SPECIAL REPAIR / REPLACEMENT OF EXISTING BOUNDARY FENCING WITH CHAIN LINK FENCING ALONGWITH SLOTTED Y ANGLE STRUCTURE WITH BARBED WIRE AT SHO COMPLEX UNDER GE MINNIEBAY,SRI VIJAYA PURAM

Amount

Dismantling fencing wire mesh of any type complete all as specified and as directed by Engineer in charge

Dismantling posts of any description , including taking out embedded portion and making good disturbed ground complete all as manufacturers instruction complete all as specified and as directed by Engineer in charge

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc or for shafts, wells, cesspits, manholes, pier holes,etc not exc 10 sqm on plan and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

M & L for Plain Cement Concrete Type C2 1:3:6 Nominal mix (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

M & L for Reinforced Cement Concrete M-30 design mix concrete (using 20 mm graded stone aggretate) as in foundations incl rafts, footings and mass concrete including formwork complete all as specified and directed by Engineer in charge.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams, and similar work for rough finished flat surfaces complete all as specified and as directed by Engr-in-Charge.

M&L for Mild steel TMT bars 10mm dia and over cut to length, bent to shape required incl cranking, bending, spirally for hooping for columns, hooking end and binding with and incl mild steel wire not less than 0.9mm dia or securing with clip quality confirming to deformed or twisted bars complete all as specified and directed by Engineer-in-Charge.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia, as in stirrups cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing complete all as specified and directed by Engineer-in-Charge.

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point outside MD land or otherwise complete all as specified and directed by Engineer-in-Charge.

M & L for Pre-cast cement concrete block masonry using PCC solid blocks in 1:3:6, Type C-1 using 20mm graded stone aggregates exceeding in width and setting in cement mortar 1:6 complete all as specified and as directed by Engineer in Charge

M & L for rendering 5 mm thick in cement mortar 1:4 over a backing coat of 10mm thick in CM 1:6 (Total 15 mm thick) on concrete or brick masonry surfaces finishing the top surface even and fair without using extra cement complete all as specified and as directed by Engineer in charge

M & L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer in charge

M & L for Mild Steel framed work such as fencing post including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed by Engineer-in-Charge.

M&L PVC coated GI chain link fencing 3.5mm dia with 50mm x 50mm mesh including fixing of MS line wire / rod, flat iron & machine made hexagonal or square head bolts to fencing posts including dismantling of fencing and fencing post complete all as specified and as directed by Engineer-in-Charge. Note :Mild Steel rod,flat iron and bolts will be measured and paid seperately.

Supply only mild steel screw bolts 10mm dia machine made with hexagonal or square head at one end and screwed the other or screwed both ends for fixing of chain link fencing complete all as specified and as directed by Engineer-in-Charge.

Supply only Mild Steel bars for support to chain link fencing complete all as specified and as directed by Engineer-in-Charge.

Supply only Mild Steel Flat iron as in fillets for securing wire mesh including all necessary drilling, bolting or riveting etc and similar work confirming to Fe-410-0 to Fe-310-0 complete all as specified and as directed by Engineer-in-Charge.

M&L for applying two coats of synthetic enamel paint over a coat of Red oxide primer including preparation of new steel/iron surface of any description exc10 cm in width or girth complete all as specified and as directed by Engineer-in-Charge.

M&L for Painting one coats of synthetic enamel paint including preparation of old steel surfaces of any description over 10cm in width or grith not other wise described complete all as specified and as directed by Engineer-in-Charge.

S&F Galvanised, 2 stranded, steel barbed wire 2 mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed Note : Each line of wire shall be measured for payment

S&F Punch tape concertina coil fencing of 600mm dia ,10 m openable length (total length 90m) having 50 nos rounds per 60 m length spring core wire (2.5mm thick) of high tensile strength of 165 kg/sqmm having weight 43.47 gm/m,including necessary wire for fixing coil on security compound wall to y shaped MS angle and fixing with 15mm long,8mm dia ,j hook embedded in PCC 1:2:4 complete all as specified and as directed by Engineer in charge

M&L for forming embankments including raising or lowering earth,spreading in layers n.exc.30 cm thick,watering,ramming/rolling and finishing to required size, shape n.exc 1.50 metre high from base complete all as specified and directed by Engineer in charge.

Material & Labour for providing and fixing stainless steel (Grade SS-316) ISI marked railing dul polished with buffing machine made of hollow tubes, channels, plates etc., including welding, grinding , buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts complete all as specified and directed by Engineer-in-Charge.

ANITA VARMA ENTERPRISES (BID ID -3260853)

Island Agency (BID ID -3261329)

M/s Saina Enterprises (BID ID -3260924)

MAJUMDAR FURNITURE (BID ID -3260982)

M/s Prem Enterprise (BID ID -3260953)

Nirman Construction Company (BID ID -3260873)

M/s Gurunath Construction (BID ID -3261019)