Interior work for office of Election Commission of India, at 1st Floor LIC , Jeevan Tara Building, Parliament Street, New Delhi

S NO DSR/ MR DESCRIPTION QUANTITY UNIT RATE

DSR ITEM NON DSR ITEM

1 FLOORING WORKS

Providing and laying in position CEMENT CONCRETE of specified grade exluding the cost of centring and shuttering-all work upto plinth level.

4.1.8 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) 5.00 Cum 6326.05 31630.25

WOODEN FLOORING Panel 1820x145 Total thickness 14 mm Numbers of panels per pack 6 Nested Lengths Max. 1 plank out of 6 m2 per

pack 1,583 m2 Kg per pack 11,99 kg Toplayer PEFC controlled sources EN 13489 ± 3 mm Core board PEFC controlled sources Spruce

Backing layer PEFC controlled sources Wood Veneer 2 mm Tongue and groove Length Uniclic Width Uniclic Multifit Domestic use Conditions

in each pack 33 years Uniclic - Multifit connection Lifetime Commercial On request "Wood for Life" Edge Protect + Provides a warranty on build-

up of residue dirt along the edges due to maintenance over the years 10 years "Wood for Life" Surface & Edge Protect + (lacquered products

Supply of 100 mm Aluminium (Grade 6063) Skirting with 15 micron anodising In Natural Finish. Thichness 1.30 to 1.50 mm. Designed to

1.04 MR conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and Gasket. 170.00 Rmt 286.45 48696.19

TOTAL FLOORING WORKS

2 FALSE CEILING WORKS

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S.

sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide

x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x

50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to

centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450

mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x

230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm

2.01 12.45 long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm

interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230

mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound ,

jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for

board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with

frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the

cost of painting with

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

300MM X 1200MM MINERAL FIBRE GRID - Providing and fixing of mineral fiber ceiling tiles, with hot dipped galvanized steel grid

work , surface chemically cleaned capping pre-finished in baked polyester paint, Main Tees of size 38 (H) x 15 mm every 1.2M

centre to centre, centre to centre to form a grid of size 1200 X 300 mm and suspending the grid from RCC roof using 3 mm GI rod, 6

MR mm nylon rawl plug and 6mm J bolt at every 1200 mm intervals. And laying mineral fiber Acoustic ceiling tiles MV B-Pin of size 1200 x 260.00 Sqm 3,371.71 876,643.54

300 x 20 OCR mm over the formed grid having fire rating of 60 minutes as per BS 47G / 23 of 1987. Light Reflection of > 85%. Noise

Reduction Coefficient (NRC) of 0.70, Sound Attenuation of 32 db, K = 0.52-0.57 W/mk. Humidity Resistance up to 99% at 50’C. The

grid to be used is Silhoutte type as per approval of the Engineer-in charge

TOTAL FALSE CEILING WORKS

3 WALL FINISHES WORKS

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs

3.02 9.1 or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Second class teak wood

Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plug

3.03 8.27 etc. including priming coat complete.

8.27.1 Kiln seasoned and chemically treated hollock wood 1.00 cu m 163814.10 163814.10

2 Digitally signed by AMIT

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with

frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces

9.21.1 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws 10.00 Sqm 2015.75 20157.50

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door

3.05 9.23 shutter to be measured). 10.00 Sqm 401.40 4014.00

Providing and Fixing Glass Door Handle-22X922 mm Dtype Handle Material : Stainless Steel. Finish : Satin Stainless Steel (SSS). of

approved make and model all complete as per the direction of Engineer-in-charge.

For 10 / 12 mm Glass.

Material : Stainless Steel.

Finish : Satin Stainless Steel (SSS).

Providing and FixingMortise Lock Premium SS Mortise Lock Body SB/TB for door thickness 25-50 mm for wooden doors of approved make

and model all complete as per the direction of Engineer-in-charge.

3.07 MR Door thickness : 25mm to 50mm 4.00 Each 895.62 3582.47

Finish : Satin Stainless Steel (SSS), Bright Chrome Plated (CP)

Providing 40x5mm flat iron hold fast 400mm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in

3.09 9.53 cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). 10.00 Each 194.35 1943.50

Providing and Fixing Top Pivot-001,002 top and Bottom Strap for wooden doors of approved make and model all complete as per the direction

3.10 MR of Engineer-in-charge. 2.00 Each 1009.61 2019.21

Providing and Fixing Dead lock Back set- 50 mm with Key Hole for wooden doors of approved make and model all complete as per the

3.11 MR direction of Engineer-in-charge. 2.00 Each 850.83 1701.67

Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce Sand-blasting effect on glass

with customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8)with adhesive having minimum tensile strength of 3.5

pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass

3.15 MR Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors). Contractors payment wouldn't be released until & unless 20.00 Sqm 2467.00 49339.93

he/she produces orginal warranty certificate from the manufacturer.

Providing and fixing Bollard Channelled woodwork acoustic wall panel of width of 192/132/128mm with finishing of 15 mm thick Grooved

wooden acoustic panel of size 2420 mm, Groove Size 3.2mm at an interval of 21mm/28 mm c/c as per acoustic design / Architects’ approval,

the wooden acoustic panels to be backed with black acoustic fleece with NRC of 0.45 (NRC 0.8 with 50mm GW of 48kg/m3).the edge of panel

3.16 MR shall be Tounge and groov to be fixed with clips on aluminium profile designed specially fo the panel. the panel will be mounted with the help of 0.00 Sqm 3858.44 0.00

clips on Bollard Aluminium extruded Keel. The grooved acoustic panel laminated in desired shade as per Engineer In charge / Architect’s

Providing and fixing of 6 mm thick premium GRIHA rated Lacquered glass of approved color by Architect/ Client / Customer, fixed with

compatible neutral grade silicon on a perfectly levelled 12mm thick water proof marine plywood / MDF / Mineral fibre board which is mounted on

RCC wall/any other structure. Lacquered glass must be made industrially (using curtain coating process); opaque (if viewed against a support

wall), uniformly coated with PU lacquer (50 micron thick coating or more); panel to panel colour consistency (measured by photo spectrometer);

3.17 MR highly durable (passes hardness test for minimum 220 oscillations); humidity resistance (conforms to BS EN 1036 1999 or equivalent) ; 20.00 Sqm 4304.78 86095.63

environmentally friendly having Low VOC (no lead, no arsenic, no copper, no formaldehyde), low VOC content <100g/l. Silicone used should

not react with lacquer coating (compatible neutral cure silicon)

3 Digitally signed by AMIT

Providing & supplying of Window Blinds as per the approved sample in required shade and style consisting, of Roller Blinds comprising of

optima screen Fabric comprising of 22% polyester, 78% PVC, Fabric weight 460-480G weight per sq m, Thickness 0.67 mm, Yarn count 18-

19/cm, having fire resistance standard – NFPA 701-89 small testing ISO-5659-2 .The tear resistance should be complying to ISO4674 &

breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch for quick,easy and safe installation,moulded plastic with steel spring

support and inserted into the tube end. It shall be driven by a ball chain pulley with ball chain and can be positioned at right side or left hand

side of the Shade. The Shade when lowering or raising, shall be automatically locked in position upon release of the ball chain by means of a

built in friction lock.Universal clutch for left and right hand operation.Chain Gear Ratio of 1.75:1.The END PLUG shall be molded of plastic witha

steel location pin. The plug shall be inserted into the tube end. (Opposite to the Drive Unit) for ease of installation. TheSUPPORT BRACKETS

3.22 MR shall be of coated steel & provided with covers and used in right hand or left hand positions differentiated by the acceptance of the of the 25.00 Sqm 2806.00 70150.00

rectangular drive unit support or the round idler plug pin.Can beinstalled (a) On Face (b) Ceiling Mount (c) On Frame (d) in Recess. The Bracket

should be protruding outside maximum of80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm internal diameter & skin

thickness of 1mm and shall incorporate a key way integral with the tube to accommodate the spline. The BOTTOM RAIL shall be a Flat Bottom

made up of powder coated steel. The BALLCHAIN shall be 2mm diameter cord with 4.5mm diameter acetal balls moulded co-axially to it on

6mm pitch to form an endless ballchain.It is used for raising or lowering action of the shades.

PELMET: Fabricate and install pelmet made of 19 mm thick board, up to 300 mm high and in line with external glazing as per details of

3.24 MR Architect. Rate to include finishing exposed surfaces of the Pelmet with enamel paint of approved shade or 1mm laminate. 25.00 RM 1781.74 44543.56

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) 15.00 Sqm 1018.05 15270.75

3.27 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 15.00 Sqm 86.45 1296.75

13.4 12 mm cement plaster of mix :

3.29 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. 160.00 Sqm 214.30 34288.00

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of

approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in

skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey

8.31 cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality

conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick

bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints

with white cement and matching pigments etc., complete.

PRIMER: Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. Water

13.43.1 thinnable cement primer.

ACRYLIC EMULSION PAINT: Painting of wall, ceiling, POP/ plastered, Gyspum etc. surfaces with smooth and even finish velvet touch

3.33 MR paint of approved brand and manufacture to give an even shade. Two or more coats on new work complete to the satisfaction of 850.00 Sqm 234.79 199,569.52

the Engineer- in -charge complete with the preparation of the base etc.

4 Digitally signed by AMIT

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on

MR wooden /steel frame work, complete as per direction of Engineer-in-Charge

12 mm HDHMR Borad 180.00 Sqm 1380.00 248400.00

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on

wooden /steel frame work, complete as per direction of Engineer-in-Charge

4mm thick MDF Board 180.00 Sqm 273.00 49140.00

Providing and fixing metal system up to ceiling height, which includes frame work made of special section power pressed/ roll form G.I. sheet

with zinc coating of 120 GSM, consisting of Boral U track 52mm wide having equal flanges of 30mm and 0.55mm thick (Base metal thickness)

fastened to the floor slab and ceiling soffit using rawl plugs with screw at 600mm centers, with first & last fixing point at not greater than 50 mm

3.36 MR from either end. Boral C studs 50mm wide having one flange of 34mm, other flange 36mm, lip size 6 mm and 0.55mm thick installed 180.00 Sqm 1022.00 183959.69

perpendicularly within the flanges of floor and ceiling channels located directly opposite to each other at not more than 610mm centers.

Maintain 5 to 10mm gap between C Stud and web of U Track.

Providing & Fixing decorative high pressure laminated sheet of plain/ wood grain in gloss/ matt/ suede finish with high density protective

3.37 9.127.1 surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 180.00 Sqm 890.55 160299.00

TOTAL WALL FINISHING WORKS

4 MISCELLANEOUS WORKS

Modular kitchen - Under counter storage cabinets:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and sufficient

number of drawers made of 18 mm thk. ISI Marked comm. ply , all ply to be laminated with 0.8 mm laminate.All shelves should be supported

on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at least

18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters finished in high gloss acrylic of approved.

The cabinet boxes of floor units will be supported by 100mm height vertical adjustable legs which will be covered with PVC skirting in brushed

4.01 MR aluminum finish attached by hardware of skirting. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and rawl 5.00 Sqm 7249.00 36245.00

plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be considered for measurement and payment. Cabinet

boxes size would be varies from 400X560X710MM to 1000X560X710MM (approx.) and join together as per site requirements etc.

Modular Kitchen - Overhead storage wall units:

Providing & fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and sufficient

number of drawers made of 18 mm thk. ISI Marked comm. ply. All ply to be laminated with 0.8 mm laminate.All shelves should be supported on

approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at least 18mm

4.02 MR thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters finished in high gloss acrylic of approved. The unit 5.00 Sqm 12165.00 60825.00

shall be fixed to the floor/ wall/slab using metal screws of appropriate size and raw plugs. Only front face area of cabinets and skirting from floor

to top of boxes shall be considered for measurement and payment. Cabinet boxes size would be varies from 400X560X710MM to

1000X560X710MM (approx.) and join together as per site requirements etc.

Providing and fixing of Innotech with metal sides and quadro channels

4.02B MR Providing and fixing baskets 5.00 Each 4012.65 20063.23

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting

of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended

proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse

sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii)

4.03 22.3 IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. 20.00 Sqm 774.25 15485.00

(Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

TOTAL MISCELLANEOUS WORKS 15485.00 134875.25

Dismantling, and removing all existing removable items and materials from site and keeptin it away from site as per instruction of Engineer in

5 Digitally signed by AMIT

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR 2021/ QUANTIT

S NO DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

S NO DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

DSR (INR) NON-DSR (INR)

Supply, Installation, Testing and Commisioning of SINGLE LEVER CONCEALED BASIN

MR 1 MIXER (WALL MOUNTED) WITH SPOUT (COMPOSITE ONE PIECE BODY) EACH 4 14614.00 58456.00

Supply, Installation, Testing and Commisioning of TABLE TOP BASIN, SIZE:

Supply, Installation, Testing and Commisioing of suitable compatible WASTE COUPLING

MR 3 32MM- FULL THREAD- WITH CERAMIC CAP-*130MM HEIGHT *65MM CERAMIC CAP EACH 4 2267.00 9068.00

Supply, Installation, Testing and Commisioing of BOTTLE TRAP (WITH INTERNAL

MR 4 PARTITION) 32mm SIZE WITH 300mm & 190mm LONG WALL CONNECTION PIPES & EACH 4 3065.00 12260.00

Supply, Installation, Testing and Commisiong of RIMLESS, BLIND INSTALLATION WALL

MR 5 HUNG WC WITH UF SOFT CLOSE SLIM SEAT COVER, HINGES AND ACCESSORIES EACH 3 13797.00 41391.00

SET, SIZE: 375X520X400 MM

Supply, Installation, Testing and Commisiong of PNEUMATIC CONTROL PLATE

Supply, Installation, Testing and Commisiong of ANGULAR STOP COCK WITH WALL

Supply, Installation, Testing and Commisiong of CONCEALED STOP COCK WITH

ADJUSTABLE WITH WALL FLANGE 15mm

Supply, Installation, Testing and Commisiong of HAND SHOWER (HEALTH FAUCET) WITH

MR 9 8mm DIA 1.2 METER LONG FLEXIBLE TUBE AND WALL HOOK EACH 3 2375.00 7125.00

Supply, Installation, Testing and Commisiong of PNEUMATIC SINGLE PIECE SLIM

CONCEALED CISTERN BODY WITH INSTALLATION KIT & “S-TYPE” DRAIN PIPE

MR 10 CONNECTION SET FOR WALL HUNG WC (WITHOUT FLUSH CONTROL PLATE EACH 3 7381.00 22143.00

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I.

17.10 brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting

11 and making good the walls wherever required :

17.10.1 Kitchen Sink with Drain Board

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings

17.28 complete.

17.28.2 Flexible pipe

Providing and fixing mirror of superior glass (of approved quality) complete with 6 mm thick

hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

17.34 Providing and fixing toilet paper holder

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved

15 quality conforming to IS : 8931

18.53.1 15 mm nominal bore EACH 10 500.35 5003.50

Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast

(spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement: 3 coarse

17.61 sand: 6 graded stone aggregate 12.5 mm nominal size) including necessary plaster and

pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :

18.76 Cutting holes upto 30x30 cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks EACH 3 362.40 1087.20

Making chases upto 7.5 X 7.5 cm in walls including making good and finishing with matching

surface after housing G.I. pipe etc.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing

18.7 the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step

CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.2 20mm nominal outer dia pipes METRE 10 325.10 3251.00

18.7.3 25mm nominal outer dia pipes METRE 10 408.55 4085.50

18.7.4 32mm nominal outer dia pipes METRE 20 500.95 10019.00

18.7.5 40mm nominal outer dia pipes METRE 20 674.35 13487.00

18.7.6 50mm nominal outer dia pipes METRE 20 927.00 18540.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for

hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe

with clamps at 1.00 m spacing.

18.8 This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of

cutting chases and making good the same including testing of joints complete as per

direction of Engineer in Charge.

Concealed work including cutting chases and making good the walls etc.

18.8.1 15mm nominal outer dia pipes METRE 20 441.15 8823.00

18.8.2 20mm nominal outer dia pipes METRE 20 513.75 10275.00

18.8.3 25mm nominal outer dia pipes METRE 10 626.05 6260.50

18.8.4 32mm nominal outer dia pipes METRE 10 712.75 7127.50

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS

21 standards and weighing not less than 690 gms.

Digitally signed by AMIT

18.51.1 15 mm nominal bore EACH 3 708.40 2125.20

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for

soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all

neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or

without doors), reducers, WC connectors, couplers, expansion joints / bellows, cowels,

clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp &

hangers etc. in concealed / inside duct / under floor & basement ceiling / external work etc.

including chase cutting as required, excavation and back filling in all kind of soils, suspended

from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm.

alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

22.0 nominal size) including cost of shuttering for proper completion of the work, breaking and

making good the walls and floors etc. after pipes have been duly laid and tested. The rubber

MR ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on

50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes

commissioning of all pipes lines as per drawings and specifications and as directed by engg-

in-charge at site.

a 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 20.00 536.00 10720.00

b 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 20.00 416.00 8320.00

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6

Kg/ Sqcm rating with fitting for waste pipe from fixtures to floor trap including reduces,

enlarger, socket, couplers, bends, tees etc including fixing at wall/ ceiling level supported by

MR 23 clamp & hangers etc. cutting holes in wall/ floors/ slabs and making good the same with

cement concrete 1:2:4 complete as required.

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating

complete in all respects.

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser

Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps.

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round

MR 26 cover with screws and other required fitting complete as required. EACH 6 1001.00 6006.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

DESCRIPTION TOTAL AMOUNT TOTAL AMOUNT

S NO NO UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC conduit,

1.10 with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent

switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface

1.55 / recessed PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single

A.3 1.12 core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS Metre 580 334.00 193720.00

PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

box including connections but excluding modular plate etc. as required.

A.5 3 pin 5/6 amp socket outlet

1.24.5 6 pin 15/16 amp socket outlet Each 60 197.00 11820.00

Supplying and fixing modular blanking plate on the existing modular plate & switch box

excluding modular plate as required.

Supplying and fixing following size/module, GI box along with Modular base & cover plate on

existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC

insulated copper conductor, single core cable in surface/ recessed steel conduit as required

1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 200 233.00 46600.00

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 400 275.00 110000.00

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 100 334.00 33400.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 40 439.00 17560.00

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 10 1005.00 10050.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 10 1365.00 13650.00

Supplying and making end termination with brass compression gland and aluminium lugs for

9.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

2.10 breaker suitable for inductive load of following poles in the existing MCB DB complete with

D.2 connections, testing and commissioning etc. as required.

2.10.1 Single pole Each 20 256.00 5120.00

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, vertical type three pole and neutral, sheet steel, MCB

distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral

2.5 bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,

residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in

2.14 the existing MCB DB complete with connections, testing and commissioning etc. as required.

Digitally signed by AMIT

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

Supplying and fixing following modular switch / socket on the existing modular plate & switch

E.7 box including connections but excluding modular plate etc. as required.

1.24.6 Telephone Socket Outlet Set 46 148.00 6808.00

Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper conductor,

1.18 unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required.

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with

MR required suitable number of GI couplers for joining raceways and fixing GI brackets and all

accessories complete in all respect as per the directions of engineer in charge

(a) 300mmx38mm(GI) - 3 compartment Mtr 60 1279.36 76761.51

E.9 (b) 225mmx38mm(GI) - 3 compartment Mtr 20 1027.52 20550.33

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables at

the intersection of raceways supplied completely with base and cover plates, height adjustable

MR junction box 65- 90 mm including all accessories complete in all respect as per the directions

of engineer in charge

Total of Electrical items 922644.00 249162.99

Digitally signed by AMIT

S NO Description UOM Qty Rate DSR Amount Non-DSR Amount

A. UTP Components for Data

1. Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper conductors for

(DSR Connectivity of Hub room to End Point.High Speed Gigabit Ethernet U/UTP, 250 METRE 2000 57.00 114000.00

1.53.1 MHz, Class E, 23 AWG, Unshielded LSZH Cable, C6

2) Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable

termination at Work Station end. Keystone Unshielded Outlet, 180DG C6, Blue

3 Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable

termination at Rack Side end Redantant . Keystone Unshielded Outlet, 180DG C6,

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for

information outlet (I/O) to end user device connectivity.High Speed Gigabit 24AWG Nos. 100 400.00 40000.00

U/UTP Patch Cord Blue, LSZH, C6, 2M

5 Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr (7 feet) for

information outlet (I/O) to end user device connectivity. (Rack end), High Speed Nos. 100 400.00 40000.00

Gigabit 26AWG Traceable Patch Cord Grey, LSZH, C6, 2M

6 Supply , Installtion , Testing and Comissioning of 24 port Loaded Jack Panel for

CAT6 cable termination at rack end. Data Active

Total : A - UTP Components 114000.00 189200.00

B 200 Pair MDF Box

1 200 Pair MDF Box with mounting Frame 1 17500.00 17500.00

2 20 Pair Krone Module 6 2000.00 12000.00

3 25 Pair Riser Cable 35 1253.00 43855.00

Total : B - MDF Box 0 73355.00

GRAND TOTAL A+B 114000.00 262555.00

GRAND TOTAL A+B 114000.00 262555.00

10 Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FURNITURE

S No Item Specifications Qty Offered Price Amount

Providing and placing panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including

powder coated aluminium trims. Tiles: Combination of top tiles are fabric magnetic/fabric/fabric tackable/white board/glass writing

board/ clear glass tile/ plain metal/ prelam tile. Bottom tiles - Plain metal/ fabric magnetic / fabric / laminated /prelam. The panel

thickness comprises of 38mm (35 mm Minimum) thick paper honeycomb + 3mm MDF on each sides + 0.6mm decorative laminate or fabric on

both sides. The uprights and horizontals shall be made of aluminium extrusion having average wall thickness of 1.2 mm & powder coated

with epoxy- polyester powder. Particle board framing is used on outer boundary of these blocks as well as intermediately at certain

locations forming conduit for passing cables. These blocks are located in the mid segment of the panels and can be provided with

Workstations Linear cutouts for mounting switch boxes (above or below the worktops). Top tiles can be offered in variety of combinations. The fins along the depth

1200 x 600 shall be 22.8mm thick. Worksurface- out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200mm x 600mm x

750H. Brackets shall be made from 2mm thick CRCA steel. Pedestals with legs- pedestal flat metal front, free standing central locking of

size 390 mm w x 435 mm d x 646 mm height 3dr = 2box+1file. The work shall be carried out as per the instructions and guidance

received from engineer incharge. The product must be UL Greenguard, BIFMA Level 3 certified.

11 Digitally signed by AMIT

S No Item Specifications Qty Offered Price Amount

1 MR Buy Back Material of old tabels 60 2,500.00 150,000

2 MR Buy Back Material of old Chairs 25 1,000.00 25,000

Digitally signed by AMIT