PERIODICAL SERVICES, REPAIRS TO FLOORING JOINERY WATER PROOFING TREATMENT SUNKEN PORTION CERTAIN CIVIL WORKS TO MD OTM ACCN AND WELCOME MAINTENANCE TO OFFRS MD ACCN AT NAVAL STATION THANE UNDER GE (NW) MANKHURD

Amount

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:6) on fair faces of bricks or concrete surfaces, finished the surfaces even & smooth without using extra cement including 1mm thick sagol finish incl preparation of old surfaces in patches for repairs at any places inside the bldg complete all as specified.

M&L for rendering 20mm thick in cement mortar 1:4 on brick / stone masonry or concrete surfaces, on walls, laid in two layers, 1st layer 15mm thick and finishing layer 5mm thick mixed with integral water proofing compound @ 2% by weight of cement content of finishing layer, finished fair and even including all necessary scaffolding / staging as required complete all as specified and as directed.

M & L rendering 5mm thick in CM 1:3 on ceiling, soffit of staircase surfaces finished even and smooth without using extra cement with 1mm thick sagol finish, incl preparation of old surfaces in patches for repairs complete all as specified and dircted.

M& L for preparation of newly plastered surface of ceiling and applying three coat of white wash complete all as specified and directed

Chipping, removing carefully loose/damaged concrete incl plastering from RCC surfaces of columns, beams, soffits of slabs etc by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land, complete all as specified and directed. Note:- 1. Hard concrete shall not be removed by force. 2. Mode of measurement : Superfacial area of concrete will be measured.

M&L for cleaning existing reinforcement by sand blasting with suitable pump as directed by the GE and wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make Thermax/MAPEI/Fosroc/Sikru etc on rebars with time interval of 1 hr between the coats, complete all as specified and directed. Note :- Mode of measurement : superficial area of concrete will be measured.

M&L for Anticorrosive Treatment to Reinforcement using Corroseal - ZR of M/s Krishna Conchem or Epoxy Zinc Primer of M/s. Dr. Fixit or Thermax/MAPEI/Fosroc/Sikru etc by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces, complete all as specified and directed . Note:- Mode of measurement: superficial area of concrete will be measured.

M&L for providing mild steel TMT bars of any size or dia in various structural RCC elements like column, beams and Slab etc. including cutting, bending, fixing the bars, tying with binding wires etc. complete all as specified and directed. Note: This item is applicable for additional bars required in the existing RCC structures.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem or Thermax/MAPEI Construction/Fosroc as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from Thermax/MAPEI/Fosroc/Sikru etc while the bonding agent is still sticking upto 20mm thickness including levelling, profiling etc complete all as specified and directed.

M&L for building up the profile of structural members by using polymer modified mortar from Thermax/MAPEI/Fosroc/Sikru etc while the bonding agent is still sticking upto 40mm thickness including levelling, profiling etc in two layers, each layer not exceeding 20mm, complete all as specified and directed.

M & L for preparing old decorated surfaces of wall complete removal of existing treatment (plasterered or unplastered or previously white washed) & applying two coats of cement base paint over one coat of primer complete all as specified.

M& L for preparation of old plastered surface and applying one coat of white wash on ceiling.complete all as specified and directed

M & L preparing new surfaces of walls applying two coat of oil bound distemper over a one coat of primer complete all as specified & directed .

M & L for preparing old decorated surfaces of walls washing rubbing down & stopping of distempered & painted surfaces & applying one coat of oil bound distemper complete all as specified & directed.

M& L for preparation of new plaster/concrete surface of walls ,chajjas, soffits & beam including necessary scaffolding and applying two coats of 100% anti fungal acrylic exterior emulsion paint over a coat of primer including necessary scaffolding up to 24 m height, complete all as specified and directed.

M& L for preparation of old plaster/concrete surface of walls ,chajjas, soffits & beam including necessary scaffolding and applying one coat of 100% anti fungal acrylic exterior emulsion paint etc including necessary scaffolding up to 24 m height complete all as specified and directed

M&L for leakage / seepage proof coating consisting of preparing the surfaces of existing exterior walls, parapet walls, chajjas, etc. with wire brush to remove all loose dirt, oil grease, etc. and cutting and filling cracks above 5mm wide with Pidicrete URP of M/s Dr Fixit or with Plaster Seal of M/s STP Ltd or Thermax/MAPEI/Fosroc/Sikru etc and applying Primeseal primer of M/s Dr Fixit or equivalent chemical of M/s STP Ltd or one coat of Chemstick PDE 600 (and allowing to dry for 8hrs) under torch dry condition and subsequently applying two coats of water proofing decorative elastomeric coating system Raincoat with DFT 100microns of Shalicry 215 of M/s STP Ltd or Chemstik PDE 600 of equivalent of Thermax/MAPEI/Fosroc/Sikru etc (the surface after painting one coat shall be allowed to dry for 6 to 8hours before application of next coat) including necessary scaffolding to work at a height upto and including 24m complete all as per manufacturer instructions complete all as specified and as directed.

M & L preparation of old painted wooden surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

M&L Preparation of new or untreated painted wood and wooden based surfaces of any description not other wise described over 10 centimetre width or girth and applying Two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for special treatment of sunken portion of WCs and Bath room as per following stages: Stage 1 :- Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc. Stage 2:- Providing 15mm thick plaster in CM 1:3 mixed with water proffing chemical of Dr Fixit or Shalicrete "R' of STP Ltd or Thermax/MAPEI Construction/Fosroc in the proportion/quantity all as per manufacturer's instructions. Stage 3:- Primer-Mix Tarfelt LM of STP Ltd or Thermax/MAPEI Construction/Fosroc (diluted with water in ratio 1:1) @ 250 gms/Sqm and apply the Primer on the plastered suraces. Stage 4:- Application of 1st coat of Tarfelt LM of STP Ltd or Thermax/MAPEI Construction/Fosroc (without dilution with water) @ 1Kg/Sqm by brush all as per manufactuer's instructions. Stage 5:- Laying fibre glass cloth (weight not less than 50gram/ Sqm) over the 1st coat while the coated surface is still sticky. Stage 6. After 6 to 7 hours interval, apply second coat i.e. final coat of Tarfet LM of STP Ltd or Thermax/MAPEI Construction/Fosroc (without Dilution with water) @ 1kg/ Sqm by brush as per manufacturer's instructions. Stage 7:- Providing 10mm thick protective plaster in CM 1:3 mixed with STP No. 1 @ 250ml/50 Kg or Thermax/MAPEI Construction/Fosroc cement all as per manufacturer's instructions. Stage 8 :- Carryout ponding test for 48 hours to ensure water tightness of repaired sunken portion. NOTES : (i) Mode of measurement: Actual area treated (floor and adjoining walls) will be measured and paid (ii) The above treatment shall be got executed through applicator of manufacturer and necessary authenticated documents on account of above shall also be produced by the contractor.

M&L for filling of lean concrete 1:5:10 type E2 (Using 40mm graded stone aggregates) in sunken portion , as per requirement , complete all as specified and directed.

Dismantling / taking out any other existing water proofing treatment from roof including loosened cement plaster and exposing the top surface of RCC slab and removing rubbish, etc. to a distance exceeding 500 m and not exceeding 1.0 km complete all as specified and as directed by the Engineer-in-charge

M & L for APP modified roof treatment over roof slab etc to be executed through approved authorised applicator of the membrane manufacturer with the following specifications, complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160 gm/ Sq mtr using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20 degree celcius. (x) Dimentional stability % change = Maximum 1%. (d) Over the membrane provided a finishing with solar reflective bitumen aluminium paint @ 0.10 Kg/ Sqm as prescribed by manufacturer.

Demolition of plain cement concrete (unreinforced) in roofs and disposing off the rubbish to a distance exceeding 500m and not exceeding 1.0km complete all as specified and as directed by the Engineer-in-charge

M&L for cement concrete 1:2:4 (type B-0) using 12.5mm graded trap stone aggregates, as in roofs or kerbs, laid in proper slope, rounded or chamfered on edges including all necessary scaffolding or staging as required upto 24M height complete all as specified and as directed

S&F 100 mm size stainless steel medium weight hinge complete all as specified and directed.

S&F aluminum anodised barrel tower bolts of extruded section of size 150 mm length complete all as specified and directed.

S&F Aluminium handle, cast type anodized size of handle 150 mm complete all as specified and as directed.

S&F 250 mm length of bolt aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S & F door closer hydraulically regulated, aluminium extruded section body , designation No. 3 universal type, suitable for door shutters of weight between 61 to 80 Kg and width of door shutter 851 to 1000mm complete all as specified and directed

S&F floor door stopper aluminium alloy body over all length of cover plate 140 mm and tonque anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

M&L for Preparing surface of wood and wood based materials, steel and iron work, new or old of any description & girth, not otherwise described treating ends of posts with tar or coal tar black paint on back of chowkats area exc 0.10 Sqm but not exc 0.5 Sqm each complete all as specified and as directed.

M&L for Preparing surface of wood and wood based materials, steel and iron work, new or old of any description & girth, not otherwise described treating ends of posts with tar or coal tar black paint on back of chowkats area not exc 0.10 Sqm each complete all as specified and as directed.

S&F in repairs cabinet mirror of size 480 x 370 x 115 mm for superior quality sample approved by Garrison Engineer,complete all as specified

Taking down carefully existing aluminium sliding window shutters, taking down of existing broken 5 mm thick plain sheet glass from aluminium sliding window shutters including existing rubber gasket complete, supply and fixing 5 mm thick plain sheet glass with and including provision of new rubber gasket and re-fixing the shutters in existing position, complete all as specified and directed.

Taking down carefully existing aluminium sliding window shutters, taking down of existing stainless steel wire mesh from aluminium sliding window shutters including existing rubber gasket complete, supply and fixing stainless steel wire mesh of dia 0.36 mm and average width of aperture 1.40 mm with and including provision of "U" clip, re-fixing the shutters in existing position, complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) exceeding 1.5 Sqm but not exc 4 Sqm each including complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) not exceeding 1.5 Sqm each including complete all as specified and directed.

M&L PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in hold fast, bed plate etc including necessary form work complete all as specified and as directed.

S&F Mild steel work as in band, straps, supports for RWP, clamps, hold fasts, wall ties, , hooks & pintle hinges and similar small articles conforming to Fe-290-0 or Gde E-165 complete all as specified and directed.

S& F second class hard wood , plain ,soild ,straight chowkats and frames, wrought , rebated on soild rounded or chamfered , put together with gule pinned at joints etc complete all as specified .and directed

S & F IInd class hardwood 35mm thick plain framed, panelled shutters (any number of panel) with panels of timber flat on both sidess (feather edged) , or of veneered particle board medium density, wood particle board with commericial face veneers supplied and fitted to chowkats complete all as specified and directed.

S& F 35mm thick second class hard wood glazed and skelton shutters open rebated and prepared to receive glass, gauze, etc ( without sash bars), edges of framing plain, chamfered or rounded , fitted with cut and mitered beads for securing glass, etc size of members of shutters as specified & directed in SSR Part-I , section 8, clause 8.24 (a) complete all as specified and directed. Note :- Glass / wire mesh required will be measured and paid separately

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each complete all as specified and directed

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supply and fixing in opening as per specification given under SSR Part II 2010 including making good the disturbed surface all as specified and directed.

M&L for factory made solid PVC panel type PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2010 complete all as specified and directed.

Supply only 4.0 mm thick glass oridinary quality in each pane n exc 0.5 Sqm for aluminium sliding windows complete all as specified

Supply only stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed in aluminium windows complete all as directed.

Dismantling boarding any description fixed in any position with nails complete all as specified and directed .

S&F 18/19 mm thick interior grade prelaminated decorative choice lamination, & other side balancing white lamination, fixed with screws to timber frame work complete all as specified

S&F in repairs 150 mm length aluminum anodised barrel tower bolts of extruded section complete all as specified

S&F in repairs 300 mm in length Aluminium alloy , anodised , sliding door bolt with hasp, staple (bolt type ) and fixing clips of sheet , cast or exctruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified

S&F in repair 10 ltr, white coloured PVC, valveless, syphonic action type, flushing cistern, low level/ high level including inlet, ball valve, float and handle including brackets with and including PVC flush pipe 32 mm bore, connecting to WC etc, complete all as specified and directed.

Taking up or down 15mm dia bore steel tubing and connection including cleaning for refixing or removal to store complete all as specified & directed

All as per item No 57 above but 20mm dia bore steel tubing

S&F 15mm dia bore U-PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls , ceilings or in floors etc, with all fittings complete all as specified and as directed

Ditto all as per item No 59 above, but 20mm bore

S&F in repairs 15mm bore bib taps cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F in repairs 15mm bore stop valve cast copper alloy screwed high pressure with crutch or butterfly handle, screwed both end for iron pipe or for union complete all as specified & directed

S&F in repairs 15mm bore pillar taps,chromium plated, cast copper alloy with screwed down capstan head high pressure with or without lettered 'HOT' of 'COLD' crutch or butterfly handle, screwed both end for iron pipe or for union complete all as directed.

S&F in repair 110mm PVC(SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as directed.

All as per item no. 64 above, but 75mm bore

Supply only intergal water proofing compound. (ISI Marked).

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing the debris off the premises.

M & L for 20 mm thick in CM (1:6) screed bed or bedding layer for laying floor finishes complete all as specified and directed.

M& L for non skid coloured ceramic tiles 400mm x 400mm size and 7 to 8mm thick as in floor etc set and jointed in neat cement slurry and pointed with coloured cement to match all as specified and as directed

M&L coloured non skid ceramic tiles of size 300 x 300 x 6 to 7mm thick in floor etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed

M&L for coloured 300x200x6mm/350x250x7mm thick size glazed ceramic tiles in vertical surfaces such as skirting,dado etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick cement mortar backing coat in CM 1:4 etc, complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white and including plastic water closet seat cover as per reqd colour with flat bottom and cover and mild steel chromium plated or aluminium hinging device (excluding flushing cistern ) etc complete all as specified and directed..

S&F in repairs vitreous china squatting pan, white, orissa pattern pan of size 580 mm x 440 mm with integral foot rests setting and provision of concrete and including 'P' trap or 'S' Trap (excluding flushing cistern & flush pipe) complete including connection to trap and to flushing pipe, anti syphonic pipe etc., complete all as specifiedand directed.

S&F in repairs Vitreous China white, 1st quality, wash hand basin, flat back, size 550mm x 400mm including mild steel angle brackets,CP brass fittings, waste, union, 32mm dia PVC waste pipe, cutting for and pinning ends of brackets, complete all as specified and directed .

Dismntling of wall and ceiling boards (fibre,pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness including cover fillets any type complete all as specified and directed.

M & L for suspended false ceiling with aluminium grid work system of size 605x605mm with runners aluminium anodised main TEE of section 35x35x1.5mm thick , cross T of Section 25x25x1.5mm thick aluminium anodised angle of size 25mmx25mmx1.5mm thick fixed along side of wall with wooden plugs & hanging from ceiling MS purlins with and including 4mm dia GI wire suspension system (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40mmx3mm size, 60mm long and expansion hold fasteners 12.5mm dia 40mm long including provision of gypsum reinforcement board of size 600mmx600mmx8 to 10mm thick, make Armstrong or equivalent with necssary scaffoldind etc complete all as specified and directed. Note : A sum of Rs 11,325.00 towards sch of credit shall be deducted to arrive the contract sum

Atharva Enterprises

Biju Construction & Co

mp construction co

sapana enterprises

EVEREST POWER CONTROL ENGINEERS

Joy builders