick rubber sheet as per manufacureres

specifications including IPS flooring as directed by engineer in charge. base price 350sqft

4 MR-19 Providing and fixing 100x15mm thick Polished wooden skirting of matching shade of wooden flooring . The Rm 55.55 0.00

skirting shall be fixed over commercial ply base to match the line and level of paneling. Complete as per

manufacturer's specification nd as directed by engineer in charge.

5 MR-20 Providing and laying Carpet plank/ tiles of Yarn type 100% Nylon; Multi-Level Pattern Loop, manufactured sqm 17.00 4571.00 77707.00

using 100% solution dyeing process, Tiles of size 50cm x 50cm / 25cm x 100cm equivalent as per direction of

EIC and site requirement with SSP® Soil Protection treatment ™ or equivalent containing properties of Stain

Repel, with - pro care backing, pro care self guard, procare fiber with recycled content, made from

thermoplastic with commercial very heavy , Class B1, TVOC Release amoutn A level < 0.500mg/m2h Radiant

Panel class 1rated ( ASTM E648), NBS smoke < 450, Pill test -Passed, Anti Static Property less Than 3.5

kv, Texture Appearance Retention Rating of 3.5 for Severe Use, Anti Microbial Treatment-Passes (AATCC-174).

CRI Green Label Plus is certified for indoor air quality, including fixing/ installation with Low/ Zero VOC content

Adhesive. Impact Sound (ISO 10140-3) 20 dB & Sound absorption (ISO 354) Basic Rate 275 Sqft

6 MR-21 Supply of 100 mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thichness 1.30 Rm 53.88 360.00 19396.08

to 1.50 mm. Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket.

Digitally signed by AMITNSL

Total Carried Over to Abstract for Sub Head: 4.00 Flooring Works : 40777.46 757853.0948

SH 5 CEILING WORKS

PLAIN GYPSUM BOARD CEILING

1 12.45.1 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sqm 175.00 1355.80 237265.00 230858.845

sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side

inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27

mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x

50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required

length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick

bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to

centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out

of 2.64 mm dia x 230 mm long G.I. wire at every junction,

including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry

wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with

the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish

of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing

with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer

suitable for board, all as per manufacturer's specification and also including the cost of making openings for

light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per

drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS

certification marks)

2 MR-22 Providing and fixing suspended ceiling in recessed grid system - 600 x 600 x12.5mm with Unity 4mm holes, c/c sqm 70.00 2095.33 146673.10

10 mm with upto 0.8 NRC. Material: Perforated plasterboard ,Board type: Ceiling tileOF SIZE Length x width x

thickness: 600X600X12.5mm ,Edge: E+, recessed grid system ( 8mm recess),Perforation: Unity 4mm Surface:

Water-based acrylic paint,Colour: White NCS 0701 Y24R, RAL 9003; gloss 5, Attachment: 15 or Silhoutte T-grid

system Edge section: 20x24 mm angled profile, 15+15 x 8+25 mm cornice moulding

Suspension: Recessed grid system

• Distance between hangers ≤ 1200mm

• Distance from wall to first hanger in direction of load - bearing section ≤ 400mm

• Distance between load bearing sections ≤ 1200 mm.

• Distance from wall to first load - bearing section ≤ 600 mm

• Sub-division executed with cross - sections length 1200 and 600 mm

• Screw spacing for attachment of edge sections length 1200 and 600 mm

• Light sockets of upto 3.0 kg can be integrated directly into the ceiling tiles. In the case of heavier fittings,

load must be taken up directly by the concrete deck or via the grid systemand extra hangers.

Fire rating: A2-s1,d0k

3 MR-23 Providing and fixing Veneer finished ceiling feature made of 19mm commercial board and all exposed surfaces sqm 35.00 5806.76 203237

finished in 4mm thick veneer of approved shade including framing, all fixing hardware, accessories, making

cove, cutout for light fixtures and any other incidentals which may require to secure to false ceiling and to

accomplish the work in all respect as per detail drawings and as directed & approved by architect. Rate quoted

to include vertical drops, making cove and all cut-outs required for light fixtures and other services cut-outs

and necessary supports with hitech rods from the true ceiling complete as directed by Architect. BR of Veneer

4 MR-24 Providing and fixing suspended acoustic ceiling in visible, but flush grid system ( with technical panel ) 300 x sqm 17.50 4245.34 74293

1200 x12.5mm flush grid system with high grade, glass fibre reinforced, acoustic, white painted, gypsum tile

with acoustic perforation as Unity Round 4mm c/c 10mm with NRC upto 0.8 . Material: Perforated

plasterboard Board type: Ceiling tile Length x width x thickness: 300X1200X12.5mm Edge: E, recessed grid

system ( 8mm recess)

Perforation: Unity 4mm round

Perforation percent: 11.0%

Surface: Water-based acrylic paint

Colour: White NCS 0701 Y24R, RAL 9003; gloss 5

Attachment: 15mm T-grid system

Edge section: 20x24 mm angled profile, 15+15 x 8+25 mm cornice moulding

Suspension: Recessed grid system

• Light sockets of upto 1.0 kg per sqmtr can be integrated directly into the ceiling tiles.

5 MR-25 BAFFLE CEILING : Providing & Installation of Baffle ceiling system comprises of 50 mm x 100 mm sqm 35.00 6900.00 241500

(50 mm width & 100 mm Height) U Shape panels in RAL color finish. Panels shall be made of 0.5 mm

thick galvanized steel after Powder-coated and length up to 4000 mm. Panel shall be high corrosion

resistance and good color stability. Centre to Centre panel gap will be 150 mm. Panels are fixed on to

roll formed carriers 20 mm wide x 40 mm deep out of 0.80 mm G.I sheet Powder-coated color with

cutouts to hold the panels in module of 50 mm at maximum 1200 m c/c. Carriers are suspended from

the roof or truss by 6 mm dia. galvanized steel wire rod hanger with special height adjustment

suspension clip at max. 1200 mm c/c. Hangers are fixed to the roof by ‘J’ hooks or ceiling brackets

and nylon inserts. Panels are factory cut in lengths up to maximum 4.0 m to suit site dimensions or

shop drawings. Top cap and side cap are used to cover the edges of the panels.

Total Carried Over to Abstract for Sub Head: 5.00 Ceiling Works : 230858.85 665703.10

SH 6 WALL FINSHES WORK

1 9.105.2 Poviding and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing Sqm 43.00 1818.15 78180.45 76069.57785

and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120

gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32

mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash

fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and

the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically

within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia

bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor

fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre,

Digitally signed by AMITNSL

and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling

channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5

mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat

head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing

tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for

board as per manufacture's specification and direction of engineer in charge all complete. 75mm overall

thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming

to IS: 2095: (part I): 2011 (Board with BIS certification marks)

2 MR-26 Poviding and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing Sqm 155.00 1283.33 198916.15

and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120

gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32

mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash

fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and

the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically

within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia

bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor

fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre,

and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling

channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5

mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat

head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing

tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for

board as per manufacture's specification and direction of engineer in charge all complete. 75mm overall

thickness partition

3 MR-27 Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer Sqm 310.00 1480.61 458989.10

on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in charge (Frame

work shall be paid for separately). 12 mm thick commercial ply conforming to IS : 1328 BWR type

4 MR-28 Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer Sqm 139.50 1080.61 150745.10

on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in charge (Frame

work shall be paid for separately). 8mm thick commercial ply conforming to IS : 1328 BWR type

5 MR-29 Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved primer Sqm 77.50 1021.74 79184.85

on one face, and fixed on wooden/ steel frame work, complete as per direction of Engineer-in-Charge 6 mm

thick commercial ply conforming to IS : 1328 BWR type

6 MR-30 Providing and fixing plain lining with necessary screws/ nuts & bolts/ nails, including a coat of approved primer Sqm 48.83 962.87 47012.13

on one face, and fixed on wooden/ steel frame work, complete as per direction of Engineer-in-Charge 6 mm

7 8.28.1 Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain Sqm 62.00 1946.25 120668.00 117409.964

lining / cladding with necessary screws, including priming coat on unexposed surface with : Decorative veneer

facings of approved manufacture

8 9.127.2 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish Sqm 248.00 897.30 222530.00 216521.69

with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046

Type S, including cost of adhesive of approved quality.

9 MR-31 LACQUERED GLASS: Providing and fixing of 6mm thick annealed SGG Planilaque Evolution Sqm 10 5500.00 55000.00

(premium GRIHA rated lacquered glass from Saint-Gobain) of approved color by Architect/ Client /

Customer, fixed with SGG ULTRAFIX (compatible neutral core silicon/ double sided tape) on a

perfectly leveled 12mm thick water proof marine plywood / MDF / Mineral fibre board which is

mounted on the RCC wall/any other structure. Lacquered glass must be made industrially (via curtain

coating process); opaque (if viewed against a support wall), coated with PU lacquer (50 micron thick);

color consistency (measured by Minolta spectrophotometer CM5081); highly durable (passes

PERSOZ hardness test for minimum 220 oscillatios); humid resistant (conforms to BS EN 1036 1999);

environmentally friendly (no lead, no arsenic, no copper, noformaldehyde); appropriate recycled

content (12% post industrial/ 6% post consumer); compressive strength (1000 MPa) & tensile strength

(40 MPa), same as float glass;

10 MR-32 providing and installation of ACOUSTIC WALL PANELS. The MDF wall panels shall be composed of Medium Sqm 45.00 6044.21 271989.00

Density Fiber board (MDF) with a minimum density exceeding 710 kgs/m³, and they shall be covered with PP

foil of Renolit, Germany brand/make with a thickness of 120 microns. The adhesive used for affixing the panels

must be PUR (polyurethane) hotmelt glue, and the design of the panels will be as per the specifications

provided by the architect. The dimensions of the panels are 17-18mm in thickness, 130.5mm in width, and

2745mm in length.The scope of work includes providing and fixing these MDF wall panels onto a framework

constructed either from MDF or plywood. The framework should have a thickness of 50 mm and a width

ranging from 8mm to 12mm. The installation of the panels can be executed through either the nail-down

method or the pasting method, with the use of a high bonding adhesive suitable for MDF and plywood, NRC

0.65 upto 1 NRC . The finishing of the MDF wall panels should adhere to the approved architectural drawings

and the directions provided by the Engineer-in-Charge (EIC).

11 MR-33 Supply of 12mm PET panels which shall be processed with a UniVic VMT technology for surface customised sqm 15.00 6500.00 97500.00

colour options as per the designers requirement, the panel shall be made from-

-100% polyester fiber, with up to 70% recycled and 30% binding fiber panel shall be strong and resistant to

wear and tear, maintaining the structure and appearance over time. panel shall be Non-toxic, non-irritant, and

fire-resistant complying with safety standards for interior applications. Nominal thinkness- 12mm (± 0.5mm)

Density- 166.7 kg/m3 2000 GSM .0.35 with direct fix , 0.85 with 25 mm gap with infill , 0.95 with 50 mm gap

with infill . Fire Rating : The Panels shall confirm to Class 1 Fire Ratings tested as per BS 476 Part 6 (Fire

Propagation) & 7 (Surface spread of flame) as also ASTM D 2859 (Ignition charateristics) Smoldering ciggarate

ignition source-fire test Confirming -BS 5852 : Part 1. Recycled Post-Consumer Polyester- Complient to-GRS .

Thermal Properties- complient to- ASTM C 518

12 MR-34 Providing & fixing 6 mm thick GRIHA rated lacquered glass with flat polished edge fixed to 5.5 mm thick plain Sqm 13.20 4335.72 57231.50

MDF board backing with neutral silicone and/or double-sided adhesive pads etc. ,including polishing/MTG all

complete as per the drawing & directions of engineer-in-charge. 6.0 mm thick

13 MR-35 Providing & Fixing PVC wall covering 1 to 2mm thick as per design and finish having fiber backing for sound Sqm 91.48 2787.25 254966.00

insulation. Covering to be pasted on Mdf base with adhesive as approved by manufacture. Material should be

fire resistance as per ISO 105-B02 > grade 8 All complete as per engineer in charge

14 MR-36 Providing & fixing commercial grade wall paper of approved shade to MDF/Gypsum board/POP Punning base sqm 16.50 1858.16 30659.64

backing which have 100% washable, scratch resistance, peel proof, and fire retardant properties, including

preparation on the punned surface for receiving the wall paper, adhesive as per the manufacturer

specification, all complete as per the drawing & directions of engineer-in-charge( Base backing to be paid

Digitally signed by AMITNSL

15 Providing & fixing FRP sqm 7.20 64560.00 464832.00

1. Structure & Material:

• Core made from ISO-grade FRP (Isophthalic Resin-based Fiber Reinforced Polymer) with a thickness of 4–6

mm, ensuring weather resistance, durability, and lightweight strength.

• Integrated MS pipe at the top edge for reinforcement — available in 0.75” or 1” size depending on load

• Collar section size: 9’ x 13’

2. Support Design:

• Fixed triangular FRP reinforcement ensures maximum stability and load distribution.

3. Surface Finish:

• Final product is smooth-surfaced with light texture, suitable for paint or direct use.

• Color can be customized as per project needs (e.g. matte white, textured beige, or RAL codes).

4. Installation:

• No extra mechanical fitting required — simply place and fix.

• Designed for quick on-site installation without special tools or expertise.

5. Technical Highlights:

• UV resistant, waterproof, termite-proof, and corrosion-free

• Does not warp, crack, or deform under pressure or heat

• Ideal for interior partitions, facade supports, or decorative edges

• Lightweight for transport, yet structurally sound for long-term applications

16 MR-37 Providing & Fixing of Sleek Partition System SG 75 ie. Single glazed modular system consist of Aluminium sqm 40.32 5806.76 234128.56

section of 20*75*2 mm thick. All sections duly anodised up to 15-20 microns with 6003 grade and required

accessories ie glass to glass aluminium I sections, T section & 90 degree sections & Glass packing to adjust the

floor level. Ceiling profile & Floor profile and wall profile are 20 mm visible face and 75 mm wide. Profiles will

come in three sides alongwith ( Top, Bottom and Verticle on Wall side) Forth Verticle will come where No

adjusant door comes. Partition will have 10mm toughen glass & insertion of silicon/Thermoplastic gasket to

adhere the glass firm & airtight.

17 MR-38 Providing and fixing electroplating SS PROFILE of colour and design as per engineer in charge Metre 125.00 708.04 88505.00

18 9.40.1.2 Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming Metre 211.20 271.75 57394.00 55844.362

coat on unexposed surface etc. complete : 2nd class teak wood:50 x 20 mm

19 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface sqm 435.00 262.70 114275.00 111189.575

even and smooth complete.

20 MR-39 Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers sqm 435.00 484.20 210627.00 204940.071

specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special

primer applied @ 0.75 ltr /10 sqm

21 MR-40 Providing and applying two or more coats of Textured Paint/ Surface Coating of approved make and shade sqm 435.00 807.00 351045.00 341566.785

over walls etc. after preparing the surface with a coat of primer and 6 mm thick plaster of paris punning to give

a smooth and even surface etc. complete. base price 85 per sqft

22 13.116 Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade sqm 57.00 3049.00 173793.00 169100.589

texture with following process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is

allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess

sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special

grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6

hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs.

Digitally signed by AMITNSL

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine

thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet

rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with

compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required

proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap

23 MR-41 Providing and fixing Roller Blind system consisting of a coated aluminium tube of 38 mm diameter of sqm 71.28 2787.25 198675.18

approved colour with provision of fabric clamping. The Fabric is rolled up and down through a chain drive

system with built in drive gear and an over run brake system. The side brackets are universal type suitable both

for wall and ceiling mounting. The bottom end of the fabric is rolled over an oval shape aluminium tube with

provision to lock the fabric.The rate shall be inclusive of all the necessary material,required hardware, labour,

transportation, necessary for the complete execution of the item . basic price 180 Sqft

24 MR-42 Providing & Fixing 3M & equivalent Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect Sqm 13.86 1316.20 18242.53

film to reproduce Sand-blasting effect on glass with customized designs, thickness of 2 mil (0.05mm) without

adhesive & 3M & equivalentil (0.8)with adhesive having minimum tensile strength of 3.5 pound/inch at 73

F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass

Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors) must be endorsed by

Electronically/computer plotter cut. Applied on glass and other rigid, clear substrates. (partitions, doors,

windows etc.) Available in 5 colours

Total Carried Over to Abstract for Sub Head: 6.00 Wall Finshes Work : 1292642.61 2706576.74

SH 7 REPAIRS TO BUILDING 0

1 14.75 Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the Sqm 20.6 670.95 13822 13448.806 0

patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based

polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of

Engineer-In-Charge.

Total Carried Over to Abstract for Sub Head: 7.00 Repairs To Building : 13448.81 0

SH 8 METAL WORK

1 10.25.2 Steel work welded in built up sections/ framed work, including cutting,vhoisting, fixing in position and applying Kg 130.00 172.6 22438 21832.174

a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar,

ladder, railings, brackets, gates and similar works

2 10.16.3 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, Kg 120 194.4 23328 22698.144

hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted

with special shaped washers etc. complete. Electric resistance or induction butt welded tubes

Total Carried Over to Abstract for Sub Head: 8.00 Metal Work : 44530.32 0

SH 9 OTHER WORKS

SHOP DRAWINGS: Preparation of complete set of shop drawings including finishing, MEP services, details, LS 1 200,000.00 200,000.00

design calcualtions etc. and for prepration of as built drawing any other details as and when desired by Engineer

Incharge/ client. A qualified professsional for the purpose shall be appointed after due appproval from Engineer-In-

CUSTOMISED STORAGE UNIT: Supply and fixing of full height storage units (upto 450mm depth) made out of Sqmt 12.5 11265 140,812.50

18mm plywood finished with approved .8mm laminate on the inside and outside. Including

Glss/Handles/nuts/bolts/ all hardware etc. Hardware used of Hettich make.Compleate as per the direction of

Engineer in charge

Total Carried Over to Abstract for Sub Head: 9.00 Other Works : 340,812.50

Digitally signed by AMITNSL

S.No. Room Specification Unit Qty Unit Price MR Amount

Providing and Placing Main TAble of Size 3000x2550x740.MAIN WORKTOP Size 3000x1050x740, ERU Each 1 225,500.00 225,500.00

1500x600x610mm- Main worktop - Made of 43mm Thick (±1) combination of MDF and particle board with

laminate. All edges are edge banded with matching 1mm thick laminate lipping.LEATHER PAD:Made of 18mm

Thick (±1) MDF with Leatherette wrapped around top surface. This leather pad is fixed to main top panel.DRAWER

UNIT:Top panel and drawer unit modesty panel is made of 43mm Thick (±1) combination ofMDF and particle board

with top veneer face coated with clear lacquer. All thickness edges are edge banded with matching

lipping.Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Bottom panel of drawer is 9mm

thick particle board with leatherette on top surface.Drawer unit is provided with soft closing channels for smooth

opening and closing.Drawer unit is secured with side central lock.OPEN STORAGE UNIT:Top panel and open

storage unit modesty panel is made of 43mm Thick (±1) combination of MDF and particle board with top veneer

1 DG main table face coated with clear lacquer. All thickness edges are edge banded with matching lipping.Remaining construction is

of 18mm Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge

banded with matching 2 mm thick PVC lipping.MODESTY:Made of 18mm Thick Pre-laminated twin board (PLT) of

E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC

lipping. Modesty is fitted with aluminum trims.UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board

(PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick

PVC lipping. Door is fixed with soft closing hinges and handle is provided for ease of opening.Also lock is provided

on side panel for security.ACCESS FLAP WITH POWER BOX:Soft closing access flap with power box contains 3

Universal Sockets, 2 USB power points, 1 HDMI connection, 1 inbuilt misc. cable grommet and CAT 3 and CAT

Providing and placing Back unit of size 3000 mm(L)x470mm(D)x2325mm(H).CONSTRUCTION AND MATERIAL: Made from Each 1 138,961.00 138,961.00

combination of Top panel(0.5mm CRCA), side panel(0.5mm CRCA), Bottom panel(0.5mm CRCA for 600W and 0.8mm CRCA

for 1200W), Back panel(0.5mm CRCA), Top Bottom stiffener(1.2mm CRCA) and End Cover(0.5mm CRCA). Shelves are 12

bend panel made of 0.7mm Thick CRCA (D Grade, IS-513). 4 nos of shelves for 1950H and 5 nos of shelves for 2325H back

unit. Storage body is powder coated with Epoxy Polyester to the thickness of 50 microns (+/-10 micron). Finish VENEER

2 Backunit DOOR: Made of 12mm Thick (±1) MDF with 3.5mm veneer both side and face coated with clear lacquer. All edges are edge

banded with matching 1mm thick veneer lipping. Door is provided with soft closing hinge. Handle is also provided for ease

of opening. Storage is secured with 3 way cam lock.GLASS DOOR: Made from the combination of aluminium alloy (63400)

extrusion and 4mm clear toughened glass. Aluminium extrusion of glass doors are powder coated with Epoxy Polyester to

the thickness of 50 microns (+/-10 micron). Handle is provided for ease of opening. RH Glass Door is provided with 3 way

cam lock for security.

Providing and placing High Back chair.SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled Each 1 165,000.00 165,000.00

poly-amide. Upholstered seat (Pure Leather ) sub-assembly consists of moulded High Resilience (HR) Polyurethane foam of

Density 45±2 kg/m³, and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE: 45.5cm. (D) x 52.4cm. (W)

2. BACK ASSEMBLY: The Cushioned back is made of PU Foam with Polypropylene Injection molded Plastic Inner. *HIGH

BACK SIZE: 50.5 cm. (W) x 76.7 cm. (D) Height adjustment sub assembly is inserted in the Aluminum Die Cast Arm body & all

other adjustment are provided in adjustable arm top sub assembly. · Up-Down adjustment has 8 position (10.5±0.5cm

range) · Arm top swivel adjustment- 2 position, 12°±2° swivel inside · Arm top width adjustment - Any position (2.0±0.5cm

range each arm top) · Arm top To - Fro Adjustment- any position (4.0±0.5cm range) · Armrest top is made up of high density

PU molded over glass filled Poly-amide inner. MECHANISM: The adjustable tilting mechanism is designed with the following

features: · 360° revolving type. · Forward tilt of sesat and back. · Upright tilt lock. · Tilt tension adjustment can be operated

in seating position. · 3-position Tilt limiter. . SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat

and integrated with the mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position.

Seat depth adjustment range is of 5.0±0.5 cm. 6. ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish die

cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position. It can be

adjusted in the range of 7.5±0.5 cm.PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4 pneumatic height

adjustment has an adjustment stroke of 13.0±0.3 cm. PEDESTAL: The pedestal is made of die-cast aluminium with buffing

finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia.TWIN WHEEL CASTOR: 5 Nos.

twin wheel soft castors are injection moulded in Poly-amide with PU lining, having 6.5±0.1cm wheel Diameter and

assembled to pedesta

SEAT ASSEMBLY: The Cushioned seat inner is made of injection moulded glass filled poly-amide. Each 4 84,460.00 337,840.00

Upholstered seat sub-assembly consists of moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m³, and

hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. 2. BACK

ASSEMBLY: The Cushioned back is made of PU Foam with Polypropylene Injection molded Plastic Inner.*MID BACK SIZE:

3. ARMRESTS: The armrest having four range of adjustment.Height adjustment sub assembly is inserted in the Aluminum

Die Cast Arm body & all other adjustment are provided in adjustable arm top sub assembly.Up-Down adjustment has 8

position (10.5+0.5cm range).Arm top swivel adjustment- 2 position, 12°+2° swivel inside.Arm top width adjustment - Any

position (2.0÷0.5cm range each arm top) Arm top To - Fro Adjustment- any position (4.0$0.5cm range).Armrest top is made

up of high density PU molded over glass filled Poly-amide inner.

POSTURE PERFECT MECHANISM: The adjustable tilting mechanism is designed with the following features:360° revolving

type. Forward tilt of sesat and back. Upright tilt lock.Tilt tension adjustment can be operated in seating position.3-position

4 Visitor Chair

Tilt limiter. SEAT DEPTH ADJUSTMENT: Seat

depth adjustment is housed below the seat and integrated with the mechanism with help of Polypropene Seat cover. Seat

Depth can be adjusted in sitting position. Seat depth adjustment range is of 5.0$0.5 cm.

ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish die cast aluminum Spine with an Up-Down

mechanism assembly. Back Height can be adjusted in sitting position. It can be adjusted in the range of 7.5+0.5 cm.

PNEUMATIC HEIGHT ADJUSTMENT: The heavy duty class 4 pneumatic height adjustment has an adjustment stroke of

13.0$0.3 cm. PEDESTAL: The

pedestal is made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal is 67.0 ÷

0.5cm pitch-center dia. TWIN WHEEL CASTOR: 5 Nos. twin

wheel soft castors are injection moulded in Poly-amide with PU lining, having 6.50.1cm wheel Diameter and assembled to

Two Seater Sofa 2 SEATER SOFA- Muuto InSitu 2 Seater Sofa Country of Production: Denmark Supplying and placing in Each 2 61,170.00 122,340.00

position 2 Seater Sofa of size 1420mm W x 1070 mm D x Seat Depth 740mm with Seat Height 380mm. Product Material

Frame in powder-coated steel. Modules in an FSC™-certified (FSC-C028824) wood construction with foam and wadding.

Fully upholstered with approved fabric. Powder Coated Steel Steel is an alloy of iron with carbon. Powder coated steel has a

subtle, textured expression and elegant feel while adding durability to the design and making it more resistant to corrosion.

5 Powder coated steel is also highly chip resistant.The inside of the In Situ sofa features a foam core with a pillowcase filled

with fiber balls. All upholstered products contain flame retardant foam in order to fulfill the stringent flammability standards

under the UK Furniture and Furnishings Fire Safety Regulations. The flame retardant used in the foam is melamine, CAS

number: 108-78 1. Warranty: 12-year limited warranty, 5-year guarantee to the fabrics and foam Eco-Labels & Certificates

Forest Stewardship Council™ (FSC-C028824), Bifma X 7.1, CDPH 01350 Strength, Durability & Stability Certificates: BIFMA

X5.4 — Lounge & Public Seating,

Two Seater Sofa 1 SEATER SOFA- Muuto InSitu 2 Seater Sofa Country of Production: Denmark Supplying and placing in Each 2 41,975.00 83,950.00

position 2 Seater Sofa of size 1420mm W x 1070 mm D x Seat Depth 740mm with Seat Height 380mm. Product Material

Frame in powder-coated steel. Modules in an FSC™-certified (FSC-C028824) wood construction with foam and wadding.

Fully upholstered with approved fabric. Powder Coated Steel Steel is an alloy of iron with carbon. Powder coated steel has a

subtle, textured expression and elegant feel while adding durability to the design and making it more resistant to corrosion.

6 Powder coated steel is also highly chip resistant.The inside of the In Situ sofa features a foam core with a pillowcase filled

with fiber balls. All upholstered products contain flame retardant foam in order to fulfill the stringent flammability standards

under the UK Furniture and Furnishings Fire Safety Regulations. The flame retardant used in the foam is melamine, CAS

number: 108-78 1. Warranty: 12-year limited warranty, 5-year guarantee to the fabrics and foam Eco-Labels & Certificates

Forest Stewardship Council™ (FSC-C028824), Bifma X 7.1, CDPH 01350 Strength, Durability & Stability Certificates: BIFMA

X5.4 — Lounge & Public Seating,

Overall size of 1200mm(L)x594mm(D)x411mm(H).Ultra-modern combination of wood and glass, specifically shaped and Each 2 14,230.00 28,460.00

engineered to give it stability. Now, your drinks won’t spill as easily in case of accidental tugs and yanks.• The Wenge finish

6 Side table of the coffee table is done with utmost care, making it a posh addition to your space.• Has multiple compartments to store

books, magazines, or place decor items. A hidden compartment within can be used to store utility bills and keys.

Digitally signed by AMIT

Overall size of 600mm(L)x600mm(D)x450mm(H)Designed for the modern minimalist with a need for handy, Each 2 10,327.00 20,654.00

compartmentalized storage.• Tabletop of durable, toughened glass with a digitally back-printed Skyline pattern creates a

7 Center table sleek, modern look.• A strong, knockdown construction built for longevity.

B P.S. ROOM -

Supplying of Recta workstation of size 1500X 600x 750 with KBPT , Pedestal , CPU Trolley .Providing DESK based modular Each 2 47,661.00 95,322.00

workstation with worktop thickness 25mm System ht - 750 mm .Understructure - The slanted legs with perforated metal

modesty in between are connected to the understructure with the help of PDC Connectors to provide a stable and sturdy

base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA. Wire Management : Metal powder coated

power box with wire raiser+D56 is given to pull wires from the floor junction box upto the power box fixed under neath the

worktop. Aluminium access flaps on worktop above power box cut out for accessing switches.Worktop mounted metal

modesty made from 0.8 mm thk CRCA (IS: 513) is provided.Worksurface - out of 25 mm thk prelam particle board with flat

pvc lipping edge banding of size 1200 mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full ht free standing

central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The product should be GREENPRO, SCS IAQ,

GRIHA, BIFMA certified.

The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane foam Each 2 12,374.00 24,748.00

and upholstered with high stretch knitted polyester fabric. The back size shall be 45.5cm W x 53.0cm H. The HR

polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly

connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just

with a simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat offers impact

cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped spines moulded

in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form the back spine

structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position

Tilt limiter feature which is inbuilt in saet base and the tension is user weight dependent. The adjustable armrests assembly

consists of armrest housing sliding over the armrest structure, both moulded in glass filled Polyamide. The pneumatic height

adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled Polyamide and fitted with 5 nos.

twin wheel castors. The pedestal is 66cm pitch centre diameter and 76cm with castors. The overall dimensions of the chair

shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be (44.5-53.8cm).

C DR. CABIN -

Providingin place of main table with overall size of table 2400 x 2350 x 750mm. The main table shall be of size 2350 x 1150 x Each 3 113,100.00 339,300.00

750mm. The side unit shall be 1200 x 600 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board

confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box

are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board

confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick

MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The

understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with

matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-

laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses

powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti

slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

The Back Unit shall be of dimensions 2350 x 500 x 750mm. It shall be made of 25mm thick MDF – one side pre-laminate Sqm 10.23 12,500.00 127,875.00

board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm

2 backunit thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping.

Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock

Providing and Placing in Position High Back Chair. The cushioned seats shall be made of injection moulded plastic outer and Each 3 44,512.00 133,536.00

inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof Density = 45±2

kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6 cm W x 49.2 cm D. The

back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x

0.16±0.0128 cm, upholstered with pure leather. Back size shall be 47.5 cm W x 77 cm D. The armrest top shall be moulded

from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable type tubular armrest

support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome plated finish. The armrest hieght shall

be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism shall be designed with the following features :

360° revolving type, front-pivot for tilt with feet resting on ground and contionuous lumbar support ensuring more comfort,

Tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving options of variable tilt angle to the

chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black powder coated. Seat depth

adjustment shall be integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm.

Back frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the range of

7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall have an

adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of

twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection

moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5-114cm. Seat height Each 9 38,832.00 349,488.00

shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic outer and inner. Plastic inner shall

be upholstered with pure leather and moulded high resiliance polyurethane foamof Density = 45±2 kg/m³, and hardness

load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned

and shall be made up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm,

upholstered with pure leather. The armrest top shall be moulded from polurethane, and shall be upholstered with pure

leather and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm

thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The

adjustable tilting mechanism shall be designed with the following features : 360° revolving type, front-pivot for tilt with feet

4 Visitor Chair

resting on ground and contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in

seating position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be integrated in the

seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back frame shall be connected to the

up/down mechanism housed in plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back

support to suit individual need. the pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm. The

pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall

be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel

diameter and assembled to pedestal.

Supplying and Placing in place of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x 855H. The seat Each 3 35501.00 106,503.00

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density

32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam

with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with

5 fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be

resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos.

per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a

welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat Each 3 27238.00 81,714.00

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density

32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam

with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with

6 fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be

resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos.

per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a

welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Digitally signed by AMIT

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with Each 3 9169.00 27,507.00

understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions

7 Side table of table shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with Each 3 13800.00 41,400.00

understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions

of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

8 Center table

Providingin place of main table with overall size of table 1800 x 1750 x 750mm. The main table shall be of size 1800 X 750 x Each 4 75,800.00 303,200.00

750mm. The side unit shall be 1000 x 500 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board

confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box

are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board

confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick

MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The

1 Main table understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with

matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-

laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses

powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti

slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

The Back Unit shall be of dimensions 1800 x 500 x 750mm. It shall be made of 25mm thick MDF – one side pre-laminate Each 4 46,800.00 187,200.00

board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm

thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping.

Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock

Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat Each 4 22,517.00 90,068.00

Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with

leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per

IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu

molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm

x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest

support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height

adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving

3 Main chair type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension

adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair,

Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth

adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame

is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the

comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of

10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The

pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in

plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.

Providing and Placing Mid Back Chair with overall size of 76.1 cm W x 76.1 cm D x 96.5 – 114 cm H x 43.1 – 53.1 cm Seat Each 8 22,517.00 180,136.00

Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with

leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per

IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu

molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm

x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest

support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height

adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving

4 visitor chair type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension

adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair,

Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth

adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame

is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the

comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of

10.0±0.3cm. The pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The

pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in

plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.

Supplying and placing in position Table of the following specifications. Table size shall be 1500 Width mm x 750 Depth mm x Each 10 52,717.00 527,170.00

740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and

1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick

plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC

beading. ERU LHS size shall be 1050 Width x 450 Depth x 705 Height. The top shall be 25 mm thick plain particle board

(PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2

mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative

Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading.

The Back Unit shall be of dimensions 1500 x 500 x 750mm. It shall be made of 25mm thick MDF – one side pre-laminate Each 10 36,750.00 367,500.00

board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm

2 Back unit thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping.

Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon & Each 10 18,500.00 185,000.00

upholstered using net fabric with high tenacity yarn. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is

moulded with density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an

up=Down adjustment of 8.5 ± 0.5cm which is provided in armrest structure. Armrest top has an integrated layer of

thermoplastic elastomer. Armrest is made up of plastic injection moulded nylon with textured top. It shall have Front pivot

3 MAIN CHAIR synchro mechanism with following features. 360 degree revolving type, Single point control, front fivot tilt, tilt tension

adjustment, 4 position locking with anti- shock feature, seat/back tilting ration of 1:2. The lumber support consists of

polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The height of lumber pad can be

adjusted through two projecting knobs provided on the rear side of the pad. Lumber pad has an adjustment of 8.0± 0.5 cm

in height. The must be greenguard certified. the work shall be carried out as per guidance and instructions recieved from

Engineer Incharge. This shall come along a headrest from same family.

The seat is made up of 1.2± 0.1cm thk. Hot pressed plywood. The back is made up of injection moulded glass filled nylon & Each 20 12,400.00 248,000.00

upholstered using net fabric with high tenacity yarn. Seat Size:- 47cm(w) × 51.5cm (D). The HR polyurathene foam is

moulded with density =55+/-2 kg/m cube and hardness 16± 2 kgf as per is:7888 for 25% compression. The armrest has an

up=Down adjustment of 8.5 ± 0.5cm which is provided in armrest structure. Armrest top has an integrated layer of

thermoplastic elastomer. Armrest is made up of plastic injection moulded nylon with textured top. It shall have Front pivot

4 synchro mechanism with following features. 360 degree revolving type, Single point control, front fivot tilt, tilt tension

adjustment, 4 position locking with anti- shock feature, seat/back tilting ration of 1:2. The lumber support consists of

polypropylene pad with mouled polyurathene foam & covered with polyester fabric. The height of lumber pad can be

adjusted through two projecting knobs provided on the rear side of the pad. Lumber pad has an adjustment of 8.0± 0.5 cm

in height. The must be greenguard certified. the work shall be carried out as per guidance and instructions recieved from

Engineer Incharge.

Digitally signed by AMIT

Supplying of Recta workstation of size 1500X 1500x 750 with KBPT , Pedestal , CPU Trolley .Providing DESK based Each 8 38,700.00 309,600.00

modular workstation with worktop thickness 25mm System ht - 750 mm .Understructure - The slanted legs with

perforated metal modesty in between are connected to the understructure with the help of PDC Connectors to provide a

stable and sturdy base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA. Wire Management : Metal

powder coated power box with wire raiser+D56 is given to pull wires from the floor junction box upto the power box fixed

under neath the worktop. Aluminium access flaps on worktop above power box cut out for accessing switches.Worktop

mounted metal modesty made from 0.8 mm thk CRCA (IS: 513) is provided.Worksurface - out of 25 mm thk prelam particle

board with flat pvc lipping edge banding of size 1500 mm w x 1500 mm d.Pedestals - Nova pedestal flat metal front, full ht

free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file.

Supplying of Recta workstation of size 1200X 600x 750 with KBPT , Pedestal , CPU Trolley .Providing DESK based modular Each 9 29,717.00 267,453.00

workstation with worktop thickness 25mm System ht - 750 mm .Understructure - The slanted legs with perforated metal

modesty in between are connected to the understructure with the help of PDC Connectors to provide a stable and sturdy

base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA. Wire Management : Metal powder coated

power box with wire raiser+D56 is given to pull wires from the floor junction box upto the power box fixed under neath the

worktop. Aluminium access flaps on worktop above power box cut out for accessing switches.Worktop mounted metal

modesty made from 0.8 mm thk CRCA (IS: 513) is provided.Worksurface - out of 25 mm thk prelam particle board with flat

pvc lipping edge banding of size 1200 mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full ht free standing

central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file.

Supplying of Recta workstation of size 1000X 600x 750 with KBPT , Pedestal , CPU Trolley .Providing DESK based modular Each 4 26,717.00 106,868.00

workstation with worktop thickness 25mm System ht - 750 mm .Understructure - The slanted legs with perforated metal

modesty in between are connected to the understructure with the help of PDC Connectors to provide a stable and sturdy

base for the worktops. Modesty panel shall be of Metal 1.2 mm thick CRCA. Wire Management : Metal powder coated

power box with wire raiser+D56 is given to pull wires from the floor junction box upto the power box fixed under neath the

worktop. Aluminium access flaps on worktop above power box cut out for accessing switches.Worktop mounted metal

modesty made from 0.8 mm thk CRCA (IS: 513) is provided.Worksurface - out of 25 mm thk prelam particle board with flat

pvc lipping edge banding of size 1200 mm w x 600 mm d.Pedestals - Nova pedestal flat metal front, full ht free standing

central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. .The product should be GREENPRO, SCS IAQ,

GRIHA, BIFMA certified.

Providing and Placing mid back Chair .SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressedplywood Each 21 12,800.00 268,800.00

and upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge

to give comfort to popliteal area.The Back is injection moulded in glass filled Polypropylene which is upholstered withMesh

fabric.The back consist of adjustable lumbar support made of injection mouldedPolypropylene having an adjustment of 5.0

±0.1 cm.The chair seat & back size are

*SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)*MESH BACK SIZE 51.0 cm. (W) x 70.0 cm. (H)2. HIGH RESILIENCE (HR)

POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 16±2 kgf as per

IS:7888 for 25% compression.

4 3. ARMRESTS :The adjustable armrest is designed with the following features :· Up-Down adjustment– 6 steps (7.2 ± 0.5cm

range)· Armrest top is mounted on Armrest structure made of glass filled Nylon· Armrest Top is PU moulded over glass filled

4. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism isdesigned with the following features:· 360°

revolving type.· 3 position locking with anti shock mechanism.]· Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT:

The pneumatic height adjustment with anadjustment stroke of 9.5 ± 0.3cm.

PEDESTAL ASSEMBLY : The pedestal is injection moulded in glass-filled Nylon andfitted with 5 nos. twin wheel castors. The

pedestal is 66.1 ±0.5cm. pitch-center dia.(76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are

injection moulded in Black Nylon

D RECEPTION -

Supplying and Placing a Reception table of size 2400 X 1770 X 1080 MM, Made of 25mm Thick Pre-laminated twin board of Each 1 81,900.00 81,900.00

E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access

Flap provided on work surface for wire management. Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate

(8+3 Module cutout provision for Anchor Roma). This is fixed with worktop along the width at Access Flap position Made of

25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with

matching 2 mm thick PVC lipping. Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Made of 18mm Thick Pre-laminated twin

RECEPTION board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping

TABLE Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge

banded with matching 2 mm thick PVC lipping.**Drawer bottom is made of 5.5thk MDF whiteboard Handle is provided for

ease of opening. HDU and Drawer is provided with cam lock for security Wire Riser made of 0.8mm CRCA (IS-513) is

provided for proper wire management. Organizer Plate made of 1.2mm CRCA (IS-513) is provided for magnetic sticky notes.

Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging. Company should be ISO-9001, 14001,

45001,50001, Greenguard, BIFMA and AIOTA certified. Product should be Greenguard (UL) certified. Company and Product

Certificate Must Be Certified from Valid Authorised Laboratories

The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane foam Each 1 12,374.00 12,374.00

and upholstered with high stretch knitted polyester fabric. The back size shall be 45.5cm W x 53.0cm H. The HR

polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly

connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just

with a simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat offers impact

cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped spines moulded

RECEPTION in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form the back spine

CHAIR structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position

Tilt limiter feature which is inbuilt in saet base and the tension is user weight dependent. The adjustable armrests assembly

consists of armrest housing sliding over the armrest structure, both moulded in glass filled Polyamide. The pneumatic height

adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled Polyamide and fitted with 5 nos.

twin wheel castors. The pedestal is 66cm pitch centre diameter and 76cm with castors. The overall dimensions of the chair

shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be (44.5-53.8cm).

Supplying and Placing in place of 2 seater sofa. The overall dimensions of the sofa shall be 1460W x 905D x 855H. The seat Each 2 35501.00 71,002.00

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density

32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam

with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with

3 fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be

resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos.

per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a

welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Supplying and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat Each 1 27238.00 27,238.00

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density

32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam

with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with

4 fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be

resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos.

per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a

welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with Each 2 9169.00 18,338.00

understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions

of table shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.

Digitally signed by AMIT

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with Each 1 13800.00 13,800.00

understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions

of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

6 CENTER TABLE

H CONFERENCE -

Providing and Placing in position Conference table for 18 seater having 8 Nos of 2 Seater Modules of size 1350mm X Each 1 205,813.00 205,813.00

600mm X 740mm , 2 Nos of one seater module . Worktop- Made of 25mm thick MDF-one side pre-laminate board

conforming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top and having chamfered edge.Plastic ABS access

flap is provided for easy access to wires and cables.Modesty consist of 18mm Thick Pre-laminated twin board of E1-P2

grade and approved shadeconforming to IS-12823:1990, Aluminium alloy 63400 - WP profile is used for connecting panels

CONFERENCE together. The product has a knock-down construction.It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade

TABLE and approved shadeconforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy

63400 - WP profile is used for connecting panels together. The product has a knock-down construction.An array of panels

made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated(DFT 40-60 microns) is used for flow of wires and cables.

Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece

injectionmoulded plastic part polymer component is fitted to pull out audio,video cables ontoworktop and connect devices

charger to power socket below worktop.

Providing and Placing in Position High Back Chair. The cushioned seats shall be made of injection moulded plastic outer and Each 1 44,512.00 44,512.00

inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof Density = 45±2

kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6 cm W x 49.2 cm D. The

back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x

0.16±0.0128 cm, upholstered with pure leather. Back size shall be 47.5 cm W x 77 cm D. The armrest top shall be moulded

from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable type tubular armrest

support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome plated finish. The armrest hieght shall

be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism shall be designed with the following features :

360° revolving type, front-pivot for tilt with feet resting on ground and contionuous lumbar support ensuring more comfort,

Tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving options of variable tilt angle to the

chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC aluminium black powder coated. Seat depth

adjustment shall be integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm.

Back frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the range of

7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall have an

adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of

twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection

moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

Providing and Placing in Position Mid Back Chair. The overall dimensions shall be 76.1cm x 76.1cm x 96.5-114cm. Seat height Each 24 31,832.00 763,968.00

shall be 44.5cm - 54.5cm. The cushioned seats shall be made of injection moulded plastic outer and inner. Plastic inner shall

be upholstered with pure leather and moulded high resiliance polyurethane foamof Density = 45±2 kg/m³, and hardness

load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned

and shall be made up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm,

upholstered with pure leather. The armrest top shall be moulded from polurethane, and shall be upholstered with pure

leather and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm

thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The

adjustable tilting mechanism shall be designed with the following features : 360° revolving type, front-pivot for tilt with feet

resting on ground and contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in

seating position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the

mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment shall be integrated in the

seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back frame shall be connected to the

up/down mechanism housed in plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back

support to suit individual need. the pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm. The

pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall

be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel

diameter and assembled to pedestal.

The overall size shall be 1950x(H) x 900(W) x 450(D).Aesthetically appealing completely knock - down contruction.1 main Each 1 24,709.00 24,709.00

unit is of 900mm(W).Legs fitted with screw type leveler. Shelving - It is a 12 bend panel made of 0.7mm thick CRCA (D-

Full Height Grade IS -513). Each shelf has max load of 55kg . Wooden Doors - 2 door ( LH - RH) for 900(w).Made of 18mm thick

Storage prelaminated twin board of E1 -P2 Grade and approved shade confirming to IS- 12823:1990. Soft Closing Hinge. Handle -

Aesthetically appealing handle made of aluminium.lipping - Lipping 2 mm thick on all the edges.Locking - Cam lock with 3

way locking provision.Zinc Alloy die cast housing.

Supplying of side storage unit of officers having dimension 1190WX 450DX 1200H:Overall size of hinge door unit is Each 5 23,105.00 115,525.00

1190(H)x740mm (h)x450 mm (D). Providing and placement of back storages with : CONSTRUCTION & MATERIAL

Construction is a knockdown construction of 25mm thk and 18mm thk Pre-Laminated boards with metal cladding of 1.0 mm

thk C.R.C.A (as per IS:513) from outside. Side metal cladding is coated with Epoxy polyester powder of 50±10 microns

thickness. TOP OPTIONS- The Storage units are provided with 11mm thk bent metal tops made of 1.0 mm thk C.R.C.A (as per

IS:513). The metal tops are coated with Epoxy polyester powder of 50± 10 microns thickness. DOOR & DOOR OPENINGtwo

door opening for all other width of 1050 W.The doors are made of 18mm thk Pre-laminated boards with decorative

laminate on one side and backing laminate on the other side. SHELVING- Height wise adjustable shelf mounting holes

Workstation provided on side panels for easy interchange of shelf height as required. Fixed shelves along with adjustable shelves

2 area storage provided only in case of 4.0 feet height units. No fixed shelves for 2.5 feet height storage units. Uniformly distributed load

(1200X450) capacity for each shelf is 40kg maximum. SKIRTING OPTION- The skirting units are provided with 150mm high skirting made

of 1.0 mm thick C.R.C.A(as per IS:513) and is coated with Epoxy polyester powder of 50+-10 micros thickness. LEVELER-

Screw type adjustable leverer with plastic base provides vertical adjustment for floor unevenness and levelling of

units.BACK PANELS Back panels are made of 18mm thick pre-laminated boards with options of decorative as well as fabric

finishes. 2.5 height units consists of single back panel whereas 4.0 height and 4.5 height units consist of split back top panel

and split back bottom panels separated by an Aluminium extrusion. LOCKING MECHANISM- 3-way nickel plated wooden

furniture lock is provided for effective and positive locking of doors. HANDLE- Aesthetically appealing recessed handles of

Aluminium extrusion are provided for easy opening and closing.The OEM should be ISO 9001:2015,ISO 14001:2015 & ISO

18001:2007 certified..

Storwel plain shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have the Each 1 24,488.00 24,488.00

shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other

components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per

IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have

a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also

have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of

50 microns (+/- 10). Plenty of colour options and shelving options shall be available.

Digitally signed by AMIT

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF MINISTRY OF MINES, 9TH FLOOR, NEW DELHI

ABSTRACT OF COST

NAME OF WORK-PLUMBING WORK

DSR-2023/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

Providing and fixing white vitreous china extended wall mounting Each 1 28950.00 28950.00

water closet Wall hung toilet with electronic cleansing in Seat White

of approved shape including providing & fixing Pneumaticcisten tank

1.0 MR-1 3/6L with full frame with dual flush fitting, ,including seat cover, and

cistern fittings, flush plate with brush gold finish , hand faucet, nuts,

bolts and gasket etc complete. all fitting in crome finish

Providing and fixing Toilet paper holder POLISHED CROME : C.P. Each 1 6800.00 6800.00

Providing and fixing under counter wash basin including painting of Each 1 9949.80 9949.80

fittings and brackets, cutting and making good the walls wherever

required. White Vitreous China Wash basin size approx 550x400 mm

including , nuts, bolts and gasket and bottle trap etc complete. Alll

Fitting in brush gold finish

Providing and fixing under counter wash basin including painting of Each 1 8132.11 8132.11

fittings and brackets, cutting and making good the walls wherever

required. White Vitreous China Wash basin size approx 550x400 mm

including , nuts, bolts and gasket and bottle trap etc complete. All

Fitting in crome finish

Providing and fixing inset lighting mirror of superior glass (of Each 1 20728.75 20728.75

approved quality) complete with ground fixed to wooden cleats with

5.0 MR-5 C.P. brass screws and washers complete.

Providing and fixing wall mounted basin mixture including inner Each 1 8132.11 8132.11

fitting and all fitting as required Alll Fitting in CROME finish

Providing and fixing C.P. brass angle valve for basin mixer and geyser Each 1 574.30 574.30

points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass Each 1 97.75 97.75

8.0 18.21.2.1 unions : 45 cm length , 15 mm nominal bore

Providing and fixing Liquid soap Dispensor in polished crome in brass , Each 1 4464.53 4464.53

9.0 MR-7 lead free refillable ALL fitting in chrome finish

Providing and fixing towel ring round shape crome finished Each 1 2594.06 2594.06

Providing and fixing wall mounted diverter with inner and upper part Each 1 8945.32 8945.32

in brass, finshed in crome polish including all requird accessories to

complete installation

Providing and fixing C.P. brass Spout of approved quality conforming Each 1 34809.00 34809.00

13.0 MR-11 Providing and fixing Coat Hook. Each 1 1374.02 1374.02

Supply,Installation, testing and commissioning of Water Heater Each 1 13384.00 13384.00

complete with heavy gauge hot and cold water flexible pipe

14.0 MR-12 connections, Nano polymer coated tank, 8 bar pressure ,of approved

make complete with all necessary material as directed by Engineer -

in - Charge. 25-Litre Storage capacity

Providing and fixing CP Brass 32 mm size Bottle Trap of approved Each 1 1034.80 1034.80

15.0 17.22A quality & make and as per the direction of Engineer-in-charge.

PLUMBING WORK NSLby AMIT

Digitally signed

ABSTRACT OF COST

NAME OF WORK-PLUMBING WORK

DSR-2023/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

Supply installation, testing and commissioning of water cooler with Each 1 89607.43 89607.43

Inbuilt RO purification .Cooling capacity shall be 60 liter & 80 liter

shall be storage capacity.Its should have 7 stages purification

process,fully automatic,rectangular tank with Forced fin and tube

16.0 MR-13 condenser,Non-corrosive SS-304 outer body,Food-grade SS-304

stainless steel inner tank (18/8 or 18/10),PUF insulation,Reciprocating

compressor with R22 Refrigerant.Water outlet temp is aprrox 17 deg

c ,Operating power supply 230 + 10% V AC,50 Hz,1 PH,No of Cold

water Faucet-2.

Providing and fixing ABS Auto aerosol Dispenser, fixed to wooden

17.0 MR-14 cleats with C.P brass screws, complete including cutting and making

good the walls wherever required.

UTEC : UT-630 / Euronics Nos 6 2212.10 13272.60

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at

1.00 m spacing. This includes jointing of pipes & fittings with one step

1 18.8 CPVC solvent cement and the cost of cutting chases and making good

the same including testing of joints complete as per direction of

Engineer in Charge.

Concealed work, including cutting chases and making good the walls

a) 18.8.1 15 mm nominal dia Pipes Mtr. 20 441.15 8823.00

b) 18.8.2 20 mm nominal dia Pipes Mtr. 20 513.75 10275.00

c) 18.8.3 25 mm nominal dia Pipes Mtr. 10 626.05 6260.50

d) 18.8.4 32 mm nominal dia Pipes Mtr. 18 712.75 12829.50

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, including fixing the pipe with

2 18.7 clamps at 1.00 m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and testing of joints complete as

per direction of Engineer in Charge.

Internal work - Exposed on wall

a) 18.7.1 15 mm nominal dia Pipes Mtr. 2 255.90 511.80

b) 18.7.2 20 mm nominal dia Pipes Mtr. 10 325.10 3251.00

c) 18.7.3 25 mm nominal dia Pipes Mtr. 10 408.55 4085.50

d) 18.7.4 32 mm nominal dia Pipes Mtr. 5 500.95 2504.75

e) 18.7.5 40 mm nominal dia Pipes Mtr. 15 674.35 10115.25

f) 18.7.6 50 mm nominal dia Pipes Mtr. 30 927.00 27810.00

Providing and fixing low noise insulated Polyproplene piping system

as per DIN EN 12056 and DIN1986-100 with 3 layer pipe made of

External layer -PP, middle layer-Mineral reinforced PP, Internal layer-

PP. push-fit type, food safe, having high impact and stiffness, offering

sound levels of not more than 10 dBA as per DIN 4109 at a flow rate

of 2 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and

tightness as per EN 1277/B and C and DIN 19560, density of pipe = 1.9

3.00 MR-1 g/cm3, elongation break 50% and tensile strength 20

N/mm2,Coefficient of linear expansion 0.09 mm/mK with all

necessary fittings fitted with factory fitted lip ring including cutting

and making good the walls, floors, R.C.C. work etc or also incluiding

painting with ordinary cement based paint for external installation.

(including MS structural support & U clamps as required)

PLUMBING WORK NSLby AMIT

Digitally signed

ABSTRACT OF COST

NAME OF WORK-PLUMBING WORK

DSR-2023/ Description of Item UNIT TOTAL RATE DSR AMOUNT MR AMOUNT

a) 110 OD mm dia Pipes Metre 50 1811.00 0.00 90550.00

b) 75 OD mm dia Pipes Metre 80 1166.00 0.00 93280.00

TOTAL FOR DRAINAGE 86466.00 183830.00

GRAND TOTAL (A+B) 86,466.00 183,830.00

GRAND TOTAL (A+B) 86,466.00 183,830.00

Grand Total after RA Correction factoron DSR items 84,131.42 183,830.00

Grand Total after RA Correction factoron DSR items 84,131.42 183,830.00

PLUMBING WORK NSLby AMIT

Digitally signed

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF MINISTRY OF MINES, 9TH FLOOR, NEW DELHI

Name Of Work -Office Block Internal Electrification Work

Rate as per D.S.R. 2025 MARKET BASED

Sr.No. Particulars Sch.No. Qty Unit Rate as per DSR DSR Amount MR Rate MR Amount

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper conductor

single core cable in surface / recessed medium class PVC

1 conduit, with modular switch, modular plate, suitable GI box 1.10.3 198 Nos. 1,704.00 337,392.00 -

and earthing the point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC

insulated copper conductor single core cable in surface/

recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper

conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the

3 following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ 1.14 - -

recessed medium class PVC conduit as required.

Supplying and drawing following pair 0.5 mm dia FRLS PVC

insulated annealed copper conductor, unarmored telephone

cable in the existing surface/ recessed steel/ PVC conduit as

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

5 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the 1.19 120 Meter 54.00 6,480.00 -

existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of recessed

conduit as required.

Supplying and fixing following modular switch/ socket on the

7 existing modular plate & switch box including connections but 1.24 - -

excluding modular plate etc. as required.

C 3 pin 5/6 A socket outlet 1.24.4 12 Each 136.00 1,632.00

d 6 pin 15/16 A socket outlet 1.24.5 10 Each 219.00 2,190.00

e Telephone socket outlet 1.24.6 16 Each 168.00 2,688.00 -

b TV socket outlet 1.24.7 3 Each 168.00 504.00 -

c RJ45 socket cat 6 with shutter RA-1 20 Each - 421.58 8,431.56

Digitally signed by AMIT

Supplying and fixing two module stepped type electronic fan

8 regulator on the existing modular plate switch box including 1.25 19 Each 402.00 7,638.00 -

connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box alongwith

9 modular base & cover plate for modular switches in recess etc. 1.27 - -

Supplying and fixing suitable size GI box with modular plate and cover in front on surface

10 or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A 1.31 38 Each 545.00 20,710.00 -

modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface

11 or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 1.32 4 Each 659.00 2,636.00 -

15/16 A modular switch, connections etc. as required.

Installation ,Testing, Commissioning of wall bracket /ceiling

12 fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, 1.35 179 Each 151.00 27,029.00 -

complete with all accessories including connections etc. as required.

Supplying and fixing stiff pendent with 300 mm long, 20 mm dia X 1.6 mm thick steel

conduit, aluminium cast back plate and brass holder complete, including wiring the down

rod with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and painting

etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase,

230 V, complete as required.

Supplying, drawing, Installation, Testing and commissioning of CAT6 UTP LSZH

23AWG Twisted Pair Cable in existing conduit/ on surface, Category 6 Unshielded

Twisted Pair, 4 pair should be complied as per UL/ETL verification program for

15 compliance with ANSI/TIA-568.2-D standard. Outer diameter should be in the 39.17 -

range of 6.1mm nominal with Operating Temperature Range : -5° to +60°C,

Bending Radius : < 4 X Cable Diameter at –5°C ± 1°C and Pulling Force : 11.5Kg

etc. complete as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell

point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper

16 conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.55 -

1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface

or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2

nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non

residential buildings).

Digitally signed by AMIT

Supplying & fixing suitable size GI box wih modular plate and

cover in front on surface or in recess including providing and

fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including

connections, painting etc. as required.

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit

breaker suitable for inductive load of following poles in the existing MCB DB complete

connections, testing and commissioning etc. as required.

b Double pole 2.10.3 1 Each 696.00 696.00 -

c Three Phase & Neutral 2.10.5 1 Each 1,301.00 1,301.00 -

Supplying and fixing following rating, double pole, (single phase

and neutral), 240 V, residual current circuit breaker (RCCB),

21 having a sensitivity current 30 mA in the existing MCB DB 2.14 -

complete with connections, testing and commissioning etc. as

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts,

residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing

MCB DB complete with connections, testing and commissioning etc. as required.

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways

along with required suitable number of GI couplers for joining raceways and fixing

GI brackets and all accessories complete in all respect as per the directions of

engineer in charge

(a) 300mmx38mm(GI) - 3 compartment 30 meter 3,603.00 108,090.00

(b) 225mmx38mm(GI) - 3 compartment 25 meter 2,960.00 74,000.00

Supply, Installation, Testing and Commisioning of Junction boxes for direct access

to cables at the intersection of raceways supplied completely with base and cover

MR-2 plates, height adjustable junction box 65- 90 mm including all accessories ss plate MR

of 3mm thick complete in all respect as per the directions of engineer in charge

Digitally signed by AMIT

Supplying and installation following size of perforated painted with powder coating M.S.

cable trays bends with perforation not more than 17.5%, joined with connectors,

23 suspended from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size 4.2

MS/GI angle, bolts & nuts, painting suspenders, fastener etc as required.

a 100 mm width X 50 mm depth X 1.6 mm thickness 4.2.1 10 Meter 948 9,480.00

b 150 mm width X 50 mm depth X 1.6 mm thickness 4.2.2 12 Meter 1105 13,260.00

c 300 mm width X 50 mm depth X 1.6 mm thickness 4.2.4 5 Meter 1544 7,720.00

d 600 mm width X 50 mm depth X 1.6 mm thickness 4.2.7 4 Meter 3009 12,036.00

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and

providing masonry enclosure with cover plate having locking arrangement and watering

pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories,

and providing masonry enclosure with cover plate having locking arrangement and

watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth

electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as

required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring

washer spaced at 50mm)

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip

earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as

required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring

washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for

connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing

29 along with existing surface/ recessed conduit/ submain wiring/ cable as required 5.18 30 Meter 50 1,500.00 -

Digitally signed by AMIT

LED Down lighter (SMD Type) (System lumen efficacy >135 lm/Watt)

Supplying, installation, Testing & Commissioning of LED Recessed /

surface Down lighter (Round /square/Rectangular) SMD type of following body material

with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per

the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq

50/60 hz, Operating temp range - 15 deg to 40 deg centigrade, internal surge protection

of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR

(Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver

& electrical circuitry), life time of minimum 50000 Burning Hours with , 70% of initial

Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT

3000°K / 4000°K / 5700°K / 6000°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation

30 Color Matching) <3, Maximum power consumption should not more than the specified 8.1

rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.).

Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM

must have its own in house NABL lab setup for all testing facilities for LED fixtures.

complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper

conductor single core cable and earthing etc. as required with Minimum 5 year OEM

warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from

NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size

and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminum housing such that LED junction temperature shall

not rise above 90°C).

Powder coated die cast / Extruded aluminum Body including trim.

LED Down lighter (COB Type) (System lumen efficacy ≥105 < 120 lm/Watt ).

Supplying, installation, Testing & Commissioning of LED Recessed/ surface Down

lighter (Round/ square/ Rectangular) COB Type of following body material and

construction as per IS : 10322 with driver as per the requirement with Driver

efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz,

Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with

Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR

(Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time

(LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of

initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K / 6500°K (As

per ANSI Bin), SDCM (Standard Deviation Color Matching)

Digitally signed by AMIT

LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt) Supplying,

installation, Testing & Commissioning of Panel light 2x2 ft., of following body

material and construction as per IS : 10322 with driver as per the requirement

with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60

hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with

Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR

(Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time

(LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70%

of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K /6500°K

(As per ANSI Bin), SDCM(Standard Deviation Colour Matching) required with

Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output .

LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall

be submitted. Shape size and CCT shall be as approved by Engineer-inCharge as

per requirement. (Thermal management: heat sink of aluminium housing such

that LED junction temperature shall not rise above 90°C) Powder coated die cast

/Extruded aluminium Body (Thickness > 1.20 mm)

SITC of 12W Extruded aluminium batten available in 2ft run length with multiple lumen

packages and suitable for surface, wall & conduit ounting (with accessories). similar to

Philips Type HSN Code MRP (INR) BN 021 LED12S 6500 PSU GR or equivalent.

Supply and fixing of water tight oblong 10 Watt LED bulkhead luminaire having pressure

diecast housing with driver set confirming to IP 65 and above Protection, IK08, High purity

/ transmisivity UV stablized Non yellowish diffuser/ Reflector for uniform light

34 distribution, ditachable driver set, suitable for 24hrs continuous operation complete in all MR 1 Each 2,006.00 2,006.00

1200 system lumen, >120lm/W, PF>0.95, CRI>70, >300V, over voltage protection, 4KV

internal surge protection with 5 year warrenty. CAT-AAA

Supply, Installation, Testing and Commissioning of non-dimmable 35mm wide Sleek

Suspended 30W LED linear light(1200mm) Linear ultra modular fixture made up of

extruded aluminium housing and multi LED anti glare system having system lumen

>=3300 with luminaire efficacy 110LPW , CRI >80, UGR<19 CCT 4000K. The luminaire

rated life (L70) 50000 hours with inbuilt protection against short circuit,Miswiring,over

voltage and surge protection upto 3 KV PF.0.95 and THD<10% (Driver complaince IEC

61547,IEC 61347-2-13)including making suitable arrangement for fixing including

connection with 3 x 1.5 sq.mm. PVC insulated FRLS PVC sheathed copper conductor etc as

Digitally signed by AMIT

Supply, Installation, Testing and Commissioning of non-dimmable Suspended 30W LED

linear light(1200mm) Linear wih PBC modules & modular fixture for making continous

linear arrangement including cascading kit etc made up of extruded aluminium housing

having high efficiency diffuser with more than 85% transmittance, system lumen >3000

with luminaire efficacy 100LPW , CRI >80 ,UGR<22 CCT 4000K. The luminaire rated life

(L70) 50000 hours with inbuilt protection against short circuit,Miswiring,over voltage and

surge protection upto 3 KV PF.0.95 and THD<10% (Driver complaince IEC 62384,IEC

61547,IEC 61347-2-13)including making suitable arrangement for fixing including

connection with 3 x 1.5 sq.mm. PVC insulated FRLS PVC sheathed copper conductor etc as

Supply, Installation, Testing and Commissioning of Surface type 12W non-dimmable LED

clyndical downlighter neutral white (4000 K) with LED having pressure die cast aluminium

hang body having high efficiency diffuser with more than 85% transmittance with rated

life of L-70 @50000 hrs having system lumen output better than 1080 lumens,with

efficacy better than 90 lumen/ watt with CRI>80 & Driver efficiency> 90% (Driver

complaince IEC 62384,IEC 61547,IEC 61347-2-13,EMICISPR15, THD<10%,PF>0.95 ) etc.

with inbuilt protection against short circuit,Miswiring,over voltage and surge protection

upto 3 KV including making suitable arrangement for fixing complete as required

complete as reqd.

Supply, Installation, Testing and Commissioning of 20W/M LED flexible strip made of 240

LED / meter and Flexible FR4 PCB with copper contacts. CCT = 4000K, CRI >80.Drier

shoulb 12V DC, 10Amp contant voltage With aluminium extrusion casing.

Digitally signed by AMIT

39 Recessed PIR Motion Sensor Similar to Wipro Make : GLPS01R010HA or equivalent MR 12.00 Each 5,760.00 69,120.00

Brush Less Direct Current (BLDC) Motor

Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct

Current (BLDC) Motor, class of insulation: B, 3 nos. metal (Aluminum alloy) blades, 30 cm

long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body

Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM

(tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote DSR 2025

(preferably mobile app based) for speed control and all remaining accessories including 2.1.3

safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance

more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling Fan compliant

to IS 374:2019 fan Supply, earthing etc. complete as req 1200mm, service value ≥ 6.0

CM/Min/Watt, air delivery 210 CM/Min (Minimum)

Supply Installation Testing and Commissioning of 400mm sweep 1500RPM energy

41 efficient BLDC fan with double ball bearing for longer life similar to CGE RENESA or RA-2 1 Each 5,348.85 5,348.85

Online UPS- Input supply: Three Phase, Output supply: Three Phase

Supplying, installation, Testing & Commissioning of of following capacity at full load (Unity

Power Factor) at operating temperature 0 to 40 deg C, Relative humidity 0 to 95%, Online

double conversion true sine wave Uninterrupted hot swappable (allow for the

replacement or addition of battery modules without shutting down the entire system)

modular Power Supply (UPS) system with N+1 modules (N denotes total number of

moduels requird for rated capacity). The UPS shall include a Rectifier, inverter, battery

42 bank suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 26.2

VAH per KVA of UPS rating per Hour backup time) on full load (Battery shall be VRLA, SMF

in ABS Container) and Static Bypass switch alongwith provision for manual bypass,

suitable isolation transformer for additional protection against neutral faults etc. UPS

shall have inbuilt

phase sequence correction. The UPS systems offered are to be of the latest technology

with Digital Control Microprocessor based for reliable operation using Insulated Gate

Bipolar Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with PWM (Pulse

Width Modulation). The quality of design, manufacturing and inspection process should

confirm to the relevant International standards such as IEC/EN/VDE. The operating

efficiency of the UPS systems shall be >96% while operating on battery mode and

delivering quality power to the 100% non-linear loads. Current total harmonic

effect(ITHD) on the input grid shall be < 5% at 50 %load. (The required LC (

Digitally signed by AMIT

inductor (L) and a capacitor (C)) filters shall be included in UPS cost),

extreme power factor kit to be included to limit the input power factor (PF) to 0.99 and

output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ),

however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads.

UPS shall be suitable for incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC

Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins,

Sine wave output. Non condensing, noise level less than 60db at 1 meter distance,

protections: Input Under voltage over voltage, abnormal out voltage, battery over

charging, output over current, short circuit protection, battery deep discharge protection,

10KV surge. UPS must comply with low voltage electromagnetic compatibility (EMC)

achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency

Independent (VFI)-type UPS. Communication RS232/RS485/SNMP port open protocol for

integration, all hardware & software for iOT Communication as per approved by

Engineering in charge. Required battery racks and interconnecting copper conductor

cables of suitable size and connectors and all required accoseries are inclusive of the

cost). This system must provide a means for logging and alarming of all monitored points

plus email notification. Forced air-cooling with integral inbuilt fans with redundancy (if

one fan fail UPS should be able to handle at least 80% of the load, Noise Level 65 DB at 1

meter distance. The system shall be in compliance IEC 62040- 1,2 & 3, IS: 16242 and

CPWD Specification. Display Panel (minimum) (In-build 5 inch or more LC Display / LED )

to display : a) Input: Voltage, current, Frequency. b) Bypass: Voltage, Frequency. c)

Output: Voltage, frequency, Current.

d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage.

f)Temperature: STS, Inverter, PFC. g) Event Logging & Statistical Data (On LCD/LED): UPS

should capture and display up to 3000 events like: Over temperature / DC Bus Fail / Fan

Fail / Fuse Fail / Overload / Short-circuit / Device Fail / Inverter Fail / Rectifier Fail /

Bypass Fail, etc. h) Statistical Data: No. of power failures / Transfers to Bypass / Total

Running time, etc. i) Mains Mode of Operation /Battery Mode of Operation / Bypass

feeding the load /UPS Fault /Battery charging and discharging, overload, battery voltage

and battery capacity. j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS Overload,

Fault, Shutdown, Input Over, Under Voltage, Output Over, Under Voltage, Battery Over,

Under Voltage, Over Load and short circuit, Over Temperature. The UPS should have QR

code which should contain drawing, test report OEM manual,Geo- Tag of manufacturing

10KVA (Each Power module shall be < 10 KVA) 26.2.1 1 Set 208893 208,893.00 -

Digitally signed by AMIT

SITC of LT switchgear panels suitable for 433 V, 3 phase, 4 wire, 50 Hz power distribution

system. The panel shall be Indoor, free standing, floor mounting, sheet metal clad,

cubicle, dead front, dust and vermin proof type compartmentalised design fabricated out

of 14 SWG CRCA sheet steel, complete with colour coded, heat shrinkable PVC insulated,

aluminium bus bars and separate earth bus bar of adequate cross section through out the

length of the panel. The incoming and outgoing feeders shall be accommodated in a fully

segregated, modular multitier arrangement with adequate size and distinct cable alley,

bus bar alley/chamber. The panel shall be complete with name plate, earthing,

numbering, danger plate etc. as per specifications and drawings as required. The panel

shall withstand the fault level of 50kA as per Single Line Diagram. The Panel shall also be

capable to communicate status like ON/OFF/ Trip through Modbus/Ethernet for major

component like ACB, MCCB, MCB & Multifunation meters.

The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3 phase, 50

Hz, 3 phase 4 wire supply system. Panel shall have Buscoupler switching, auto operation

of incommer and bus coupler, auto start of D.G. Sets, auto D.G. running by pre set timing,

auto changeover etc and having following incomming and outgoing Air Circuit - -

Breakers,microprocessor release for overload, short circuit, instantaneous & earthfault

protection with Current & Voltage metering & LCD display.

Air Circuit Breaker with microprocessor release ge metering & LCD display , with ready to

clsoe indicator, should have capability to communicate ON /OFF/ Trip Status on

Modbus/Ethernet and as per the detail specification of ACB (Icu=Ics=Icw=65 KA (1 sec).

MCCB, with microprocessor release with LSIG protection functionand should not derate

upto 50 decree Centrigrate as per testing guideline as per IEC 60947-2 and all the ACB - -

upto 2500Amp ACB should have same frame size LCD display for fault trip history, haivng

current limiting feature, double break mechanism & capability to communicate ON /OFF/

Trip Status on Modbus/Ethernet. (65 KA Ics)

Digitally signed by AMIT

1 Nos. 160 Amp TPN MCCB 25KA LSIG having S/C, E/F O/C protection, LCD Display having

specs as per attached annexture From 100KVA Transformer having

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zone Slelective Interlocking function

Multifunction Meter

1 Nos. 63 Amp TPN MCCB 25KA LSIG having S/C, E/F O/C protection, LCD Display having

specs as per attached annexture From 100KVA Transformer having

R,Y,B Phase indication Lamp with control MCB

On, Off, Trip Status Indication with control MCB

Inbuilt Zon ꁲҩ⦦ ꂔҩ⦦ ꂶҩ⦦ ꃘҩ⦦ ꃺҩ⦦ ꄜҩ

Buscoupler: 63 Amp FP MCCB

Outgoings - -

1 Nos. 100 Amp FP MCCB 25 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

STP + PL + Spare

2 Nos. 63 Amp FP MCB 25 KA

On, Off, Trip Status Indication with control MCB

Multifunction Meter

3 Nos. 32 Amp DP MCB 10 KA

On, Off, Trip Status Indication with control MCB - -

Multifunction Meter

Short Circuit Breaking capacity should not less than 50KA. - -

RELAYS AS PER SLD - -

Digitally signed by AMIT

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF MINISTRY OF MINES, 9TH FLOOR, NEW DELHI

ABSTRACT OF COST

NAME OF WORK -HVAC WORK

DSR -2025 Unit QTY RATE (RS.) RATE (RS.) MR AMOUNT (RS.)

Sr.No. Description AMOUNT

Supplying , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with

Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell

elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to

ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180-

260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air

32.2 circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated

capacity upto 42 0C. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed

Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International

Electrotechnical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993

and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to

1 operate up to 50 0C (out door ambient temperature).

Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical

cable IS 694 or IS 9968 temperature sensing control IS /International Electrotechnical Commission (IEC) 60730,

hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per

CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient

32.2.2 1.5 TR with 5 Star BEE Rating No. 1 43539.0 43539.0

32.2.4 2.0 TR with 5 Star BEE Rating No. 1 57396.0 57396.0

Inverter Type - Hot & Cold

32.2.6 1.5 TR with 3 Star BEE Rating No. 5 41768.0 208840.0

CASSETTE TYPE SPLIT UNITS

Supplying, Installation, Testing and Commissioning of Air Cooled Cassette type Air conditioners complete with Indoor

unit(IDU), Out door unit (ODU), R-32/R410A/R-407 Green Refrigerant, wireless Remote, inbuilt drain pump, suitable

for 400/230V, 50 Hz ,1 /3 phase AC supply, including surface / concealed copper Refrigerant piping with insulation

(closed cell elastomeric nitrile rubber tubular pipe section) upto 5.5 Mtr (IDU to ODU), copper power and control

cable upto 5.5 Mtr (IDU to ODU) including drain pipe, the system shall be capable of performing cooling,

32.4 dehumidification, Air circulation, filteration & ventilation of following capacity with Scroll/rotary compressor with min

5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB) as

specified. The system shall be able to deliver 100% of the rated capacity as per relevant IS Code. The lab testing

reports as per IS: 1391 shall be submitted from National Accreditation Board for Testing and Calibration Laboratories

(NABL) accredited as per International Electrotechnical Commission (IEC) 17025 standards/Central Power Research

Institute (CPRI)/ Electrical Research and Development Association (ERDA)with Original Equipment Manufacturer

2 (OEM) etc. complete as per CPWD specification and as per IS: 1391 as required.

Heating & Cooling

32.4.7 1.5 TR with 3 Star BEE Rating No. 2 60141.0 120282.0

32.4.8 2.0 TR with 3 Star BEE Rating No. 4 67052.0 268208.0

32.4.9 2.5 TR with 3 Star BEE Rating No. 6 80764.0 484584.0

3 7.14 COPPER REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of

following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete

with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including

accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric

nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid

lines, all accessories as per specifications etc. as required :

3.1 7.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 3 224.5 673.4

3.2 7.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 35 303.4 10618.1

3.3 7.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 4 427.0 1708.0

3.4 7.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 25 539.2 13480.9

Digitally signed by AMIT

DSR -2025 Unit QTY RATE (RS.) RATE (RS.) MR AMOUNT (RS.)

Sr.No. Description AMOUNT

3.5 7.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 15 648.0 9719.4

3.6 7.14.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 2 792.6 1585.3

4 MR-1 Drain Piping :

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.

Supplying and drawing following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in the existing

5 1.17 surface/ recessed steel/ PVC conduit as required.

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for

6 MR-2 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of

4.1 Supplying and installaton following size of perforated painted with powder coating M.S. cable trays

with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended

from the ceiling with two numbers MS/GI Suspenders i/c base of suitable size MS/GI angle, bolts &

nuts, painting suspenders, fastener etc as required.

7.1 4.1.1 100 mm width X 50 mm depth X 1.6 mm thickness Rmt 5 623.0 3115.0

7.2 4.1.2 150 mm width X 50 mm depth X 1.6 mm thickness Rmt 5 686.0 3430.0

Digitally signed by AMIT

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF MINISTRY OF MINES, 9TH FLOOR, NEW DELHI

ABSTRACT OF COST

NAME OF WORK - FIRE ALARM &PA

I.NO DSR COD- DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

SH 1.00 FIRE ALARM

1.0 Supplying, installation, testing & commissioning of intelligent analog addressable EACH 22.00 3004.00 66088.00 0.00

28.2.4 photothermal detector complete with mounting base complete as required.

2.0 Supplying, installation, testing & commissioning of response indicator on EACH 10.00 306.00 3060.00 0.00

28.2.5 surface/recessed MS Box having two LED, metallic cover complete with all

connections etc as required.

3.0 Supplying, installation, testing & commissioning of intelligent addressable thermal EACH 1.00 2866.00 2866.00 0.00

28.2.9 detector with rate of rise cum fixed tempreature thermistor complete with base as

4.0 Supplying, installation, testing & commissioning of fault isolator complete with EACH 5.00 3434.00 17170.00 0.00

base as required.

5.0 Supplying, installation, testing & commissioning of addressable fire control module EACH 1.00 3156.00 3156.00 0.00

complete as required

6.0 Supplying, installation, testing & commissioning of addressable phone control EACH 2.00 3242.00 6484.00 0.00

module complete as required.

8.0 Supplying, installation, testing & commissioning of addressable horn cum strobe EACH 2.00 3682.00 7364.00 0.00

complete as required.

9.0 Supplying, installation, testing & commissioning of addressable manual call point EACH 2.00 4063.00 8126.00 0.00

complete as required.

10.0 Supplying, installation, testing & commissioning of 6 zone, voice alarm controller EACH 1.00 132115.00 132115.00 0.00

with USB, MP3 player (including 6 zone button paging station) with seamless

integration facility with main fire alarm panel for voice evacuation complete as

11.0 Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated Meter 210.00 192.00 40320.00 0.00

28.5.2 with annealed copper conductor having XLPE insulation, steel wire armouring &

FRLS outer sheath complete as required

12.0 Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all Meter 175.00 60.00 10500.00 0.00

ancillaries and accessories like coupler etc. as required.

13.0 Supplying & Fixing of battery operated illiminated "EXIT" signage, with 2hrs power EACH 3.00 3870.00 11610.00

Battery backup complete as required.

14.0 Supply, Installation, Testing and Commisioning of Loop Card capacity of 159 EACH 1.00 92150.00 92150.00

detectors For BMS Fire integration compatible with existing system

CLA Digitally signed by AMIT NBCC

15.0 Supply, Installation, Testing and Commisioning of Interface Card for BMS fire EACH 1.00 55500.00 55500.00

integration compatible with exisiting system

16.0 Supply, Installation, Testing and Commisioning of repeater panel having 640 EACH 1.00 90000.00 90000.00

character liquid crystal with backlit control compatible with existing system

Note - item to be applicable in urban areas having directions for restricted hours

for movement/ plying of load carrying motor vehicle of 3.5 cum or more.

Total Carried Over to Abstract for Sub Head: 1.00 Fire Alarm : 297249.00 249260.00

SH 2.00 PA SYSTEM

1.0 Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker EACH 16.00 1025.00 16400.00 0.00

complete as required.

2.0 Supplying, installation, testing & commissioning of digital audio amplifier 150 EACH 1.00 101150.00 101150.00

Watt, 25V rms operating at 240 Volt AC Supply complete as required.

3.0 Supplying and drawing of cable Fire Retardant PVC insulated copper conductor

cable in the existing surface / recessed steel conduit of following pairs, cores and

size including connections and interconnections etc. as required.

28.5.3.2 speaker cable Two pair, 2-core, 1.5 sqmm METER 197.00 97.00 19109.00 0.00

4.0 Supplying, installation, testing & commissioning of Voice command keypad 6 zone, EACH 1.00 85450.00 85450.00 0.00

with microphone assembly complete as required.

Total Carried Over to Abstract for Sub Head: 2.00 Pa System : 222109.00 0.00

Grand Total 519358.00 249260.00

Grand Total 519358.00 249260.00

CLA Digitally signed by AMIT NBCC

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF MINISTRY OF MINES, 9TH FLOOR, NEW DELHI

ABSTRACT OF COST

WORK: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

I.NO DSR CODE DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT

Providing and fixing ISI Marked of approved make Fire Extinguishers complete with all accessories as per

manufacturer's specifications.

Providing & fixing of CO2 High Pressure trolley mounted 6.5 kg Fire Extinguisher, filled with Co2 Gas as per

IS 15222, Gross Weight 23 Kg, empty weight 16.5 Kg, Control discharge mechanism fitted with 2 Meter

Wire Braided Hose & Flat Horn with Diffuser Nozzle for dispersed discharge of CO2, Discharge Time 25 Sec,

Average Discharge is 95%, applicable on Class B, C and electrically started Fire, Internal coating is not

applicable & External coating is of enamel spray painting, Valve Confirm to IS 3224 ISI Marked, CO2

Cylinder construction: hot spinning by seamless pipes & bearing ISI mark, Body confirms to IS 7285 and

PESO APPROVED, Extinguishers confirmed to IS 16018:2012 and ISI maked. Fire Rating: 55B

Providing and fixing of Water type cartridge operated 9 ltr. Fire Extinguisher. Applicable fire class A,UTGS

Pressure Gauge, Gross Weight 13 Kg, empty weight 5.3 Kg, Can Height 585mm, Diameter 180 ± 10mm,

Discharge Time 35 Sec, Controllable discharge mechanism, Jet Range 7 Meters, Average Discharge is 95%,

Fire Rating- 3A, Can Construction : Deep drawn & CO2 Mig welded, CE Marked Valve with inbuilt NRV &

Safety Release Provision, Controllable discharge mechanism with EPDM Hose & Nozzle, CO2 gas Cartridge

of 60 gm. Internal Plastic Lining and External Coating - Pure Polyester Powder coating (UV Resistant), Made

up of 2 mm Sheet, As per IS 5683:2018 and ISI Marke

c) MR-4 ABC dry powder stored pressure type 6 kg capacity (IS:15683). NOS 4 4746.13 18984.50

Fire Fighting Digitally signed by AMIT NSL

Name Of Work -CCTV Surveillance System Work

SI.No DSR-2025/MR Particulars Qty Unit MR Rate DSR Rate DSR Amount MR Amount

SUB HEAD :1 CCTV Surveillance Work - -

Supplying Installation Testing and Commissioning of

5/6MP IP IR Dome Camera having following

specifications and features etc :-

1)Type of Camera: Dome Camera 2) Image Sensor: 1/2.8" or better progressive Scan

CMOS get color image even at night condition 3) Signal System: PAL/NTSC

4) Minimum Illumination: 0.008Lux@ F1.4, AGC ON, 0 lux with IR or better

5) Imaging: 1/3s to 1/30000s Shutter Support, Auto Gain Control , White Balance- Auto,

Back Light Compensation, Multi zone Privacy Masking, HLC,

Digital Watermarking. 6) On Screen Display: Camera should display Camera

title, Date & Time in live & recorded video both. 7) Signal to Noise Ratio: > 50 dB

8) Day & Night: True Day & Night High Performance Mechanical IR cut filter with auto

switch, IR Source- Inbuilt IR LED's with effective distance upto 50 Mtrs integrated IR 30

1 40.5 Mtrs for colour view in night. 9) Video Compression (Minimum): H.265 or better,

Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723 10) Wide Dynamic Range: WDR (120dB or

more) 11) Digital Noise Reduction: DNR (2D/3D) On/Off 12) Streaming: Triple streaming,

configurable 13) Video Streaming & Frame Rates: Triple streaming

, configurable Main stream: 5/6MP @25/30 fps, Sub streams: D1@25/30 fps or better

14) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable

through client software or web browser 15) Profile Management: User configuration

import, export 16) Security: User Authentication, Water Marking 17) Onboard Storage:

Camera should support built-in Micro SD/SDHC/SDXC Card slot upto 512 GB. It should be

supplied with minimum 128GB memory Card. 18) Recording Management: Format SD,

overwrite, storage management, video to NAS device,

Digitally signed by AMIT

19) Edge Analytics : Tripwire, Intrusion, Motion Detection 20) Alarm Trigger :

Motion/tampering detection; network disconnection detection; IP conflict detection;

memory card state detection; memory space detection 21) Alarm Support: It should have

1/1 Alarm In/ Out Port 22) Audio Support: It should have 1x Built-In Mic and

1/1 Audio In/ Out Port for external Mic. and Speaker (As per site requirement) with

G.711U/A/ G.711Mu/ AAC/ G.726 audio compression 23) Network Protocol: SFTP, IPv6,

IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP,

SMTP, RTSPS, unicast, 24) System Capability: ONVIF 25) VMS: Camera shall support open

source VMS 26) Cyber Security: trusted boot, AES 256-bit Encryption, Configuration

encryption, trusted execution, Digest, security logs, , account lockout,

video encryption, IP/MAC filtering, HTTPS, trusted upgrade. 27) Ethernet: 1 RJ 45 10/100

Ethernet port 28) Power Input: The camera should support simultaneous dual power

input—12 VDC (via power adapter) and PoE—to ensure continuous operation in

the event of a failure in one power source. 29) Power Requirement: 12VDC/24VDC/PoE

(802.3af)/ePoE 30) Enclosure: IP67 weather proof, IK10 31) Operating Condition: Ambient

Temperature:- (-) 05°C to 50°C, humidity 95% (max) (non-condensing)

32) IR life: 40000 hours or higher 33) Video Bit rate: 32 KBPS - 8 MBPS or better

34) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS

5MP/6MP IP IR 2.8/ 3.6/6/8/12 mm fixed lens (as per 128,000.00

site requirement) Dome Camera.

Supplying Installation Testing and Commissioning of following Channel Network Video

Recorder (NVR) with camera licenses to record for all channels having

specifications and features etc as mentioned below :

2 40.10 1) Network Video Recorder Embedded/ Installed OS (Linux) along with Camera Licenses for

number of channels of NVR to record per NVR and to provide a live view, storage and

simultaneously Multi-channel playback of all IP, IR camera or more and must be ONVIF

with minimum support of 256Mbps incoming Bandwidth.

Digitally signed by AMIT

2) NVR should support H.265 or better, H.264, MJPEG, MPEG4 support

3) Must support 1 channel Input, 1 channel Output, RCA for Two-way Talk

4) Intelligent auto power on when power resumes after power outage.

5) Storage: It should support minimum 2 SATA Slots with 20TB capacity/ Slot.

6) Connectivity Interface : 1 Nos. x 10/100/1000 Mbps Ethernet Ports, 1x RS485, 1x RS232

7) Backup Interface : Its should have 2 Nosx USB port

(1x USB3.0, 1xUSB2.0), 8) Video Output Ports: 1x HDMI and 1 VGA

9) Alarm Ports: It should have 4/1 Ch In/ Out ports to connect various type of external

sensors and output devices like hooter/ Siren etc.

10) Email & SMS Altert options: Option for SMS/ Email Alerts to minimum 5 designated

mobile number for power failure, HDD failure, vandalism, tempring, network disconnection

and panic 11) Web & Mobile Application: Web, Mobile app ( For

iPhone, iPad, Android Phone) for alerts and viewing. 12) Protocols: HTTP, HTTPS, TCP/IP,

IPv4, UDP, NTP, DHCP, DNS, SMTP, UPnP, DDNS, Alarm Server, IP Search, Multicast, Auto

Registration, ONVIF (Profile T, Profile S, Profile G), CGI, SDK and OEM

Cloud for remote monitoring without any public IP need. 13) Standards: CE, FCC, RoHS and

BIS Certified 14) Power Supply : Should support 12VDC, 4Amp or AC100-240V, 50/60Hz

Power supply. 15) Operating Condition : Ambient Temperature (-5°C

to 50°C), humidity 90% (max) (non-condensing) 16) The VMS, NVR application shall support

all the features & functionalities of the offered cameras. 17) VMS should consist of Base

license and Channel Licenses. VMS should be provided with camera

Licenses , with no dependency of VMS licenses by binding with the MAC address of the

cameras to achieve the functionality. 18) The NVR OEM shall be responsible for providing a

mobile application compatible with both Android and

iOS devices, enabling remote monitoring and playback

of cameras/NVR footage.

Digitally signed by AMIT

19) The OEM must provide its own DDNS server hosted in India, eliminating the need for a

public IP address for remote monitoring over the Internet. 20) Must support Resolution:

1024×768 21) Must support recording resolution upto 32MP 22) Must support Continuous,

Alarm, Motion, Instant, Panic Recording Mode 23) When alarm recording is enabled and an

event occurs, you can click the alarm icon on monitoring

page to view the alert details. The snapshot function is supported on monitoring and

playback page 24) The Network Video Recorder (NVR) shall be configured to send email

whenever a system message is created or an alarm event occurs. The email server

shall be a valid SMTP server. Each recipient email address shall be configured to receive any

combination of critical, warning, or informational messages or alarm notifications. When

an alarm occurs, the email message includes the NVR name, time of alarm and a list of

camera that is configured to record upon alarm 25) It should support Network Support:

HTTP, TCP/IP, SMTP, DHCP, DNS, DDNS, FTP, NTP, UPnP, Multi

IP Setting. Convert multiple recording files to one avi/MP4 file. 26) General AI Based

Search: Search Pictures by channel, time, event type, target classification (Fall

Detection, People Approach Detection, People No. Exception Detection, People Staying

Detection, Violence Detection. 27) Alarm Notifications based on: Motion detection,

video tampering, video loss, scene changing, PIR alarm, Camera external alarm, Face

detection, face recognition, perimeter protection (intrusion and tripwire), ANPR, people

counting, stereo analysis, crowd distribution, heat map, Disk Full, Storage Error,

IP Conflict and abnormal behavior of fan 28) Alarm Notification should be linked with

Recording, snapshots, Camera external alarm output, buzzer,

logs, presets and email.

Digitally signed by AMIT

29) Built-In Artificial Intelligence: NVR should have built-in AI :- - 2 Channel face detection

and recognition, - Minimum 4 Channel perimeter protection, - Minimum 8 Channel Smart

Motion Detection 30) Face Recognition Database Capacity: It should

support total Blacklist and Whitelist capacity of Minimum 20,000 Faces or more with Face

Detection speed of 12 face images/sec. 31) Face & Human Attributes Search: Search

Pictures/ Video by Gender, age group, glasses, expressions, face mask, beard, Top color,

top type, hat, bag, age, gender and umbrella. 32) ANPR Capability: It should support ANPR

Camera with License plate, plate color, vehicle body, vehicle

model, vehicle logo, calling, seatbelt, vehicle registration location etc vehicle attributes.

33) Alarm Notifications based on: Motion detection, video tampering, video loss, scene

changing, PIR alarm, Camera external alarm, Face detection, face recognition, perimeter

protection (intrusion and tripwire), ANPR, people counting, stereo analysis,

crowd distribution, heat map, Disk Full, Storage Error, IP Conflict and abnormal behavior of

fan, cybersecurity exception 34) Alarm Notification should be linked with Recording,

snapshots, Camera external alarm output, buzzer, logs, presets and email. 35) General AI

Based Search: Search Pictures by channel, time, event type, target classification (Fall

Detection, People Approach Detection, People No. Exception Detection, People Staying

Detection, Violence Detection. 36) Smart playback function: Should support smart

search for the selected area in the video and smart playback to improve the playback

efficiency 37) VCA (Video Content Analytic): Should support multiple video contented

analytics based on camera analytics

16 Channel Network Video Recorder (NVR) having display split :- Main screen: 1/4/8/9/16, 12,799.00

2nd screen: 1/4/8/9/16

Supplying, Installation, Testing and Commissioning following capacity Serveillance grade

Hard Disk with upto 256MB/s Transfer Rate, 256 MB Cache, 7200 RPM Disk Speed, 3.5 inch

form factor, SATA Interface, BSMI, ICES-003/NNB-003, CE, FCC, KC, Maghreb, RCM, UKCA,

VCCI, CB-Scheme, TUV, UL Certifications.

Supply, Installation, Testing & Commissioning of CCTV Client Operator Station with 1 No.of 1.00 Nos 75,000.00 75,000.00

55” LED Display - Complete as per specifications & approved by EIC

Digitally signed by AMIT

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF MINISTRY OF MINES, 9TH FLOOR, NEW DELHI

ABSTRACT OF COST

NAME OF WORK- AUDIO VIDEO

S.No. Item Specifications Qty CR1 Unit Price Total Price

Conference Room 27 Seater

SITC of 98" UHD Signage/Professional Display|500 Nits Brightness

|50000:1 Contrast Ratio|Operation: 24x7|1xVGA; 1xDP, 2xUSB 2.0 ,

4x HDMI 2.0 In, Secure USB 2.0 (Internal), RJ45, RJ12, RS232, Optical

SPDIF |1xHDMI 2.0, 1xDP Out, Supports Daisy Chain| Speaker 2x12 W

| Open Content Management Support, Scheduler, USB Autoplay,

AutoLaunch, HDMI-CEC, HDMI-Wakeup, Auto-switch on Failover,

Panel Lock, OSD Rotation, NoSignalPowerOff, Screen Saver, Pixel shift,

Scheduler, Videowall support, Remote control via LAN, Realtime

Clock, Joystick, Rocker Switch| Optional : OPS compatibility

|Certifications: Safety, EMC, CE

Supply, Installation, testing and commissioning of Ceiling microphone

with automatic dynamic Beamforming technology, The beam will

automatically detect the position of the person speaking and will

follow the person around the room at all times. It should have 2 x

Dante digital audio (Redundancy), Analog audio out (Phoenix 3-pin),

and Ethernet for Control and PoE connectivity ports. The coverage of

the ceiling microphone should be min 800 square feet or more. It

should have a true voice lift feature to increase audio intelligibility

MR-2 above the ambient noise floor. It should support IT industry standards 2 ₹ 562,187.85 ₹ 1,124,375.70

like IEEE 802.1x. It can be controlled through software that can control

and monitor the microphone in any network. It should have min 100

dB SPL, 5ms latency, and min 90dBA or higher dynamic range. High-

precision audio settings for maximum control, setting to exclude (min

5) and prioritize the areas of the room. It should certified from

Microsoft Teams and Zoom Video conferencing applications. It

should have UL 62368 certification (including UL 2043 testing and

compliance) and safety certifications.

Suppy Installation Testing and Commissioning of digital signal

processor with minimum 14no. Or more Mic / line input with phantom

power and AEC and 8 or more line level output, 1no. Or more GPIO at

least 2 channel of USB input and output for software Video

Conferencing, should have 64x64 channel of digital dante input

MR-3 output, Should have sampline rate of 48kHz or better, Should be 1 ₹ 716,250.00 ₹ 716,250.00

expandable for port expansion, should support Control with App via

iOS and Android devices, or any third-party control system, Shall have

Built-in filters, feedback suppression, AGC single-device(chassis) use is

permitted, but the combination of devices is not accepted etc

complete as required as per specifications

Supply, Installation, testing and commissioning of Quad channel

energy star rated digital power amplifier,Quad channel 4 Ohm or

8 ohm energy-efficient amplifier - 4 x 80W or more 70/100V

Technology : Class-D,Input linking through miniature switches,

Switching mode power supply, Protection : DC Short circuit &

Over heating & Over load & Signal limiting, Frequency Response

120 Hz - 20 kHz or better, Silent passive cooling etc complete

required as per specifications.

Supply, Installation, testing and commissioning of 6.5" two-way

coaxial thin edge ceiling loudspeaker having 100V transformer power

taps from 60watts to 15watts or better it should have metal back can

MR-5 Ceiling Speakers for premium performance in demanding applications, Conical 6 ₹ 35,105.00 ₹ 210,630.00

dispersion : 142° or more, Low impedance RMS continuous power of

60watts, impedance : 8 or less,frequency range (-10dB) : 70 Hz - 20

kHz, frequency response (±3dB) : 100Hz - 20KHz, Max SPL on 100v

should be 105dB or more etc complete required as per specifications.

Digitally signed by AMIT

Supply, Installation, Testing & Commissioning of Full HD PTZ

Camera supporting 1080p at 60 Frames per Second, minimum

12X Optical Zoom with FoV of 72 degree and minimum 255

presets. Camera should support simultaneous outputs through

MR-6 Camera HDMI, USB 3.0, IP/3G-SDI, Audio In and can be controlled via 1 ₹ 355,600.00 ₹ 355,600.00

RS232/422 and IP. Panning angle -170° ~ +170° , Tilting angle -30°

~ +90. Camera should support SRT, PoE & should be compatible

with Virtual USB Driver. OEM should be BIS, CE, Clickshare, RoHS

& FCC Certified with test lab report supporting the certifications

Supply Installation Testing and Commissioning of surface-mount USB-

to-Dante endpoint, two-way volume and mute sync for Microsoft

Teams,compliant with CE and FCC, device shouold have Power-over-

Ethernet (PoE) to IEEE 802.3af Class 0 standard and support Dante

USB to Dante networking using standard CatX cable, device should support the

Device Speakerphone profile with and without echo cancellation, enable two-

way volume and mute syncronization with both PC and Mac

platforms, Dante with AES67 compliance,Sampling Rate(s) 48

kHz,should be from same OEM as DSP etc complete required as per

specifications.

Suppy Installation Testing and Commissioning of control system with

touch panel/Ipad, 100/1000 Mbps, auto‑switching, auto‑negotiating,

MR-8 auto‑discovery, full/half duplex, industry-standard TCP/IP stack, 1 ₹ 488,750.00 ₹ 488,750.00

UDP/IP, CIP, DHCP, SSL, TLS, SSH, SFTP (SSH File Transfer Protocol),

FIPS 140-2 compliant encryption

MR-9 Supply, Installation, testing and commissioning of 16 port switch 1 ₹ 85,500.00 ₹ 85,500.00

Supply, Installation, testing and commissioning of HDMI RX extender

with complies with the advanced HDCP 2.2 and HDMI 2.0 standards,

uncompressed HD audio and video as well as control via a single run

of Cat.5e/6/7 cable over distances of up to 70 meters and upto 40mat

4K, HDBaseT feature support: HD Video and Audio, and Control

(IR/RS-232 pass-through) and CEC bypass, Supports pass-through of

many audio formats including LPCM (up to 8 channels), Bitstream and

Supply, Installation, testing and commissioning of HDMI TX extender

complies with the advanced HDCP 2.2 and HDMI 2.0 standards,

uncompressed HD audio and video as well as control via a single run

of Cat.5e/6/7 cable over distances of up to 70 meters and upto 40mat

4K, HDBaseT feature support: HD Video and Audio, and Control

(IR/RS-232 pass-through) and CEC bypass, Supports pass-through of

many audio formats including LPCM (up to 8 channels), Bitstream and

Supply, Installation, testing and commissioning of Cable cubby (1

HDMI, 1LAN,1 Charging socket)

Supply Installation Testing and Commissioning of HDMI Audio

Extractor should extract up to 2 channels of LPCM audio or 5.1

channels of Bitstream audio from an HDMI source, allowing the user

to convert high quality HDMI audio into more convenient analog

(LPCM 2.0 sources only) or optical signals for use with powered

speakers or non-HDMI AV receivers. Both the input and output HDMI

MR-13 ports should support 4K UHD resolutions up to 4K@60Hz (4:4:4, 8-bit) 1 ₹ 83,725.00 ₹ 83,725.00

and should capable of providing high quality audio and video

performance. The unit should supports passthrough of HD and

standard Bitstream formats as well as LPCM 7.1 with audio sampling

rates up to 192kHz. Built-in EDID management support allows the user

select from multiple EDIDs and, with the use of optional PC software,

to upload, download, or edit EDID files etc and complete as required

Supply, Installation, Testing & Commissioning of USB 3.2 Extenders.

Transmitter should have 1xUSB C input port, 1X RJ45, 1xUSB-A Output

Port. Receiver should have Input Port 1×Cat5e/6A/7 (RJ45). 1×USB-C,

MR-14 USB Tx Rx 3×USB-A Output Port. Bandwidth upto 5Gbps (SuperSpeed), 1 ₹ 74,800.00 ₹ 74,800.00

Tranmission distance upto 100M. Devices should be controlable by

the USB host on a transmitter. Should have backward compatibility

Supply, Installation, testing and commissioning of Four HDMI inputs

matrixed to Four HDMI outputs with HDMI 2.0a specification and

MR-15 18Gbps (600MHz) 4K UHD support, HD resolutions up to 1 ₹ 233,750.00 ₹ 233,750.00

bit Deep Color up to 1080p@60Hz.

MR-16 Cables Cables & connectors 1 ₹ 70,000.00 ₹ 70,000.00

Total Include GST ₹ 5,068,083.15

Digitally signed by AMIT

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF MINISTRY OF MINES, 9TH FLOOR, NEW DELHI

ABSTRACT OF COST

NAME OF WORK- ACTIVE PASSIVE

S. No. Description Item Unit Qty Rate Amoint

Supply, installation, testing, and commissioning of smart-managed network switch, which should

have the following features or better: 24 RJ-45 autosensing 10/100/1000 Mbps Gigabit Ethernet

ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T,

or better), 4 SFP/SFP+ uplink ports supporting 1/10GbE fiber transceivers (or better), a PoE+

power budget of 270 W (Class 4) or higher, and an internal power supply supporting input

voltage of 100–127 / 200–240 VAC, 50/60 Hz. The switch should provide a switching capacity of

128 Gbps or more, a forwarding rate of 95.23 Mpps or higher, and be equipped with an ARM

Cortex-A9 processor at 800 MHz or faster, with at least 512 MB SDRAM, 256 MB flash memory,

and a 1.5 MB packet buffer or better. It must support Layer 2 and Layer 3 features including

VLANs (minimum 256 or more), link aggregation, Spanning Tree Protocol, IGMP snooping,

Quality of Service (QoS), port mirroring, rate limiting, static routing, and advanced security

features such as IEEE 802.1X authentication, ACLs, and automatic denial-of-service (DoS)

protection. Management should be possible via Aruba Instant On cloud portal, mobile app, web

browser, and SNMP manager, with multiple privilege levels and password protection. The switch

must be rack-mountable (1U form factor)

Supply, installation, testing, and commissioning of smart-managed network switch, which should

have the following features or better: 48 RJ-45 auto sensing 10/100/1000 Mbps Gigabit Ethernet

ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T,

or better), 4 SFP/SFP+ uplink ports supporting 1/10GbE fiber transceivers (or better), a switching

capacity of 176 Gbps or more, and a forwarding rate of 130.95 Mpps or higher. The switch must

utilize an ARM Cortex-A9 processor at 800 MHz or faster, with at least 512 MB SDRAM and 256

MB flash memory, and a packet buffer of 1.5 MB or more. It should support Layer 2+ features,

MR-2 including VLANs (minimum 256 or more), link aggregation, Spanning Tree Protocol, IGMP Nos 1 ₹ 297,000.00 ₹ 297,000.00

snooping, Quality of Service (QoS), port mirroring, rate limiting, auto MDI/MDI-X, and advanced

security features such as IEEE 802.1X authentication, ACLs, and automatic denial-of-service (DoS)

protection. The unit should offer web-based, cloud, and SNMP management, with support for

management via Aruba Instant On portal, mobile app, or local web GUI, and provide multiple

privilege levels with password protection. The MAC address table should support at least 16,000

entries or more. The switch must be rack-mountable (1U form factor)

Supply, Installation, Testing and Commissioning of 24 Port POE+ Access Switch to provide 24 nos.

1G Base-T ports with minimum PoE budget of 270W and 4x 1/10GbE uplink ports. with at least

512 MB SDRAM and 256 MB flash memory, and a packet buffer of 1.5 MB or more, It should

support Layer 2+ features, including VLANs, Should have static, RIPv1, RIPv2, RIPng,OSPF,

MACSEC,802.1x , PBR and VRRP from day 1 & upgradable to support IS-IS, VXLAN & VRF.

Common Criteria Certification NDPP and Ipv6 Certification from day-1

Supply, Installation, Testing & Commissioning of LED 24 Port loaded Cat 6 Jack Panel,

Staggered 24 Port panel with All port LED in 1U Rack Unit, Copper Alloyed Contact Material, EIA Jack

568A/B wired, PC + glass fiber, UL 94V-0, black color, Front Port Labeling, 22-24 AWG Panel

Wire Accumulation etc. complete as required.

Supply, Installation, Testing & Commissioning of dual face plate having provision for one

MR-5 I/O along with spring type shutter for dust proof, made of ABS PVC plastic etc. complete as Nos 35 ₹ 259.00 ₹ 9,065.00

Supply, Installation, Testing & Commissioning of single face plate having provision for one

MR-6 I/O along with spring type shutter for dust proof, made of ABS PVC plastic etc. complete as Nos 10 ₹ 196.00 ₹ 1,960.00

Supply, Installation, Testing & Commissioning of CAT 6 Information Outlet, Universal label Cat

MR-7 permits T568A or B wiring, UL® Listed, meets all TIA and ISO requirements Complete in all Informati Nos 100 ₹ 550.00 ₹ 55,000.00

respect as required by the site etc. complete as required. on Outlet

Supplying, drawing, Installation, Testing and commissioning of CAT6 UTP LSZH 23AWG Twisted

Pair Cable in existing conduit/ on surface, Category 6 Unshielded Twisted Pair, 4 pair should be

complied as per UL/ETL verification program for compliance with ANSI/TIA-568.2-D standard. Cat Lan

Outer diameter should be in the range of 6.1mm nominal with Operating Temperature Range : - Cable

5° to +60°C, Bending Radius : < 4 X Cable Diameter at –5°C ± 1°C and Pulling Force : 11.5Kg etc.

complete as required.

Supply, Installation, Testing & Commissioning of CAT 6 Patch Cord LSZH 1 Mtr, 4 pair

26 AWG stranded copper wire, Pre-terminated with RJ45 plugs, Slim clear anti-snag slip on

MR-8 boots, Suitable for EIA 568A or 568B wiring, UL® Listed, meets all TIA and ISO requirements. Nos 100 ₹ 408.00 ₹ 40,800.00

Complete in all respect as required by site completion etc. complete as required.

Supply, Installation, Testing & Commissioning of CAT 6 Patch Cord LSZH 2 Mtr, 4 pair 26

AWG stranded copper wire, Pre-terminated with RJ45 plugs, Slim clear anti-snag slip on

MR-9 boots, Suitable for EIA 568A or 568B wiring, UL® Listed, meets all TIA and ISO requirements. Nos 50 ₹ 560.00 ₹ 28,000.00

Complete in all respect as required by site completion etc. complete as required.

Supply, Installation, Testing & Commissioning of Horizontal cable manager etc. Horizonta

MR-10 complete as required. l Cable Nos 4 ₹ 626.00 ₹ 2,504.00

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in

MR-11 surface/recess including cutting the wall and making good the same in case of recessed conduit

Digitally signed by AMIT

DETAILED ESTIMATE FOR PROPOSED CONSTRUCTION OF MINISTRY OF MINES, 9TH FLOOR, NEW DELHI

ABSTRACT OF COST

NAME OF WORK- EPBAX

Supply, Installation, Testing & Commissioning of Server based Communication System

with all the required Software licenses and Hardware - IP-PBX/IP Telephony

Communications Server: The IP Telephony Solution shall support the following Services -

Voice, IM, Presence and Audio Conference The IP Telephony Solution should support

H.323 / SIP The Solution should support the following Trunks - FXO, E1 PRI and SIP The IP

1 Telephony solution should incorporate all licenses for the Phones and Trunks Solution Nos 1 ₹ 1,950,000.00 ₹ 1,950,000.00

should support all Extensions from Day 1 with future scalability upto 500 users. Licenses

for all Phones supplied should be provisioned on Day1 Solution should support Hard 50 IP

Phones, 100 Analog Extensions, Rack mount architecture, complete as required and as

per technical specifications.or its equivalent specifications.

Supply, Installation, Testing & Commissioning of Color display—2.8 inches x 2.1 inches

(7.0 cm x 5.3 cm)—Diagonal width: 3.5 inches (8.8 cm)▪ 8 buttons with dual LEDs (red,

green)▪ 4 softkeys▪ Hard buttons for phone, messages, contacts, history, home,

navigation cluster,headset, speaker, volume, mute▪ LEDs for speaker, mute, headset,

message, history▪ 24 administrative buttons▪ Wideband audio in handset and headset▪

Full duplex speakerphone ▪ Ergonomic hearing aid compatible handset supports TTD

acoustic coupler▪ Message waiting indicator▪ Mute indicator with optional mute alerting▪

IC call alerting with 360- degree visibility▪ Rich, classic, alternate, and downloadable

ringtones▪ Dual-position stand, optional wallmount stand▪ Gigabit Ethernet (10 / 100 /

2 1000) line interface▪ Second Ethernet interface 10 / 100 / 1000 Mbps▪ PoE Class (IEEE Nos 5 ₹ 31,554.00 ₹ 157,770.00

802.3af) registers as class 1 device and supports 802.3az▪ Optional AC to 5 volt adapter▪

Order Custom Bezels / Faceplates▪ SIP & H.323 protocol support▪Standards-based codec

support: G.711, G.726, G.729A / B, G.722, Opus.▪ Zero touch deployment via Device

Enrollment Services Support▪ Supports the following languages: Arabic, Brazilian

Portuguese, Simplified Chinese, Dutch, English, Canadian French, Parisian French,

German, Hebrew, Italian, Japanese, Korean, Polish, Latin American Spanish, Castilian

Spanish,Thai, Turkish, and Russian. or its equivalent specifications

Supply Installation, Testing and Commissioning of Analog Speaker Phone with backlight.

or its equivalent specifications

Supply, Installation,Testing and commisioning of IP phone license complete as required.

Digitally signed by AMIT