138WE/L-67/2019-20

Amount

Precast cement concrete block, M-10(1:3:6), type C-1, (using 20mm graded crushed stone aggregate) masonry with solid blocks exceeding 10 Cm in width and setting in mortar 1:4, complete all as specified and directed.

PCC 1:2:4 (nominal mix) type B-1 (using 20mm graded crushed stone aggregates) as in surface channel and drains complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering, complete all as specified.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of precast block work or stonework built in cement mortar including all quoins, arches pillars etc but excluding ashlar facings ,dressed stonework and precast concrete articles and stacking the serviceable materials within 100m and disposal of unserviceable material, debris and rubbish to a distance exceeding 250m but not exceeding 500m complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance exceeding 250m but not exc. 500m complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and directed

Surface excavation (not exceeding) 30 cm deep and averaging 15cm deep and getting out as in hard and dense soil, complete all as specified and as directed.

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out, hard and dense soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25Cm, complete all as specified and directed.

Removing excavated materials/ soils, not exceeding 50mtrs and depositing where directed at a level not exceeding 1.50mtrs, complete all as specified and directed.

Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate), as in filling and mass concrete in foundation, complete all as specified and directed.

Walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6, complete all as specified and as directed.

All as per srl item no 14.00 above but except stone.

PCC 1:3:6 (nominal mix) type C-2 (using 40mm graded crushed stone aggregates) as in surface channel and drains complete all as specified and directed.

40 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded crushed stone aggregates) as in top bed of drain, surface finished even and smooth without using extra cement complete all as specified and directed.

Hard core of broken stone or boulders of gauge not exc 63 mm deposited ,spread and leveled in layer not exc 15 cm thick complete all as specified and directed.

75mm thick Plain cement concrete (1:4:8), type D-2 (using 40mm graded crushed stone aggregate), as sub base of floor or paving, complete all as specified and as directed.

100 mm thick PCC 1:2:4 type B-2 (using 40mm graded crushed stone aggregates) as in floor finish, surface finished even and smooth complete all as specified and directed.

Glass dividing strips 3 mm thick and width 38 mm inserted in position to conform to design complete all as specified and directed .

25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in floor finish, surface finished even and fair to receive top finish complete all as specified and directed.

Non skid ceramic coloured tiles 10mm thick (square/rectangular) , area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as directed by EIC, as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tiles over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. Shade/Colour of tile shall be approved by the GE.

Machine cut kota stone slab flooring 20-25mm thick,over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing / grinding & mirror finish polishing over and including 20 mm thick screed base in cement mortar 1:6 over and complete all as specified and directed.

Machine cut kota stone slab 20 to 25mm thick, as in riser of steps, skirting, dado and pillar etc.; bedded and jointed with grey cement and pointed with white cement with admixture of pigment to match the shade of stone including rubbing / grinding & mirror finish polishing and including 15 mm thick cement screed in cement mortar 1:4 complete all as specified and directed.

RCC M-30, design mix, using 20mm graded crushed stone aggregateas in foundations, including rafts, footings foundation beams, plinth beams and like complete all as specified and directed.

RCC M-30, design mix, using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified.

Use and waste of form work to sides of concrete foundations, footings, bases of Columns, raft and raft beams, sides and Soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished of concrete., complete all as specified & directed.

Use and waste of form work to sides and soffiits of floor or roof beams, beams haunchings, girders, bressummers, lintels, cantilevers, shelves incl. supports, overhangs, etc also splays between floors and beams etc. complete all as specified & directed.

Plain cement concrete M-15 (1:2:4), type B-1, (using 20mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates,water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed , including necessary form work, complete all as specified and as directed.

Pressed steel frame using 1.25 mm thick PBI sheet (size of frame 165 x 60 mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock/ strike plate etc and filling with PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in back of chowkats complete all as specified.

Steel Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed.

30 mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

Sheet glass, 3 mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded Section, size 150mm long and fixed, complete all as specified and as directed.

Aluminium alloy, anodised, sliding door bolt, size 250mm, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed.

Extruded aluminium alloy handles, fabricated type, Anodised, size 150mm, complete all as specified and as directed.

100 mm long mild steel butt hinges, medium weight, cold rolled and fixed, complete all as specified and directed.

Rendering 15 mm thick, on fair faces of brick or concrete surfaces, in cement mortar 1:6 rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

Rendering 15 mm thick, on fair faces of brick or concrete surfaces, in cement mortar 1:4 rendering is to be finished even and smooth (without using extra cement), complete all as specified and as directed.

Preparation of new plastered or unplastered surfaces of wall and applying two coats of oil emulsion distemper, white or tinted, complete all as specified and as directed.

Preparation of new plastered or unplastered surfaces of wall and applying three coats of white washing, complete all as specified and as directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of cement based paint over one coat primer, complete all as specified and as directed by Engineer-In-Charge.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

0.63 mm thick CGI sheeting with nominal grade of zinc coating 120 gms per sqm with two corrugation side lap fixed with 'J' or 'L ' hooks as in roof covering,walls etc complete all as specified and directed.

All as per srl item no 50.00 but except sheet with two corrugation side lap fixed with 'J' or 'L ' hooks as in roof covering, walls etc complete all as specified and directed.

0.80 mm thick plain, galvanised, mild steel sheeting as in ridges, hipe, valley gutters, drip and straight flashing (length and girth as fixed) with grade of zinc coating 120 gms per sqm complete all as specified and directed.

Preparation of wooden surfaces of any description and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of old painted steel surface of any description and applying two coats of synthetic enamel paint all as specified and directed.

Preparing zinc or galvanised surfaces to receive painting by coating with mordant or approved solution including washing and cleaning etc;and applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces of any description, not other wise described over 10 cm width or girth complete.

Steel work in tubular trusses including special shaped washer etc, complete using ERW or induction butt welded tubes, conforming to IS-1161-1979 grade St-240 including one shop coat of red oxide primer complete all as specified and as directed.

Rolled mild sectins as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe-290 Gde E-165 all as specified and directed.

Mild steel works as in Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts . posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Framed work such as grills, gratings etc with ends of bars shouldered and/or riveted or forged into spikes framed guard bars including cutting, drilling, welding etc confirming to Fe-290 Gde E-165 all as specified and directed.

Running welding in repairs exc. 9mm and not exc. 20mm thick of plate complete all as specified and directed.

Point wiring for one light point or fan point controlled by one switch with 1.50 Sqmm, PVC insulated, unsheathed, FRLS single core, multi-stranded, copper conductor cable, 1100 Volts fire resistance ISI, drawn in and including PVC casing and capping, fire resistance, ISI marked, fixed surfaces of walls and ceilings, terminated in and including rectangular PVC board for mounting fitting/ switches/ sockets and 1.50 Sqmm, copper conductor, multi-stranded, FRLS as earth continuity wire connected to earth terminal, including making good to disturbed surface as matching to existing descriptions/ specifications, complete all as specified and as directed.

Description all as per serial item No- 61.00 above but for one 5 Amps socket outlet on independent board, complete all as specified and as directed.

Description all as per serial item No- 61.00 above but for one 5 Amps socket outlet on same board, complete all as specified and as directed.

Point wiring for 3-pin, 15 Amps, socket outlet on independent board with 4.0 Sqmm, PVC insulated, unsheathed, FRLS single core, multi-stranded, copper conductor cable, 1100 Volts, drawn in and including PVC casing and capping, fire resistance, ISI marked, fixed surfaces of walls and ceilings, terminated in and including rectangular PVC board for mounting fitting/ switches/ sockets and 2.50 Sqmm, copper conductor, multi-stranded, FRLS as earth continuity wire connected to earth terminal, including making good to disturbed surface as matching to existing descriptions/ specifications, complete all as specified and as directed.

Modular switch 1 way 6A, 1 module complete all as specified and as directed.

Modular switch 1 way 16A, 1 module complete all as specified and as directed.

Modular Socket, 6A - 2/3 pin combined 2 module, complete all as specified and as directed.

Modular Socket 6A/16A - 2/3 pin combined 2 module, complete all as specified and as directed.

Metal flush box 8 module complete all as specified and as directed.

Metal flush box 6 module complete all as specified and as directed.

Metal flush box 3 module complete all as specified and as directed.

Metal flush box 1 module complete all as specified and as directed.

White cover plate frame (inner plate) 3 module complete all as specified and as directed.

White cover plate frame (inner plate) 8 module complete all as specified and as directed.

White cover plate frame (inner plate) 6 module complete all as specified and as directed.

White cover plate frame (inner plate) 1 module complete all as specified and as directed.

LED bulk head light fitting 1 x 10 watt , 230 volts, attractive wall/ ceiling mounted any type with white reflactor complete with all accessories prewired and includeing connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed. Make: Havells cat part No LHEOAOP7UZ6W010 or equivalent in Bajaj/ Crompton Greaves/ Philips/ Wipro/GE.

LED tube light fitting 22W ,6000K, wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver with all accessories including LED tube complete all as specified and as directed. Make: Havells cat part No- LHEWEBP7PL1W022 or equivalent in Bajaj/ Crompton Greaves/ Philips/ Wipro/GE.

1100 volt grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and over all PVC sheathed of size 16 Sqmm , two single core,flat or circular in service connection suspended by insulating hangers not more than 1 metre apart including 4 mm dia GI suspension wire all as specified and directed.

Sheet metal enclosures for distribution box for MCBs, Single pole and neutral, 8 way with, 240 Volts, double door, with 200 Amps rated bus bar blank plate complete all as specified and directed.

MCB, single pole and neutral, 32 Amps, 240 Volts , 10 KA C series, complete all as specified and directed.

MCB, single pole, 6 to 40 Amps, 240 Volts, 10 KA C series, complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 600x600x6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of earth plate not less than 1.5mtr below normal ground level, connected with galvanized iron wire 4.0mm dia as earth lead means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 15 mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15, type B-1 in pit with precast RCC M-15(1:2:4), type B-1(using 20mm graded crushed stone aggregates) in cover reinforced with XPM not less than 4.0 Kg per Sqm, test point etc. all as shown in electric plate No-3 of SSR Part-I (2009), complete with necessary earth work in any type of soil, removal to a distance not exceeding 50mtr, including testing on completion, complete all as specified and as directed. Note: The cost of excavation and earth work, PCC pit and pit covers, funnel and watering pipe, wire mesh, charcoal dust and common salt, 15mm dia, medium grade, GI pipe as protection to earth lead and earth lead as 4.0mm dia GI wire (main earthing lead from earth electrode to test point length not less than 7.5mtrs) shall be deemed included in the unit rate for earthing.

HILL AND CO.

Mehar Enterprises

neelam construction co

R B TRADERS

M/s Koul & Sons

BETONG BUILDERS