REPAIR/MAINT OF INTERNAL ELECTRIFICATION INCLUDING FANS AND GEYSERS AT CADETS LIVING ACCN AT NDA KHADAKWASLA

Amount

Repair / maintenance of internal light fitting of any type like tube lights / wall bracket light fittings / ceiling lights / bulk head light / mirror lights incuding switches etc in its position, testing all the compenents / parts, wiring etc, identifying and replacing the defective components like tube rod, side holders, holders, lamps, switches, sockets, ceiling roes, etc all as directed by Engr-in-charge. Note: (i) The rate against the above mentioned item is deemed for cost of labour only. (ii) Cost of spares like capacitor, lamp holder, connector, connection wire etc. replaced against above mentioned item will be measured & paid for separately under respective items of Sch 'A' here-in-below. (iii) The contractor's representative will report to concerned JE E/M at 0900hrs daily to collect the list of defects and will submit the completion report on following day before 0900hrs to the JE E/M. (iv) The contractor shall rectify the defects and make the light fittings functional within 24 hours from the time the list of defective lights is handed over to him / his rep by the concerned JE E/M. In case the light fitting is not made functional for whatsoever reason within the specified time limit, an amount of Rs 100/- per such defective light fitting per day will be recovered from the amount due to him through RAR / Final Bill.The contractor shall engage separate team of technicians / repairer for each at Offr Md accn, MES Colony/MES installations & Bombay stadium/PTT area. (v) The contractor shall maintain proper record of repair / maint in a binded compliant register and complaint slip books duly signed by the user and bringing out the details of spares replaced and get it authenticated from concerned JE E/M on daily basis. The contractor shall put up the maint record register to Engineer-in-charge for inspection every Monday or as and when asked for. (vi) The contractor shall maintain sufficient stock of spares / material required for repair / maint of light fittings with the concerned JE E/M against the supply only items here-in-below.

(a) Supply only Retrofit pendant lamp holders suitable for table lamps or wall bracket light fittings or for ceiling lights

(b) Supply only PVC / polycarbonate Angle/Batten type lamp holders retrofit type

(c) Supply only switch piano flush type 5 Amps SP one way complete all as specified.

(d) Supply only switch piano flush type 20 Amps SP one way all as specified.

(e) Supply only socket outlet 3 pin 5A flush type complete all as specified.

(f) Supply only socket outlet 2 in 1 3 pin 5 and 15 Amp flush type complete all as specified.

(g) Supply only ceiling rose, 3 terminals /PVC/ Polycarbonate, isolated body.

(h) Supply only table lamp fittings white colored suitable for B-22 base cap CFL/bulb with necessary accessories including surface PVC box of circular/square type all as specified. Make: As per the sample provided by the Engr-in-charge

S&F in replacement of fan regulator electronic step type suitable for 1200/1400 mm sweep fan as per the sample provided complete all as specified and directed

S&F in replacement of modular fan regulator, 2 module, suitable for ceiling fan of 1200/1400mm sweep complete all as specified and directed

S&F in replacement of Modular socket 6 A 2/3 Pin 2 module. complete all as specified and directed

S&F in replacement of Modular socket 6A/16A - 2/3 Pin 2 Module. complete all as specified and directed

S&F in replacement of modular switch 1 way 10 A 1 module. complete all as specified and directed

S&F in replacement of modular switch 1 way 20 A 1 module with neon indicator. complete all as specified and directed

S&F in replacement for modular switch 2 way 10 A 1 module. complete all as specified and directed

S&F in replacement of 1 and 2 module Blanking plates. complete all as specified and directed

S&F in replacement of door bell AC 230 volts single phase ding dong typecomplete all as specified and directed

M&L for securing loose wiring and repair to point wiring with necessary rigid non metalic PVC casing caping double lock type ISI marked inclusive all accessories complete as specified and directed.

Taking down carefully copper/aluminium point wiring (light/fan/socket) including all accessories wire, casing caping/conduit, screws etc and making good the disturbed surfaces complete all as specified and directed

M&L for point wiring with 1.5 sq mm copper conductor FRLS (multistrand) PVC insulated ISI marked unseathed cable and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 25 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 1.5 sq mm copper conductor as earth wire to common earth dolly including PVC box suitable for modular type switches, sockets, fan regulator etc for following :- (a) One light/Fan point controlled by one way switch 6 Amps 240 volts

(b) All as per item No 21 above but One 3 pin 6 Amps socket out let point on independent board.

(c ) All as per item No 21 above but One 3 pin 6 Amps socket out let point on same board.

(d) All as per item No 21 above but One light point controlled by two 6 Amp two way switches .

M&L for point wiring with 2.5 sq mm copper conductor FRLS (multistrand) PVC insulated ISI marked unseathed cable and including surface, Non metalic rigid PVC casing capping double lock type ISI marked not less than 25 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 2.5 sq mm copper conductor as earth wire to common earth dolly including PVC box suitable for 15 Amps socket outlet power point independent circuit complete all as specified and directed

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6.3mm thick, burried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia of minimum 15m length by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 in SSR PART-I connected to earthing test point all as specified or indicated including provision of earthing lead protection pipe, PCC earth pit with cover, excavation & earth work, testing on completion etc all as specified and directed

S&F in replacement of GI pipe bracket of 25 mm dia 1 mtr long bend to shape for street light fitting made out of 25 mm dia GI light grade pipe fixed on pole using suitable FI clamp including necessary new nut, bolt and washer complete all as specified and directed.

S&F in replacement LED security light fiitting 30 W,IP-65 protection made up of die cast alluminium housing with high power LED as lighting source and lens embeded PC cover having TOP opening seperate driver compartment complete all as specified and directed. Make: Lukar Cat Part:LSTE30(Sleek series) or equivalent in make as mentioned at makes list in PS

S&F in replacement stator motor suitable for light duty fresh air ventilation fan of any sweep(approx 225/250mm) and replacing plywood of not less than 15mm with duly coated with synthetic enamel paint as per the existing arrangement complete all as specified and directed.

M&L for sub main wiring with two single core PVC insulated FRLS cables with stranded copper conductors 2.5 Sqmm , 1100 Volts grade in and including casing caping/conduit medium grade not less than 25 mm complete with conduit accessories and copper cable 2.5 sqmm continuous earth wire drawn on wall/ceiling/through stair case/wooden surface with all accessories and incl cutting of existing surfaces of any type and making good to match with the existing surfaces acrylic sheet work complete all as specified and directed. Note: Two runs of 2.5 Sqmm cable with 01 run of 2.5 Sqmm earth wire along with casing caping/conduit shall be measured as one RM

Ditto as per item No 30 above but 2 x 4 sq mm with one continuous earth wire of size 4.0 sq mm Note : 2 runs of 4 sq mm cable and one run of 4.0 sq mm earth wire and PVC casing/capping will be measured as one meter.

Ditto as per item No 30 above but 2 x 6 sq mm with one continuous earth wire of size 6.0 sq mm Note : 2 runs of 6 sq mm cable and one run of 6 sq mm earth wire and PVC casing/capping will be measured as one meter.

Taking down carefully sub main wiring of any type and size and making good disturbed surfaces complete as directed.

Taking down ceiling fan/exhaust fan of any sweep for servicing / repairing / maintenance, opening up, identifying and replacing the defective parts, cleaning, greasing,etc, reassembling and hanging up/fixing back at its original position, connecting up and testing complete all as directed. Note : 1.Cost of spares such as capacitors, bearings etc will be measured and paid for separately under respective Item of sch A as supply only.

(a)Supply only capacitor of 1.5 mfd for wall fans. Make: Epcos/Tibcon/Crompton

(b)Supply only capacitor of 2.5 mfd for ceiling fan/exhaust fan. Make: Epcos/Tibcon/Crompton

(c)Supply only bearing No.6201/6202/6203/6204 or any other No matching to the existing size and suitable for ceiling fan/exhaust fan/wall mounted fan of approved make

(d) aluminium fan blade for exhaust fan of any sweep/make as per the sample given by the site-in-charge.

Disconnecting electric connection and taking down carefully fan of any type and size/sweep as described below, removing the burnt winding of fan motor rewinding with super enarneled copper winding wire of suitable gauge or of matching size to the exisiting wires including all insulating material such as insulation paper sleeve, tape, varnishing etc and reassembling, testing, transporting back to site and refixing to original position all as directed (a) Celling fan of size 1200/1400mm sweep.

(b)All as per item no 39 above but Air circulator fans/Pedastal fans of size 600/450 mm sweep wall mounting Oscillating type

(c) All as per item no 39 above but Wall mounted fans size 350/400 mm sweep Oscillating.

(d) All as per item no 39 above but Exhaust fan of 225/300 mm sweep.

M&L for Preparation of old surface of exhaust fan of any sweep by removing old paint using paint remover or by burning off using blow lamp and cleaning with cloth and Spray painting complete exhaust fan with superior quality synthetic enamel paint (Smoke gray) after applying primer complete all as speicified and directed.

All as per item no 43 above but Air circulator/Pedestal of size 450/600 mm sweep with superior quality enamel paint (Grey) complete all as specified and directed.

All as per item no 43 above but Ceiling fan of size 1200/1400 mm sweep with superior quality enamel paint ( Milk White) complete all as specified and directed.

S&F in replacement MCB DB 04 way SPN (double door) sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar, flush/surface mounting complete including taking down the existing DB of any type & size by removing from existing circuits and refixing the new DBs and circuits and making good the distrubed surface as required at site complete all as specified and directed. Make: Havells QVE Plus DHDMSHODOW04 or equivalent in make as mentioned at makes list in PS

All as per item No 46 above but 08 way SPN DB (Double door) Make: Havells QVE Plus DHDMSHODOW08 or equivalent in make as mentioned at makes list in PS

S&F in replacement factory made epoxy powder coated Distribution Board TP & N 4 way double door (VTPN MCCB DB) MCCB as In comer, and MCB as outgoing with metal door (IP-43 protection) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout semi flush to wall and making good disturbed surface and touch up with the same finishes complete all as specified Note: MCCBs and MCBs will be measured and paid seperately under respective Sch A item in the schedule

S&F in replacement of MCB single pole 6-32 Amps working on 240 volts, 50 HZ AC, 10 KA 'C' curve complete all as specified and directed.

S&F in replacement of MCB DP 6-32 Amps working on 240 volts, 50 HZ AC, 10 KA 'C' curve complete all as specified and directed.

S&F in replacement of MCB SPN 40- 63 Amps working on 240 volts, 50 HZ AC, 10 KA 'C' curve complete all as specified and directed.

S&F in replacement of MCB TP 40-63 Amps working on 415 volts, 50 HZ AC, 10 KA ,'C' curve complete all as specified and directed.

S&F in replacement of MCCB with rating of 100 Amps,415Volts 3pole with 16kA breaking capacity,thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu).MCCB should be with suitable spreaders and phase barriers for each terminals complete all as specified and directed.

S&F in replacement of MCCB with rating of 125 Amps,415Volts 3pole with 16kA breaking capacity,thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu).MCCB should be with suitable spreaders and phase barriers for each terminals complete all as specified and directed.

S&F in replacement of Metal body ventilation fan of 225 mm sweep inclduing replacing the plywood as per the site requirement complete all as specified and directed. (Note: Old Exhuast fan should be deposited in MES store yard) Make: Bajaj MAXX AIR/ Crompton Greaves Trans Air/ Havells VENTILAIR DB NEO or equivalent makes as mentioned at makes list in PS

S&F in replacement of Plastic ventilation fan with BLDC motor, energy efficient of 200/250/300 mm sweep inclduing replacing the plywood as per the site requirement. Note: Old Exhuast fan should be deposited in MES store yard) Make: Atomberg/ Crompton Greaves Trans Air/ Havells.

S&F in replacement of high speed wall mounted fan of sweep 400 mm,,Full copper motor,auto thermal overload protection,compact style and powder coated gurads & pull cord switch for speed regulation and oscillation control including connectng up the power cord to the socket and necessary fixing accessories all as specified and directed. Make:Crompton or equivalent in Havells/Bajaj

Disconnecting and taking down existing userviceable geyser of 100 ltrs capacity, taking it to civil workshop for repairing.Opening the geyser and dismanting all parts and taking out inner tank/container, removing dents making to shape including welding / brazing the leakage portion, filling the portion between inner tank and out casing of geyser with new glass wool heat insulating material . Reassembling and painting the outer casing of geyser with two coats of superior quality synthetic enamel paint(existing colors) and re- fixing to original place all as specified and directed. Note: part required for replacement shall be measured and paid separately under respective supply only item

(a) Supply only safety valve(dead weight) suitable for geyser of 100 ltrs capacity of any type and brand of geyser.

(b) Supply only thermostat 0-70ºC suitable for geyser of 100 ltrs capacity of any type and brand of geyser. Make:As per the sample given by site-in-charge

(c) Supply only heating element of capacity 3 KW,ISI marked of any type and shape suitable for 100 ltrs capacity geysers of any brand / make. Make:As per the sample given by site-in-charge

(d) Supply only flow unit (inner pipe assembly) suitable for geyser of 100 ltrs capacity vertical type of any geyser brand including rubber ring/gasket.

M&L in replacement safety valve(dead weight) suitable for geyser of 100 ltrs capacity of any type and brand of geyser complete all as specified and directed.

M&L in replacement thermostat 0-70ºC suitable for geyser of 100 ltrs capacity of any type and brand of geyser complete all as specified and directed.. Make:As per the sample given by site-in-charge

M&L in replacement heating element of capacity 3 KW,ISI marked of any type and shape suitable for 100 ltrs capacity geysers of any brand / make. Make:As per the sample given by site-in-charge complete all as specified and directed.

M&L in replacement flow unit (inner pipe assembly) suitable for geyser of 100 ltrs capacity vertical type of any geyser brand including rubber ring/gasket.complete all as specified and directed.

Supply and fix in replacement GI mesh hot water connection 900 mm long including necessary washers suitable for geysers of various capacities complete all as specified and directed.

S&F in replacement sheet metal enclosures Single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, 240 volts complete with all accessaries etc all as directed

Supply & fix in replacement neon lamp indicator square/round type complete all as specified and directed.

Supply & Fix in replacement PVC insulated round cable 3 core stranded copper conductor 2.5 sqmm as in connection cord of the geyser complete with all accessaries etc all as directed

Supply and fix in replacement metal clad plug top 3 pin, 20 amps, ISI marked heavy duty complete all as specified and directed.

S&F in replacement plug top 3 pin, 15/16 amps, 230 volts, ISI marked complete all as specified and directed.

S&F in replacement plug top 3 pin, 5 amps, 230 volts, ISI marked complete all as specified and directed.

M&L in replacement of ply wood sheet of 10 mm thickness for Exhaust fans and cutting to the size as required at the site including fixing the same with necessary nuts and bolt arrangement complete all as specified and directed.

M&L for replacing the down rod of ceiling fans with 5 feet GI ceiling fan hanging down rod with necessary clamp accessories complete all as specified and directed.

M&L in replacement of acrylic sheet of 4mm thickness cutting to the size as required at the site including fixing the same with necessary screw arrangement complete all as specified and directed.

S&F in replacement PVC insulated cable 2 core stranded copper conductor 0.5 sqmm complete all as specified and directed.

S&F in replacement PVC insulated cable 2 core stranded copper conductor 1 sqmm complete all as specified and directed

S&F Picture light LED (warm white) fitting of 1x12 Watt individual LED lenses bronze coloured complete all as specified and directed. Make: Philips PHILIPS 919216000000 12W Picture Light, Bronze or equivalent makes as mentioned at makes list in PS

S&F in replacement of 1x10W,230V, LED batten suitable for indoor application of color temperature 6000K surface /wall mounted LED batten including connecting up with twin core twisted flexible copper conductor cable from ceiling rose complete all as specified and directed.

S&F in replacement 1x20 watt,230V surface and wall mounted emergency LED batten having backup upto 4 hours with polycarbonate housing and integrated electronic electronic driver including connecting up with twin core twisted flexible copper conductor cable from ceiling rose complete all as specified . Make: Luker LTGT520 or equivalent makes as mentioned at makes list in PS

S&F in replacement surface mounted LED Panel lights size of 600mm x 600MM x 35mm 40 W LED 5700K, 240Volts and glare free symmetrical illumination suitable for ceiling, Environmental friendly, new generation, energy saving, high power LED as a light source with clear diffuser and separate replaceable electronic driver including connecting with twin core wire and also matching to the adjacent ceiling surfaces carefully all as specified and directed. Note: The quoted price shall include the cost of Light and its driver. Make:Luker Cat part No. LNPSRS40 or equivalent makes as mentioned at makes list in PS

S&F in repalcement surface mounted LED Panel lights size of 1200mm x 300MM x 35mm 48 W LED 5700K, 240Volts and glare free symmetrical illumination suitable for ceiling, Environmental friendly, new generation, energy saving, high power LED as a light source with clear diffuser and separate replaceable electronic driver including connecting with twin core wire and also matching to the adjacent ceiling surfaces carefully all as specified and directed. Note: The quoted price shall include the cost of Light and its driver. Make:Luker Cat part No. LNPSRS48 or equivalent makes as mentioned at makes list in PS

S&F in replacement recess type LED ceiling lights 20 W LED with ceiling cut out of Ø 160 mm, 6000K Environmental friendly, energy saving, recess mounted downlighter with electronic driver including connecting with twin core wire, including cutting the existing false ceiling dia to the required size and also matching to the adjacent false ceiling surfaces carefully complete all as specified and directed. Make: Luker cat part no. LDR20 or equivalent makes as mentioned at makes list in PS

Material and labour of Aluminum composite panel sheets (ACP Cladding ) including 1/1.5mm aluminium pipe including necessary harware such as drilling iron screws, double tape, silicon dow, masking tape etc complete all as specified and directed by Engr-In-Charge.

S&F in replacement for white cover plate with frame 12 module.Make:As per the sample given complete all as specified and directed.

S&F in replacement for white cover plate with frame 8 module.Make:As per the sample given complete all as specified and directed.

S&F in replacement for white cover plate with frame 6 module.Make:As per the sample given complete all as specified and directed.

S&F in replacement for white cover plate with frame 4 module.Make:As per the sample given complete all as specified and directed.

S&F in replacement for white cover plate with frame 3 module. Make:As per the sample given complete all as specified and directed.

S&F in replacement for white cover plate with frame 2 module. Make:As per the sample given complete all as specified and directed.

S&F in replacement for white cover plate with frame 1 module. Make:As per the sample given complete all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 12 module complete all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 8 module complete all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 6 module complete all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 4 module complete all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 3 module complete all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 2 module complete all as specified and directed.

S& F in replacement PVC unbreakable surface boxes suitable for modular switches 1 module complete all as specified and directed.

Deccan Enterprises

SONU ENTERPRISES

Suchit constructions