SPECIAL REPAIR AND ADDN ALTN TO BYPASS WATER SUPPLY SYSTEM, VIRHAN GALLEY WATER SUPPLY SYSTEM AND DAG WING PUMP HOUSE AND REPAIRS TO CAC SEWAGE PUMP HOUSE AND EXTERNAL SEWAGE PIPELINE NEAR ITW AT INS SHIVAJI LONAVLA

Amount

Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth and getting out in soft/loose soil including making the bottom of trenches levelled for proper laying of pipe line, foundation etc or for shafts, cesspits, manholes, pier hole etc not exceeding 10 sqm on plan as specified and as directed.

Removing the excavated material not exc 50 M and depositing where directed at a level not exc 1.5 above the starting point in soil complete all as specified and as directed.

Returning and filling including spreading, levelling watering and well ramming in layers not exceeding 25 CM in soil complete all as specified and as directed.

Taking up Cast iron water main including all fittings for spigot and socket ends and lead joints including burning out lead joint and recovering lead complete all as specified as directed for 200 mm bore.

All as per item No.04 above but for 150 mm bore.

All as per item No.04 above but for 100 mm bore.

All as per item No.04 above but for 80 mm bore.

S&F cast Iron Pipes with Spigot and Socket ends centrifugally cast, Class LA laid in trenches including reducing the length of required size complete all as specified as directed for 200 mm bore size of CI pipe. Note :- (i) Excavation earthwork shall be measured and paid seperately. (ii) Mechanical Joints (Rubber Joints) paid separately. (iii) CI fitting will be measured and paid seperately.

All as per item No.08 above but for 150 mm bore.

All as per item No.08 above but for 100 mm bore.

All as per item No.08 above but for 80 mm bore.

M & L for rubber gasket joints for spigot & socket pipes & fittings for following dia of pipes complete all as specified and as directed for 200 mm bore.

All as per item No.12 above but for 150 mm bore.

All as per item No.12 above but for 100 mm bore.

All as per item No.12 above but for 80 mm bore.

S&F cast iron fitting for spigot and socketted cast iron pipe such as bend, tees, pieces, joint piece single branches, junction colar branches, cap plug etc for size 100 mm to 200 mm dia pipes complete all as specified and as directed.

M & L for brick masonary valve pit chambers with and including one brick thick masonary built in cement mortar (1:6)) PCC in foundation 1:4:8 type D2 (using 40 mm graded stone aggregate, rendering 10 mm thick in cm 1:6 internally 10 mm thick rendering in cement mortar (1:4) finished even and fair externally, PCC 1:2:4, type B1 (Using 20 mm graded stoneaggregate) for coping 10 cm thick, 3 mm thick MS plate cover with locking arrangements with angle iron frame of size 40x40x6mm including painting to MS work with two coats of synthetic enamel black paint over one coat of red oxide primer including necessary excavation and earth in any type of soil/strata complete for Internal dimension 1050x1050x1050mm sizes.

S&F in replacement sluice valve class PN-I heavy duty with flanged ends having high stainless steel spindle , cast iron wheel , with shut down and open direction & marked on wheel . (IS-14846-2000) and fixing up complete by providing rubber insertion sheet,nut, bolt, washer etc complete of for 200mm dia CI sluice valves size.

All as per item No.18 above but for 150mm dia CI sluice valves.

All as per item No.18 above but for 100mm dia CI sluice valves.

All as per item No.18 above but for 80mm dia CI sluice valves.

Cutting existing CI Pipe in position for inscertion of tee, branches etc of size 200x 200 x 200 mm (CI fittings measured and paid separately)

Cutting existing CI Pipe in position for inscertion of tee, branches etc of size 150x 150 x 150 mm (CI fittings measured and paid separately)

M&L for run lead jointing of CI pipes including making working pits for carrying out lead jointing and necessary excavation and earth work as required for 200 mm bore size of CI pipes with spigot and socket ends complete all as specified and as directed :-

All as per item No.24 above but for 150 mm bore.

All as per item No.24 above but for 100 mm bore.

All as per item No.24 above but for 80 mm bore.

M & L for brick masonary valve pit chambers with and including one brick thick masonary built in cement mortar (1:6)) PCC in foundation 1:4:8 type D2 (using 40 mm graded stone aggregate, rendering 10 mm thick in cm 1:6 internally 10 mm thick rendering in cement mortar (1:4) finished even and fair externally, PCC 1:2:4, type B1 (Using 20 mm graded stoneaggregate) for coping 10 cm thick, 3 mm thick MS plate cover with locking arrangements with angle iron frame of size 40x40x6mm including painting to MS work with two coats of synthetic enamel black paint over one coat of red oxide primer including necessary excavation and earth in any type of soil/strata complete for Internal dimension 900x900x900mm. sizes

S & F GI tubing medium grade with all new connections and fittings such as tees, bends, elbows, short pieces, connector back nuts, diminishing pieces, caps, plugs unions etc Laid in trenches for 100 mm size of pipes complete all as specified and as directed :-

All as per above Item No 29 but for 80 mm bore.

All as per above Item No 29 but for 50 mm bore.

All as per above Item No 29 but for 40 mm bore.

All as per above Item No 29 but for 25 mm bore.

Taking down unserviceable GI pipe line of 80 mm bore size from the trenches by removing of nut and bolts.

All as per above Item No 34 but for 50 mm bore.

All as per above Item No 34 but for 40 mm bore.

All as per above Item No 34 but 25 mm bore.

S&F in replacement gun metal globe / gate valve with iron wheel bead screwed both ends for iron pipe complete of 50 mm bore size.

All as per above Item No 38 but for 40 mm bore.

All as per above Item No 38 but for 25 mm dia.

S&F in replacement sluice valve class PN-I heavy duty with flanged ends having high stainless steel spindle , cast iron wheel , with shut down and open direction & marked on wheel . (IS-14846-2000) and fixing up complete by providing rubber insertion sheet,nut, bolt, washer etc complete of 100 mm size

S&F in repairs Non return butterfly valves of size 200 mm dia complete all as specified and as directed.

All as per above Item No 42 but for 100 mm dia.

All as per above Item No 42 but for 80 mm dia.

Supply, install and testing of Monoblock pump set suitable for 415 V ,3 phase system having capacity 5 HP consisting of head range 15 to 24 mtr & Flow rate of range 13.5 to 10.3 Lps with suitable upto 20 Mtrs PVC Flexible Copper Power Cable & Suitable Pressure gauge on Delivery side with Auto Coupling, Sliding Bracket & Foot Bend, cables, inclusive of PCC foundation, etc complete including taking down unserviceable pumpset all as specified and as directed. Note- (a) Old UNSV pump set shall be deposited to MES store yard

Supply, install and testing of Pumping sets, centrifugal, electric driven, 18.5 KW/25 HP/30WHP 415 Volts, 50 Hz, 3 Phase, A.C. Supply 1450/1460 RPM, consisting of head range 25 to 35 mtr & Flow rate of range 2400 to 2600 Lpm with suitable upto 20 Mtrs PVC Flexible Copper Power Cable & Suitable Pressure gauge on both Suction & Delivery Side, with Auto Coupling, Sliding Bracket & Foot Bend, cables, inclusive of PCC foundation, etc complete including taking down unserviceable pumpset all as specified and as directed. Note- (a) Old UNSV pump set shall be deposited to MES store yard

M&L for earthling complete with galvanized GI earth plate electrode of size 600x600x6.00 mm, buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to galvanized earth lead wire 4.0 mm dia by means of volts, nuts, check nut and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate as shown in electrical plate No 3 of SSR part1991,20 mm dia watering pipe medium grade 1.50 mtr long GI protection pipe light grade 15 mm dia from earth pit to main board (NOTE:- maximum length of GI protection pipe with each earth shall not be less than 7.5 mtrs) including necessary pit with cover , including testing on complition.

Supply and Fix Star delta Starter fully automatic suitable for For 20 HP Motor 415 V AC

Supply and Fix DOL Starter suitable for 7.5 HP Motor 415 V AC

Supply and fix install and testing of Non clog vertical submersible pumps of 20/25 HP (30WHP) capacity 415 Volts, 50Hz, 3 Phase, A.C. Supply 1440 RPM, with 20 Mtrs PVC Flexible Power Cable (Water Proof Submersible Flat Cable) with Auto Coupling, Sliding Bracket & Foot Bend (Flow Rate 1650 Lpm and Head 30m) with chrome steel impeller and cutter, non-clog to pass 35 mm size particles including guide rail and lifting chain, cables, earthing, etc complete including taking down unserviceable pumpset all as specified and as directed. Note- (a) Old UNSV pump set shall be deposited to MES store yard and RV obtained.

S&F in replacement Flat Submersible Copper Cable of size 16sqmm 3 core all as specified and directed

Taking down old existing LT pannel with all Accessories

Supply, fabricate, errect, connecting, testing & commisioning LT Panel, Indoor Type, weather and vermin proof made out of 2 mm thick CRCA sheet with front opening and locking arrangement, epoxy powder coated having colour siemens grey, 400 Amps capacity aluminium bus bar for phase, 3 No's and 1 No 200 Amp bus bar for neutral, mounted on epoxy insulator including neccessary copper control wiring, heat shrinkable, RYB coloured sleeves over bus bar for identification, earth shields, circular holes at bottom / top to receive incoming and outgoing cable, cable lugs, cable gland of sizes as required floor mounting angle iron frame made out mild steel angle iron of size 40 x 40 x 6 mm grouted on PCC (1:3:6) upto required height suitable for the following control/ fitments sensible for 3 phase, 50 Hz, 415 V system complete with and including following :- INCOMING- (a) Thermal magnetic adjustable FP MCCB of capacity 125 A 35 kA- 1 No. OUT GOINGS- (b) Thermal magnetic adjustable FP MCCB of capacity 63 A 25 kA - 3 No. (c) Thermal magnetic adjustable FP MCCB of capacity 32 A 25 kA - 1 Nos. (d) Multidigital Meter :- 4 No's (e ) Indicating lamp LED type :- 4 sets (f) Star Delta Fully automatic ML 3 Starter :- 03 No's

Demolition of cement concrete in ground floor n.exc 15cm thickness (below or above ground level)

Demolition of Reinforced Concrete n exc 15 cm thickness (below or above ground level)

Demolition of Brickwork or stone masonry, built in cement mortar In CM including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

Dismantling Cast iron or reinforcement concrete drain pipe joint in cement mortar and taking out of trenches 150 mm dia

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing downw ith water, etc.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete.

M&L for Brickwork with sub class B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 in narrow widths including Cutting out bricks/stone, forming toothing for, and bonding new into old brickwork /stone masonry

M&L Rendering 10mm thick in CM 1:6 on concrete surfaces (External surface of manhole) and finished even and smooth without using extra cement complete all as specified

M&L rendering 15mm thick in CM (1:4) on fair face of brick/concrete surfaces on (internal surface of manhole) and finished even and smooth without using extra cement complete with WPC ( wpc measured and paid seperately)

Supply only Water proofing compound

M&L for Pre-cast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in manholes cover slabs with plain fair faces including necessary form work (Reinforcement shall be measured & paid separately).

M&L PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in coping of manhole including weathering, slightly rounded or chamfered angles and throating including necessary form work .

M&L for PCC 1:2:4 type B1,(using 20mm graded stone aggregate) in surface channel and drains (benching of Man holes).

S&F Mild steel TMT bars 10mm dia , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to

M&L for Concrete bed to drain pipes including forming cradles in PCC (1:4:8) type D2 (using 40 mm gradded stone aggregate) for 150 mm dia pipe complete all as specified and as directed

S&F Reinforced concrete pipes, class NP2, laid and jointed complete with collars 150 mm dia laid in trenches and jointed as specified

Shree Ayyappa Engineering

ECOBUILD