SPECIAL REPAIR TO BLDG NO P-258 AT VSN NAGPUR

Amount

B/R Portion

Taking down carefully existing bitumen tar felt including plaster and roughening the surface ,wire brushing , cleaning and washing with water etc. , and removing the rubbish to a distance exceeding exc 1Km & depositing outside the boundary of vayusena nagar where directed .

Ditto all as per item no. 1 above but on vertical surfaces like parapet except brick coba/tilling etc

Material and labour for roof treatment on RCC roof slab complete as mentioned below, all as specified and as directed:- (i) Checking the roof slab by flooding test with water till total elimination of leakage/seepage/ dampness all as specified in SSR Part-I (after ascertaining location of leakage/seepage/ dampness, carrying out treatment vide item No. 6 hereinafter of pressure grouting shall be operated at the required locations). (ii) Brushing surface with neat cement slurry at the rate of 3.00kg of cement per Sqm. (iii) Cleaning the plastered roof surfaces and applying a coat of bitumen primer @ 0.3 kg/sqm on top of dry surface. (iv) Laying APP modified polymeric membrane 3mm thick with non woven polyester core laid and bonded to the sub-strata and over-laps shall be sealed/fused by flame "torch', application method all as per manufacturer's instructions. (v) Applying bitumen base aluminium paint at 0.2kg/Sqm in two coats over APP modified polymer

M & L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate RCC roof slabs to fill undulations to achieve uniform slope complete all as specified and as directed.

Material and labour for grouting in roof through PVC nipples at a spacing of 45 to 60cm C/C including drilling injection points to a depth of 75-100mm, providing 10mm dia PVC nipples and pressure grouting using with and including cement mixed with plasticizing admixture like FOSROC (model CEBEX100) or PIDILITE (model 207 PIDICRET 8AM) @ 225gms/50kg of cement to fill up all capillaries/ voids/ honeycombing areas inside concrete with pressure of 2 to 4 Kg/Sqcm and continued till refusal. After grouting, nozzles to be sealed with the sealing compound/mortar etc, all as per manufacturers instructions and as directed. Note:- After ascertaining the location of leakage/ seepage/dampness under item No.3 here-in-before, this item shall be operated at the required location.

M & L for rendering over roof slab 10 mm thick in CM 1:3 on concrete surfaces mixed with water proofing compound @ 3% by weight of cement and finished surfaces fair and even complete all as specified and as directed. Note: WPC shall be measured and paid separately.

Supply only intergal water proofing compound

M & L for dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed.

S & F PVC insulation panels with EPS stuck to 1mm plain PVC sheet(20 MM thick pvc panel) suitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specification and drawing with Anodised aluminium snap grid frame work for false ceiling and hanger 6 mm dia GI complete all as specified and as directed.

Demolition of concrete in ground floors and paving's n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removal of debries to a distance exceeding 1km complete all as specified and as directed.

M&L for 30 mm thick cement concrete (1:2:4) type B-0 using 12.5 mm graded stone aggregate for flooring complete all as specified and as directed.

M&L Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors (joint free )etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of cement mortar(1:6) 15 mm thick for laying floor finishes complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over and including cement screed bed 20 mm thick in CM (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M &L for grinding and mirror polishing of kota stone flooring complete all as specified and as directed.

M & L for Granite (of any type) work (table rubbed and polished) in , cooking platforms of 20 mm thick and like over and including 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles in vertical surface 350*450*7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including rendering 10 mm thick CM 1:4 on fair faces of brick or concrete surfaces of wall as in backing of skirting and dado complete all as specified and as directed.

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of cement mortar(1:6) 15 mm thick for laying floor finishes complete all as specified and as directed.

M&L Vitrified Ceramic tiles light shade 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of cement mortar(1:6) 15 mm thick for laying floor finishes complete all as specified and as directed.

M&L Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles( dark shade) exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to ma over and including screed bed or bedding layer of cement mortar(1:6) 15 mm thick for laying floor finishes complete all as specified and as directed.

Taking down cement plaster on brick or concrete surfaces on wall/ceilling etc including racking out joint, hacking for key,scrubbing down with water etc complete all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:4 over brick or concrete surfaces, finished even and smooth using water proofing compound @ 3% by weight of cement. Note: WPC shall be measured and paid separately.

Demolition of brick masonry, built in cement mortar and removal of debris from site complete all as specified and as directed.

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed.

M&L for complete removal of existing treatment of walls and applying two coats of oil emulsion distemper after 1 coat of wall care putty complete all as specified and as directed.

M&L for preparing old plastered surfaces of walls and applying one coats of oil emulsion distemper complete all as specified and as directed.

M&L for complete removal of existing treatment of ceiling and applying two coats of oil emulsion distemper after 1 coat of wall care putty complete all as specified and as directed.

M&L for preparing old plastered surfaces of ceiling and applying one coats of oil emulsion distemper complete all as specified and as directed.

M&L for applying one coat of synthetic enemal paint after red oxide zinc chromium primer on steel surfaces of any discription over 10 cm width or girth , not otherwise discribe after preparation of old painted surface of steel & iron work complete all as specified and as directed.

M&L for Cement concrete (1:3:6) in foundations, filling and mass concrete using 40mm graded stone aggregate complete all as specified and as directed.

M&L for cement concrete, in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed of type C1 1:3:6 (20 MM aggregate) complete all as specified and as directed.

Taking down of chowkat with shutter without taking off shutters from the frame exceeding 1.5sqm each but not exceeding 4 sqm complete all as specified and as directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel Squartube with singal side prelam PVC sheet used instead of plain colour PVC sheed & edges will be painted to match with prelam sheet & fixed in position as per manufacturer's instruction complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a glass pane sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour glass pane sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour fully glazed glass pane sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

S&F in repair Door closer (aluminium extruded body)hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

S&F 2nd class hard wood plain ,solid, straight chowkats and frames ,wrought, framed rebated on the solid ,rounded or chamfered, put to geather with glue pinned at joints complete all as specified and as directed.

M&L for Prelaminated particle board of 12 mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

Supply and fixed Aluminium, anodised barrel tower bolts 200mm of extruded section complete all as specified and as directed.

M&L Mild steel sliding door bolt, plate type,stove enamelled black,with bright bolt not liss than 12mm dia with and including a minimum of 6 bolts and nut,four on bolt plate and two on staple plate and fixed 300mm long complete all as specified and as directed.

S&F Hasp and staple of 125mm length, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and as directed.

M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required hooks (stay), heavy, for large gates; hook and pintle hinges large hasps and staples; chains;hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

M&L for cement concrete 1:3:6 (20mm aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

Dismantling existing PVC water tanks of capacity exc 500 litres & n.exc 1000 litres all as directed and removed from site. NOTE:- Dismantled water tank shall become the contractors property as per Sch of credit.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part , approved quality, 1000 Ltrs complete all as specified and as directed.

Taking up or down steel tubing and connections 15mm bore complete all as specified and as directed.

Taking up or down steel tubing and connections 20mm bore complete all as specified and as directed.

S&F tubes `medium grade' galvanised with all fittings and fixed complete to walls and ceiling or laid in floors 15mm bore complete all as specified and as directed.

S&F tubes `medium grade' galvanised with all fittings and fixed complete to walls and ceiling or laid in floors 20 mm bore complete all as specified and as directed.

S&F C.P.Angle cock 15mm bore dia complete all as specified and as directed.

S &F in repair Gun-metal, globe or gate valves 20mm, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repair'20mm stop valve fancy type chromium plated , with long shunk and cup (concealed type ) screwed downhigh presser, with crutch or butterfly handle, screwed both hands for ironpipe or for unions complete all as specified and as directed.

S&F in repiar 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F PVC (SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and as directed.

S&F PVC (SWR) bends of 75 mm dia complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal 75 MM dia complete all as specified and as directed.

S&F PVC(SWR) P trap of 110mm dia complete all as specified and as directed.

S&F in Repair Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in Repair10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and taking down old one complete all as specified and as directed

S & F in repair vitreous china wash basin, white back, size 550 X 400 mm , errecting on existing CI brackets including taking down old one complete all as specified and as directed.

S&F pvc waste pipe sutable for WHB & SINK complete all as specified and as directed.

S & F in repairWaste coupling of PTMT (half or full threaded) . (Minimum weight 32mm45gms/40mm-60 gms) of 32 mm dia bore complete all as specified and as directed.

S&F in repair bib tap15mm, chromium plated fancy type with crutch butterfly handle, screw down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repair pillar tap cast copper alloy fency type,with capastan heads, chromium plated screwed down high pressurewith or with out lettered "HOT" or "COLD" with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

M&L for Straight fair cutting n.exc 10cm width or girth on exposed surface of brick work incl rubbed finish and waste complete all as specified and as directed.

S/F vitreous china wash down water closet pan(pedestal pattern), white excluding fixing bolt flushing cistern and flush pipe complete all as specified and as directed.

S&F CP health faucet including all necessary fitting of 15mm bore complete all as specified and as directed.

S & F in Repair Plastic water closet seat cover, black closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F PVC connection 15mm bore dia 450mm long with PTMT nut complete all as specified and as directed.

M&L for cast iron floor trap 75mm with stainless steel greating including jointing to waste pipe fixed in cement concrete type B-1, 1:2:4. complete all as specified and as directed.

M&L for cast iron Nahani trap 75mm with stainless steel greating including jointing to waste pipe fixed in cement concrete type B-1, 1:2:4. complete all as specified and as directed.

S & F Fof Brass Chromium plated tubular towel rail, 20mm dia, D type 60 cm long between flanges complete all as specified and as directed.

S&F in repair Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed.

S&F in Repair brass CP shower roses of 100 mm dia (Make: JAINKO cat No FSJ-4) with S. S. shower rod square of 15*300mm (cat No SSR-2) complete all as specified and as directed.

S&F jaquar (Model no URS-WHT-132530) urinal with fixing accessories set , size 375*315*620 completed as all specified and as directed by the Engineer-in-charge

S&F jaquar (Model no SNR-STL-51083) Sensotronic mini concealed type flushing valve for urinal complete set installation box 7 fitting completed as all specified and as directed by the Engineer-in-charge

S&f Vitreous china urinal partition white of size 310x700 mm complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

S&F tinted glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane of 4 mm thick complete all as specified and as directed.

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

Taking down aluminium Shutters and refixing including oiling, greasing, tightening, scruewing at of all members of shutters of any description exc 1 sq. m and n exc 2 sq.m each complete all as specified and as directed.

S&F 375mm, ordinary rat tail rod pattern mild steel springs including roller and roller plate complete all as specified and as directed.

M&L preparation of surfaces thoroughly by cleaning, washing and removing dust, dirt, oil and loose particles and applying water proofing liquid Dr. Fixit Pidicrete URP in two coats as per manufacture instruction mix with cement complete all as specified and as directed.

E/M Portion

M & L for sub main wiring (concealed) complete with four single core 6 Sqmm FR PVC insulated unsheathed stranded copper conductor cable drawn through in and including 25 mm dia rigid non-metallic PVC conduit heavy grade and conduit accessories including 6 Sqmm FR PVC insulated unsheated stranded copper earth cable connected to common earth dolly complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface all as specified and directed.. Make of cable : Polycab, Finolex,Havells Note: 5 run of 6 sqmm&one run of PVC conduit shall be measured as single unit Note : Rates are deemed to be included for Taking down carefully sub-main wiring of any description and making good to ther disturbed surfaces to match the existing

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanished steel strip or wire armoured, electric cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 core

M & L for point wiring (concealed) on walls and surface on ceiling complete with FR PVC insulated unsheathed 1100 Volts grade, conforming to IS-694, 1.5 sq mm (nominal area) multi stranded copper conductor cable drawn though in and including non metallic medium grade rigid PVC conduit heavy grade accessories, ISI marked, 19/20 mm dia including all accessories, concealed in walls by cutting chases using machine and making good the disturbed surface, with and including suitable modular boxes ,switch plates of suitable make and 1.5 sq mm copper earth continuity wire connected to earth dolly complete for the following complete all as specified and as directed. Note : Rates are deemed to be included for Taking down carefully any type point wiring (light, fans, socket etc) complete including battens and fittings such as switch, ceiling rose, light fittings, regulators, socket, etc. and making good disturbed surface of wall/floor, etc. complete

One light point controlled by one switch

One fan point controlled by one switch

One exhaust fan point controlled by one switch.

One switch socket outlet modular type 3 pin 6 amp on same board.

All as per item No 3 above but 1.5 sq mm cable size and 1.5 sq mm earth continuity wire for one 3 pin socket outlet, 6 amps on Independent board.

All as per item No 3 above but 2.5 sq mm cable size with 2.5 sq mm earth continuity wire for one 3 pin socket outlet, 16 Amps on independent board.

M & L for point wiring complete with FR PVC insulated unsheathed 1100 volts grade, conforming to IS-694, 4 Sq mm (nominal area) multi stranded copper conductor cable drawn through PVC conduit casing and caping (size of casing and caping as required in ground) including all accessories, fixing in walls/floors/ceilings with 4 Sq mm coppr earth continuity wire connected to earth dolly complete for one 16A Socket on Independent board.

Supply and fix master led tube 4ft 20 W LED Tube Polycarbonate type nominal system lumen output of 2100 lumens and a minimum system efficacy of 100 lm/W. The luminaire shall have a rated system lifetime of 40,000 burning hours at L70.The luminaire should have a color temperature of 6500K and CRI>83. The luminaire shall meet IP20 rating with THD < 10% and PF > 0.95. The total power consumption should not exceed 18W (including driver). Make : Phillips/CG/WIPRO

S & F decorative box type fitting with blue coloured end caps pre wired for LED tube energy of 20 Watt . Make : Phillips/CG/WIPRO

S & F Surface mounting LED Luminaries and 1 x 9 Watt LED fitting with connecting up with copper 3 core flexible cord of minimum size 1.5 Sqmm size complete all as specified and as directed . Make : CG, Phillips, Wipro

S & F 0-4 step, one module, modular type electronic regulator for ceiling fan 1200 mm sweep, 240 volts, 100 Watts humfree single pole, all as specified and as directed. Make : Legrand Cat No. 675531

S & F Switch modular type, single pole one way 6 Amps, 250 volts Ac suitable for modular switch boxes without indicator, all as specified and as directed. Make : Legrand Cat No. 675501

S & F socket modular type single pole one way 6 Amps multistandard 250 volts all as specified and as directed. Make : Legrand Cat No. 675554

M & L for ceiling rose, surface bakelite, 65 x 50 mm, two to three terminals all as specified and as directed. Make : Leader, Anchor

S & F socket modular type 16 Amps, 3 pin combine, 2 module,240 volts all as specified and as directed. Make : Legrand Cat No. 675555

S & F switch modular type 16 Amps,one way with indicator, 1 module,240 volts all as specified and as directed. Make : Legrand Cat No. 675513

S & F tripole pole and earth enclosure with a three pin and earth plug with socket complete with one triple pole MCB (metal Plug & socket DB) for upto 7 ton AC,32A A, FP , 3 module, all as specified and as directed. Make : Legrand Cat No. 607851

S & F sheet metal enclosures for DB's for incorporating MCBs, TPN, 4 way, IP-43 with metal double door with 200 amps rated busbar, 415 volts, as per IS-8623 including taking down the old unserviceable TPN DB, all as specified and as directed. Make : Legrand Cat No 507670, ABB,Seimens. Note : Rates are deemed to be including for Taking down DB/main switch of any size and making good disturbed surface of wall/floor complete

S & F MCB TPN, 63 Amps, breaking capacity 10 KA 'C' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc. Make : Legrand Cat No. 408683, ABB, Seimens

S & F MCB TPN, 32 Amps, breaking capacity 10 KA 'C' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc. Make : Legrand Cat No. 408680, ABB, Seimens

S & F MCB SP 10-32 Amps, breaking capacity 10 KA 'C' curve confirming to IS/IEC 60898-1 2002,integrated label holder, sliding bottom clamp , IP 20 protected terminal, sliding shutters, 240 volts, 50 HZ including making necessary incoming and outgoing electrical connection with suitable size of copper lugs etc. Make : Legrand or equivalent in ABB, Seimens

Supply and fixing High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in trenches, walls, floor of size 40 mm bore for protection of cable, earth strips ete and including short lengths, with all pipe fittings such as ends, elbows, unions, tees, reducing tees, adopters, sockets, plugs, hose clips etc. and fixing to walls etc. complete with saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves and cutting through walls, floors and their making good or laying in trenches and also cutting, screwing and waste complete as required and directed.

Harsh Construction Company