SPECIAL REPAIR TO BLDG NO. HT-02 AND HT-04 BHARATPUR LINES DHARAMSHALA UNDER GE PALAMPUR

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Demolition of cement concrete (reinforced) exc 15 cm thickness but above ground floors complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

Demolition of brick work or stonework or precast concrete articles and precast concrete block walling ,built in cement mortar including all quoins, arches pillars etc but excluding ashlar facings ,dressed stonework and precast concrete articles and stacking the serviceable materials within 100m and disposal of unserviceable material, debris not exceeding 100m complete all as specified and directed.

Taking down cement plaster including backing etc from brick/stone walls / concrete surfaces including raking out joints, hacking for key , scrubbing down with water etc and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m, complete all as specified.

Taking down chowkats with shutters (without taking off shutters from chowkat) not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from chowkat) exc 1.50 Sqm but not exc 4.00 Sqm each complete all as specified and directed. .

Dismantling timber in scantling 40 sqcm and over in section, unframed work complete all as specified and directed.

Dismantling timber in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, unframed work complete all as specified and directed.

Taking down steel water tubing 15 mm bore including all fitting and connections complete all as specified and directed.

Taking down steel water tubing 20 mm bore including all fitting and connections complete all as specified and directed.

Dismantling plain or corrugated steel sheets any gauge thickness including Nanital or similar pattern roof covering including ridges complete all as specified and directed.

Demolition of wall and ceiling boards any thickness including cover fillets complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises complete all as specified.

Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 mtr in depth and getting out in hard/dense soil, complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers n. exc 25cm, all as specified.

Removal of excavated material to be distance n.exc 50 metres and depositing where directed at a level n.exc 1.5 metres high from the starting point, all as specified.

PCC 1:3:6 (nominal mix) type C-2 (using 40mm graded crushed stone aggregates) as in foundation filling and mass concrete complete all as specified and directed.

Plain cement concrete 1:2:4 ( nominal mix ) type B-1 (using 20 mm graded crushed stone aggregates) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork where required complete all as specified and directed.

RCC Type B-1, 1:2:4 (20mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Precast cement concrete as in landing, cover slabs (for manhole etc) and similar articles with precast cement concrete Type B-1, 1:2:4 (20mm graded crushed stone aggregate) and setting in cement mortar 1:4 complete all as directed.

Use & waste of form work to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc alo splays between floors and beams for rough finished surfaces of concrete, complete all as specified & directed.

Use & waste of form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for rough finished surfaces of concrete, complete all as specified & directed.

Brick work with old size fly ash bricks, class 7.5, straight or curved on plan exc. 6 metre mean radius built in cement mortar 1:6 (01 cement : 06 coarse sand) all as specified & directed.

Brick work with old size fly ash bricks, class 7.5, as in half brick thick wall ,any radius, built in cement mortar 1:4 and pointed with same mortar as the work proceeds complete all as specified and directed.

Walling of random rubble stone masonry brought upto course well bonded bedded and soilidly hearted built in CM 1:6, complete all as specified and directed.

Walling of random rubble stone masonry brought upto course well bonded bedded and soilidly hearted built in CM 1:4, complete all as specified and directed.

All as per item 26 above but except stone

Extra over stone walling of granite, trap or basalt stone for hammer dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses with maximum depression on face from straight edge held against the dressed surface n exc 20mm, complete all as specified & directed.

Anodised aluminium frame powder coated for doors, windows, ventilators with one or more rebates including joining cleat for fixing of glass, particle board,aluminium frame etc complete all as specified and directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 160 of MES SSR 2010 Part-II

Anodised aluminium door shutters powder coated, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, door stopper , aluminium anodised sliding door bolt 250mm long one on each door, 150mm long aluminium tower bolt in each panel , anodised aluminum snap beading screws etc. complete all as specified.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails.M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Pane of 4 mm thick sheet glass to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (900 ), and joined together with solvent cement, suppling & fixing in the frame at site, complete as shown on page No 176 to 183 of MES SSR 2020 Part-II compete all as specified and directed.

2nd class hard wood, clean sawn timber, framed and fixed as in scantling complete all as specified and directed.

All as per item 33 above but except timber

Aluminium (die cast) body ,door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg ,complete all as specified and directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Sheet glass, 4mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane including Solar control film 25 micron reflective type (gareware sun control or equivalent)complete all as specified and directed.

Drapery rod , stainless steel of size 25mm bore, including fixing brackets on both sides, corner bulb knobs , stops, rollers etc. complete all as specified

Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame with fillets of width 35mm as per specifications and drawing, complete all as specified.

GI frame work for snap grid ceiling (size 600mmx600mm) made out of angle section 22 x22mm on perimeter walls and tee section 22x22mm web made to shape out of GI Sheet, bottom of section poeder coated, including all arrangements to make o grid of desired size, fixed to walls with nylon sleeves and screws at 450mm centre to centre and suspended work with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long, including Gypsum Board 4mm thick in ceiling fixed with screw as per manufacturers instructions including necessary scaffolding all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

6mm thick PVC Sheet decorative and white colour, for aluminium doors, complete all as specified.

Mild steel work as in wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc., and similar work comforming to Fe-290 Gde E-165 complete as as specified.

Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Plain cement concrete M-10, nominal mix, type C-2, using 40mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in floor finish, surface finished even and fair to receive top finish complete all as specified and directed.

75mm thick PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregates) as in sub base complete all as specified and directed. .

Non-Skid,Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7-8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed. Note : Size,Shade and colour of tiles shall be approved by GE.

Non-Skid,Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7-8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed. Note : Size,Shade and colour of tiles shall be approved by GE.

Non-Skid,Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7-8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 complete all as specified and directed. Note : Size,Shade and Colour of tile shall be approved by the GE.

Glazed ceramic coloured tiles of size 450 mm x 300 mm x 7 mm/350 mm x 250 mm x 7 mm / 1200x600x7mm thick as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 complete all as specified and directed. Note : Size,Shade and Colour of tile shall be approved by the GE.

20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 15 mm thick screed base in cement mortar 1:6 over and complete all as specified and directed.

20 mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 10 mm thick rendering in CM 1:3 incl dismantling of old finishes complete all as specified and directed.

Chequered cement concrete coloured tiles, homogenious texture glossy finished , chemically coated machine pressed 30 cm x 30cm x 25mm thick set, jointed and pointed in near cement slurry in floor with grey cement and pigment and including 15 mm thick cement screed in cement mortar 1:4 complete all as specified and directed. Shade/Colour of tile shall be approved by the GE

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, mixed with water proofing admixture as per manufacturer's instructions, trowelled to even and smooth finish without using extra cement complete all as specified. (Note:- WPC will be measured and paid separately)

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, trowelled to even and smooth finish without using extra cement complete all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on stone masonry or surface other than fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 10mm thick in cement mortar 1:6 (1 cement : 6 coarse sand) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, all as specified.

Keyed pointing to random or polygonal rubble, uncoursed or brought upto course, in cement mortar 1:4, complete all as specified.

Preparation of new steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of new wooden surfaces of any description, not otherwise described, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over and including 2mm thick wall care putty (applied in two layers), finished smooth with sand paper complete all as specified and directed.

Preparation of newly plastered or un plastered, previously undecorated wall surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

Galvanised steel tubing, 15 mm dia, medium grade, with all fittings & fixtures complete, fixed to wall and ceiling or laid in floor and testing on completion all as specified and directed.

Galvanised steel tubing, 20 mm dia, medium grade, with all fittings & fixtures complete, fixed to wall and ceiling or laid in floor and testing on completion all as specified and directed.

15mm bore, brass ,chromium plated, mixer for mixing hot and cold water, screwed down , complete all as specified.

Chromium plated soap dish, any type, fixed to plugs with chromium plated screws complete all as specified.

Toilet paper holder with flat recessed type stainless steel complete all as specified.

Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Wash basins, Vitreous China (Flat white type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, complete all as specified. Make: Cat Part No. 1008 of Cera or equivalent in makes mentioned in Appx 'C'

Stop valves/ angle valve , cast copper alloy, chromium plated, fancy type, screwed down, high pressure , screwed both ends for 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified.

Stop valves/ angle valve , cast copper alloy, screwed down, high pressure , screwed both ends for 20mm bore iron pipe or for unions and fixed in repairs complete, all as specified.

Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified.

Two Way bib cock with single handle and wall flange, cast copper alloy ,chromium plated, screwed for iron pipe or for brass ferrule of 15 mm bore, fixed in repair complete all as specified and directed. Make : Cera Cat Part No. F2014163 or equivalent in makes mentioned in Appx 'C'.

PVC valve less, snow white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, in repairs, all as specified. Make: Cat Part No.B1010112 of Cera or equivalent in makes mentioned in Appx 'C'.

600x450 mm bevelled edge mirror of slected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screwed and cup washers.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, fixed in repair , complete all as specified.

Vitreous China wash down water closet (pedestal pattern), white including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC white seat cover and chromium plated jet including PVC connection, fixed complete including demolition of old unservicable WC and provision of plain cement concrete M-15, type B-I, using 20mm graded crushed stone aggregate, fixed in repairs all as specified. Make: Cat Part No. 2008 for EWC, 2308 for seat cover, 2201/B for internal fittings of 'Cera' or equivalent in makes mentioned in Appx 'C'

PVC connections 15 mm size with PTMT nuts of length 450mm fixed in repair complete all as specified and directed.

110mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to trenches or in floor ,fixed in repair omplete all as specified and directed.

110mm dia PVC(SWR) pipe having pressure rating 4Kg/ Sqcm, fixed in retaing wall weep holes complete all as specified and directed.

75mm dia PVC(SWR) pipe single socketed with rubber ring joints, laid/fixed to trenches or in floor , fixed in repair complete all as specified and directed.

110 mm dia PVC(SWR) bend, any radius complete all as specified and directed.

75 mm dia PVC(SWR) bend, any radius complete all as specified and directed.

75 mm dia PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

110mm bore PVC (SWR) 'P’ trap, fixed with solvent cement , complete all as specified.

110mm dia PVC (SWR) junction single, (single T) equal or unequal complete all as specified and directed.

PVC (SWR) reducers 110/75mm, complete all as specified and directed.

75mm dia PVC(SWR) vent cowl complete all as specified and directed.

Concrete bed to drain pipe of 110 mm bore including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) complete all as specified and directed. Note :- Thickness of bed and width of bed shall be provided all as per preamble a (i) & a (ii) on Srl page no 391 of SSR Part-II Rates (2020).

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required, for 100mm bore of pipe, complete all as specified.

Rotational moulded polyethylene water storage tank 1000 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including taking down old tank any typecomplete all as specified.

Taking down point wiring with aluminium/ copper conductor for light point, socket point/ power point etc. in PVC casing and caping, surface pvc/ steel conduits, wood batten with clips including taking down board any type and size complete with any type of switches, sockets, holders, (batten or pendent type), ceiling rose etc. The light fittings (any type), main switches, distribution board with MCB’s of any capacity and make are to be removed/ replaced if required and all as specified and directed. NOTE: - Existing fan regulator any type (Where required) and electric meters are to be refixed and connected properly where required.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multistrand) PVC insulated ISI Marked unsheathed cable in and including PVC concealed (concealed wiring) conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marking, medium grade, ISI marked with all fittings/ accessories as specified in preamble 1 (a) to (q) of Section 19 of SSR Part-II, under heading point wiring, cutting chases, making good in cement mortar in CM (1:3), finishing surfaces to match with existing and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as earth wire (green colour) connected to common earth dolly for modular fitting, modular box sunk for mounting of switches, sockets, fan regulators, light fittings etc. for one light point or one fan point through regulator or one bell point, controlled by one way switch/ push button complete all as specified and directed.

All as per serial item No '97' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.

All as per serial item No '97' above, but for one 3 pin 5 Amps socket outlet, independent all as specified and directed.

All as per serial item No. '97' above but for 3 pin 15 Amps socket out let independent with 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Modular switch 1 way 6A, 1 module, complete all as specified.

Modular Bell push 6A 1 module, complete all as specified.

Modular switch 1 way 16A, 1 module, complete all as specified.

Modular Socket, 6A - 2/3 pin combined 2 module, complete all as specified.

Modular Socket 6A/16A - 2/3 pin combined , 2 module, all as specified and directed.

Modular , White cover plate with frame, 3 module, complete all as specified.

Modular , White cover plate with frame, 6 module, complete all as specified.

Modular, Metal flush box 3 module, complete all as specified.

Modular, Metal flush box 6 module, complete all as specified.

Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified.

Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings including Invertor type LED Lamp , 9 watt, 6500K, Complete all as specified.

Bell, AC, 230 volts, single pole, all as specified.

Sheet metal enclosures for DBs when MCBs to be used, triple pole and neutral, 4 way, double door, 415 volts with 200 Amp rated bus bar completed all as specified.

Decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack , 10 watt LED,6500k, two feet long, with all acessoreis internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable tube light all as specified and directed. Make: Havell's Cat Part No. LHEXACP7IN1W010 of "Havells" or equivalent in makes mentioned in Appendix

LED type tube light, 1x20 watt 230 volts wall mounted Inverter LED batten with square profile and polycarbonate channel. Lithium Ion battery with charging time 8hours-10 hours and back up time upto 4 hours, internely pre wired and including connecting up with three core twisted flexible copper conductor cable of suitable size. Make: Havells cat part No. LHEXACP7FN1W020 or equivalent in Appx

Decorative wall mounted brushed nickle finish fixture opal glass diffuser sutaible with 9 Watt LED lamp B22 Base connector block etc complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable light all as specified and directed Make: Havells cat part No. LHFOAJE1TZ1I060 or equivalent in Appx

Decorative, wall mounting fixture, in durable plastic body & designer mesh in gold finish including 9 Watt LED lamp including connecting up with three core twisted flexible copper conductor cable with suitable size including dismantling of unserviceable light all as specified and directed. Make: Havells cat part No. LHFOECE1TZ1B014 or equivalent in Appx

40 Watt, New generation, IP 65 LED post-top family, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LEDs as light source. Clear Cover offers bright illumination for different applications, fixed in poistion , complete all as specified. Havells cat part No. RUBYPT40WLED757PSYMTOPC or equivalent in Appx

25Watt New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. connecting with PVC insulated three core flexible copper conductor of suitable size from ceiling rose to fitting including bracket made up og 32mm dia GI pipe light grade 1.5 metre long and bent to shape required, complete all as specified Make: Havells cat part No. ENDURASUNDOWNSL25WLED765PASYBOPCIHD or equivalent in Appx

LED Luminaire 600mmx600mm, 36 watt, 6500K, Ultra modern recess mounting luminaire with high performance LEDs, suitable for mounting with Armstrong/Grid ceiling, complete all as specified Make: Havells cat part No. LHEBAEP7IW1W036 or equivalent in Appx

MCB SP 6 to 32 Amp, 240 Volts, C series , 10 KA all as specified.

MCB TPN, 63 Amp, 415 Volts, B series , 10 KA all as specified.

Taking down, keeping in safe custody and refixing exhaust fan and connecting up including provision of cable ceiling rose/connector to fan, complete all as specified.

Taking down, keeping in safe custody and re-fixing electric water heater, storage type any type 25 litre, all as specified and directed.

Taking down, keeping in safe custody and re-fixing and connecting the existing serviceable energy meter, single phase, all as specified and directed.

Sand cushioning to under ground cables provided with a layer of sand 8 cms thick before laying the cable and 15 cms thick after laying the cable complete all as specified and directed.

Sub class "B" bricks for covering to cable laid dry flat, with width equal to length of bricks all as specified and directed.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 16 Sqmm, 4 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed.

Mild steel galvanised iron tubing light grade for cable protection as in road crossing, along poles, walls, floors, drain of 40mm size fixed with MS clamps, nuts and bolts required complete all as specified and directed.

Cutting/ grooving on plinth/ wall/ verandah in any condition for laying of cable through pipe and making good the disturbed surface by using cement concrete 1:2:4 type B-0, using 12.50graded crushed stone aggregate as required complete all as directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC M-15, type B-I using 20mm graded crushed stone aggregates with 40mm thick precast cover of size 550 mm X 550 mm X 75 mm of RCC M-15, type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

Deduct Credit Amount as per Schedule of credit as details given on Srl Page No 30 of tender doucments.

Him Builders (BID ID -3279394)

M/S AMAN ENTERPRISES (BID ID -3283701)