CA NO GE/ND43/202223 SPL REPAIR TO ROOF TREATMENT,WEATHER PROOF PAINT, FLOORING AND MISC CONNECTED WORK TO BLDG NO P63 OF HQ IHQ OF MOD ARMY TPT UNIT ASC UNDER GE NEW DELHI

Amount

Dismantling brick tiles or terracing tiles single layer on roof laid, bedded and pointed in any mortar incl removing the unserviceable material out side the MOD land.

Demolition of Mud phuska in roofs, any thickness incl plastering & leaping plaster

M/L for cutting grooves in brick wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed

M & L for :_ (a) Cleaning the surface , remove dust, dirt , loose particles and unsound substrate and grading with cement mortar (1:4), 10 mm thick, as in slab surfaces, beams, columns, parapet, and junction of walls etc., grading with a slope of 1 in 120 mixed with liquid/integral water proofing compound as per manufacturer's instruction as approved by GE (water proofing compound to be measured separately). (b) Applying evenly a tack coat of water proofing shield primer @ 0.50 Kg / Sqm as a bonding layer over finished plaster surface including cleaning the surface . (c) Over the coat of bitumen bonding layer as above APP modified polymeric membrane (weight not less than 3.0 Kg/Sqm and minimum 3 mm thick reinforced with polyester non wove fabric (weight not less than 150 gms/sqm), unrolled and bonded completely to the substrate with side over lap of 75 mm or end over lap of 100 mm. The overlaps are then sealed/ fused by flam technology method as per manufacture instruction. (d) Sealing edges well into grooves & protect with CM 1:2 complete all as specified and directed. Note:- The work for water proofing treatment on roofs shall be executed through original manufacturer's or their authorised applicator.

M&L providing cement concrete as in roof kerbs, levelling courses for making proper gradient/slope or mud stops rounded or chamfered on edges with B-1 , 1:2:4 using stone aggregate mixed with water proofing compound as per manufacture instruction including necessary form work complete all as specified & directed. (water proofing compound to be measured separately).

Demolition of cement concrete unreinforced of any description and in any position not other wise specifically provided as in drain copings and similar situations incl removing the unserviceable material out side the MOD land complete all as specified & directed.

M&L for PCC 1:3:6,type C-1 (using 20mm graded aggregate) as in water tank platform mixed with water proofing compound as per manufacture instruction as in roof floors. (water proofing compound to be measured separately).

M&L for PCC 1:2:4 type B-1 (using 20mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

Supply only liquid water proofing compound.

Material & labour for cement concrete tiles of size 25 cm x 25 cm x 22 mm thick, machine pressed, set, jointed and pointed in neat cement slurry with grey cement and no pigment in roofs, floors over and including screed bed or bedding layer of cement mortar 15 mm thick in CM 1:6 for laying floor finishes complete all as specified and directed.

M&L providing cement concrete in roof kerbs or mud stops rounded or chamfered on edges, with type B-0, 1:2:4 using 12.5mm stone aggregate complete all as specified & directed incl form work etc.

Providing and fixing rebar of required length & diameter with Sika anchor fix R-3+/Mungo/Fischer FISV 390/Hilti RE-500 Epoxy resign where ever required in RCC members including power drilling, cleaning of holes then rebar shall be inserted in holes that shall be fixed with epoxy to ensure the bond as per manufacturers recommendation complete as per site requirement and direction of Engineer-in-Charge of 100 mm deep(minimum), 16 mm dia hole suitable for inserting 12 mm dia reinforcement bars.

Providing and fixing rebar of required length & diameter with Sika anchor fix R-3+/Mungo/Fischer FISV 390/Hilti RE-500 Epoxy resign where ever required in RCC members including power drilling, cleaning of holes then rebar shall be inserted in holes that shall be fixed with epoxy to ensure the bond as per manufacturers recommendation complete as per site requirement and direction of Engineer-in-Charge of 100 mm deep(Minimum), 12 mm dia hole suitable for inserting 08 mm dia reinforcement bars.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as directed by Engr-in-Charge.

Ditto as per item no 14 above here-in-before but 6 to 8 mm dia

M&L polymer modified cement bonding coat, prepared and applied on the concrete/masonry surface with 1 part of Sika latex with 4 part of water and 6 part of cement by weight. Coverage Sika latex 0.25 kg/sqm for one coat at all heights levels. Adhesive bond strength not less than 2.5 MPa. (Make :- Sika/BASE Fosroc/Dr Sunanda) including chipping of the loose concrete all as directed by Engineer-in-Charge..

Taking down cement plaster from brick or concrete surface incl racking out joints hacking for key and scrubbing down with water complete including removal of rubbish off the premises all as specified.

M&L for premix/ready-mix plaster 15mm thick on brick or concrete surfaces of walls, chajja, balconies, beams , columns, manholes etc and similar work in CM 1:4 finished even & smooth without using extra cement over a coat of UltraTech seal and dry 5 plush as bonding agent including necessary scaffolding, form work, safety precaution up to multi storey of bldgs. complete all as specified & directed.

M&L for two coat of super quality weather proof exterior emulsion paint over & incl one coat of primer from the same manufacturer on external walls / ceiling surfaces after preparation of surface by wall care putty on New surface all as specified by Engineer-in-Charge. Make :- Apex ultima from Asian, Acroguard 3X from Acro Paints or Equivalent in approved makes

Taking up or down 15 mm bore GI tubing and connections including cleaning for re-fixing complete all as specified and directed.

-Ditto- as per item No 20 above here-in-before but for 20mm dia.

S/F GI tubing ,medium grade, galvanised with all fittings fixed complete to walls and ceilings or laid in floors/walls,roofs etc for 15mm bore pipe concealed / open.

-Ditto- as per item No-22 above but for 20mm bore pipe.

M&L for cutting chases on brick or concrete surface for concealed water tubing or girth n.exc 10cm including making good of disturbed surfaces with PCC 1:2:4 type B0 using 12.5 mm graded aggregate complete all as specified and directed.

S&F gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed for 15mm dia pipe (ISI Marked)

-Ditto- as per item No-25 but for 20mm dia pipe.

Dismantling of old PVC water tank of capacity 500 ltrs incl making connection with fitting for inlet & outlet pipe.

As per item No-27 but capacity 1000 ltrs incl making connection with fitting for inlet & outlet pipe.

S&F rotational moulded polythene water storage tanks in double layer (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I of capacity 500 ltrs incl making connection with fitting for inlet & outlet pipe.

As per item no 29 above of capacity 1000 ltrs incl making connection with fitting for inlet & outlet pipe.

As per item no 29 above of capacity 500 ltrs but except water tank incl making connection with fitting for inlet & outlet pipe.

S&F PTMT ball valves high pressure with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 20mm dia.

Taking down eaves gutter & rain water pipes ( any size or pattern), incl. all fitting, heads , shoes, bends, swan necks, incl cleaning for refixing or removal to store.

S&F 110 mm dia PVC (SWR) soil pipe, waste and rain water pipe single socketed in any length with rubber ring jointed, laid in floor or fixed to wall with clamps incl testing, setting and jointing with solvent up to six story bldg. with necessary safety precaution in narrow shaft complete all as specified and directed.

As per item no 34 above here-in-before but 75 mm dia.

S&F PVC (SWR) bends, tee and shoes of any radius of 110 mm bore.

S&F PVC (SWR) bends, tee and shoes of any radius of 75 mm bore.

Demolition of brick work or stone boulder masonry, built in cement mortar including all quoins, arches, pillars, drains, culverts and walls etc but excluding ashlar facings, dressed stone work and pre cast concrete articles, built in cement mortar incl removing the unserviceable material out side the MOD land complete all as specified & directed.

M & L for brick work with sub class B burnt bricks straight or curved on plan exc. 6 meter mean radius built in cement mortar 1:4 as in walls, manhole, septic tank soakage well and similar work etc all as specified and directed.

M&L for GI wire netting .90mm dia and 12mm mesh lathing to wood or metal studding,joist, etc. in walls, ceilings, stanchions,beams,etc. including all laps,cuttings and waste complete all as specified.

Dismantling wrought iron or mild steel work of any description any position not other wise provided for complete all as specified and as directed.

S&F welded steel wire fabric, n.exc 4 Kg weight per sqm, cut to length bent to shape required and fixing with and including annealed mild steel wire not less than 0.90 mm dia or fixing with galvanised steel staples or welding supplied and fixed complete to wood or steel members.

M&L framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, welded or forged into spikes framed guard bars, barred doors & walk ways railings frame work of water tank and similar work up to six story bldg. including necessary safety precaution confirming to Fe-290 Gde -E-165

M&L for two coats of synthetic enamel paint on new steel and iron surfaces over a coat of red oxide primer incl preparation of surfaces over 10 cm width of girth.

S&F, PVC floor trap with Cockroach Proofing CP grating with or without hole including jointing to waste pipes , fixed in cement concrete type B-1 (1:2:4), dia of outlet 75 mm, complete all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) laid bedded and pointed in any mortar and removal of old tiles from premises complete all as specified and directed.

S&F non skid ceramic tiles of approved colour and design 9 to 10 mm thick (Square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed..

S&F non skid ceramic tiles of approved colour and design 9 to 10 mm thick (Square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed..

All as per item Sl No 47 above but as in skirting/dado etc over and including rendering 10 mm thick cement mortar 1:4 complete all as specified.

M&L for Glazed ceramic tiles of approved colour and design in vertical surfaces 300x450x7mm thick including provision of high lighter tiles/boarder and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick rendering in cement mortar 1:4.

M&L for circular cutting or notching and waste on glazed tiles.

S&F in repair water closet vitreous china squatting pan of ORISSA pattern size 580 mm X 440 mm white with integral foot rest incl setting the cast iron trap & pan into cement and sand mortar, provn of lime concrete bedding complete.incl valveless syphonic action type PVC low level flushing cistern with inlet ball valve float & handle incl. brackets of 10 ltrs capacity complete

S&F in repair vitreous china wash basin white flat back size 550 x 400 mm including brass chromium plated waste coupling for WHB with long screwed and shanks and fly nuts, flanged end bedded in red lead and other end fixed, PVC waste pipe, 32mm dia ,med grade, pipe with fittings fixed in wall connected to floor trap for drain out, complete including provision of pair or bracket of angle iron 35x35x6mm duly painted with two coat of synthetic enamel paint over one coat of red oxide zinc chromate primer and embedded one end of bracket in PCC 1:2:4 type B-1 bed blocks and cutting for and pinning in ends of brackets in walls and making good all as specified.

M&L for Brass chromium plated toilet paper holder, fixed to wall with CP brass screws complete.(fixed in repairs)

M&L for Stop valves, cast copper alloy, fancy type chromium plated of size 15mm bore, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete (fixed in repairs) .

S&F PVC connections 15 mm size with PTMT nuts of length 600 mm. (fixed in repairs)

S&F for health faucet Chromium plated brass with 1.0/1.50 m long flexible pipe for WC .(fixed in repairs)

Brass CP mixer (Central hole basin mixer) , for mixing hot & cold water screwed down for iron pipe 15 mm bore complete all as specified and directed. (fixed in repairs)

S&F as in repairs PVC bath room cabinet mirror of size 500 x 400 mm with single side hung shutter incl. single looking mirror with PVC inner shelves of any colour as specified.

M&L for Brass chromium plated soap dish fixed to plugs with chromium plated brass screws complete all as specified and directed.

M&L for Glass self assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.(fixed in repairs)

S&F for toughened corner glass shelf 6mm thick with brass chromium plated guard and fixing arrangements complete of size 300 mm complete all as specified and directed by Engr-in-charge Make: Jaguar Cat No CAN-1173 or equivalent in approved makes

M&L for Brass chromium plated shower rose with swivel joints, 125 mm dia with CP neck including fixing to steel pipe or union 15 mm nominal bore complete all as specified and directed.

S&F for bib taps fancy type chromium plated 15mm bore dia of pipe with crutch or butterfly handle complete all as specified and as directed.

S&F for single level exposed shower mixer with provision of connection to exposed shower pipe (SHA-1211) with connecting legs and wall flange complete as wall mixer for mixing hot and cold water complete all as specified and directed of brass chromium plated of No ARI-39147 all as specified and directed.

Supply and fix , brass chromium plated angle valve long shank with cup suitable for 15mm bore pipe, complete all as specified

S&F brass chromium plated towel rail 20mm dia D type 60cm long between flanges of brass chromium plated all as specified

Taking down chowkhats or frame of any description n.exc 1.5 Sqm each with shutters(without taking off shutters from the frame).

Taking down chowkhats or frame of any description exc 1.5 Sqm but not exc 4 Sqm each with shutters(without taking off shutters from the frame).

M&L 2nd class hardwood plain, solid, straight chowkhats and frames, wrought frames rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

S&F for 35mm thick plain framed, panelled shutter (two panel) 2nd class hard wood with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering both faces. The size of rail and stile as per IS : 1003 (part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F factory made 35mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass gauge etc(without sash bars) edges of framing plain, chamfered or rounded fitted with cut and metered beads for securing glass, etc ; size of members of shutters as specified in SSR part I sec 8,clause 8 .24(a).

S&F powder coated (minimum power coating 50 micron) to aluminium frame / guiding rail for sliding or side hung windows/ventilators frame including jointing cleats,glazing clips and fixing complete with one or more rebates for fixing etc complete all as specified.

S&F powder coated (minimum powder coating 50 micron) to aluminium glazed/gauzed window and ventilators shutters, side hung type( or sliding type) without sash bars, aluminium section weighting 0.55 kg per mtr including necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws including fittings such as peg stays 150mm long (2 Nos) to each leaf, hinges 100mm long (2 Nos) each leaf and suitable handle (1 no.) to each leaf complete all as specified.

S&F Aluminium power coated decorative grill of approved colour with 6.3mm thick aluminium section and 100X100mm openings and anodized aluminium 'U' shape channel frame work around the grill for openable type with necessary fittings and locking arrangement complete all as specified and directed.

M&L treating end of posts , backs of chowkhats etc with tar or coal tar black paint area tarred exc 0.5 sqm each all as specified & directed.

Dismantling timber in fillets, rails posts rafters, purlins etc under 40 sqcm in section in unframed work.

M&L for 2nd class hard wood ,plain fillets square, rectangular or triangular in section exc 13 & n.exc 25 sqcm in section , wrought, secured with nails all as specified and directed.

M&L for 2nd class hard wood ,fillets square, rectangular or triangular in section but bull nosed , splayed , chamfered or rounded on one edge or face exc 3 & n.exc 6 sqcm in section ,wrought, secured with nails all as specified and directed.

Dismantling of existing wooden pelmet box incl curtain rod of any description and size and making good the disturbed surface to match with the existing complete all as specified.

S&F Drapery curtain rods decorative type stainless steel 25mm nominal dia of approved quality including fixing of two number decorative brackets fixed in brick/concrete wall, Two number of finials (lattoo) on both ends of curtain rods ( The length of each curtain rod will be 1.00m to 2.50m long) complete all as directed and specified.

S& F 18/19 mm thick block boards, grade 2 quality, interior grade, decorative type or decorative faced veneered on both faces fixed with screws to timber frame work as in CB shutter, crockery show cases, shelves, partitions and in similar situations with 6 mm thick teak wood lipping all-round incl polishing to lipping and all as per specified and directed.

S&F continuous (piano) hinges, mild steel bright finish or electro galvanised width of flap 40mm,

S&F ball catches with 8 mm dia steel ball, and brass body and striking plate including letting in to, complete.

S&F Cupboards knobs 40 mm dia, fixed with nut, screw and washer of mild steel, bright finish.

S&F hasp and staple of size 100mm, safety type of aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete.

S&F mild steel chromium plated, Harrison rail with fixing bracket complete.

S&F aluminium peg set of 6 peg, 30 to 45 CM long,wixed with pvc rawl plug & steel screw complete all as specified.

S&F stainless steel wire cloth of size 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed tinned tacks or galvanised wire staples .

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty / rubber beading as in aluminium door / window shutter, in square n.exc 0.5 Sqm in each pane.

S&F butt hinges 100 mm long ,stainless steel with mild steel hinge pin , bright polished fixed with steel screw complete

S&F butt hinges 75 mm long ,stainless steel with mild steel hinge pin , bright polished fixed with steel screw complete

S&F aluminium alloy ,anodised, sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clip of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy (ISI marked).

S&F extruded aluminium alloy handles , fabricated type , anodised of size 150 mm. (ISI Marked)

S&F 200 mm size aluminium anodised barrel tower bolt of extruded section & fixed.(ISI Marked)

S&F 100 mm size aluminium anodised barrel tower bolt of extruded section & fixed.(ISI Marked)

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring and fixed of 140 mm overall length of cover plate complete all as specified.

M&L for Solid PVC Door frame of size 50 mm x 95 mm made out of 5 mm single side prelam PVC sheet reinforced with M.S tube supplying and fixing in opening as per specification and drawing.

S&F for factory made solid PVC moulded door shutters (with particle board core), 28 to 30mm thick (Stiles) with 2, 4, or 6 raised panel (as ordered) design with 2mm thick moulded prelam PVC sheet on the front face and 2mm prelam PVC sheet on back face, supply and fixing in frame at site as per the specification and drawing.

M&L for MS flat iron as in hold fast, bands, straps, supports or stays for rain water, ventilating pipes, including bolts, if required hook (stay), heavy, for large gates;hook and pintle hinges large hasps and staples; chains, hand made sliding bolts; clamps; hold fasts; wall ties, hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two-way and three way straps, plate washers and similar small articles conforming to Fe-290Gde-E-165 all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons, vertical surface of walls etc..

M&L for making circular cutting or notching and waste on glazed tiles in vertical surfaces for tiles/granite stones complete all as specified and directed.

M&L for Providing & injecting chemical emulsion for post constructional anti-termite treatment along external wall below conc or masonry apron using chemical emulsion @ 2.25 ltrs per linear meter incl drilling and plugging holes etc in apron.

M&L for Treatment of soil under existing floors using emulsion @ 1 Ltrs per hole, 300 mm apart incl drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors.

Demolition of cement concrete (reinforced) of any position not otherwise specifically provided for and including reinforcement required to facilitate demolition upto and including fourth story and on the roof top/mumty/parapet and removal of debris and rubbish out side MoD land complete all as specified and directed.

M&L cement concrete 1:4:8 type D-2 (40mm graded stone aggregate) as in sub base , and mass concrete complete all as specified.

M&L for 75 mm thick PCC 1:3:6, type C-1 (using 20 mm graded stone aggregate) as in floor etc. finished rough surface without using extra cement complete all as specified.

Cement concrete 40mm thick type B-1, 1:2:4 (using 20mm graded stone aggregate) in floors pavings etc finished even & smooth with out using extra cement.

M&L for 100 mm thick PCC 1:3:6, type C-1 (using 20 mm graded stone aggregate) as in hard standing, paths, floor etc. finished rough surface without using extra cement complete all as specified.

S&F glass dividing strips 3mm thick and 38mm wide inserted in position.

M&L for chequered cement concrete tiles 200x200x25mm/300x300x25mm thick of approved colour and design (Square/ rectangular) as in paths, floors etc set and jointed in neat cement slurry with gray cement and pigment over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type A-1 using 20 mm graded aggregate (nominal mix ) in slabs supported on walls, beams and columns in floor, roofs, canopies, chajja and in shelves and the like.

M&L for Form work to sides and soffits of floor or roof beams, cantilevers, shelves, chajjas incl supports, overhang for rough finished flat surfaces.

M&L brick work with old size subclass B" bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4.

M&L for laying Micro-concrete cement based pre packed single component, chloride free, sulphate free,non shrink, free flow, self compacting, ready to use after mixing water in specified proportion of approved quality. The unit rate shall include the cost of form work for providing micro concrete patch repair as required at site with steel jack system and steel props to support the form work in this application of high strength, dual shrinkage, compensated, micro concrete for placing in nominal thickness of 50 mm to 150 mm for concrete repair. Make:- Sika/BASE Fosroc/Dr Sunanda.

Forming Jambs etc to opening incl cutting toothing and properly bonding in to old work complete new work built in CM 1:4

Cutting holes in bricks walls built in cement mortar or cement lime mortar or stone walls built in lime mortar for inserting hold fasts and making good the dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-I in brick not exc one brick.

M&L for 75mm thick precast cement concrete ,type B-0, 1:2:4 (12.50 mm graded stone aggregate) as in louvres & jallies ( measured solid), set in CM 1:4 ,complete.

M&L for preparation of old distempered surfaces of wall by complete removal of existing treatment from wall surfaces and applying two coats of distemper oil emulsion, white or tinted over one coat of alkali-resistant primer paint and 3mm thick wall care putty all as specified & directed.

M&L for preparation of new plastered wall surfaces and applying two coats of distemper oil emulsion, white or tinted over one coat of primer including 3mm thick wall care putty complete all as specified & directed.

M&L for preparation of old distempered surfaces by complete removal of existing treatment from ceiling surfaces and applying two of distemper oil emulsion, white or tinted over a coat of primer paint compete all as specified & directed.

M&L for preparation of new plastered ceiling surfaces and applying two coats of distemper oil emulsion white/tinted over one coat of primer complete all as specified & directed.

M&L for two coats of synthetic enamel paint on new wooden surfaces over a coat of pink primer incl preparation of surfaces over 10 cm width of girth.

M&L for two coats of synthetic enamel paint on old wooden painted surfaces incl preparation of surfaces over 10 cm width of girth.

M&L for two coats of synthetic enamel paint on new steel and iron surfaces over a coat of red oxide primer incl preparation of surfaces over 10 cm width of girth.

S&F sheet frosted glass and glazing with rubber beading and aluminium beading in squares n exc 0.50 sqm in each pane of 4 mm thick complete all as specified and directed.

M&L red colour granite( of any type) 18-20 mm thick table rubbed and polished as in Floor,cooking platform, and the like machine cut laid over and including 15 mm thick screed bed in CM 1:4, laid and jointed with grey cement slurry and incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade including cutting, making hole of 20 mm dia for gas pipe at suitable location as directed at site and polishing complete.

..Ditto .. All as per item No 128 above but as in vertical surfaces such as dado/skirting laid over and including rendering 10 mm thick in CM 1:4 jointed with grey cement slurry and incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including cutting and polishing complete.

M&L for marble stone work 18 to 20mm thick of any coloured (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar including 15 mm thick screed bed in CM 1:4, laid and jointed with grey cement slurry and incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with granite shade including cutting, making hole of 20 mm dia for gas pipe at suitable location as directed at site and polishing complete.

..Ditto .. All as per item No 130 above but as in vertical surfaces such as dado/skirting laid over and including rendering 10 mm thick in CM 1:4 jointed with grey cement slurry and incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including cutting and polishing complete.

M&L rounding to edges of stone slabs one edge such as steps, cooking platforms and other similar situations complete all as specified.

M/L cement plaster 15mm thick in CM 1:4 on brick or conc surfaces finished even and smooth without using extra cement mixed with by adding permeability reducing polymer Sika Latex @ 400gm/sqm (6%) by weight of cementitious content at time of mixing with water as per manufacturer's recommendations including all levelling the surface, curing etc complete. (water proofing compound to be measured separately).

M &L for providing and applying a bond coat of Sika Latex:Water:cement - 1:4:6 with sika Latex consumption @100gm/sqm on the brick wall surface by brush as per manufacturer's recommendations including curing complete.

Supply of Sika Latex

Expose the first joint of masonry structure at ground level horizontally. The plaster must be knocked off at least 50 cm beyond the visibly penetrated area. Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. Drilling Holes: Drilling holes 10mm diameter in masonry structure along the side of the joint at 45° angle so as to cross the brick/block at the intervals spacing if 15-30cm depending on extent of rising dampness as per recommendation of engineer in charge. Cleaning of holes: Clean the holes by air blower prior to fixing nozzles. Install Sika® Packer injection packers 9.8mm diameter, 10cm long in the holes and tighten. Fix the packer securely using Sikadur 31. Cutting of Packers: Cut the packers after completion of grouting without damaging structural elements.

Supply and apply of a 3 part, very low viscous, elastic polyacrylic injection resin Sika® Injection 306 with a versatile and adjustable reaction time having Mixed viscosity : 3-11 M.pa.s at +20 Deg C, Reaction time : adjustable according to ambient temperature and execution requirement between 8-50 mins, pH – 9-10, Tested as per Wissbau No. 2002-094-(1A) – Function test with re-injectable hose system. The holes should be drilled until a depth of approx. 5 cm (for a 6cm thick wall) before the end of the wall is reached. Pump Sika® Injection-306 at >20 bar into or behind fissures or into masonry joint which are allowing water to infiltrate into unwanted areas. If voids in masonry being injected contain insufficient moisture to activate the grout inject a small amount of water prior to injecting the grout. When movement stops or Sika® Injection-306 appears at the next packer move to the next packer and inject. If the dampness is heavy, inject similarly at next joint line (Note - only 3 part chemicals like hardener, accelerator and Resin measured and paid in this item after deduction quantities of water part from chemicals solution)

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete,PVC) set in cement mortar, bore of pipe 150mm including necessary excavation up to 2mtr depth including removal of rubbish out side of MoD Land.

M & L Cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipe of 150 mm bore after they are laid and tested.

M & L Salt glazed stone ware ( SGSW ) drain pipes, Grade ‘A’ 150 mm bore, laying level or to falls in trenches, on concrete bed or directly on hard grounds and making joints and testing complete.

M&L cutting into existing manholes for connecting new drains, making good to pipes and rendering, cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1, smooth finished and reforming benching as required for 150 mm internal dia of pipes.

S&F PFRC circular manhole (medium duty) cover with frame of size 551 to 650 mm dia conforming to IS: 12592 and IS:1726, factory made complete all as directed and as approved by Engr-in-Charge

M&L for rebuilding the section of structural damaged spalled concrete or RCC elements to its original size or as per recommendations by engineer-in-charge in thickness up to 40mm in layers of 20 mm each of average thickness 30mm by providing and applying with pre-batched, one component fibre reinforced cementitious polymer modified mortar having compressive strength >= 50 N/mm2 (28 days) according to ASTM C 109; flexural strength >= 5N/ mm2 (7 days) according to ASTM C 293-79 all as specified & directed .

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M&L for point wiring with PVC FRLS insulated unsheathed multi stranded copper conductor of size 1.5 Sqmm 1100 V grade including one run of PVC insulated unsheathed multi stranded copper conductor of size 1.5 sqmm as earth continuity conductor connected to common earth dolly, in existing conduits and its accessories, including replacement of factory made steel boxes suitable for modular switch/sockets including modular plates of suitable size as per site requirement for the following. Note: Cutting & chasing, if required, shall be measured/paid under relevant items.

One light/ceiling fan/exhaust fan point controlled by one no., one way switch 5/6 amps.

One bell / buzzer point controlled by one bell push.

One 3 pin 5 Amps socket outlet point controlled by one way switch on independent board.

One 3 pin 5 Amps socket outlet point controlled by one way switch on same board.

All as per item No 145.00 here-in-before but point wiring with 2.5 Sqmm single core copper cable and earth continuity wire with 2.5 Sqmm single core cable for one three pin 15 amp socket outlet point on independent board complete all as specified and directed.

S&F Modular switch 6 amps 250 V AC one way with ISI mark including 6 amps switch frame complete all as specified and directed.

S&F modular bell push 6 A with Neon 1 module 240 volts complete all as specified and directed.

S&F modular switch 16 A SP one way 240 volts complete all as specified and directed.

S&F modular socket 6 A Multi socket for 2/ 3 pin 240 volts complete all as specified and directed.

S&F modular socket 16 A Multi socket for 2/ 3 pin 240 volts complete all as specified and directed.

S&F electric bell Ding-Dong AC 230 Volt complete all as specified and directed.

S&F ceiling rose, 3 phase/ PVC/ polycarbonate isolated body complete all as specified and directed.

Taking down DB of any type and any way type removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls etc. complete all as specified and directed.

S& F Modular AC/Geyser plug and socket SPN 20 Amps ,240 Volts AC complete with one SP MCB,20 Amps all as directed

S&F sheet metal enclosures for DBs when MCB to be used, SPN double door 240 volt,8 way with 200 amps rated busbar complete all as specified and directed.

S&F in replacement of MCB SPN 40 to 63 Amp 240 volt rupture capacity 10 kA, series 'C' complete all as specified and directed.

S&F MCB SP 6 Amp to 32 Amp 240 volts rupture capacity 10 kA, series 'C' complete all as specified and directed.

S&F in replacement LED batten of 18 Watt 230Volt (size 4 ft), box type complete with LED Tube Light 18 Watt & all accessories internally prewired including connecting up with three core sheathed flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in replacement of Endura Linear LED batten of 10 W (2 ft.), extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver in AC complete all as specified and directed.

S&F in replacement aesthetically designed Wall mounted decorative wall bed side lamp LED light of 5 W fixture with opal diffuser to give glare free light including material of body floral blown glass metal ,suitable LED lamp of 5WW having Lamp base E27 complete all as specified and directed.

Supply & fix in in replacement aesthetically designed Wall mounted decorative mirror LED light of 16W fixture with opal diffuser to give glare free light including suitable LED lamp of 2X8 Watt having Lamp base E27 complete all as specified and directed.

Taking Down ceiling fan 1200mm sweep including fan blade in all respect all as directed and specified Note: The ceiling fan with complete accessories to be safely deposited to MES store.

S&F BLDC copper wounded ceiling fan 5 star rating 1200 mm sweep, regular operated economy range high speed having full copper motor & ribbed aluminium blades for higher air delivery power coating providing longer life complete with accessories 230 Volts including making arrangement of to hanging of fan to ceiling with proper hook nut bolts complete with down rod upto any length as per site requirement along with remote etc complete all as specified and directed by Engr-in-Charge.

S&F stepped type modular type fan regulator on the two module modular sheet etc as required all as directed by Engr-in-charge.

Supply & fix fresh air fan 230mm metallic exhaust fan complete 240V,50Hz single phase AC Supply including fixing on wall with nut washer etc complete and necessary electrical connection from ceiling rose.1mm thickness suitable for 320mm exhaust fan, 12-15 degree tilted, having 3 no. in each set complete all as specified and directed.

S & F geysers 25 ltr capacity , properly fixing with nuts bolts / fasteners connecting with 02 Nos new CP connection , NRV & including complete new vent pipe GI connection up to overhead tank and above of 15 cm.

Disconnecting mains connection and taking out old sub main wiring any size aluminium/copper conductor cable from the concealed conduit from the wall/ceiling and making good to the disturbed surface all as specified.

M&L for submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLS type 1100V grade 2 x 4 sqmm complete drawn in new PVC concealed conduit and its accessories along with 1x 4 sqmm PVC insulated unsheathed copper conductor multi stranded FRLS type cable for continuous earth wire and duly connected to common earth dolly all as specified and directed.

M&L for submain wiring with PVC insulated unsheathed copper conductor multi stranded FRLS type 1100V grade 2 x10 sqmm complete drawn in new PVC concealed conduit and its accessories along with 1x10 sqmm PVC insulated unsheathed copper conductor multi stranded FRLS type cable for continuous earth wire and duly connected to common earth dolly all as specified and directed.

M & L Earthling complete with galvanised steel earth plate electrode, 600x600x6mm thick, buried directly in ground vertically to depth not less than 1.5 meters below normal ground level, connected to galvanised iron earthing strip 25x4mm by means of bolts, nuts, check nuts including necessary excavation and earth work (in any type of strata ) and washers of galvanised iron or steel, CGI watering pipe 20mm bore light grade with funnel and wire mesh, PCC chamber in cement concrete 1:3:6 type c1, 80mm thick pre-cast RCC 1:2:4, type B-1 cover reinforced earth plate surrounded by alternate layers of packed charcoal, salt packed which shall not be less than 15cm in all side of earth plate complete all as shown in electrical plate No 3 of MES schedule Part-I.specified and directed by Engr-in-charge .

M & L in replacement earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/ pipe or fixed to poles or any other indicated situation for loop earthing etc as required 32X6 mm galvanised iron strip.

S & F in replacement of factory made load line DB's double door made out of CRCA mild steel sheet with insulating materials like polyester epoxy coated surface mounting 4 way TPN 415 Volts, IP 43 with suitable busbar, neutral link & earth link suitable for MCCB TP as incomer & MCB SP/TP as out going complete all as specified. Make-Legrand/Havells

S & F in replacement of MCCB TP 125 Amp, 25kA thermal type complete all as specified. Make-Legrand/Havells

S & F PVC non metallic PVC conduit exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.

S & F building security light 45 watt LED base Aesthetically designed luminaire with excellent thermal management.GI bracket of suitable size, fixing with clamp all as directed.

S & F Landscape LED lighting 45 watt at the gate decorative indirect post top garden & landscape lighting with IP 65 protection ,resistant to impact and corrosion anti gate and uniform distribution LED light of 40 Watt

S& F in replacement aesthetically designed wall mounted decorative mirror LED light of 12 W fixture with opal diffuser to give glare free light including FLORAL BLOWN glass metal suitable LED lamp 12 W

M/S Sunil Steel Works

B S R Enterprises

M/s Himgiri construction

BEHAL TRADERS