Repairing and re-carpeting of internal colony roads at Kuchana Housing Complex of Majri Area

Amount

Providing and constructing 50 mm. thick Modified Penetration Macadam (MPM) road surface including all mataerials, preparing the existing road surface, spreading 40mm. stone metal layers 100% crusher broken metal with conical crusher plant heating and spraying the bitumen of specified grade @ 1.75 Kilogram/Square Metre, spreading 12mm.size chips compacting with static roller having weight 8 to 10 MT. to achive the desired degree of compaction as per Technical Specification Clause 506 etc. complete. Including picking of existing WBM surface.(VG-30 bulk bitumen rates are considered to arrive at rates)

Providing and applying tack coat with low viscosity bitumen of VG 10 grade using bitumen pressure sprayer on the prepared bituminous/granular surface cleaned with mechanical broom and as per relevant clauses of section-503 of specifications. (iv) @ 0.40 kg per sqm (Non-bituminous surfaces) granular base not primed.

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A and B seal coats all complete as per clause 511 of specification. (i) Case - I : Type A Providing and laying of liquid seal coat comprising of an application of layer of bitumen binder followed by a caver of story chips. All complete as per clause 511 of specification

Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.09 mm (Type-A) or 13.2 mm to 0.09 mm (Type-B) aggregates using penetration grade bitumen to the required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a Smooth wheeled roller 8-10 tonne capacity & finishing to required level and grade all complete as per clause 508 of specifications. a) with 60/70 butumen (VG-30) (i) Type-A (Bitumen@ 22 kg per 10 sqm)

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads on Bituminous Surface- Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.complete.

Supplying and Fixing of Molded Shank Raised Pavement Markers / Cat's Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying toSpecifications of Category A of MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm, 100 mm and 102 +/- 2 mm and with minimum reflective area of 13 Sqcm on each side and the slope to the base shall be 35 +/- 5 degree. The strength of detachment of the integrated cylindrical shanks, (of diameter not less than 19 +/- 2 mm and height not less than 30+/- 2 mm) from the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel, to the Engineer.

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density as per clause 404 o specification By Mechanical Means (i) Grading- I (63 to 45mm) (a) Using Screening Type-A (13.2mm Agg.)

Providig and fixing plastic speed breaker with Usage/ Application-Adhesive Epoxy and Bolt, material - Rubber, PVC, Plastic, ABC, Colour-Black & Yellow Black & Lemon Yellow, Number of reflectors - 8, size - 250x350x50mm, Bott Hole - 16, No of Bolts - 16, Diametre- 250 mm x 350 mm x 50 mm, Holes - 16, Weight - 3.6 kg, product type - ABC Plastic speed breaker, Capacity- 40-50 tonne, reflectors on both side. All complete fitting including as per Engineer-in-Charge.

Total impact of GST for the purpose of CTC

Sandeep Jain

VINOD N MANIYAR

Alok Ranjeet Saha

M/S R. V. SUNKURWAR

Shri R. V. Umbarkar