REPAIR TO COMPOUND WALL, FOOTPATH, HARDSTANDING, INTERLOCKING KERBSTONE, CAMOUFLAGING TO BUILDINGS, ROOFING AT OMQ, OFFICERS MESS, AND OTHER MISC WORK UNDER GE (AF) SRINAGAR.

Amount

Contractor’s special attention is invited that work will be executed for up to triple story building. Quoted rates shall be deem to include for provision & removal scaffolding and necessary safety arrangement for workers employed

Demolition of Cement concrete (Unreinforced) of any description in ground floors and pavings n exe 15 cm thickness (below or above ground level) complete all as specified and as directed by the Engineer-in-Charge.

M&L for 75 mm thick plain cement concrete 1:2:4, type B- 2, using 40 mm graded stone aggregate, as in flooring, finished the surface even & smooth without using extra cement completed all as specified and directed.

M&L for 100mm thick plain cement concrete 1:2:4, type B- 2, using 40 mm graded stone aggregate, as in path / hard standing, finished the surface even & fair completed all as specified and directed.

M&L for 75 mm thick cement concrete 1:4:8, type D-2,(using 40 mm graded stone aggregate) as in Sub base for path / flooring complete all as specified and as directed.

M&L for 100 mm thick cement concrete 1:4:8, type D-2,(using 40 mm graded stone aggregate) as in Sub base for path / flooring complete all as specified and as directed.

Demolition of bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer) laid bedded and pointed dry complete all as specified and directed.

Demolition of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including rubbish off the premises, all as specified..

M&L for sand cushioning over PCC surfaces, for laying of interlocking tiles, spread rolled and consolidated to gradient as required complete all as specified and as directed.

Material & Labour for machine pressed precast concrete interlocking paver block of approved shape and size of 60 mm thickness, with minimum compressive strength of 35 N / Sqmm (M-35 grade), without correction factor for chamfering, made in rubber moulds with 0.50 mm thick scratch proof lacquer coating on top surface, with grey cement and no pigment, conforming to IS 15658 laid in path / hardstanding complete Note:- Sand screed will be measured & paid seperatly.

M&L for screed bed or bedding layers of 15 mm thick for laying floors in CM 1:4 complete all as specified.

M&L for 10 mm thick rendring / backing coat in cement mortar (1:4) to receive wall tiles, complete all as specified.

M&L for rubbur molded glossy finish Chequered cement concrete tiles of size 30 cm x 30 cm x 25 mm thick, in white cement with pigment, set, jointed in neat cement slurry & pointed in coloured cement, as in floors / path / hardstanding, laid over screed bed complete all as specified and directed.

M&L for coloured glazed ceramic tiles for wall cladding of size 148.5 x 450 x 8 to 10 mm thick of approved pattern / designed, set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

Material and labour 1st quality homogeneous vitrified parking tiles in approved shade in minimum 10 mm thickness area of each tile exceeding 0.08 sqm but not exceeding 0.18 sqm in floors etc, set & jointed in neat cement slurry & pointed in matching coloured polymer cement based grout to match complete all as specified and directed by Engineer-in-Charge. Make :Johnson Endura meteor (Korneto Biege) or equivalent make mention in Appx A.

M&L for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including half round molding of exposed edge complete all as specified.

Material & Labour for road side kerb with factory made Precast cement concrete block of mix 1:2:4 type B-1 using 20 mm graded stone aggregate, not exc 100 mm in thickness & set in CM 1:3 including making joints with or without grooves (thickness of joints except at sharp curve shall not be more than 5 mm), including making drainage opening wherever required complete.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F mild steel framed work such as ornamental and intricate design grills, gratings, etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways; railings, and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed / approved by Engineer-in-Charge

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified

Demolition of Brickwork / stone masonery work built in cement mortar including all quioins, arches, pillars etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for brickwork with subclass `B` bricks, in straight or curved on plan exc 6 m mean radius, built in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 21 above here-in-before but except bricks. Note:- Old brick retrieved vide item No 20 above shall be reused.

M&L for Brick work with sub class ‘B’ bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 using old size bricks complete all as specified and as directed by Engineer-in-Charge.

Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed by Engineer-in-Charge

M&L for rendering 15 mm thick in cement mortar 1:4 on brick / concrete surface of walls, finished even & smooth without using extra cement complete.

M&L for preparation of old painted surfaces of walls including sides and soffits of beams, fascias, parapets etc and applying one coat of cement base paint, colour and tint as ordered, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted surfaces of walls including sides and soffits of beams, fascias, parapets etc and applying two coat of cement base paint, colour and tint as ordered, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces of walls including sides and soffits of beams, fascias, parapets etc and applying two coats of cement base paint over a coat of primer, colour and tint as ordered, complete all as specified and directed by Engineer-in-Charge.

Complete removal of exsting treatment from wall surface including pilister & cornice etc of any descreption including cleaning brooming down or with steel wire brushing, scrapping down smooke soot, moulds, moss and efflorescent salts etc complete all as specified and as directed.

M&L for preparation of new plastered surfcae / surface obtained after complete removal of treatment and application of water based primer sutable for weather proof exterior emulsion paint, applied as per manufacturer instruction on wall surface including pilister & cornice etc of any descreption complete. Note:- This item will be executed over new plaster surface / surfcae obtained after complete removel of existing treatment.

M&L for application of two coats of exterior emulsion paint in camouflage pattern applied as per manufacturer instruction on primered surface of wall including pilister & cornice etc of any descreption complete. Note:- Application of primer will be measured & paid seperatly.

M&L for Preparation of old painted steel and iron roof surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint in camouflage pattern all as specified and directed by Engineer-in-Charge

M&L for Preparation of Old decorated surfaces of wall including cleaning brooming down or with steel wire brushing, scrapping down smooke soot, moulds, moss and efflorescent salts cleaning oil and geasy spots, trading oil, greasy spots etc and applying one coat of white wash complete all as specified and as directed.

M&L for Preparation of Old decorated surfaces of ceiling including cleaning brooming down or with steel wire brushing, scrapping down smooke soot, moulds, moss and efflorescent salts cleaning oil and geasy spots, trading oil, greasy spots etc and applying one coat of white wash complete all as specified and as directed.

Dismantling posts or struts (R.C.C.) any section, including taking out embedded portion and making good disturbed ground (Posts embedded in, Concrete, brick work, masonry, etc.) complete all as specified.

Dismantling chain link fencing fixed with steel or wood fillets, of any type complete all as specified

Excavating in post holes (or similar holes) each not exc 0.5 cu.m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance not exc 50m and making good surface, work in soft/loose soil, complete all as specified

M&L for mild steel work in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165, complete all as specified and directed.

Supply only chain link fencing galvanized steel wire aparure of size as directed, made up into mattresses or cages lapped wired conforming to IS 2721 all as specified & directed. Note:- Fixing only fencing will be measured and paid separately.

Fixing only chain link fencing of description fixed to steel post with mild steel flat & nut bolt etc. Note: (i) Supply only fencing, will be measured and paid separately. (ii) Supply and fix mild steel nut bolt, line wire and flat will be measured and paid separately.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm but n exc 10 cm long & diametre 5 to 10 mm, all as specified.

M&L for PCC 1:3:6 type C 2 using 40mm graded stone aggregate as in foundation, filling, mass concrete complete.

M&L for Reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in coping and the like, weathering, slightly rounded or chamfered angles including necessary form work complete. Note:- Reinforcement steel will be measured & paid seperatly.

M&L for mild steel TMT bars 10 mm dia and over cut to length bent to shape including cranking bending spirallay for hooping for columns hooking end and binding with and including mild steel wire (annelead) not less than 0.9mm dia or scuring with clips.

M&L for cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in coping and the like, weathering, slightly rounded or chamfered angles including necessary form work complete.

M/S Thakur & Sons

M/S LUCKY BUILDERS

M/S BASHIR AND SONS

M/S GULZAR ENTERPRISES

M/S M B ENTERPRISES

M/s PARVAZ CONSTRUCTION COMPANY

M/S LATIF AHMAD MIR

M/S Abdul Ahad Rather

NAJAR ENTERPRISES