Loading
Loading…
Loading…
Tender Value
₹7.2 Cr
EMD Value
₹14.5 L
Closing Date
14 May 2026, 11:00 amClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
GSU/WORKS
16 conditions · 2 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or V, whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of total contractual payments in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover.
The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender.
Cost component of work: (i) Cost Component of Civil engineering works : Rs.6,33,58,203.33/- (a). Cost Component of Civil Engineering works including building work= Rs.43990773.78/- AND (b). Cost Component of Civil Engineering works including shed Fabrication work = Rs.1,93,67,429.55/- AND (ii) Cost component of Electrical(G) works : Rs. 90,31,449.00/-
Similar nature of Civil engineering works: Any Civil Engineering work comprising of Building works, fabrication and erection of Shed/Foot over bridge/PF Shelter/Steel Girder/Composite Girder for (i). Or Construction of any civil 1.1.1 engineering work comprising of building works for component {i(a)} and Any Civil Engineering work comprising of fabrication and erection of Shed/Foot over bridge/PF Shelter/Steel Girder/Composite Girder for component {i(b)}.
Similar nature of Electrical(G) work: "The tenderer should have satisfactorily executed and completed any work as mentioned below: 1.Electrification of service building or Staff quarters or Offices or Road and Colony Lighting or Circulating Area Lighting or Washing Pits or Sheds or Workshops or UTS/PRS or UPS or Battery charging facilities or Pre-cooling facilities or platforms and Yards etc. 2.Erection and Commissioning of LT, HT upto 33KV Overhead Lines or Electrical Sub-station or LT/HT UG power cables. 3. Annual Electrical Maintenance contract of Service building or staff quarters or Electrical sub- station or DG set or Train lighting and/or Air conditioning coaches excluding RMPU units of AC Coaches. 4. Erection and commissioning of any type and 1.1.2 capacity of Electrical Pumping set. 5.Electrification of ON Grid connected or Off- Grid connected solar power plant 6.Electrification of advance Energy metering system or Smart Energy metering system or Prepaid Energy meters. 7.Erection and commissioning or AMC/CMC of Window/Split ACs/Water Coolers/Refrigerators/Ductable package system of air conditioning/ Centralized Air-Cooling unit/Centralized air conditioning unit or hiring of desert coolers/Air coolers. 8.Any above work or combination of (1) to (7) above. The above work must have been carried out in any of the following organization: a)Central Government Department or State Government Department. b)Central Government PSUs or State Government PSUs."
5 conditions · 1 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
In reference to the Railway Board Letter No. 99/CE-I/CT/28(PT) Dated 17/05/2004 Contract can be terminated by issuing notice by Contract Signing Authority on the part of failure of contractor not sought/not willing to seek the extension even after the expiry of the date of completion, and the contract will be ceased to exist with effect from the date of expiry, original or extended as the case may be with forfeiture of PG, Available SD and other Liquidated Damages (LD).
Composite Works (Civil & Electrical/Gen.) in connection with Creation of Trip maintenance/Advance Inspection Centre for Inspection & Maintenance of Electric Locomotives at Durg under Raipur Division/ SECR.
CPM-GSU-R-T-1-26-27
CPM-GSU-R-T-1-26-27
Open
Works - General
15 Months
Raipur, Chhattisgarh
₹0
₹14.5 L
14 May 2026
15 Apr 2026
30 Apr 2026
175 items across 10 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 2,11,78,111.49 | ||
| CARRIAGE OF MATERIALS // By Mechanical Transport including loading,unloading and stacking // Lime, moorum, building rubbish // 3km | — | — | — | 2,16,883.4 | |
| CARRIAGE OF MATERIALS // By Mechanical Transport including loading,unloading and stacking // Steel // 5km | — | — | — | 38,369.54 | |
| CARRIAGE OF MATERIALS // By Mechanical Transport including loading,unloading and stacking // Steel // Beyond 5 km upto 10 km per km | — | — | — | 2,735.14 | |
| EARTH WORK // Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. // All kinds of soil | — | — | — | 4,72,091.02 | |
| EARTH WORK // Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. | — | — | — | 10,095.78 | |
| EARTH WORK // Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. // All kinds of soil | — | — | — | 27,419.02 | |
| EARTH WORK // Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | — | — | — | 3,47,110.76 | |
| EARTH WORK // Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) : // Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: // With Chlorpyriphos E.C. 20% with 1% concentration | — | — | — | 73,319.35 | |
| CONCRETE WORK // CEMENT CONCRETE (CAST IN SITU) // Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : // 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) | — | — | — | 6,30,255.42 | |
| CONCRETE WORK // CEMENT CONCRETE (CAST IN SITU) // Centering and shuttering including strutting, propping etc. and removal of form work for : // Foundations, footings, bases for columns | — | — | — | 44,073.19 | |
| CONCRETE WORK // CEMENT CONCRETE (CAST IN SITU) // Centering and shuttering including strutting, propping etc. and removal of form work for : // Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. | — | — | — | 1,27,766.21 | |
| CONCRETE WORK // MISCELLANEOUS // Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. // All works upto plinth level : // Concrete of M20 grade with minimum cement content of 270 kg /cum | — | — | — | 10,80,316.92 | |
| REINFORCED CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Foundations, footings, bases of columns, etc. for mass concrete | — | — | — | 2,74,233.17 | |
| REINFORCED CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. | — | — | — | 8,69,874.94 | |
| REINFORCED CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Suspended floors, roofs, landings, balconies and access platform | — | — | — | 2,19,414.21 | |
| REINFORCED CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Lintels, beams, plinth beams, girders, bressumers and cantilevers | — | — | — | 3,86,959.27 | |
| REINFORCED CEMENT CONCRETE // FORM WORK // Centering and shuttering including strutting, propping etc. and removal of form for // Columns, Pillars, Piers, Abutments, Posts and Struts | — | — | — | 3,58,097.14 | |
| REINFORCED CEMENT CONCRETE // DESIGN MIX CONCRETE // Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. // All works upto plinth level // Concrete of M25 grade with minimum cement content of 330 kg /cum | — | — | — | 39,70,081.39 | |
| REINFORCED CEMENT CONCRETE // DESIGN MIX CONCRETE // Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. // All works above plinth level upto floor V level // Concrete of M25 grade with minimum cement content of 330 kg /cum | — | — | — | 22,12,504.1 | |
| REINFORCED CEMENT CONCRETE // DESIGN MIX CONCRETE // Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. // All works above plinth level upto floor V level // Concrete of M30 grade with minimum cement content of 350 kg /cum | — | — | — | 23,74,294.82 | |
| REINFORCED CEMENT CONCRETE // DESIGN MIX CONCRETE // Add for using extra cement in the items of design mix over and above the specified cement content therein. | — | — | — | 3,25,147.64 | |
| REINFORCED CEMENT CONCRETE // DESIGN MIX CONCRETE // Providing and placing in position precast reinforced cement concrete waffle units, square or rectangular, as per design and shape for floors and roofs in 1:1.5:3 (1 Cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 10 mm nominal size derived from natural sources), including flush or deep ruled pointing at joints in Cement mortar 1:2 (1 Cement : 2 Fine sand), making necessary holes of required sizes for carrying through service lines etc., providing steel hooks for lifting etc, form work in precasting, handling, hoisting, centering and erection complete for all floor levels but, excluding the cost of reinforcement. | — | — | — | 5,33,997.11 | |
| MASONRY WORK // Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: // Cement Mortar 1:6 (1 cement : 6 coarse sand). | — | — | — | 44,127.65 | |
| MASONRY WORK // EXPOSED BRICK WALL // Brick work with clay flyash F.P.S. (non modular) brick of class designation 7.5 in superstructure above plinth level up to floor five level in : // Cement mortar 1:6 (1 cement : 6 coarse sand) | — | — | — | 13,67,642.76 | |
| CLADDING WORK // Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. // Granite stone slab of colour black, Cherry/Ruby red // Area of slab upto 0.50 sqm | — | — | — | 1,11,616.54 | |
| CLADDING WORK // Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. // Granite stone slab of colour black, Cherry/Ruby red // Area of slab over 0.50 sqm | — | — | — | 70,371.92 | |
| WOOD AND P.V.C. WORK // FRAMES AND TRUSSES // Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). // Sal wood | — | — | — | 1,69,707.5 | |
| WOOD AND P.V.C. WORK // Providing and fixing 25 mm thick shutters for cup board etc. : // Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. // 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | — | — | — | 44,819.79 | |
| WOOD AND P.V.C. WORK // COPER OXIDISED MILD STEEL FITTINGS (COPPER OXIDISED AS PER IS: 1378) // Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : (copper oxidized as per IS: 1378) // 300x16 mm | — | — | — | 717.78 | |
| WOOD AND P.V.C. WORK // BRASS FITTINGS // Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : // 150x10 mm | — | — | — | 923.51 | |
| WOOD AND P.V.C. WORK // BRASS FITTINGS // Providing and fixing bright finished brass handles with screws etc. complete: // 125 mm | — | — | — | 1,630.75 | |
| WOOD AND P.V.C. WORK // BRASS FITTINGS // Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. | — | — | — | 435.71 | |
| WOOD AND P.V.C. WORK // GYPSUM BOARD PARTITIONS // Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer- in-Charge. | — | — | — | 12,983.98 | |
| WOOD AND P.V.C. WORK // GYPSUM BOARD PARTITIONS // Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. // 30 mm thick plain PVC door shutters | — | — | — | 25,376.65 | |
| WOOD AND P.V.C. WORK // GYPSUM BOARD PARTITIONS // Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in- Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. // Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.) | — | — | — | 2,79,019.27 | |
| FLOORING // VITRIFIED FLOOR TILES // Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. // Double charge vitrified tile polished finish of size // Size of Tile 600 x 1200 mm | — | — | — | 3,80,373.45 | |
| ROOFING // Providing, fixing and embedding sand cast iron accessories for rain water pipes in the masonry surrounded with 12 mm thick cement mortar of the same mix, as that of masonry (lead caulking will be paid for separately): // Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. // 110 mm diameter | — | — | — | 15,253.99 | |
| ROOFING // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Bend 87.5 degrees // 110 mm bend | — | — | — | 1,259.44 | |
| ROOFING // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Shoe (Plain) // 110 mm Shoe | — | — | — | 460.96 | |
| FINISHING // CEMENT PLASTER (IN FINE SAND) // 15 mm cement plaster on the rough side of single or half brick wall of mix : // 1:6 (1 cement: 6 fine sand) | — | — | — | 11,34,544.09 | |
| FINISHING // Extra for plastering: // Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. | — | — | — | 7,49,715.69 | |
| FINISHING // Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. // Two or more coats on new work | — | — | — | 1,84,363.81 | |
| FINISHING // EXTERIOR FINISHING // Finishing walls with water proofing cement paint of required shade : // New work (Two or more coats applied @ 3.84 kg/10 sqm) | — | — | — | 23,280.53 | |
| FINISHING // EXTERIOR FINISHING // Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : // Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm | — | — | — | 1,01,104.92 | |
| FINISHING // Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : // Two or more coats on new work | — | — | — | 31,354.77 | |
| FINISHING // Painting with aluminium paint of approved brand and manufacture to give an even shade . // Two or more coats on new work | — | — | — | 77,251.92 | |
| DISMANTLING AND DEMOLISHING // Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. // Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) | — | — | — | 1,50,009.45 | |
| DISMANTLING AND DEMOLISHING // Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | — | — | — | 4,42,345.14 | |
| SANITARY INSTALLATIONS // Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: // White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | — | — | — | 4,596.75 | |
| SANITARY INSTALLATIONS // Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : // W.C. pan with ISI marked white solid plastic seat and lid | — | — | — | 30,837.04 | |
| SANITARY INSTALLATIONS // Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: // White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps | — | — | — | 11,358.76 | |
| SANITARY INSTALLATIONS // Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe. | — | — | — | 5,389.74 | |
| SANITARY INSTALLATIONS // Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | — | — | — | 7,854.04 | |
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : // 15 mm dia nominal bore | — | — | — | 5,786.74 | |
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.-External work // 25 mm dia nominal bore | — | — | — | 6,646.24 | |
| WATER SUPPLY // C.P.V.C. PIPES // Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.-External work // 50 mm dia nominal bore | — | — | — | 52,015.44 | |
| WATER SUPPLY // BRASS FITTINGS // Providing and fixing brass bib cock of approved quality : // 15 mm nominal bore | — | — | — | 1,207.96 | |
| WATER SUPPLY // BRASS FITTINGS // Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : // 25 mm nominal bore | — | — | — | 846.54 | |
| WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : // 25 mm nominal bore | — | — | — | 1,468.35 | |
| WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : // 40 mm nominal bore | — | — | — | 831.99 | |
| WATER SUPPLY // C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES // Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | — | — | — | 77,124.7 | |
| WATER SUPPLY // C.P. BRASS FITTINGS // Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 // 15mm nominal bore | — | — | — | 3,182.63 | |
| DRAINAGE // Extra for depth beyond 45 cm of brick masonry chamber : // Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete // 450 mm dia RCC pipes. | — | — | — | 1,89,671.11 | |
| PILE WORK // Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top of shoe to the bottom of pile cap) : // 550 mm dia piles | — | — | — | 7,27,630.99 | |
| ALUMINIUM WORK // Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in- charge. (Glazing, paneling and dash fasteners to be paid for separately) : // For fixed portion // Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | — | — | — | 17,251.68 | |
| ALUMINIUM WORK // Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in- charge. (Glazing, paneling and dash fasteners to be paid for separately) : // For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) // Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | — | — | — | 10,570.85 | |
| ALUMINIUM WORK // Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in- charge. (Glazing, paneling and dash fasteners to be paid for separately) : // Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): // With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) | — | — | — | 8,108.43 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TenderDocument_1.pdf
ATTACHMENT
TenderSpecialCondition_1.pdf
ATTACHMENT
AnnexuresJMW_1.pdf
ATTACHMENT
GCCApril2022AC1to10_1.pdf
ATTACHMENT
Specialconditionforearthwork_1.pdf
ATTACHMENT
Specialconditoinforearthwork.pdf
ATTACHMENT
Latestspecificationofballast20231.pdf
ATTACHMENT
DETAILEDTECHNICALSPECIFICATIONSCOPEOFWORK_compressed_1_1.pdf
ATTACHMENT
Additionspecialconditionpart-IElectrical.pdf
ATTACHMENT
Additionspecialconditionpart-IIElectrical.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .