PROVN OF SEWAGE PIT ALONG WITH SEWAGE PIPES AND MANHOLES NEAR BLDG NO P727 ACCN AT BAIRAGARH SPL REPAIR TO ROOF AT QTR NO P73 BLDG NO P06 AT SI LINES AND TOILET OF BLDG OF 5221 ASC AT GE BHOPAL

Amount

COMMON ITEMS FOR JOB 'A' , 'B' , 'C' & 'D'

Supply only integral water proofing compound complete all as specified and directed. [MAKE: ACCOPROOF/WATER SEAL/MC BOUCHAMIE, MUMBAI/ FOSROC/ CICO/ PIDILITE as approved by GE]

M&L for rendering 15mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 6 to 8mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Use & waste of Form work to edges of concrete flats, openings, floors & roofs and sides of RCC/PCC bands in walls and similar work exceeding 10cm but not exceeding 20cm wide for fair finished surfaces of concrete complete all as specified and directed

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) vent cowl, 110 mm bore complete all as specified and directed.

M&L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cills, seismic and other similar bands, plinth courses, copings, bed plates, bond stones, etc including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work complete all as specified and directed.

M&L for Brick work with fly ash bricks (Modular size), straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

Taking up or down steel tubing and connections 20 mm bore, including cleaning for refixing complete all as specified and directed.

Taking up or down steel tubing and connections 15 mm bore, including cleaning for refixing complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 20 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. [MAKE: TATA/ SURYA/ JINDAL/ PRAKASH as approved by GE]

S&F Steel water tubes, medium grade, ISI marked, galvanised, 15 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. [MAKE: TATA/ SURYA/ JINDAL/ PRAKASH as approved by GE]

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm wood grain printed PVC sheet reinforced with MS square tube complete all as specified and directed. [MAKE:-RAJSHRI / SINTEX as approved by GE]

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and directed. [MAKE:-RAJSHRI PLASTIWOOD/ M/s SINTEX INDUSTRIES/ M/s POLY WINDOWS / M/s DURA PLAST/ M/s ACCUCELL as approved by GE]

S&F Aluminium anodised barrel tower bolts of extruded section, 150mm long complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.

M&L for Glazed ceramic coloured tiles 350mm x 250mm x 7mm thick or 450mm x 350mm x 7mm thick, in vertical surfaces such as skirting, dados and risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:3 complete all as specified and directed. [MAKE: SOMANY/ KAJARIA/NITCO/ ORIENT/ JOHNSON as approved by GE)

Demolition of brick work built in cement or cement lime mortar complete all as specified and directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, ceilings, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1: 4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons, walls, etc, laid bedded and pointed in any mortar complete all as specified and directed.

Removing excavated soil to a distance exceeding 250m but not exceeding 500m and depositing where directed. at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft/loose soil complete all as specified and directed.

M&L for 18-20 mm thick granite (of any type) work (area not less than 1.5 sqm each granite slab, table rubbed and polished) in floors and like; in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Demolition and breaking up drain pipes (SGSW, AC or RCC) of any diameter, set in cement mortar including fittings complete all as specified and directed.

M&L for Providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and setting in cement mortar 1:4 complete all as specified and directed.

Taking down carefully existing point wiring (any type viz. aluminum or copper) with wooden batten/surface PVC conduit (with its fittings)/PVC casing-capping or any other type for light, fan, power point (including switch, socket, ceiling rose, etc.) and making good disturbed surface of wall/ceiling to match with existing surface after necessary rewiring complete all as specified and directed.

All as per BOQ item No.178.00 here in after, but for 3 pin 5 Amp socket outlet on independent board complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way, 5/6 Amps, 230 volt AC, IS: 3854 marked with valid CML No. complete all as specified and as directed. [MAKE:-ANCHOR (PENTA series) or equivalent in LEADER/ CRABTREE/LEGRAND/HAVELLS as approved by GE]

S&F Ceiling rose surface bakelite, three terminals complete all as specified and as directed. [MAKE:-ANCHOR (PENTA series) or equivalent in LEADER/ CRABTREE/LEGRAND /HAVELLS as approved by GE]

M&L in replacement for sub main wiring with approved colour coding as per IS (Red, Black and Green for single phase circuits) with two single core PVC insulated FRLS cable 1100V unsheathed with stranded copper conductor of 6 sqmm nominal cross section area and drawing into non metallic rigid conduit with & including PVC insulated stranded copper conductor of 4 sqmm nominal cross section area as earth wire complete all as specified and directed. [Make of Cable : Polycab/ Plaza/ Havells/KEI/V-MARC as approved by GE] Note: - Two runs of 6.0 sqmm cable, one run of 4.0 sqmm cable of earth continuity conductor & PVC conduit pipe shall be measured as one unit length.

S&F MCB SPN, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 6 to 32 amps complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE]

S&F MCB SP, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 5 to 30 amps complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE]

S&F in repairs replacement LED 20 W/21Watt tube light fitting (T8 type) with and including LED retrofit tube 20/21 W one side connection type, 240 v, PF > 0.90, colour Temp 6500 K, complete with powder coated CRCA decorative patti suitable for surface mounting on wall, complete fitting including connecting with PVC insulated multistranded copper flexible cable 0.5 sqmm two core, and PVC round block white colour x 2 Nos for mounting of fitting complete all as specified & directed. [Make :- WIPRO (Cat No. LED lamp (LL13-181-65SE)(PRO LED LL 13) & batten cat No. (WIO 921208) or C&S (cat Part No. LTDC01220WLED/WD (LED battan T8 TARA -M)) or Havells (Titania LED tube with Regal batten LED) or equivalent in Philips/ Crompton as approved by GE.]

S&F lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings with & including LED lamp white 9 watt retrofit, 230 volts complete all as specified and directed. [Make: for holder:- ANCHOR (PENTA PC SERIES/ LEADER/CRABTREE /LEGRAND /HAVELLS & LAMP : BAJAJ/PHILIPS/SYSKA as approved by GE)

S&F Socket outlet multipurpose having provision for 3 pin, 5 Amp and 2 pin, 5 Amp, piano flush type, 230 volt AC complete all as specified and as directed. [MAKE:-ANCHOR/LEADER/CONA as approved by GE]

OTHER THAN COMMON B/R ITEMS FOR JOB 'A'

BLANK

Excavation over areas, not exceeding 1.5m deep and getting out in hard/dense soil complete all as specified and directed

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for rendering 15mm thick in in cement mortar 1: 3 on fair faces of brick work or concrete surfaces; mixed with water proofing compound (water proofing compound to be measured & paid separately as supply only) and finished fair and even complete all as specified and directed.

Use & waste of Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, for fair finished flat surfaces of concrete complete all as specified and directed.

M&L for Reinforced cement concrete (1:1.5 :3) nominal mix in slabs supported on walls, beams & columns complete all as specified and directed.

M&L for Concrete bed in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate for 150 mm NP-2 pipe including packing under and haunching against the side of pipe complete after pipes are laid, jointed and tested complete all as specified and directed.

M&L for Concrete bed in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate for 200 mm NP-2 pipe including packing under and haunching against the side of pipe complete after pipes are laid, jointed and tested complete all as specified and directed.

M&L for Concrete bed in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate for 300 mm NP-2 pipe including packing under and haunching against the side of pipe complete after pipes are laid, jointed and tested complete all as specified and directed.

S&F reinforced concrete pipes, class NP2, 200 mm bore, laid and jointed with collars complete all as specified and directed

S&F reinforced concrete pipes, class NP2, 300 mm bore, laid and jointed with collars complete all as specified and directed

S&F reinforced concrete pipes, class NP2, 150 mm bore, laid and jointed with collars complete all as specified and directed

M&L for moorum/red bajri filling in floors or pavings, laid in layers not exc. 15cm thick, spread, levelled and blinded with earth and rammed including watering complete all as specified and directed.

BLANK

S&F PVC (SWR) pipes, double socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) pipes, double socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) branch pieces, single (single Y) equal or unequal, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) branch pieces, single (single Y) equal or unequal, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 75 mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 110 mm bore complete all as specified and directed.

OTHER THAN COMMON B/R ITEMS FOR JOB 'B'

Dismantling spoiled, unsound and damaged/ distressed plaster by scrapping with utmost care to expose reinforcement, cleaning the rusted reinforcement by rubbing with wire brushes or emery paper and disposal of debrisout side MOD Land complete all as specified and directed.

Taking down loose concrete / plaster from columns, beams and other structural members by chiseling / scraping carefully without disturbing reinforcement upto a depth of 80mm to 100mm (average) and cleaning the surface neatly with wire brush to remove dust and other foreign particles etc complete all as specified and directed.

M&L for preparing old concrete surface and applying one coat of epoxy based bonding agent by brush to the prepared surface of concrete and getting proper bonding all as per manufacturer's instructions complete all as specified and directed.

M&L for cleaning the reinforcement thoroughly to remove corrosion deposit completely and applying one coat of anti corrosive zinc based primer on surface area of reinforcement all as per manufacturer's instructions complete all as specified and directed.

S&F hard drawn steel wire fabric n.exc 4 Kg/Sqm cut to lengths, bent to shape tying with and including mild steel wire, (annealed) not less than 0.9mm dia as in reinforcement to the height of up to 14 M from ground level complete all as specified and directed.

S&F Mild steel TMT bars 5 to 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for non shrink cementitious micro concrete for jacketing on surface of columns, beams and similar structural members with 5 to 12mm stone aggregate in the ratio as per manufacturer's instructions laid to as thickness as directed with and including applying curing compound and use and waste of necessary scaffolding as required complete all as specified and directed.

Use & waste of Form work to chajjas and similar items including edges for fair finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to fins, louvers, fascia for fair finished flat surfaces of concrete complete all as specified and directed.

Taking down plants / vegetable growth, etc from buildings by cutting /chiseling fully without disturbing structure up to height of 10.00 M from average ground level at different locations and cleaning the surface neatly with wire brush to remove dust and other foreign particles and applying hydrochloric acid (HCL) on leftover root portion and making good the distured surfaces in cement mortar 1:4 complete all as specifed and directed

M/L rendering 10mm thick on fair faces of concrete surfaces with cement mortar 1:4 on ceiling even and smooth in patches without using extra cement finish complete all as specified and directed.

M/L rendering 15 mm thick on stone surfaces or surfaces other than fair faces of brick work in cement mortar 1:4 in small patches area not exceeding 3.0 Sqm each complete all as specified and directed.

M&L for crack filling with approved crack filling compound of M/S Pidilite or equivalent including necessary opening of of cracks, cleaning, watering, etc including necessary scaffolding, etc complete up to height of 8.00 mtr from ground level complete all as specified and directed.

M&L for rendering 15mm thick in two layers, first layer (rendering coat) of 10mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces and second coat (finishing coat) of 5mm thick in cement mortar 1 : 4 mixed with water proofing compound (water proofing compound to be measured separately as supply only) and finished even and smooth without using extra cement complete all as specified and directed.

Taking down existing old roof treatment of any description, type and in any position including removal of old tiles, screed, felt, etc complete all as specified and directed.

M&L for Water proofing treatment to non accessible roof surfaces with APP modified membrane with non woven polyester reinforced, weight not less than 3 KG/SQM and thickness of membrane not less than 3mm having thermal insulation with white mineral/gravel finish on upper side of membrane uniformly embedded during manufacturing process laid in following sequence complete all as specified and directed.:- (a) Conducting ponding test for 72 hrs on the complete area for identifing the worst affected areas and then carrying out grouting (which shall be measured and paid seperately under BOQ serial item No.79.00). After drying of grouting again ponding test for 72 hrs will be carried out for testing water tightness of the surface before processing further treatment. (b) Applying 10mm thick plaster in CM 1:4 mixed with water proofing compound @ 3% by weight of cement on cleaned roof surface. (c) Properly cleaning and drying of the plastered roof surfaces, parapets, gutters, drain mouths, etc for all foreign matters such as fungus, moss, dust, etc by wire brushing and dusting. Proper grooves shall be cut around CI drain outlets/pipes/chimney pipes and other similar situations to tuck in the treatment. (d) Applying a coat of bituminous primer conforming to IS: 3384-1986 @ 0.3Kg/Sqm on the prepared surface till the surface is properly impregnated. (e) Laying APP modified water proofing membrane with 100mm overlap in longitudinal direction and 100mm overlap in transverse direction sealed and bounded to the surface by torch application method. (f) All joints and changes in direction should be curved with cement mortar 1:3 with SVR latex @ 200ml per bag of cement and cured well before laying the membrane. A fillet of PCC 1:2:4 type B-0 using 12.5mm graded stone aggregates shall be provided at all junctions of vertical and horizontal surfaces and wherever there is change of direction. (g) ponding test for 72 hrs will be carried out for effectiveness of water proofing tretment. NOTE:- (i) Work of water proofing treatment shall be got carried out by the authorised applicator of manufacturer. Necessary documentary evidence in support of the authorised applicator will be submitted to Engineer-in-charge before the commencement of water proofing work. (ii) The quoted rates is deemed to include for the cost of scaffolding, T&P, etc required for execution of the work.

M&L for grouting by pressure injection with cement slurry of 50kg cement mixed with Pidicrete SM @ 225 gms of M/S pidilite industries ltd or Cobex 100 of M/S Fosroc Chemicals as per instructions complete all as specified and directed.

M&L for preparing old decorated plastered or unplastered surfaces of walls and applying one coat of white wash complete all as specified and directed.

M&L for preparing old decorated plastered or unplastered surfaces of ceilings and applying one coat of white wash complete all as specified and directed.

Preparing new plastered or un-plastered surfaces of wall and M&L for applying two coats of exterior weather proof water base emulsion paint, white or tinted over and including a coat of white cement base putty on plastered surfaces complete all as specified and directed. [Make:- Apex of M/s Asian Paints or equivalent in M/s Berger or M/s ICI as approved by GE] NOTE:- Work of weather proof paint shall be got carried out by the authorised applicator of manufacturer.

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces with putty and preparation of surfaces for further treatment and M&L for applying two coats of exterior weather proof water base emulsion paint, white or tinted over and including a coat of white cement base putty complete all as specified and directed. [Make:- Apex of M/s Asian Paints or equivalent of M/s Berger or M/s Shalimar as approved by GE] Note: Work of weather proof paint shall be got carried out by the authorised applicator of manufacturer.

M&L for Preparing old painted surfaces of wood and wood based materials of any description over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for Preparing old painted steel & iron surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of surfaces and writing building numbers with figures or letters (Block, Roman, Italic or Indian) with white synthetic enamel paint; letter height not less than 65mm height & 10mm wide; over 150mm dia circle painted with black synthetic enamel paint complete all as specified and directed. NOTE:- Upto 6 letters, hyphen, dash, etc will be condiders as a job e.g. P-1, P-27, T-123, T-81/2.

S&F chicken wire mesh, mild steel 12mm mesh size and 0.56mm dia of wire complete all as specified and directed.

Disconnecting existing water tanks of capacity 500 litres, setting aside (or lowering if required) for repairs, cleaning, etc and hoisting, if required, reconnecting and refixing in position (cleaning, repairing etc to be measured separately) complete all as specified and directed.

Disconnecting existing water tanks of capacity 1000 litres, setting aside (or lowering if required) for repairs, cleaning, etc and hoisting, if required, reconnecting and refixing in position (cleaning, repairing etc to be measured separately) complete all as specified and directed.

M&L for applying 3mm thick wall care putty complete all as specified and directed. [Make: Birla/JK]

BLANK

S&F PVC (SWR) junction double (double T), equal or unequal, 110 mm bore complete all as specified and directed.

S&F PVC (SWR) junction double (double T), equal or unequal, 75 mm bore complete all as specified and directed.

M&L for ShaliCryl ® 215 single component, UV resistant, unique elastomeric, high build exterior waterproofing coating based on a revolutionary acrylic polymer with quick-set capabilities to resist moisture attack applied in following sequence complete all as specified and directed.:- (a) Surface Preparation :- Remove all loose and foreign materials, if any, by a wash with a jet of air / water. Fill voids and undulation area with Polymer Mortar made out of ShaliSBR Latex, Water, Cement and Sand in the Ratio of 1:1:5:12.5. Fill cracks up to 3 mm with PlastiSeal and cracks over 3 mm with PlastiSeal P after opening the crack to a “V” cut. In case of any poor plaster surface in existence (for old building), remove the same and corrected with new cement : sand mortar in the ratio of 1 : 4 admixed with ShaliPlast LW+ @ 200 ml / bag of cement. (b) Primer Application :- Apply ShaliPrime WB as Primer after dilution with potable water in the ratio 1:0.5 for a theoretical Coverage 8-10 sqm per Ltr of the mix and allow it to dry for 3 to 4 hrs. post elimination of undulation, roughness of concrete, joint marks, Voids and any other surface correction. (c) Application of Material:- Apply first coat of ShaliCryl® 215 over the primed surface @ 160 ml per Sqm. Add maximum of 10% potable water by volume for the first coat only, if required, to have brushable consistency only. Allow the applied coating to dry 6 to 8 hrs of application. Apply second coat of ShaliCryl® 215 without dilution over dried first coat @ 140 ml per Sqm and allow it to dry. Do not undertake any further work over the coated area within 72 hrs of final coat. A coat of 100 micron of ShaliCryl TC 100 will improve water / dust repellent property. NOTE:- (i) Work shall be carried out by the authorised applicator of the manufacturer. Necessary documentary evidence in support of the authorised applicator will be submitted to Engineer-in-charge before the commencement of water proofing work. (ii) The quoted rates is deemed to include for the cost of scaffolding, T&P, etc required for execution of the work.

OTHER THAN COMMON B/R ITEMS FOR JOB 'C'

Dismantling asbestos cement/FRP (corrugated, semi-corrugated etc) sheets in roof coverings including ridges complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section, in unframed work in any position complete all as specified and directed.

Dismantling timber in fillets, rails, posts, rafters, purlins, etc under 40 Sqcm in section, in unframed work in any position complete all as specified and directed.

M&L for Cutting holes in brick walls built in cement or cement lime mortar for inserting hold fasts, etc and making good dismantled portion in cement mortar 1:3; cutting exceeding half brick but not exceeding one brick complete all as specified and directed.

M&L for Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc and making good, cutting exceeding 10cm but not exceeding 20cm girth complete all as specified and directed.

S&F Steel work in tubular/structural trusses, purlins, etc including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 or steel sections conforming to Fe 410-W (Gde E-250) quality -A complete all as specified and directed.

S&F Rolled mild steel flat as wind ties conforming to Fe 410-W (Gde E-250) quality -A including securing bolts and all necessary drilling, bolting complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in roof coverings/cladding to wall, etc, fixed with & including self tapping screws on angle frame complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/ JSW as approved by GE)

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet, 0.5mm thickness, of colour as approved by GE, having tensile strength of 550 Mpa as in ridges, etc, fixed with & including self tapping screws complete all as specified and directed. [MAKE: TATA BLUE SCOPE / EVEREST INDUSTRIES/JSW as approved by GE)

Dismantling wall and ceiling boards or insulation boards, any thickness, any description, including cover fillets complete all as specified and directed.

M&L for galvanised cold rolled steel section framework of size 600 x 600mm grid size using 24x38x0.50 (composite thickness) tee (bottom pre coated) & 24x24x0.50mm (composite thickness) wall angle including suspenders as per manufacturer’s instructions complete all as specified and directed. [Make: GAPSON(Gabsec) or equivalent as approved by GE]

S&F asbestos free calcium silicate board of size 600x600x6mm, fixed to steel frame work in ceiling with & including applying two coats of oil bound distemper complete all as specified & directed. NOTE:- Cost of making frame work for light fittings, etc is deemed to be included in the quoted unit rate [Make: GAPSON(Gabsec) or equivalent as approved by GE]

S&F factory made Flush shutters 40mm thick, solid core construction, with block board core and ply wood face panels, commercial type on both sides complete all as specified and directed.

M&L for vitrified light shade flooring tiles 10 mm thick (Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, laid in floors, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tile with & including 15mm thick rendering in CM 1:4 complete all as specified and directed. [MAKE: SOMANY/ KAJARIA/NITCO/ ORIENT/ JOHNSON as approved by GE)

M&L for vitrified light shade tiles 10 mm thick (Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, as in vertical surfaces such as skirting, risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:3 complete all as specified and directed. [MAKE: SOMANY/ KAJARIA/NITCO/ ORIENT/ JOHNSON as approved by GE)

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:4 complete all as specified and directed. [MAKE: SOMANY/ KAJARIA/NITCO/ ORIENT/ JOHNSON as approved by GE)

M&L for Cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in sub floors, leveling course, etc finished even & rough complete all as specified and directed.

Supply, fabricating and fixing powder coated aluminium sections of required size for door windows frames shutters and partitions including aluminium hinges of required size jointing cleats, screws sash fasteners, plug for fixing with walls, columns, etc complete all as specified and directed. [MAKE: JINDAL/ AJIT INDIA/ HINDALCO as approved by GE)

S&F powder coated aluminium mesh, guard/grill of size 50mm x 50mm & wire 5 to 6 mm thick of approved make and pattern cut to the size as required at site and fixing to the aluminium window frame fixed with and including aluminium F- channel and meeting channel complete all as specified and directed. [MAKE: JINDAL/ AJIT INDIA/ HINDALCO as approved by GE)

S&F Sheet glass 4.8mm thick, ordinary quality and glazing to aluminium door, window & partition including pad/gasket, area exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodized, type C-22 , 100 mm size complete all as specified and directed.

S&F powder coated Aluminium handles, cast type, 125 mm size complete all as specified and directed.

S&F powder coated Aluminium alloy, sliding door bolt 300 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F Brass mortice lock, vertical type, 4 lever, 100 mm size suitable for aluminium swing doors complete all as specified and directed

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 150mm complete all as specified and directed.

M&L for Brick work with fly ash bricks (Modular size), straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

S&F decorative mild steel chromium plated, 19mm dia, minimum thickness 1mm, curtain rod with side fixing brackets, rings & decorative knobs complete all as specified and directed.

S&F Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed

M&L for Preparing old painted steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for Preparing new or previously untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and directed.

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means including filling depressions of scrapped surfaces with putty and preparation of surfaces for further treatment and M&L for applying two coats distemper oil emulsion, white or tinted complete all as specified and directed. [NOTE:- 3mm thick wall care cement putty where ever required shall be measured & paid separately.]

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces with putty and preparation of surfaces for further treatment and M&L for applying two coats of exterior acrylic emulsion weather coat paint, white or tinted complete all as specified and directed. [Make:- ACE or M/s Asian Paints or WALL MASTA of M/s Berger or equivalent in M/s Shalimar as approved by GE] [NOTE:- 3mm thick wall care cement putty where ever required shall be measured & paid separately.]

Preparing new plastered or un-plastered surfaces of wall and M&L for applying two coats of exterior acrylic emulsion weather coat paint, white or tinted complete all as specified and directed. [Make:- Apex Paint of M/s Asian Paints or equivalent in M/s Berger or M/s ICI as approved by GE] [NOTE:- 3mm thick wall care cement putty where ever required shall be measured & paid separately.]

Preparing new plastered or un-plastered surfaces of wall and M&L for applying two coats of interior plastic emulsion paint, white or tinted complete all as specified and directed. [NOTE:- 3mm thick wall care cement putty where ever required shall be measured & paid separately.]

S&F in repairs vitreous china wash basin, ISI marked, white, flat back, size 550 x 400mm, including CP waste coupling, 32mm dia PVC waste pipe of suitable length, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed. [MAKE:-SOMANY (Viniek/smart) or equivalent in CERA/PARRYWARE/HINDWARE as approved by GE.]

S&F in repairs vitreous china wash down water closet pan, pedestal pattern concealed, ISI marked, white, with and including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminum hinging device complete all as specified and directed. [MAKE:-SOMANY (EWC concealed) or equivalent in CERA/ PARRYWARE/ HINDWARE as approved by GE.]

S&Fin repairs Vitreous china urinal half stall ISI marked, white, with & including chromium plated waste coupling including connections to flush pipe and outgoing pipes complete all as specified and directed. [MAKE:-SOMANY smart / HINDWARE (Cat No.60002 starwhite) or equivalent in CERA/PARRYWARE as approved by GE.]

S&F in repairs PVC low level flushing cistern 10 liters capacity dual flush, ISI marked, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete all as specified and directed. [MAKE:- SOMANY smart dual flush , Prayag (Cat No.501 Smart flush cistern) or equivalent in PARRYWARE-SLIMLINE/CERA as approved by GE]

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

OTHER THAN COMMON E/M ITEMS FOR JOB 'C'

M&L for point wiring for one light /fan/bell point with 1.50 sqmm (normal area) FRLS PVC insulated, unsheathed, multi-stranded copper conductor cable, 1100 volts grade, controlled by one one-way switch, drawn in & including non metallic rigid PVC casing capping not less than 25 mm base size with all fitting and fixing accessories including one run of 1.5 sqmm copper conductor as earth continuity wire connected to common earth dolly by suitable lugs, sunken sheet steel terminal box made out of 1.20mm thick CI/MS sheet for mounting of fittings like switches , sockets, fan regulators etc with 3mm thick laminated by lum sheet cover complete all as specified and directed. [Make of cable : Polycab/Plaza/Havells/V-Marc as approved by GE) Note : Wiring to be done as per approved colour code in IE rule.

All as per BOQ item No.136.00 above, but for 3 pin 5 Amp socket outlet on independent board complete all as specified and directed.

All as per BOQ item No.136.00 above, but wiring with 2.5 Sq mm copper cable for 5/15 amp switch socket combination on or 3 pin socket out let 15 amp independent board and provision of 1.5 Sqmm, FRLS insulated multi-stranded single core earth wire for earth continuity, connected to common earth dolly complete all as specified and directed.

S&F Switch socket combination, multipurpose, 5 pin, 5/6 Amp, flush type, ISI marked complete all as specified and as directed. [MAKE:-ANCHOR/LEADER/CONA as approved by GE]

S&F Switch socket combination, multipurpose, 6 pin, 5-15 Amp, flush type, ISI marked complete all as specified and as directed. [MAKE:-ANCHOR/LEADER/CONA as approved by GE]

Refixing of tube light fitting any type any make retirieved against Schedule 'A' BOQ item No 38 complete fitting including connecting with PVC insulated multistranded copper flexible cable 0.5 sqmm two core, and PVC round block white colour x 2 Nos for mounting of fitting complete all as specified & directed.

S&F ceiling fan regulator electronic step type 240 V, AC 50 Hz single pole, 100 watts flush type, ISI marked complete all as specified and as directed. [MAKE:-ANCHOR/LEADER/CONA as approved by GE]

S&F PVC insulated, armoured, heavy duty electric cable with stranded aluminium conductor, 1100 volts grade, laid in trenches, sleeving through pipes or fixed on poles & walls or laid under floors including jointing , size of cable 16 sqmm nominal cross sectional area, 2 core complete.

S&F sheet metal enclosure for MCB, DB, SPN, 240 volts, 200 amps rated husbar, 4 way, double door enclosure made upof CRCA sheet steel, RAL 9003 powder coated, IP 43 including wooden rectangle board of first class hardwood of suitable size for mounting of DB box complete all as specified and directed. [Make : Siemens/Legrand/Schinder/L&T/ABB as approved by GE] Note : MCB shall be measured and paid separately.

S&F in repairs MCB SP, 240 volts, 10KA braking capacity, ‘C’ curve, of capacity 40 to 63 Amps including connection with suitable size aluminum/copper lugs complete all as specified and directed. [Make : Siemens/Legrand/Schinder/L&T/ABB as approved by GE)

S&F MCB SPN, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 5 to 32 amps including connection with suitable size aluminium / copper lugs complete all as specified and directed. [MAKE: Siemens/ Legrand/ Schinder/L&T as approved by GE]

M&L for Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical Plate No 3 of MES SSR-2009 Part-I connected to main switch board or main control board all as specified and testing on completion including provision of earth wire protected by 15mm dia light grade GI pipe and watering pipe shall be 20mm bore light grade including all excavation and earth work in any type of soil, PCC pit with pre-cast RCC cover, charcoal/salt, funnel etc complete all as directed. NOTE :- (i) The concrete pit shall be PCC (1:3:6) type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) The unit rate includes the cost of GI pipe medium grade for protection of earth wire and 4mm dia earh lead wire upto 7.5 M. (iii) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself.

OTHER THAN COMMON B/R ITEMS FOR JOB 'D'

S&F double rebate openable/fixed windows made of galvanized steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanized as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 microns, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 72 x 55 mm, centre mullion section 72 x 50 mm, shutter section 47 x 20 mm,fly mesh section 40 x 20 mm and the fixed glass beading section 12 x 12 mm, outer frame and mullions shall consists rebate for glazed shutter, fly mesh and 20 mm provision for guard bars/grills, the sections cut to length mitre joined with corner bracket, centre mullions fixed with mullion cap, stay, handles, latch, 2 Nos of heavy duty stainless steel pivot hinges per shutter and panelled with 5mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade), fitted using EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing windows in the concrete/masonry wall by means of self-expanding screws, including 10mm Square bars welded to 6x12mm flat at a distance 150mm c/c (pitch) etc. complete all as specified and directed. [MAKE:- NCL Alltek and Seccolor Ltd (Model:ECO 4000) or equivalent as approved by GE]

S&F Factory made solid panel 'wood grain finished' PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded wood gain printed PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and 'wood grain finished' PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of 'wood grain finished' PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement and decorative PVC beading of 10mm x 10mm (90 degree) used instead of exposed portion of PVC sheet beading and joined together with solvent cement complete all as shown in SSR-2010 Part-II, specified and directed. [MAKE:-RAJSHRI PLASTIWOOD/ M/s SINTEX INDUSTRIES/ M/s POLY WINDOWS / M/s DURA PLAST/ M/s ACCUCELL as approved by GE) .

S&F Butt hinges, medium weight, cold rolled mild steel, 100 mm size complete all as specified and directed.

S&F Aluminium handles, cast type anodised, 150 mm size complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:4 complete all as specified and directed. [MAKE: SOMANY/KAJARIA /NITCO as approved by GE]

Dismantling, floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:4 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified and directed.

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, including M&L for applying two coats of cement paint white or tinted over & including a coat of cement wash complete all as specified and directed.

Complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, and M&L for applying three coats of white wash including preparation of surface complete all as specified and directed.

S&F in repairs PVC low level flushing cistern 10 litres capacity, ISI marked, white, with all fitting and fixtures including brackets, PVC connection of 600 mm long and 32 mm bore PVC flush pipe, complete all as specified and directed. [MAKE:- SOMANY (Cat No.121002), Prayag (Cat No.501 Smart flush cistern) or equivalent in PARRYWARE-SLIMLINE/CERA as approved by GE]

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (angle type) screwed both ends for iron pipe or for unions 15mm bore, complete all as specified and directed. [MAKE:- Prayag (Cat No.8610) or equivalent in JAGUAR/MARC as approved by GE]

S&F in repairs Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8606) or equivalent in JAGUAR/MARC as approved by GE]

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed. [MAKE:-JAINKO/GEM/SOMA/SHAKTI/CORONET as approved by GE)

S&F in repairs chromium plated shower rose 125 mm size with swivel joints complete all as specified and directed. [MAKE:- Prayag (Cat No.BS-73) or equivalent in JAGUAR/CERA as approve by GE]

S&F in repairs Vitreous china wash basin, ISI marked, white, flat back, size 550 x 400mm, including CP waste coupling, 32mm dia PVC waste pipe of suitable length, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed. [MAKE:-SOMANY (Viniek/smart) or equivalent in CERA/PARRYWARE/HINDWARE as approved by GE.]

S&F in repairs Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8602) or equivalent in JAGUAR/MARC as approved by GE]

S&F PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F Tubular towel rail of brass chromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F PVC waste pipe 32 mm bore suitable for wash basin, etc complete all as specified and directed.

S&F Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm ISI mark, white with integral foot rests including provision of cement concrete bedding & ‘P’ or ‘S’ trap complete all as specified and directed. [MAKE:-SOMANY, PRAYAG (Cat No 4055) or equivalent in CERA/PARRYWARE/ HINDWARE as approved by GE.]

S&F in repairs PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement, dia of outlet 100 mm complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, leveling, watering and well ramming in layers not exceeding 25cm each complete.

S&F salt glazed stoneware drain pipes 150 mm bore, grade ‘A’, laid in trenches and jointed as specified complete all as specified and directed.

M&L for Concrete bed to drain pipes 150 mm bore including packing under and completely surrounding pipes with concrete after they are laid and tasted; in cement concrete 1:4:8 type D2 using 40mm graded stone aggregate complete all as specified and directed.

S&F in repairs PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 110 mm bore complete all as specified and directed.

S&F in repairs PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 75 mm bore complete all as specified and directed.

S&F in repairs PVC (SWR) junction single (single T), equal or unequal, 110 mm bore complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement, dia of outlet 75 mm complete all as specified and directed.

S&F Asbestos cement 6mm thick, corrugated or semi corrugated sheets in roofs, walls etc, fixed with coach screws, including dismantling old AC sheets complete all as specified and directed.

OTHER THAN COMMON E/M ITEMS FOR JOB 'D'

M&L for point wiring for one light /fan/bell point with 1.50 sqmm (normal area) FRLS PVC insulated, unsheathed, multi-stranded copper conductor cable, 1100 volts grade, controlled by one one-way switch, drawn in & including non metallic rigid PVC conduit (ISI marked) medium grade not less than 20mm diameter with all conduit accessories in concealed wiring system by cutting of walls (brick or stone) and making good disturbed surface of wall in CM 1 : 3 (except on ceiling for fan point only, surface casing capping will be used in lieu of concealed PVC conduit) including one run of 1.5 sqmm copper conductor as earth continuity wire connected to common earth dolly, sunk sheet steel terminal box made out of 1.20 mm thick GI/MS sheet for morning of fittings like switches, sockets, fan regulators etc, with 3mm thick laminated hylum sheet cover complete all as specified and directed. [Make of cable : Polycab/Plaza/Havells/V-Marc as approved by GE)

All as per BOQ item No.178.00 above, but for 3 pin 5 Amp socket outlet on same board complete all as specified and directed.

All as per BOQ item No 178.00 above, but wiring with 2.5 Sq mm copper cable for 5/15 amp switch socket combination on or 3 pin socket out let 15 amp independent board and provision of 1.5 Sqmm, FRLS insulated multi-stranded single core earth wire for earth continuity, connected to common earth dolly complete all as specified and directed.

All as per BOQ item No 178.00 above, but wiring with 4.0 Sq mm copper cable for 5/15 amp switch socket combination or 3 pin socket out let 15 amp on independent board and provision of 2.5 Sqmm, FRLS insulated multi-stranded single core earth wire for earth continuity, connected to common earth dolly complete all as specified and directed.

S&F in replacement sheet metal earth plug & socket, single pole and neutral with and including 1 no. single pole MCB 20 Amps 240 volts including industrial plug top complete all as specified and directed. [Make:-Legrand Cat No. 607841 or equivalent in Crabtree/HAVELLS as approved by GE].

S&F switch socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, piano flush type, 230 volt AC IS: 1293-2005 marked with valid CML No complete all as specified and as directed.[MAKE:-ANCHOR/LEADER/CONA as approved by GE]

S&F Switch piano, flush type, single pole, one way, and 15/16 Amps, 230 volt AC, IS: 3854 marked with valid CML No. complete all as specified and as directed. [MAKE:-ANCHOR/LEADER/CONA as approved by GE]

Taking down old unserviceable MCB DB of any size and capacity including wooden boards complete all as specified and directed.

S&F in repairs sheet metal enclosure for MCB, DB, SPN, 240 Volts, 200 amps rated busbar, 12 way, Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 including wooden rectangle board of first class hardwood of suitable size for mounting of DB box complete all as specified and as directed. [MAKE: Siemens/ Legrand/ Schinder/L&T/ ABB as approved by GE] NOTE:- MCB shall be measured and paid seperatly.

S&F MCB SP, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 5 to 30 amps complete all as specified and directed. [MAKE:Hegar (L&T)/ Siemens/ Legrand/HAVELLS as approved by GE]

Taking down unserviceable sub main wiring including service connections, of any size and any description including conduit pipe and making good disturbed surface of wall/ceiling to match with existing surface after necessary rewiring complete all as specified and directed.

M&L for Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubings or conduit wiring, etc and making good, cutting not exceeding 10cm girth complete all as specified and directed.

S&F Integral LED Street light luminaire of 25 W, comprising of pressure die cast housing with epoxy powder coated dark graphite grey colour finish, prismatic polycarbonate cover with individual LED lenses, LED street light luminaires with IP 65 protection and with all fixing arangement, nuts, bolts and washer connecting to electric system with 2.5 sqmm PVC Aluminium stranded conductor 2 core of required length from light fitting to street light control box on pole, testing on completion, complete all as specified and directed. [MAKE: Wipro(Cat No. LR02-291-XXX-57-XX) or equivalent in Philips/ Crompton/Bajaj/Havells/LUKER as approved by GE.]

S&F exhaust fan 300 mm sweep , metal body, complete with louvers incl all civil work like cutting and aking circular opening in existing wall of kitchen etc incl connecting up with win core twisted flexible copper conductor cable with suitable size , complete all as specified and directed.[MAKE:CG/Bajaj/Havells as approved by GE)

Taking down existing u/s fitting and S&F LED 10/9 Watt tube light fitting, surface mounting fitting for mirror light with slik and light weight batton, 240 Volt, with PF >0.95, efficacy >95 , colour temp 6500K complete fitting including connecting with PVC insulated multistranded copper flexible cable 0.5 sqmm two core and PVC round block white colour x 2 Nos for mounting of fitting complete all as specified & directed. [MAKE: HAVELLS (Cat no. LHEXBQP7PN1W009) or equivalent in Bajaj/Crompton/WIPRO/Philips/SYSKA as approved by GE.]

Deduct schedule of credit (calculation will be done off line) Rs.79,294.00

M/S BRIJLAL UPADHYAY