REPAIR/REPLACEMENT OF SANITARY FITTING AND OTHER B/R WORKS AT UMROI MIL STN UNDER GE UMROI

M&L for preparation of old painted surfaces by washing, rubbing down and stopping of distempered and painted surfaces of walls and applying a coat of distemper oil emulsion over wall care putty of 1.0 mm thick wherever required as per direction of Engr-in-charge complete all as specified and as directed. Note: Material & labour for wall care putty will be measured and paid separately.

M&L for preparation of old painted surfaces by washing, rubbing down and stopping of distempered and painted surfaces of walls and applying two coat of distemper oil emulsion over wall care putty of 1.0 mm thick wherever required as per direction of Engr-in-charge complete all as specified and as directed. Note: Material & labour for wall care putty will be measured and paid separately.

M&L for preparation of old painted surfaces by washing, rubbing down and stopping of distempered and painted ceiling surfaces and applying one coat of distemper oil emulsion complete all as specified and as directed.

M&L for applying 1mm thick wall care putty on internal wall complete all as specified and directed.

Material & Labour for preparation of old plastered surfaces of walls and applying one coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm complete all as specified and as directed. (i) The quoted rate is deemed to be inclusive cost of scaffolding upto 14m high.

M&L for providing and applying two or more coats of weatherproof 100% acrylic exterior emulsion paint of approved shade and colour with one coat of primer/sealer as per manufacturer specifications on the external surface of the building such as external walls including preparation of surfaces by removing and cleaning old existing paint, dirt, algae, fungus, shrubs, etc. completely by scrapping with wire brush and washing with water or with bio-wash complete as specified and directed. (i) The quoted rate is deemed to be inclusive cost of scaffolding upto 14m high.

Material and labour for providing and fixing 10 mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over existing timber or metal frame work including dismantling of old unserviceable ceiling complete all as specified and directed

M&L for providing and applying two or more coats of acrylic emulsion paint (interior grade) of approved shade and colour with one coat of primer/sealer as per manufacturer specifications on the internal wall surfaces of the building including preparation of surfaces by removing and cleaning old existing paint, dirt, algae, fungus, etc. completely by scrapping with wire brush and washing with water or with bio-wash complete as specified and directed.

M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed

Material and labour for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces in two layers (10mm thick 1st layer + 5mm thick finishing layer) as in walls, chajjas, fins, facia etc. any height mixed with water proofing compound (for 5mm thick finishing layer only) @ 3% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement including taking down old existing plaster complete all as specified and directed. Note: (i) Water proofing compound will be measured and paid separately (ii) Cost of scafolding, any height are deemed to be inclusive in the quoted rate.

Supply only waterproofing compound

M&L for preparation of new plastered surfaces of walls and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

Material and labour for 10 mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces as in walls, finished even and smooth without using extra cement including taking down old existing plaster complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over and including wall care putty, minimum 1.0 mm thick and a coat of alkali resistant primer complete all as specified and directed.

Dismantling/taking down existing hessain base felt or clay tiles or any other existing water proofing treatment from roof/chajja including cement plaster, cleaning the surface and removing the dismantled debris to a distance upto 50m and applying 15 mm thick 1:4 cement mortar over cleaned surface and laying water proofing membrane treatment using 3mm thick APP modified membrane consisting five layers membranes with features as specified, weighing not less than 3.50kg/sqm laid over a coat of cold bituminous primer @ 0.40 kg/sqm by torching the membrane and sealing the over lap by 100mm length side and 150mm width side all as per manufacturer's instruction including joints and changes in direction be curved with rendering 10mm thick in cement mortar 1:3 mixed with SBR latex @ 200ml/bag of cement curved well before laying of membrane, including applying two coats of solar reflective bituminous aluminium paint @ 0.10 litre/sqm all as per manufacturer's instructions and to the satisfication of Engr-In-Charge complete all as specified and directed. Note: (i) Irrespective of lap the net covered area will only be measured for payment. (ii) The quoted rate is deemed to be inclusive of disconnecting and refixing existing water tank and necessary pipe fitting.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness including cover fillets complete all as specified and as directed

M&L for anodised aluminium snap grid frame work for false ceiling of size 600mm x 600mm including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified all as specified.

S&F decorative PVC ceiling board of superior quality of size 600mm x 600mm x 5mm thick fixed in aluminium snap grid frame work including fixing accessories complete all as specified and as directed. Note: (I) Frame work shall be measured and paid separately under respective item. (II) Colour and design of PVC ceiling board shall be approved by GE.

S&F Hollow PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing on and including GI frame as per specifications including taking down existing wall panelling and similar work complete all as specified and as directed.

Dismantling CGI/PPGI corrugated or semi corrugated sheets in wall cladding or roof coverings and hanger doors including re-fixing in same position the aluminium earthing strips after re-fixing/fixing of new sheets complete all as specified and directed.

Fixing only plain or corrugated galvalume aluminium zinc coating PPGL based corrugated/Trapezoidal steel sheet 0.50mm thick as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. Note: (i) Serviceable sheet as obtained from dismantling item here-in-before shall be re-used. (ii) Cost of self tapping screws are deemed to be inclusive in the quoted rate.

S&F pre-painted galvalume aluminium zinc coating PPGL based corrugated/Trapezoidal steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre- painted galvalume aluminium zinc coating PPGL based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, eaves board, fixed with self tapping screws complete all as specified and directed.

M&L for preparation of old steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for coloured non skid ceramics tiles 7 to 8mm thick (square/ rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white/coloured cement to match the existing floor over and including 15mm thick screed bed/bedding layer in cement mortar 1:6 including demolition and removing of existing floor tiles and bedding layers and rubbish of the premisses complete all as specified and directed.

M&L for glazed ceramic coloured /printed tiles 450x300x 7mm/450x600x7 mm/600X300X7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match on vertical surfaces of wall as in skirting, dado, etc. over and including 10 mm thick rendering (backing coat) in cement mortar 1:4, including demolition of existing tiles and cement mortar bedding (but not backing) and rubbish of the premisses complete all as specified and directed.

M & L for vitrified ceramic tiles 7-8 mm thick light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floor, etc. set and jointed in neat cement slurry and pointed in white/coloured cement to match the existing floor laid over and including 15mm thick screed bed/bedding layer in cement mortar 1:6 including demolition and removing of existing floor tiles and bedding layers and rubbish of the premisses complete all as specified and directed.

Taking up or down steel tubing 15mm bore and connections including cleaning for refixing or removal to store and S&F CPVC pipes 20 mm outer diameter of SDR 11 & plain CPVC SDR 11 and fittings as in walls, ceiling, floor, etc. complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 20 cm girth in brick walls etc complete all as specified and directed.

S&F in repair wash hand basin, white flat back of size 550 x 400mm excluding pillar taps but including waste coupling, waste pipe and bracket, PVC connection pipe of 15 mm dia with PTMT nuts of length 600mm, etc.including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

Supply and fix in repair single Piece WC with UF Seat cover, hinges, accessories set, cistern fitting new rimless of size 690 x 375 x 730 mm, white colour complete with all accessories set including fixing bolts and necessary connection with existing pipe complete all as specified and directed.

Supply and fixed in repairs vitreous china squatting pan, Orissa pattern of size 580 mm x 440mm white with P or S trap, front or back inlet and integral foot rest (Excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan EWC (pedestal pattern), white including including plastic water closet seat & back cover with flat bottom and mild steel chromium plated or aluminium anodised high device (excluding flushing cistern and flush pipe) but including fixing bolt and necessary connection with existing pipes complete all as specified and directed.

S&F in repair 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets & flush pipe of polyethylene of low or high density or PVC 32 mm dia for low level cistern including PVC connection pipe of size 15 mm dia, 600 mm long with PTMT nuts complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15cm thickness (below or above ground level) and removing debries from site of work complete all as specified and as directed.

M&L for 75 mm thick cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in plinth protection finished fair and even with using extra cement complete all as specified and as directed.

M&L for repair and rendering 10mm thick in CM 1 :3 on chajjas, facia, roof projection, column sides, beam bottom and sides including throating after removing cracked plaster and concrete including cleaning of visible reinforcement and treating with cement slurry also necessary repair to cracked concrete if any with cement concrete 1:2:4 Type B-0 using 12.5mm graded stone aggregate including necessary scaffolding work for double/single storey bldgs complete all as specified and directed.

Taking down chowkats or frames exceeding 1.50 sqm but not exceeding 4.00 sqm with shutters (without taking off shutters from the frame) complete all as specified and directed

Taking down chowkats or frames not exceeding 1.50 sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

S&F Pressed steel frames for doors of frame size 125x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and directed. Note : Filling of hollow portion of frames with PCC shall be measured and paid separately.

S&F Pressed steel frames for doors of frame size 105x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete as specified and directed. Note : Filling of hollow portion of frames with PCC shall be measured and paid separately.

Material & labour for PCC type C1 1:3:6 (20 mm graded stone aggregate) for filling of hollow frame complete all as specified and directed.

Material & labour for PCC type B0 1:2:4 (12.5mm graded stone aggregate) for fixing hold fasts, angle, etc including necessary form work complete all as specified and directed.

S & F mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges:large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed single side prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet complete all as specified and directed.

S&F second class hard wood 35mm glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) and fitted to chowkhats complete all as specified and directed.

S&F 35 mm thick factory made second class hard wood plain framed panelled shutter (two panel) with lock rail and panel of 9mm thick BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rails and style as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fix Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with particle board core 2, 4 or 6 raised panel design with 2 mm thick Moulded Prelam PVC sheet on the front face & 2mm plain colour PVC sheet on back face and fixing in frame at site as per specification and drawings complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, not otherwise described, over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces complete all as specified and directed .

Supply and fixed stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm fixed with tinned tacks, or stainless steel wire staples including all cuttings, wastage etc. complete all as specified and directed.

S&F 150 mm long extruded aluminium alloy handles, fabricated type, anodized complete all as specified and directed.

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised sliding door bolt with hasp and staples (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium alloy and fixed complete all as specified and directed.

S&F 100 mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

Supply and fix as in repairs aluminium anodised (powder coated) ventilator frame (section for frame 63.5 X 38.1X 1.20mm thick) with shutter(section for shutter 41 x 20 x1.2mm thick)(bottom half portion fixed and top half portion with louver including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete and glazing with and including 4 mm thick frosted glass to aluminium frame work and louver using rubber gasket and fixed with stainless steel wire cloth of 0.36 mm dia and average width of aperture 1.40 mm outside vent with staple and suitable wall angle of size 25.4 x 25.40 x 1.1mm thick and fillets with screws and washers etc including Deco Grill of Model / Design No. DG 104 and 6.3mm thick etc. complete all as specified and as directed.

Supply and fix aluminium anodised (powder coated) Three track sliding window frame with shutters with (2 Nos glazed and one wire gauzed shutter) including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete and glazing with and including 5 mm thick plain glass to aluminium frame work using rubber gasket and including stainless steel wire cloth of 0.36 mm dia & average width of aperture 1.40mm with staple or suitable fillets wire mesh fitted with screws and washers etc including aluminium grill of thickness 5mm and opening not exceeding 75mmx75mm etc with the following section of frame and shutter complete all as specified and directed:- (a) Sections for shutter:- (i) 'H' section: 39 x 20 x 1.20 mm thick (ii) 'Interlock' section: 39 x 20 x 1.20 mm thick (iii) 'Edge & Bottom' section: 41 x 20 x 1.20 mm thick (b) Section for frame:- (i) Top & Sides: 92 X 29.50X 1.20mm thick (ii) Bottom: 92 X 29.70 X 1.20mm thick

S & F anodised aluminium frame, powder coated (minimum thickness 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S & F anodised aluminium powder coated (minimum thickness 50 micron) door shutters, aluminium section weighing 0.75 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, lock, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

M & L for 12 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fitting to aluminium frame complete all as specified and directed

Supply & fixing sheet glass ordinary quality 4.00 mm thick glazing in square/ rectangle not exceeding 0.50 sqm each pane with oil putty or aluminium beads fixed to steel frame, etc. complete all as specified and as directed.

S & F 12 mm thick frameless toughened glass door shutter including providing and fixing top & bottom pivot & double action hydraulic floor spring type with fixing arrangement and making necessary holes etc. for fixing door fittings complete all as specified and directed. Note: Door handle, lock and stopper to be paid separately under relevant item of BOQ.

S & F 12mm thick frameless toughened glass as in partition wall of any height fixed with stainless steel clamp of SS 304 and necessary fittings and fixtures including making good to distured surfaces to match the existing finishes complete all as specified and directed. Note: The rate quoted is deemed to be inclusive of cutting existing brick masonry/RCC/PCC work for inserting SS clamp.

S & F 300 mm long Stainless steel D-Type handle complete all as specified and directed.

S & F Stainless steel Mid lock for glass door complete all as specified and directed.

S & F Stainless steel doom door stopper complete all as specified and directed.

Taking down existing rolling shutter of any description including ball bearing, top cover, anchoring rod, hasp & staple, gear box, crank handle, safety lever lock etc including making good of existing surface complete all as specified and directed

S&F steel rolling shutters of 1.25 mm thick without ball bearing including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: gear operated type with bevel gear box and crank handle all as specified and directed

S&F safety lever locks mild steel with 4 levers for rolling shutters all as specified and directed

S&F ball bearing for rolling shutters all as specified and directed

M&L for preparation existing roof treatment and applying two coats of solar reflective bituminous aluminium paint @ 0.10 litre/sqm all as per manufacturer instructions and to the satisfication of Eng-In-Charge.

M&L for providing and fixing fully perforated 12 mm thick of GRC (Glass fiber reinforced Gypsum) false ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistances of 99%. NRCO 0.50 to 0.75 as per IS 8225:1987, non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (min) to be laid in true horizontal level suspended on interlocking metal T-Grid of GI iron section of 0.33mm thick ( @ 120 gms per Sqm including both sides) comprising of main T runners size of 15 x 32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15 x 32 mm of length 600mm to form grid module of size 600mm x 600mm, suspended from ceiling using GI mild steel items ( @ 80 gm per Sqm) i.e 50mm long , 8mm outer dia M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2 mm. GI iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/partition with the help of plastic raw plugs at 450 mm center to center and 40mm long dry wall wood screws complete all as specified and as directed. Note: (i) The quoted rate is deemed to be inclusive cost of scaffolding upto 14m high. (ii) The texture, design and patterns of false ceiling boards shall be approved by GE before commencement of work.