PROVN OF TOILET BLOCK WITH AMENITIES AT MECH INF COY ASC TK TPTR PROVN OF SHED AND PLINTH AT VARIOUS ASCON NODES PROVN OF STORE ROOM FOR THE COOK HOUSE OF ASC TK TPTR TYPE AT MIL STN JALIPA UNDER GE A BARMER

Amount

Excavation in trenches not exc 1.5 mtr wide and n.exc. 1.5 mtr in depth for foundation etc. for shafts, wells, manholes etc. n.exc 10 Sqm on plan and n.exc 1.5 mtr in depth and getting out in hard/dense soil.

All as per Sl item No. 1 above but exc 1.5m depth and n exc 3.0m depth and getting out hard/dense soil.

M&L Cement concrete type D-2 1:4:8 40 mm graded aggregate in foundations, filling and mass concrete.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Same as above but dia 6mm to 8mm

M&L for Mild steel TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders

M&L for Formwork for flat finished surfaces to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter all as specified and directed.

M&L for M-25 Cement concrete Foundations, includingrafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified and directed.

M&L for Formwork for flat finished surfaces to sides of square, rectangular and polygon pillars,posts, struts, piers, columns and stanchions

M&L for Reinforced cement concrete (design mix )M-25 in Columns, pillars, piers, posts and struts all as specified and directed.

M&L for Formwork for flat finished surfaces to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M&L for Reinforced cement concrete (design mix )M-25 in Beams, cantilevers, bressummers, lintels over 1.5m span all as specified and directed.

M&L for Cement Concrete Type B1 1:2:4 (20 mm graded aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings,kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M&L for Formwork for flat finished surfaces to chullah hoods, chajjas,troughs and similar items including edges

M&L for Reinforced cement concrete (design mix )M-25 in Chajjas all as specified and directed.

M&L for Formwork for flat finished surfaces to fins, louvers, fascia, roof projections

M&L for Reinforced cement concrete (design mix )M-25 in Fins, fascias, louvres, parapets,roof projections and railings exc.60cm in height, newels,balustrade, and the like all as specified and directed.

M&L for Formwork for flat finished surfaces to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M&L for Reinforced cement concrete (design mix )M-25 in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like all as specified and directed.

M&L for Treating the bottom and sides of excavation sides of column at the rate of 5 litres of emulsion per square metre of surface area

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface of plinth beam (Area of the sub structure in contact with backfill to be measured)

M&L for Treating the top surface of filled earth under the floors at the rate of 5 litres of emulsion per square metre of surface

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete

M&L for 25mm thick cement concrete 1:2:4, type B-0 Damp proof course ( to horizontal or vertical surfaces including necessary formwork

Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m above DPC

M&L for Brickwork with old size fly ash bricks,for masonry straight or curved on plan,built in and setting in mortar 1:4 complete.

Returning, filling in, including spreading, leveling, watering & well ramming in layer s not exc 25 cm in hard /dense soil.

Removing excavation material n. exe. 50m but n exc. 500m & deposited where directed at a level n exc. 1.5m above the starting point

M& L for rendering 10mm thick cement plaster in CM 1:3 on fair faces of brick work on concrete surfaces on ceiling including finished even and smooth all as specified and directed.

M & L for rendering 10 mm thick in cement mortar 1:6 on brick or concrete surfaces finished even and smooth without using extra cement all as specified and as directed.

M & L for Rendering 15mm thick in CM 1:4 on concrete masonary or surfaces other than fair face of brick work with water proofing compound finished fair and even without using extra cement.

M&L for preperation of newly plastered surfaces of walls and applying two coats of oil bound distemper on ceiling surfaces over a coat of alkali resistant primer ocomplete all as specified and directed.

M&L for preperation of newly plastered surfaces of walls and applying two coats of plastic emulsion paint on internal wall surfaces over a coat of alkali resistant primer over 1.5 to 2mm thick wall care putty complete all as specified and directed.

M & L for applying two or more coats of 100% premium acrylic emulsion paint ( 200 micron )having VOC less thean 50 gm / litre and UV resistance as per IS- 15489-2004, Alkali & fungal resitance, dirt resistance exterior paint of required shade (Company Depot Tinned) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over newly plastered surfaces of wall surfaces inlduding 1.5 to 2 mm wall care putty complete all as specified and as directed.

S&F for framed work such as grill gratings etc with ends of bars shouldered and /or reveted or forged into spikes, framed guard bars barred iron doors, ladders framed balusters walk waysrallings, frameowrk of watertanks and similar work

Material and labour for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of zinc oxide primer complete all as specified and as directed

M&L for Sand filling under floors or in foundations,in pinth height including watering and consolidation

M&L for Hardcore of gauge n exc. 63mm,broken stone and boulders deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface

M&L for PCC 75mm thick 1:4:8 type D2 using 40mm graded aggregate as in subbase

Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc. Complete.

M&L for glazed ceramic coloured tiles in verticle surface 350mmx450mmx7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat 10mm thick cement mortar in 1:4 complete all as specified and directed,

M& L For 20 mm thick ,Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and as directed..

M&L machine cut cuddappah stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar partion for drawers laid over cement screed and jointed

M& L Fof rendering 10mm thick cement mortar in 1:4 as in backing coat complete all as specified and directed

M&L For 25 mm thick, type B-1, 1:2:4 (20mm graded aggregate) as in sub base etc complete all as specified and as directed.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor/ wall finishes in CM 1:6.

M&L for PCC 1:3:6 type C1 using 20mm graded aggregate as in filling of pressed steel frames for doors , bed blocks all as specified and directed

S & F Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified,

S&F PVC Solid Door Frame of Size 50X47mm made out of 5.0mm Plain Colour PVC Sheet Reinforced with Mild Steel Square Tube as specified Manufacture’s Instructions complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick with particle board core (stile:), with 2,4 or 6 raised panel design with 5mm thick Moulded PVC Sheet on the front Face & 2mm Plan colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S& fixed Steel door including projecting type hinges, steel handle, complete, with glazing bars, dovetailed or welded ®

Preparation of new or previously untreated surfaces of iron of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a of red oxide primer complete all as specified and directed

S&F of 100mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22

Supply and fixing 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified

Supply and fixing 150 mm long aluminium, anodized barrel tower bolts of extruded section all as specified

Supply and fixing 150mm long extruded alluminium alloy handle, cast type, anodized all as specified

S&F for aluminum anodized three track slinding window with two or more shutter with 4 mm thick plane glass, one shutter of stainless steel mosquito proofing with good quality bearing ,handle lock,etc rubber beading and glazing clips etc using following sections as given in 'JINDAL' catlogue complete all as sspecified and directed.

Aluminium powder coated ventilators partly fix and partly lowered of aluminium section designed DG-2762 (40 mm x 32 mm x1.5 mm thick) (wt 0.668 kg/mtr) frame and DG-2763 and middle section of designed DG-2763 (40 mm x 32 mm x 1.5 mm thick) (wt 0.654 kg/mtr), middle section DG-2546 (17.27 mm x 17.15 mm x 1.22 mm thick) (wt 0.124 kg/mtr) including 5 mm thick pinheaded figured glass louvers with blades of 100 mm heavy duty including with aluminium lever handle fixed panel shall be provided with 5 mm thick pin headed figured glass including all necessary rubber packing, anodized aluminium snap beading fixed with minimum 6 Nos of suitable size galvanised screws with PVC plug etc including taking down old ventilator etc. complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate plinth protection finishing surface even and fair all as specified and directed.

M&L for 38mm wide Glass dividing strips, 3 mm thick in plinth protection every 600 mm distance

M&L for 10mm thick rendering in CM 1:3 mixed with water proofing compound as per manufacturers instructions.

Supply only liquid water proofing compound.

M&L for PCC 1:2:4 type B1 using 20mm graded aggregate 40mm thick as in padding concrete in roof including cement slurry @ 3Kg/Sqm

M&L for priming coat of concrete/plaster surface with bituminous primer at 4 Kg per 10 sq metre and as specified and directed by Engr-in-charge.

M&L for laying of APP based polymeric membrane minimum weight 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150gm/sqm) laid on primed surface by torched application and as per manufacturer instructions complete and all as specified and directed.

Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI(solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

S&F For 1000 ltr. Capacity rotational moulded polyethylene water storage tanks cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

M&L 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F 20mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling all as specified and as directed.

S&F 25mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling all as specified and as directed.

S&F 25 mm outer dia gate valve/ ball valve for , screewd both ends for CPVC pipes and fixed complete all as specified and as directed

S&F of Grating round 140mm with waste hole made out of stainless steel complete all as specified and directed.

Cutting chase, pining in making good to facings where required & pointing in cement mortar1:3 to ends etc or edges of landings, steps cills,sunshades, shelves,lintels,etc and cutting chasesfor concealed water tubing and making good,cutting n.exc. 10cm girth in brick walls all as directed.

S&F in repairs 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls and ceilings complete all as specified and directed.

S&F PVC bends of 110 mm dia complete all as specified and directed.

S&F PVC (SWR) floor trap, plain including jointing with solvent cementbends of 75 mm dia complete all as specified and directed.

M & L for half stall ceramic urinal pastel coloured of size 720x485x310mm (Make - Hindware / equivalent approved make indicated in list of make in tender) including Urinal toughned glass / Marble / Granite including grinding,polishing,rounding/moulding/chamfering edges), brass cp bottle trap, electric operated auto censor / Push cock (Including spraders ) flushing arrangements. (Make Hindware or equivalent approved make indicated in list of makes in tender) Note : Type of partition will be decide by Engr-in-charge as per sitr requriment 2) Type of flushing arrangement will be decide by Engr-in-charge. Note : The rate quoted by the contractor is including the connection push cock & spraders.

S & F in repair table top wash hand basin vitreous china coloured including CI bracket, 15mm dia polythene connection, 32mm dia chromium plated (CP) waste coupling chain and plug waste filling union and 32mm dia PVC waste pipe 90cm long, all necessary inlet outlet connections complete all as specified and directed. Make : Hindware or equivalent model in Cera /Parryware/ Neycer as approved by GE.

S&F in repair viterous china wash down water closet pan(pedestal pattern) white(including fixing bolts, flushing cistern and flush pipe) including provision of flush pipe , plastic seat cover for pedestal pan and cp health faucet including two way angle cock complete all as specified and directed.Make : cera

S&F For in repair brass chromimum plated two way bib cock fancy type, 15mm bore ( min Wt. 550 grams) of approved make by EIC/ GE etc.complete all as specifed and as directed.

S & F in repair For brass chromium plated, 15 mm bore healthfoucet, ( flexy type) 1.00 mtr. Long of approved make by EIC/GE etc. complete all as specified and as directed.

S&F in repair 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down , screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair Brass chromium plated tubular towel rail, 20mm dia , D type 60cm long between flanges complete all as specified and directed.

S&F in repair For sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with stain steel bracket guard and railing 60 cm long etc. complete all as specified and as directed.

S&F in repair 15mm dia concealed stop valve chromium fancy type , screwed down, high pressure , with crutch or butterfly handle , screwed both ends for iron pipe or for union complete all as specified and directed.

S& F in repair Soap dish holder complete as specified and directed by Engr-in-Charge. (Jaquar

S& F in repairBrass CP mixer for mixing hot & cold water screwed down for15 mm size iron pipe and fixed

S&F vitreous china squatting pan "Orrisa Pattern" size 580x440mm white with integral foot rest(including flushing cistern) but including flush pipe, trap complete all as specified .Make : cera

S&F in repair 10 ltr capacity PVC valveless , syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including brackeet and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete

S&F in repair overhead shower complete

S& F in repair Wash hand basin mixer complete as specified and directed by Engr-in-Charge. (Jaquar

Excavation over areas 1.50m in depth for foundation etc or for shaft, wells, cesspits, manholes , pier holes etc n exc 10 Sqm on plan and n exc 1.50 m in depth and getting out in average soil.

Excavation over areas for depth beyond 1.50 mtr in hard dense soil and getting out

M & L for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete

M & L for Brick work with fly ash bricks straight or covered on plan exc 6m mean radius built in cm 1:4.

Loose filling with broken bricks,aggregates of gauge 80 to 150 mm in sokage well

M & L for RCCM 20 using 20mm graded stone agg as in Walls, retaining walls, basement walls, ballasts wall and the like ; any thickness above top of footing including attached pilasters and buttresses .

M & L for RCC M 20 using 20mm graded stone agg as in slab supported on walls, beams and columns in floor, roof landing, balconies, canopies, dech slab and in shelves and the like

Use & Waste of form works to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work, rough finished surfaces not exceeding 200mm thick

Use & Waste of form works to edges of concrete flats trades , breaks in floor , window cill, concrete, opening in concrete walls floor and roof n exc 20cm wide and sides of RCC / PCC bands in walls , horizontal or sloping and similar work exc 5 cm but n exc 10 cm wide for rough finished concrete surface.

M & L mild steel deformed bars 6-8mm dia and over cut to length bent to shape required including cracking bending spirally for hoping for columns, hooking ends and binding with and including mild steel wire not less that 0.9 mm dia or securing with clips.

M&L for RCC (1:2:4), type B1 (using 20 mm graded stone aggregate) Precast cement concrete cover slab for manhole and similar article with plain face, set in cement mortar 1:4 complete all as specified and direceted.

M & L rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surface finished even and smooth w/o using extra cement

Supply only integral water proofing compound @ 2.5% by weight of cement

Removing excavated material n.exe 50m & depositing where directed at a level n.exe 1.5m above the starting point.

S&F in repair 75mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

All as per item No 16 above but 110mm complete all as specified and directed.

S&F in repair 75mm PVC(SWR) bend any radius complete all as specified and directed

S&F in repair 75mm PVC(SWR) junction single(single T) equal or unequal complete all as specified and directed.

All as per item No 21 above but 110mm bore of pipe complete all as specified and directed.

S&F in repair 75mm PVC(SWR) vent cowl complete all as specified and directed.

All as per item No 22 above but 110mm complete all as specified and directed.

M&L for Reinforced concrete pipes 200mm bore class NP-2, laid and jointed complete with collars, complete all as specified and as directed.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in concrete bed to drain pipes including packing under & haunching against the sides of pipes after they are laid & tested for 200mm bore pipe set in cement mortar, PCC bad and haunching, complete all as specified and as directed.

M & L cutting hole in brick walls/stone walls exc one brick but not exc 2 bricks for any perpose and making good dismantled position in cement mortor 1:3 or cement concret 1:2:4 type B-1 as required complete all as specified and directed by Engineer-in Charge.

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15 cm, deep and getting out in hard/dense soil complete all as specified and directed.

Supply only Fine aggregate (sand) for sand cousioning

M & L Machine pressed precast concrete interlocking pavour block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with glossy finish colour shade complete all as specified and directed by Engr-in-Charge.

M&L precast solid block masonry of block 1:3:6 type C-1 wall exceeding 10 cm in width and built in cement mortar 1:4 complete all as specified and directed.

M&L Preparation of newly plastered or unplastered surfaces on wall surfaces and applying two coats of cement base paint over a coat of primer complete all as specified.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, in hard / dense soil returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,

S&F rolled sections as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc Fe-410-W(Gde E-250) Quality A complete all as specified and directed.

S & F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc. complete all as specified and directed.

S& F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley, gutters etc. complete all as specified and directed.

M&L for preparation of New or old previously untreated steel or iron surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Excavating over areas, exc 1.5 m deep and getting out in hard/dense soil

Forming embankments/ upto plith level including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5 m high from base ®

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified & directed by Engineer-in-charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling, Jodhpur type brought upto courses.

M&L for 100 mm thick cement concrete 1:2:4, type B-1 (20mm graded aggregate) as in floors,hardstanding without using extra cement complete all specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection including making joint at every 3mtr interval and at corner and filled with mixture of bitumen and sand and finished even and fair and laid in alternate bays complete all as specified and directed.

M&L for rendering 15 mm thick cement plaster in CM 1:6 on stone masonry surface or other than fair face of brick work incl finishing even and smooth without using extra cement complete as specified and directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of external walls and applying two coat of cement base paint @ 5sq.m/kg/1 coat over a one coat of of external primer

M&L for Non Skid ceramic tiles colour tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified. Note : Work will be in patches or in bulk

M & L for Machine cut kota stone slab flooring 20-25mm thick over, laid over cement screed base , jointed and pointed with grey cement slurry mixed with pigment over 20mm thick cement mortar 1:6 screed bed to match the shade of the slab including rubbing and polishing complete all as specified and directed.

S & F Factory made ISI marked flush door shutters 35mm thick, BWP conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 2nd class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters complete all as specified and including supply and fixing following items As approved by Accepting Officer : (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

S&F for aluminum anodized three track slinding window with two or more shutter with 4 mm thick plane glass, one shutter of stainless steel mosquito proofing with good quality bearing ,handle lock,etc rubber beading and glazing clips etc using following sections as given in 'JINDAL' catlogue complete all as sspecified and directed.

M&L for point wiring in concealed with PVC insulated, unsheathed, single core multistandard copper conductor cable( FRLS) of size 1.5 Sqmm, 1100 volts grade including 1.5 Sqmm PVC insulated, unsheathed, copper conductor cable for earth continuity wire to be drawn through in and including PVC conduit medium grade ISI marked with its acessories including necessary modular metal flush box/pressed steel terminal boxes and modular white cover plate ISI marked of suitable mudule switches, sockets, fan regulators etc. including all necessary wall cutting chases and making good disturbed surfaces in cement mortar 1:3 for one light /CB point controlled by one switch, complete all as specified and as directed by Engineer-in-charge

(a) All as item number 01 above but exhaust fan/ ceiling fan

(b) All as per item no 01above but for one socket outlet 3/2 pin, 5 Amp, point on the same board with other switches.

All as per item no 01 here-in-before but with cable 4 sqmm including 4 sqmm cable as earth wire for 15/16 amp socket point.

Supply and fix Modular Socket, 6A/16A - 2/3 pin combined 2 module.

Supply and fix Modular switch 1 way 16 A, 1 module.

S&F Surface and wall mounted LED batten 20 watts 4 feet long, extruded aluminium housing and polycarbonate diffuser provided for efficient heat dissipation & integrated electronic driver including connecting up with and including twin/three core twisted flexible cable of suitable size in flexible conduit all as specified and as directed . Make :Havells, Cat No:LUMILINEPLUSNEOBS20WLED865SPCSSIND or techno-commercially equiv In Wipro/Philips

S&F Surface and wall mounted LED batten 10 watts 2 feet long, extruded aluminium housing and polycarbonate diffuser provided for efficient heat dissipation & integrated electronic driver including connecting up with and including twin/three core twisted flexible cable of suitable size in flexible conduit all as specified and as directed . Make :Havells, Cat No:LUMILINE+BS10WLED865SPCSS or techno-commercially equiv In Wipro/Philips

S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Sullpy and fixing polycarbonate celling rose surface type

Supply and fix Modular switch 1 way 6 A, 1 module.

Supply and fix exhaust fan 250 mm sweep with louvre plastic body complete fixed to window/wall with suitable fastening and connecting up including provision of cable from connector to fan with flexible copper conductor cable 24/0.2mm and taking down the existing exhaust fan and deposit in MES store complete all as directed.

S&F sheet metal enclosure, (for DB's when MCBs to be used), flushed in wall single pole and neutral Double door, 8 way, 240 Volts with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and as directed.

Supply and fixing single pole 06 to 32 A rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing andcommissioning, complete all as specified and as directed

All as per Item No 14 but SPN 32 A rating complete all as specified and as directed

Supply, installation, testing and commissioning of water heater storage type(Geyser 50 Ltrs)capacity 5 star rating, waterelectric suitable for single phase ,50HZ, AC supply, stainless steel inner assembly, 2 KW heating element, Twin thermostat for water temperature and safety thermostat stove enamel outer body including minimum 1M of three core 2.5 sq mm twisted copper conductor cable PVC sheathed, three pin plug top, polyethylene pipe connection piece 450mm long of 6Kg/sq,CM with two sets of chromium plated adopter at each end suitable for 15mm bore GI pipe at cold water inlet and copper tubing connection with chromium plated adopter at ends, at hot water outlet, with safety fusible plug confirming to relevant ISI of 50 ltrs capacity and GI pipe, connection, globe valve, brass ferrule all as fixed and testing all as directed by Engr- in- charge.

M&L for Earthing complete with galvanised steel pipe electrode, 40mm bore,medium grade, 2.5 metres length,buried directly and preferably vertically in ground with top edge not less than 1.25 metres below ground level connected , earthing test point all as specified and indicated including testing on completion by using galvanised iron 25x4mm strip as earthing lead on completion for desired result complete all as specified and directed by Engr-in-charge

M & L for Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cables, erection of poles, struts/stays, leveling of yard etc not exceeding 10 M² on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

M&L for unwashed river sand cushioning to U/G cable and punning for cushioning of cable 8cm below the cable and 15cm above cable all as specified and directed. Note :- Thickness after punning shall not be less then 18 cm. Punned thickness shall only be measured and paid.

M & L for Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cm in soil.

M & L for Removing of excavated soil not exc. 50 M from starting points all as directed .

Supply & laying in repair XLPE insulated armoured, heavy duty electric UG cable with aluminium conductor 1100 volts grade complete including providing lugs as required as specified and directed for cross sectional area 16 sqmm 2 core

Supply & laying in repair XLPE insulated armoured, heavy duty electric UG cable with aluminium conductor 1100 volts grade complete including providing lugs as required as specified and directed for cross sectional area 25 sqmm 3.5 core

Supply & laying un reinforced precast concrete cable cover class LV type 1 flat, size 250 mm x 150 mm x 40 mm as machenical protection to underground cable laying with lenth of the cable cover equal to the width

S&F MCB, SPN 'C' Curve, 240 Volts, 32 Amps.complete all as specified and as directed . Make : Indoasian /C&S /Legrand

Supply & fixing TPN aluminium bus bar box outdoor type of 200 A capacity mounted on porcelain brridge insulator for one incoming cable and two out going cable, housing in sheet metal enclosure of MS sheet metal inclosure of MS sheet 3.0 mm thick CRCA sheet and angle iron 40x40x4 mm frame, painted with two coat including arrengement for cable gland for incoming and out going cable, locking arrengement ,suitable foundation/plateform for mounting the FPB with space for and including the following switch gears:-(a)MCCB 63 A FP ,10 KA (for incoming control)

Tubes, 'light grade', galvanised, with all fitting; laid in trenches for road/drain crossing of size 40 mm

Supplying, laying , jointing and testing GI tubes, medium grade (ISI marked), galvanized iron with and including all fitting (ISI marked) such as bends, tees, sockets, nipples & unions, flanges etc laid in trenches/fixed to wall/fixed on pillars etc complete all as specified and as directed of following sizes :- GI pipe 25 mm bore

Supply and fixing gun metal globe / gate valve heavy duty with iron wheel head, screwed both ends for jointing iron pipe and fixed, suitable for 25 mm bore, complete all as specified and as directed

NOTE:- (i)- Quantities are clubbed in BOQ for three Jobs. Item's qty details as per Annexure on Sl. Pg. No. 38 to 40 of tender.

RAMDEV ENTERPRISES (BID ID -3459471)