Comprehensive maint in MES Installation (Electric Supply and Water Supply) at Mil Stn Fazilka

Amount

SCHEDULE 'A' SECTION I (B&R Portion)

Taking down chowkats or frame with shutters(without taking off shutters from the frame not exceeding 1.50 sqm each & removing to store all as specified.

Taking down chowkats with shutters(without taking off shutters from the frame exceeding 1.50 sqm each but not exceeding 4 sqm)

Taking down shutters refixing in same opening but area exceeding 1.00 Sqm and not exceeding 2.0 Sqm all as specified.

S & F pressed steel door frames with one or more rebates including necessary fixing lungs hinges lock strike plate etc complete all as specified size of frame 105 x 60mm all as specified and directed.

S & F pressed steel door frames with one or more rebates including necessary fixing lungs hinges lock strike plate etc complete all as specified size of frame 125 x 60mm all as specified.

Ditto all as per item No 11.00 as above but size of 75x60 mm as in cup board frames all as specified and directed by Engineer - in-Charge.

M&L Cement concrete 1:2:4 type B–1 filling of pressed steel frame and hold fast blocks etc all as specified and directed.

M&L 18-20 mm thick block board ,grade 2 quality ,interior grade ,decorative type with decorative face veneer on both faces including wooden beeding around the edges of board ,fixed with screws to Pressed steel frame work all as specified and directed by GE.

S & F continous (Piano)type hinges mild steel bright finish or lectro galvanised with wide of flaps 30mm complete all as spd and directed.

S&F 35mm thick 2nd class hard wood glazed Skelton shutters open rebated and prepare to receive glass gauges etc without sash bars edges of gramng plain chamfered or rounded fluted without and mixed beads for securing gases etc size of chambers as specified in SSR Part I sector 8-20 (a) fitted to chowkat.

S & F flush shutter 35mm thick solid core construction with block board core and plywood face panels commercial type on both sides with lipping / frame to match all as specified.

S&F Stainless steel tower bolt 150mm long heavy duty all as specified and directed .

S&F stainless steel handles of size 150mm heavy duty all as specified and directed .

S&F Stainless steel sliding door bolt with hasp and staple ( bolt type) and fixing clips of sheets cast or extruded section and fixing bolts of extruded section or stainless steel 300mm size all as specified and directed .

M&L machine cut kota stone slab flooring 18-20mm thick in single piece over cement screed base laid and jointed with grey cement mixed with pigment to match the shade of the slab including rubbing,polishing and chamfering the edges of steps inculding screed bed or bedding layer of mortar 15 mm thick CM (1:6)all as directed by Engineer-in-Charge.

M&L for kota stone slab flooring 18-20mm thick in single piece in riser of steps,skirting,dado and pillar laid and jointed with grey cement mixed with pgment to match the shade of the slab including rubbing and polishing complete inculding screed bed or bedding layer of mortar 15 mm thick CM (1:6)all as directed by Engineer-in-Charge.

M&L for grinding & polishing of old kota stone slab flooring complete all as specified

M&L 18- 20mm thick granite (of any type ) work (table rubbed and polished ) in cooking platform and like in cm (1:4) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including cutting and moulding the edges half round on exposed side complete all as specified and directed by Engineer-in-Charge.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons

S&F in repairs, steel window 1.25mm thick box type (primer coated) ERW hollow 'P' section of size 60mm x 25mm single rebated comprises guard skeleton shutter ERW section 50mm x 20mm and 1m thick with two openable leaf consisting two Nos. of sash bars of flat iron 12mm x 3mm complete welded to frame with one vertical mullion of ERW box type 'T' section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B1 four Nos. for each window including following fittings welded to thr frame complete all as specified and directed by Engineer-in-Charge. (a) Hold fast 150mm long of 12mm x 3mm made to shape - 04 Nos. Per Window (b) Handle of 'Z' section 20mm x 25mm, 100 long - 01 No. Per Leaf (c) MS tower bolt 150mm long - 02 Nos. Per Leaf (d) MS pintol hinges of size 100 x 14mm - 02 Nos. Per Leaf (e) 'Z' section 20mm x 25 mm x 100mm long stopper Per leaf Make : M/s Tee Pee Enterprises, M/s Friends Manufacturing Co., Kotkapura, Note : Wire Mesh and painting shall be measured and paid separately under appropriate item of BOQ

S&F powder coated anodized aluminum frame for doors, windows , ventilators with one of more rebates including joining cleat for fixing etc. completed all as specified

S&F powder coated aluminum window/ventilators shutter side hung type without sash, aluminum section weighing glazed clips, rubber packing anodized aluminum fittings such as peg stays 150 mm long (1 nos) hinges type B-21 100 mm long (2 Nos) suitable handle (1 Nos) complete all as specified.

S&F aluminum anodized grill diamond shape 100mm x 100mm aperture of 6 mm dia round bars including necessary joining cleats, clips anodised complete all as specified.

S&F sheet glass 5.5mm thick ordinary quality and fixed in alum section To glass panes as per instruction of manufacturers in squares not exceeding 0.50 sqm in each pane

S&F in repairs aluminium (die cast) body, door closer hydraulically regulated designation No. 3 , universal type , suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80 kg and fixed.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

M&L in repairs Aluminium Motrice lock 4 levers and 75mm size for aluminium doors

M & L for providing and injecting chemical emulsion for post constructional antitermite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.50 Ltrs per Sqm of the vertical surfaces of the sub-structure to a depth of 300 mm including excavating channel along the wall and rodding etc. complete all as specified and directed. Note : Quantity will be measured perimeter of wall x depth of penetration.

M&L preparing surface of wood and wood based surface new on any description not other wise described over 10cm with or grith and applying two coat of synthetic enamel paint over a coat of pink primer all as specified and directed .

S&F galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width or aperture 1.18mm

S&F in repair galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width or aperture 1.18mm

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

Hacking out old broken glass (any size,thickness,quality or description from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified & directed by Engineer -in-charge.

S&F sheet glass 4mm thick ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 sqm in each pane

S&F in repair MS 300mm ordinary rat tail rod pattern springs including roller and roller plate complete.

Taking down and refixing of alum window shutters of any size in same opening incl repairs /replacement of rubber packing,glass,glazing clips & aluminium section etc (The item glass,glazing clips & alum section will be measured seperately)

Taking down aluminium door shutter , Refixing in the same opening after tightening of members ,refixing of glass panes and rubber bids inluding adjusting of old hydraulic door closer complete.

S&F for 150mm floor door stopper of aluminium alloy body and tongue,anodised with hard drawn steel spring,fixed in floor.

S&F 2nd class hard wood plain solid, straight chowkats and frames wrought,frame rebated on the solid,rounded or chamfered,put together with glue pinned at joints,supplied and fix as in cupboards

S&F Aluminium handle cast type anodized 100 mm long as in cupboards.

S & F of 100mm hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws .

S & F of 30 mm width of flaps Continuous (piano) hinges, mild steel, bright finish or electrogalvanised

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), remving serviceable tiles to stores and and rubbish off the permises.

M & L for glazed ceramic coloured tiles 7mm thick 300 x 450mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 10mm thick cement sand plaster (1:3) complete all as specified and directed by Engineer - in - Charge.

M & L for glazed ceramic coloured tiles 7mm thick 300 x 200mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to tile shade over and including 10mm thick cement sand plaster (1:4) complete all as specified and directed by Engineer - in - Charge.

M & L vitrified ceramic light shade coloured tiles with matt finish, 10 mm thick ( square/ rectangular ) polished, area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement paste pigmented to tile shade over and including 15mm thick cement and sand screed (1:4) complete all as specified and directed by Engineer - in - Charge.

M&L Non skid ceramic coloured /printed tiles 7 to 8 mm thick( square /rectangular) area of each tile exc. 0.11 sqm but n. exc, 0.18 sqm and shall be jointed in neat cement slurry and pointed in paste pigmented to tile shade over and incl 15 mm th screed bed in CM 1:6 complete all as specified and directed by Engr in Charge.

Hardcore of gauge n exc. 63 mm brick bats, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L 75mm thick PCC type D-2, (1:4:8) using 40mm graded stone aggregate

M&L Coloured Chequered cement concrete tiles 30cmx 30cmx 25mm thick gloss finish, set, jointed & pointed in neat cement slurry in floors with grey cement & pigment over 15mm thick screed in CM(1:6)

M&L 50mm thick PCC type C-1, (1:3:6) using 20mm graded stone aggregate Finished even & smooth without using extra cement as in plinth protection

Demolition of cement concrete ( un re-inforced) of any description in ground floor and pavings Nexc15 cm thickness (below or above GL)

S & F 110mm PVC (SWR) pipes and single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm PVC(SWR) bends any radius complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and as directed by the Engineer-in-Charge. Make : Dr Fixit/Fosroc/BASF/STP

M&L 40mm th PCC 1:2:4 type B-1 using 20mm graded aggregate as in flooring, finished even and smooth with using extra cement.

M & L cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in lintels up to 1.5 m clear span, seismic and other similar bands, benching, coping, bed blocks, apex stones and kerbs etc including use of necessary form work all as specified and directed by Engineer - in - Charge .

M & L RCC 1:1½:3, (nominal mix), Type A-1, using 20mm graded aggregates as in chajjas, fins, fascias, louvers, parapets and railing etc and the like including necessary formworks all as specified and directed by Engineer - in - Charge.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for.

Demolition of brick work or stone masonry built in cement mortar including all quoins, pillars, arches etc. but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and as directed.

M&L Brick work with old size burnt fly ash bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed by Engineer - in - Charge .

M & L 25mm thick cement concrete flooring type B0 1:2:4 using 12.5 mm graded aggregate on roof slab.

Taking down cement or cement lime plaster from brick walls etc including raking out joints, hacking for key scrubbing down with water etc.

M & L 10mm thick rendering in Cement Mortar 1:3 on fair faces of brick work or concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer - in - Charge .

M & L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even & smooth without using extra cement all as specified and directed by Engineer - in - Charge .

M & L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even & smooth without using extra cement all as specified and directed by Engineer - in - Charge .

M&L for Rough cast plaster complete all as specified and directed by Engineer-in-Charge. Note : Rendering coat not less than 10mm thick in C:M 1:3 , while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg size 6 to 12mm mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished eaven

M & L two coat of white wash on old decorated plastered or unplastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in - Charge .

M & L two coat of white wash on old decorated plastered or unplastered surfaces of ceiling including preparation of surfaces complete all as specified and directed by Engineer - in - Charge .

M & L three coats of white wash including preparing new plastered or unplastered surfaces of ceiling complete all as specified and directed by Engineer - in - Charge.

M & L Preparation of newly plastered surfaces by applying one coat of interior grade wall putty and making it smooth with sand paper by mechanical method i.e. with hand electric grinder then applying two coats of oil bound distemper all as specified by mechanical method i.e. spray gun all as specified and directed by Engineer-in-charge.

M & L Preparation of Old plastered surfaces by removing old treatment and applying one coats of interior grade wall putty and making it smooth with sand paper by mechanical method i.e. with hand electric grinder then applying two coats of oil bound distemper including all as specified by mechanical method i.e. spray gun all as specified and directed by Engineer-in-charge.

M & L applying one coat of cement base paint on old decorated plastered surfaces of walls including preparation of surfaces by washing, rubbing down and stopping of painted surfaces complete all as specified and directed by Engineer - in – Charge

M & L applying two coat of cement base paint over one coat of white wash on new plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in – Charge.

M & L Preparation of Old plastered surfaces by removing old treatment and applying one coats of exterior grade wall putty and making it smooth with sand paper by mechanical method then applying two coats of weather proof exterior emulsion over a coat of exterior primer complete all as specified and as directed by Engineer-in-Charge.

M & L for preparation of old painted wooden surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint all as specified and directed by Engineer - in - Charge .

M & L for preparation of old painted steel surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint all as specified and directed by Engineer - in - Charge .

M & L providing two coats of synthetic enamel paint over new surface and a coat of red oxide primer on steel surfaces including preparation of surface of any description not exceeding 10 cm width or girth all as specified .

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets

M&L for 4mm thick E board fibre cement designer ceiling board of Everest make embossed texture of size 595x 595 mm fixed with screws to snap grid works including GI frame work channel 0.55mm thick frame work in ceiling complete all as specified and directed

M & L running welding in repairs thickness of metal exc 6mm n exc 9mm

Taking down and refixing of rolling shutters including greasing,oiling,repairs/replacement of part of any size exc 3.00 sqm but not exc 7.5 sqm area ( the defective parts to be seperately in concern items )

Supply of 1.25mm thick MS sheet laths complete all as specified & directed by Engineer-in-charge.

Supply of tension spring suitable for rolling shutter of any size all as specified & directed by Engineer-in-charge.

Supplying and fixing retro reflective Overhead informatory road signage and boards, made up of 2 mm thick aluminium sheet,face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTMD- 4956-01 as approved by Engineer-in-charge,letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

Desmantling plain, coraugated steel sheeting any guage, thickness including nanital or similar pattern roof covering.

Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each and removing from site

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications and drawing complete or as directed .

S&F factory made solid PVC door shutter 30mm thick(style) consisting of frame made out of MS tubes for bottom and top rails. MS frame shall be covered heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail& bottom rail on either side & as gap insert for top rail & bottom rail; Panelling for plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling and fixing in the frame at the site as per specification.

S&F Aluminium handle cast type anodized 125 mm long all as specified.

S&F Aluminium anodized barrel tower bolt of extended section and fixed 125 mm long all as specified and directed.

S&F 100 mm long butt hinges extruded almiunium alloy with galvanised mild steel hinges pin, anodised and fixed all as specified and directed .

S&F Aluminium anodized barrel tower bolt of extended section and fixed 150 mm long all as specified and directed.

S&F Aluminium handle cast type anodized 150 mm long all as specified.

S&F Aluminium alloy, anodised sliding door bolt with hasp and staple ( bolt type) and fixing clips of sheets cast or extruded section and fixing bolts of extruded section or stainless steel 300mm size all as specified and directed .

S&F 100mm Butt hinges, medium weight, cold rolled mild steel, and fixed

S&F Aluminium handle cast type anodized 100 mm long as in cupboards.

M&L 18-20 mm thick block board ,grade 2 quality ,interior grade ,decorative type with decorative face veneer on both faces including wooden beeding around the edges of board ,fixed with screws to Pressed steel frame work all as specified and directed by GE.

S & F of 100mm hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws .

S & F of 30 mm width of flaps Continuous (piano) hinges, mild steel, bright finish or electrogalvanised

S & F rotational moulded polythene three layered white coloured water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 500 Litres all as specified and directed by Engineer - in - Charge .

M&L ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball with minimum weight 210 gm screwed for 20mm bore iron pipe supplied and fixed complete all as specified and as directed by Engineer-in-charge.

S & F in repairs PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve, float and handle including brackets, flush pipe of PVC 32mm bore and connection to WC pan complete all as specified .

S&F in repairs vitreous china wash down water closet pan padestel pattern white including connection pipe to union of flushing cistern, inlet and overflow pipes,connecting only to flushing cistern anti-syphonage pipe with PVC flush pipe of 32mm dia and plastic seat cover with mild steel chromoum plated hinging and 'P' or 'S' trap device complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous china,white, wash hand basin, flat back size 550x400mm 'including MS brackets including cutting for and pinning in, but excluding waste pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair bib taps long body, 15mm bore dia, fancy type, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe all as specified .

S & F in repairs 15mm bore CP Angle cock one way chromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified .

S&F in repairs 15mm stop valves fancy type, chromium plated ,cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed.

S&F in repair pillar taps 15mm bore dia, fancy type, cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed by Engineer – in – Charge. Make :Jaquar / Cera / Parryware / Hindware

S & F in repairs for brass chromium plated toilet paper holder fixed on wall with PVC washers and dash fastnersas per sample approved by GE.

S&F in repairs soap dish,chromium plated, 100X100X60mm, fixed to wall with plugs with chromium plated screws complete all as specified and directed.

S & F brass chromium plated tubular towel rail 20mm dia “D” type 60 cm long between flanges incldg brackets complete all as specified and directed by Engineer - in - Charge .

S&F in repair CP grating suitable for 75/100 mm bore floor trap and fixed with white cement.

S&F in repair PVC connection both side brass unions internal for size 15mm dia and 600mm long all as specified and directed by Engineer-in-Charge.

S&F PVC waste pipe 32mm dia & 90 cm longall as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing of 15 mm bore and connections, including cleaning for re-fixing or removal to store

Taking up or down steel tubing of 20 mm bore and connections, including cleaning for re-fixing or removal to store

S&F chlorinated PVC (CPVC) pipes 20 mm outer dia, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.0 m spacing . this includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete all as specified and directed. Make : Supreme/Vectus or equivalent.

Supply & fixing mild steel tubes of size 20 mm bore (medium grade) galvanised with all fittings and fixed complete to wall all as specified & directed by Engineer-in-charge.

Fixing only mild steel tubes of size 20 mm bore (medium grade) galvanised with all fittings and fixed complete to wall all as specified & directed by Engineer-in-charge.

M & L three coats of white wash including preparing new plastered or unplastered surfaces of walls complete all as specified and directed by Engineer - in - Charge.

M & L providing two coats of synthetic enamel paint over new surface and a coat of red oxide primer on steel surfaces including preparation of surface of any description not exceeding 10 cm width or girth all as specified .

RUCHIKA CONSTRUCTIONS

EAGAL CONSTRUCTION COMPANY