Signaling work in connection with proposed construction of pedestrian subway in Kalyan-Igatpuri section related to safety fencing at various trespassing locations.

Item Breakup - A-SOR ITEM

Supply of Indoor Jumper Wire of various Kilometre colour as per Railways standard practice of type ATC 1 x 0.6 mm dia.conforming to IRS 76/89 (Amd.3) or latest.(Inspection Agency- Consignee)

Supply of PVC flexible copper cable single Kilometre core multistrand 1 x 25 Sq.mm (196 conductor each diameter 0.40 +/- 0.01) as per IS 2465/1984 & IS:694/2010 with latest amendment if any with insulation thickness of 1.2mm nominal conductor resistance 0.780 ohms/Km and test parameters are as per IRS (S)76/89 (Amd.3).(Inspection Agency- Consignee)

Supply of wire 16/0.2 (Blue, Red, Grey, Kilometre yellow, Brown, Black, White as per site engineer instruction) finolex/polycab/delton make. IRS S-76/89 (Amd.3), BS: 4808 Part-2. Wire to be procured from RDSO approved vender.(Inspection Agency-Consignee)

Supply of Battery Charger self regulating Numbers floor mounting type with 230 V AC single phase input and output 60 V DC, 20A as per spec. IRS.S.86/2000 (Amd.4) with latest amendments.(Inspection Agency-Consignee)

Supply of Battery Charger self regulating Numbers floor mounting type with 230 V AC single phase input and output 60 V DC, 40A as per spec. IRS.S.86/2000(Amd.4) with latest amendments.(Inspection Agency-Consignee)

Supply of Battery Charger self regulating Numbers floor mounting type with 230 V AC single phase input and output 24V DC, 20A as per spec. IRS.S.86/2000 with latest amendments for Axle counter applications (Amd.4). (Inspection Agency-Consignee)

Supply of Battery Charger self regulating Numbers floor mounting type with 230 V AC single phase input and output 24V DC, 30A as per spec. IRS.S.86/2000 (Amd.1) with latest amendments for Axle counter applications (Amd.4).(Inspection Agency-Consignee)

Supply of Point Chain Group Siemens make Numbers (No. RSSK 3515/3)or functional equivalent without base plates.(Inspection Agency- RDSO)

Supply of QNA1-K AC immunised relay, 8F- Numbers 8B, 24VDC along with plug board, retaining clip and connectors conforming to BRS:931A & RDSO letter no.STs/E/Relays/ UEA/PI dated 30.05.97 Annexure-II IRS:S60, IRS:S34 & IRS:S23. (Inspection Agency-RDSO)

Supply of QNA1-K AC immunised relay, 12F- Numbers 4B, 24VDC along with plug board, retaining clip and connectors conforming to BRS:931A & RDSO letter no.STs/E/Relays/ UEA/PI dated 30.05.97 Annexure-II IRS:S60,IRS:S34 & IRS:S23. (Inspection Agency-RDSO)

Supply of QNA1 AC immunised relay, 8F-8B, Numbers 24 VDC along with plug board, retaining clip and connectors confirming to BRS : 931A, IRS:S60, IRS:S34 & IRS:S23(Inspection Agency-RDSO)

Supply of QN1 Non AC immunised neutral Numbers relay, 8F-8B, 24 VDC along with plug board, retaining clip and connectors confirming to BRS : 930, IRS:S60, IRS:S34 & IRS:S23(Inspection Agency-RDSO) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Supply of QN1 Non AC immunised neutral Numbers relay, 12F-4B, 24 VDC along with plug board, retaining clip and connectors confirming to BRS : 930, IRS:S60, IRS:S34 & IRS:S23(Inspection Agency-RDSO)

Supply of QSPA1 relay, 24VDC, slow to pick Numbers up, 8F-4B, along with plug board, retaining clip and connectors conforming to BRS:933A, IRS : S60, IRS:S34 & IRS:S23(Inspection Agency-RDSO)

Supply of QBCA1 AC immunised relay, 2FHD Numbers 4F-4B,24VDC along with plug board, retaining clip and connectors conforming to BRS:943 POINT CONTACTOR RELAY and IRS S46. firms specification.(Inspection Agency- RDSO)

Supply of INDICATIVE TYPE OF FUSE Numbers INSERTS. IRS S:78-92 Without holder 1.6 A (System, Rapid or Malnad Make).(Inspection Agency-Consignee)

Supply of INDICATIVE TYPE OF FUSE Numbers INSERTS. IRS S:78-92 Without holder 0.6 A (System, Rapid or Malnad Make).(Inspection Agency-Consignee)

Supply of Main Signal Post 140 mm outer dia Numbers 4.6 Mtr Length as per spec No IRS S 6/81 with latest amendments.(Inspection Agency- Consignee)

Supply of Main Signal Post 140 mm outer dia Numbers 5.6 Mtr Length as per spec No IRS S 6/81 with latest amendments.(Inspection Agency- Consignee)

Supply of Shunt Signal Post with Base (GI Numbers Pipe of 80 mm Dia of min. 1 meter length.). (Inspection Agency-Consignee)

Supply of Cast Iron Main signal surface base Numbers 140mm as per spec No IRS S-10 and Drg No 2011/M with latest amendments, with CLS Ladder assembly complete for CLS signal 5.5/4.5/3.5 mtrs long as per RDSO Drg. No. SA-23156(Adv), SA-23153 (Adv) & SA-23150 (Adv) Alt. 1 respectively with Latest Amendment as the case may be for CLS unit & signal back staging as per extent C. Rly practice(Inspection Agency-Consignee)

Supply of Cast iron Shunt signal surface base Numbers 80 mm as per spec No.IRS S 10 and Drg No.2011/M with latest amendments, as per RDSO Drg No. SA-23156/Drg.No.RST/11413 as per extent C.Rly practice(Inspection Agency-Consignee)

Supply of Signal No.plates. as per Drg No Numbers RST-11393 / SK-842 or latest(Inspection Agency-Consignee)

OFF set bracket 5-1/2 " to suit 140 mm dia Numbers CLS Post with two no. of "U" Bolts with nut & washer complete as per RDSO Drg.No.SA- 23080 for Signals & Routes(Inspection Agency-Consignee)

OFF set bracket 3-1/2' for signals & routes. Numbers Drawing No. SA 23840 (Adv) Alt-2 as per extent C. Rly practice.(Inspection Agency- Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Supply of A/AG/C/P/G/IB Board as per Drg. Numbers RST-11444/1(A), RDSO Drg No SA 23460(AG), SA-23461( C), RST-11445. SA 23456(P), SA 23477(G) & SA 23476-77(IB) as applicable respectively with Latest Amendment.(Inspection Agency-Consignee)

Supply of Stop Board/IB Board as per RST- Numbers 11791 (STOP BOARD)/ RDSO Drg No.7235/B as per extent C.Rly practice.(Inspection Agency-Consignee)

Supply of different warning Boards as per Numbers Goods Warning Board (SK-784). RDSO Drg No. SA 2380 (Adv), SA 2370/M, Block section limit Board RDSO Drg.No. SA 2373 Paint and retroreflective arrangement as per Railways drawing.(Inspection Agency-Consignee)

Supply of Hand Cuff Locks/ Godrej Navtal Numbers lock with Three common keys.(Inspection Agency-Consignee)

Supply and Fixing of RE Protective Screens of Numbers expanded metal 12 SWG of size 1200 x 1500 mm on signals as per extant practice & as per instruction of Rly engineer at site. DRG.No.SK-844.(Inspection Agency- Consignee)

Supply of Phenolic 10mm thick sheet, grade Numbers P3 in standard size of 1.22X1.22 Mtr as per spec. No IS 2036 of 1995.(Inspection Agency- Consignee)

Supply of ARA Terminal blocks with links Numbers made of PBT Specn No.IRS/75/2006(Rev-2) with latest amendments and RDSO Drg.No.SA-23741A Alt.4, SA-23745 Alt.5, SA- 23746, SA-23748 Alt.4 & SA-23756A Alt.3. (Inspection Agency-Consignee)

Supply of cartridge fuse block made of PBT Numbers as per RDSO Drg No SA-23748 Alt 4, SA- 23749 & Spec No IRS S 75/2006 with latest amendment. Fuse block shall be suitable for round head type voltage fuses.(Inspection Agency-Consignee)

Supply of round head type non detoriating Numbers type low voltage cartridge fuse as per Specn No IRS/S/78/92 with latest amendments 2A/4A/6A capacity(Inspection Agency- Consignee)

Supply of Tik-tak, piano type switches,5 A (as Numbers per IS Specification).(Inspection Agency- Consignee)

Supply of three pole plug and socket 5 Amp Numbers (as per IS Specification).(Inspection Agency- Consignee)

Supply of Lamp 110V/24W, 2 Pin for Loc. Numbers (Inspection Agency-Consignee)

Supply of earth electrode assembly as per Numbers Drg.No. CR/S&T/SK-815(Inspection Agency- Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Supply of PVC jacketed wire rope for Track Metre Lead connections. PVC jacketed wire rope should be of Galvanised steel wire rope 6 mm dia (6x19 stranded wire with steel core of 6 mm dia) sheathed with PVC 2mm wall thickness, overall thickness being 10 mm. PVC sheath should be made of type 6 compound as per IS 5831 of 1984 Reaffirmed 2001 and steel wire rope as per IS: 2266:2019. Reclaimed or recycled material should not be used.(Inspection Agency- Consignee)

Supply of Pre-wired Crank Handle cum key Numbers lock relay box (of metal) alongwith LEDs, with approved type push buttons, 8-way terminal strips, string rod, etc. as per Drawing No.RST.C.114(Inspection Agency- Consignee)

Supply of GI pipe, inner dia. 100mm dia. B- Metre class as per spec. No.IS 1239 PT. 1/2004 or l a t e s t with sockets and fittings. TATA/JINDAL/ZENITH BIRLA make.(Inspection Agency-Consignee)

Supply of DWC HDPE pipe with one snap fit Metre coupler and 'O' ring fire resistant, anti rodent, in 6 meter length of size 120 mm outer dia as per RDSO/SPN/204/2011 Ver. 1.1 with Amd.1 or latest.(Inspection Agency- Consignee)

Supply of RCC pipes half round of size Numbers 150mm dia outer and 100 mm dia internal 1 mtr long matching to IS No. 458/2003 amendment-1 with Rev.4.(Inspection Agency-Consignee) Total 3765982.63

Item Breakup - B-SOR ITEM

Excavation and Casting of Main signal Numbers foundation as per Drg No SK 801 with contractor's own materials including cement and anchor bolts of standard size. The required scaffolding Ferma etc for Casting of foundation will have to be brought by the contractor at his own cost.(Inspection Agency-Consignee)

Excavation and Casting of Shunt signal Numbers foundation as per Drg No SK 802 with contractor's own materials including cement and anchor bolts of standard size. The required scaffolding Ferma etc for Casting of foundation will have to be brought by the contractor at his own cost.(Inspection Agency-Consignee)

Erection of CLS Post with Surface base and Numbers signal unit on top or on OFF set Bracket, fixing of front and back staging, ladder and guards, signal name plates/boards if any with contractors own brackets and fixing materials. This also includes erection of auxiliary signals like calling on, shunt signal if any. The work shall be done as per instructions of Rly engineer at site. (Inspection Agency-Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Erection of shunt signal with Surface Base, Numbers Post, Signal unit and fixing of No.plates. The work shall be done as per instructions of Rly engineer at site. (Inspection Agency- Consignee)

Fixing of Jn.Route Indication 1-Way/2-Way/3- Numbers Way on the top of the signal post.(Inspection Agency-Consignee)

Fixing of Stop Board, Block section limit Numbers Board, goods warning board with contractors own material. The work shall be done as per instruction of Rly engineer at site.(Inspection Agency-Consignee)

Termination of tail cable on Main signal units Numbers and wiring with contractor own material, etc. The work shall be done as per instruction of Rly engineer at site.(Inspection Agency- Consignee)

Termination of tail cable on Shunt signal Numbers units and wiring with contractor own material, etc. The work shall be done as per instruction of Rly engineer at site.(Inspection Agency-Consignee)

Hot dip Galvanizing as per RDSO Specn. ETI- Kg OHE-13 [4/84] - Signal post, OFF Set Brackets dia 140mm and length upto 5600 mm. (Inspection Agency-Consignee)

Installation of ON/OFF aspect LED's in signal Numbers including termination of tail cable on signal, wiring, fixing of LED units and testing. The work shall be done as per instruction of Railway Engineer at site.(Inspection Agency- Consignee)

Fabrication laminated/Fibre glass sheet in location box by providing all fixtures as per Railway Drawing including fixing of PVC coated/with PVC pipe covered string rods at the back side for cable support with contractor's own materials. The work shall be done as per drg and arrangement similar to SK 783-1&2. with latest alterations & as per instructions of Rly engineer at site.Single Case(Inspection Agency-Consignee)

Fabrication laminated/Fibre glass sheet in location box by providing all fixtures as per Railway Drawing including fixing of PVC coated/with PVC pipe covered string rods at the back side for cable support with contractor's own materials. The work shall be done as per drg and arrangement similar to SK 783-1&2. with latest alterations & as per instructions of Rly engineer at site.Half Case(Inspection Agency- Consignee)

Fixing of cutting in relay bases & wiring of Numbers relays with Contractors own material obtained from approved sources in location box as per the instuctions of Engineer in charge.(Inspection Agency-Consignee)

Fixing of ARA Terminals and fuse blocks on Per phenolic laminated sheets and fixing by Conductor stainless steel/brass nuts & bolts.This includes provision of two additional holes on the board on either side for cable conductor entry. (Inspection Agency-Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Termination of cable cores on ARA Per terminal/fuse blocks in the apparatus Cases/ Conductor cable termination rack.This includes all associated works of pulling out the cable from underground. The work shall be done as per location plans and instructions of Rly engineer at site.(Inspection Agency- Consignee)

Excavation and Casting of Apparatus Case Numbers foundation with contractors Anchor bolts, cement, ballast and other materials. The required scaffolding Ferma etc for Casting of foundation will have to be brought by the contractor at his own cost.Single Case as per Drg No . SK-803(Inspection Agency- Consignee)

Excavation and Casting of Apparatus Case Numbers foundation with contractors Anchor bolts, cement, ballast and other materials. The required scaffolding Ferma etc for Casting of foundation will have to be brought by the contractor at his own cost.Half Case as per Drg No . SK-804(Inspection Agency- Consignee)

Erection of Apparatus Cases. This includes Numbers filling of location foundations and plastering Single Case (Inspection Agency-Consignee)

Erection of Apparatus Cases. This includes Numbers filling of location foundations and plastering Half Case (Inspection Agency-Consignee)

Installation of Eqpt. (Relays, resistance, Numbers chargers batteries etc.as applicable) & wiring of the same in apparatus Cases as per location diagrams & circuit diagrams, as per Instruction of site incharge and practice.Single Case (Inspection Agency- Consignee)

Installation of Eqpt. (Relays, resistance, Numbers chargers batteries etc.as applicable) & wiring of the same in apparatus Cases as per location diagrams & circuit diagrams, as per Instruction of site incharge and practice.Half Case (Inspection Agency-Consignee)

Installation of earth electrode assenbly as Numbers per Drg.No.RE/S&T/SIG/Tender/SK726/85 including earth wire connected through GI wire 8 SWG supported on M.S. flat of size 6mm x 40 mm to earth electrode as per drg. No. CR/S&T/SK-815 for sigg. Equipment such as lever frames, apparatus case, signals, relay racks,block insruments, and etc. as per RE manual. The earth value should be less than 10 Ohms including the lead wire. The value should be measured in presence of Rly. supervisor. It should be documented and painted on earth enclosure made of concrete.( only earth electrode will be supplied by Railway). All other material required for provision of earthing will be brought by the contractor. (Inspection Agency-Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

"Excavation of cable trench as per cable cum route plan,1.0 mt. deep and 300mm wide along side the track in normal soil/strata, conforming to distances as per cable route plan and refilling after cable laying. This work includes covering of cable laid in trench by loose soil for a layer of 50mm thickness after clearing of route,bushes etc. It shall be ensured that top of the cables laid is at a depth of 0.8m or more. It if is less, then the width and depth shall be suitably increased and accordingly proportionate payment shall be made. In case depth of trench is not achievable due to site conditions proportionate payment will be made as per procedure. The work shall be done as per the extant practice on Central Railway and instructions of Railway Engineer at site. Drg. No. SK 805 (Inspection Agency-Consignee)"

"Excavation of cable trench as per cable cum route plan,1.0 mt. deep and 300mm wide along side the track in hard soil, conforming to distances as per cable route plan and refilling after cable laying. This work includes covering of cable laid in trench by loose soil for a layer of 50mm thickness after clearing of route,bushes etc. It shall be ensured that top of the cables laid is at a depth of 0.8m or more. If it is less, then the width and depth shall be suitably increased and accordingly proportionate payment shall be made. In case depth of trench is not achievable due to site conditions proportionate payment will be made as per procedure. The work shall be done as per the extant practice on Central Railway and instructions of Railway Engineer at site. Drg. No. SK 805 (Inspection Agency- Consignee)"

Fixing of GI pipes for crossing the culverts, Metre bridges etc. and concreting of ends with brick masonry at both ends as per the instruction of Rly engineer at site. (Inspection Agency-Consignee)

Digging of trench 1.0 M deep from rail cum flange/road level (for LC) and 0.3Mtrs. to 0.6 Mtrs wide and back filling after placing of DWC/RCC/GI pipe.(Placing of DWC/RCC/GI pipe covered separately. The ballast disturbed be screened and dressed as required by Engineer-in-charge or his representatives and road tarred immediately. Drg. No. SK 806 (Inspection Agency- Consignee)

Laying collars/RCC Half round pipes in trenches at places of track and road crossings, platform cuttings etc. (Inspection Agency-Consignee)

Laying of signalling/Power/Telecom cable of Kilometre various cores/sizes in trenches. (Inspection Agency-Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

"Horizontal boring of cable duct of minimum Metre 2.0 Mtr. depth alongwith laying of 120mm HDPE pipe for track crossing with minimum depth reckoned from the bottom of the rail/road crossing with minimum depth reckoned from ground level. The work shall be done as per extant practice & instructions of site Engineer. Prepration of site for Horizondal boring shall be carried out in presence of Railway Representative. HDPE will be supplied by Railways. Note:- Contractor shall provide all material required for boring and adequate nos. of labours for proper laying of cables into the bore. Cable shall be laid cautiously so that it should not get damage due to rough handling & pressure on cable. (Inspection Agency- Consignee)"

"Painting of two coats of synthetic enamel Numbers paint over one coat of primer on the following after scraping & cleaning surface wherever necessary with contractor' own supply of paints.Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge.Epoxy paint will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer. Apparatus Case Full Size. (Inspection Agency-Consignee)"

"Painting of two coats of synthetic enamel Numbers paint over one coat of primer on the following after scraping & cleaning surface wherever necessary with contractor' own supply of paints.Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge.Epoxy paint will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer. Apparatus case Half Size. (Inspection Agency-Consignee)"

"Painting of two coats of synthetic enamel Numbers paint over one coat of primer on the following after scraping & cleaning surface wherever necessary with contractor' own supply of paints.Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge.Epoxy paint will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer. Main Signal Post with Signal Units, Surface base and complete fittings as per Central Railways standard practice. (Inspection Agency-Consignee)" MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

"Painting of two coats of synthetic enamel Numbers paint over one coat of primer on the following after scraping & cleaning surface wherever necessary with contractor' own supply of paints.Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge.Epoxy paint will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer. Shunt signal post with signal unit, surface base as per Central Railway's Standard Practice.(Inspection Agency- Consignee)"

"Painting of two coats of synthetic enamel Numbers paint over one coat of primer on the following after scraping & cleaning surface wherever necessary with contractor' own supply of paints.Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge.Epoxy paint will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.Track lead Junction Box. (Black enamel outside only)(Inspection Agency- Consignee)"

"Painting of two coats of synthetic enamel Numbers paint over one coat of primer on the following after scraping & cleaning surface wherever necessary with contractor' own supply of paints.Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge.Epoxy paint will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer. Point Machine with ground connections complete (Point Machine with Black enamel only outside and ground connections with Red Oxide)(Inspection Agency-Consignee)"

"Painting of two coats of synthetic enamel Numbers paint over one coat of primer on the following after scraping & cleaning surface wherever necessary with contractor' own supply of paints.Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge.Epoxy paint will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.Axle Counter devices. (Inspection Agency-Consignee)" MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Lettering / Numbering of Signals, Point Numbers Machine, Track Lead Junction Boxes, Block Joints, Apparatus Cases etc. (each item to be taken as One Unit) This work will be carried out as per the standard practice being followed in Central Railway.(Inspection Agency-Consignee) Total 1812212.53

Item Breakup - C-NON SOR ITEM

Supply of cable route marker as per Numbers RST/C/203 of FRP(Inspection Agency- Consignee)

Supply of DWC/HDPE pipe with one snap fit Metre coupler 'O' ring confirming to IS 14930 (Part 2: 2001) Non metallic, normal duty, pliable with protection against chemical attack and fire resistant, anti rodent, in 6 meter length of size 50 mm inner dia.(Inspection Agency- Consignee)

Supply of Wheel sensor with 5 mtr moulded Numbers cable 60 Kg compatible with existing Frauscher MSDAC as per RDSO specification no. RDSO/SPN/176/2013 (Version 3) or latest. (Inspection Agency-RDSO)

Wheel sensor with protection tube of Numbers Frauscher make MSDAC type Rsr 180 (with BBIK- M 12 GS05 fixing along with cable length of 10 mtr (GS05)(Inspection Agency- RDSO)

Wheel sensor with protection tube of Numbers Frauscher make MSDAC type Rsr 180 (with BBIK- M 12 GS05 fixing along with cable length of 15 mtr (GS05)(Inspection Agency- RDSO)

Supply of MSDAC spares of FRAUSCHER Numbers make Over voltage protection board BS1004 (Version-GS01 Part no.18571) as per RDSO specification no. RDSO/SPN/176/2013 Ver 3.0 or latest (Inspection Agency-RDSO)

"Supply of RESET BOX CARD Compatible with Numbers existing FRAUSCHER make MSDAC as per RDSO Specification No. RDSO/SPN/176/2013 (Version.3) or latest.(Inspection Agency- RDSO)"

Supply of Communication Board compatible Numbers with existing Frauscher make MSDAC as per RDSO specification no. RDSO/SPN/176/2013 (Version 3) or latest(Inspection Agency- RDSO)

Supply of input/output board IO-EXB Numbers compatible with existing Frauscher make MSDAC (FAdC) as per RDSO specification no. RDSO/SPN/176/2013 (Version 3)(Inspection Agency-RDSO)

Axle counting board ACB 120 type for Numbers Frauscher MSDAC system(Inspection Agency- RDSO)

Supply of Evaluation Board AEB 101 for Numbers MSDAC system for Frauscher make. (Inspection Agency-RDSO)

Supply of counting head ZP D 43 complete Numbers with sensor for Siemens make MSDAC(Inspection Agency-RDSO) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Wheel detection sensor with 10 meter cable Numbers for SiemensMSDAC(Inspection Agency-RDSO)

Supply of MSDAC Spares - Siemens Make TX- Numbers RX Coil 5Mtrs.(Inspection Agency-RDSO)

Serial I/O card for Eldyne make Multi section Numbers Digital Axle Counter MSDAC as per RDSO/SPN/176/2013 Ver.3 or latest. Make Thals C/o Eldyne. Make Eldyne Elcetro System Pvt. Ltd. (Inspection Agency-RDSO)

Parallel I/O card for Eldyne make Multi Numbers section Digital Axle Counter MSDAC as per RDSO/SPN/176/2013 Ver.3 or latest. Make Thals C/o Eldyne. Make Eldyne Elcetro System Pvt. Ltd. Part No should as 3CR01893PEBB(Inspection Agency-RDSO)

PDCU for Multi section digital axle counter Numbers (MSDAC) as per RDSO/SPN/176/2005 Make Eldyne electro System Pvt. Ltd. (Inspection Agency-RDSO)

Supply of Analog card (AzLM) for Eldyne Numbers make Multi section digital Axle counter (MSDAC) as per RDSO/SPN/176/2013 or latest (Inspection Agency-RDSO)

Motherboard 3CRo1838AAAA make Eldyne(Inspection Agency-RDSO)

Track side Electronic Unit (EAK) for MSDAC Numbers as per RDSO Spec No.: RDSO/SPN/176/2013 Ver.-3 Make:ELDYNE only.(Inspection Agency-RDSO)

Supply of spares ISDN Card for Eldyne Multi Numbers Section Digital Axle Counter (MSDAC) as per RDSO/SPN/176/2005 or latest make Thales C/o Eldyne. Make Eldyne Electro System Pvt Ltd. Supply of Spares of ISDN CARD FOR ELDYNE MULTI SECTION DIGITAL AXLE COUNTER MSDAC AS PER RDSO/SPN/176/2005 OR LATEST MAKE THALES C/O ELDYNE .MAKE ELDYNE ELECTRO SYSTEM PVT LTD.(Inspection Agency-RDSO)

SK 30H double rail contact with 8 meter Numbers cable for Eldyne make Multi/Single section Digital axle counter as per RDSO specification no.RDSO/SPN/176/2013 ver.3 or latest and manufacturer specification. Make Eldyne electro systems Pvt.Ltd. (One no.packet contains the 02 no.TX and 02 nos RX Coils for rail connection sufficient for 1 DP including all accessories) MAKE THALES/ELDYNE(Inspection Agency-RDSO)

Set of SK 30H double rail contact with 5.5 Metre meter Cable for Multisection Digital Axle Counter, ( MSDAC) as per RDSO Spec. No. RDSO/SPN/176/2013 Make/ Eldyne Electro- systems Pvt Ltd. Version 3(Inspection Agency-RDSO)

Set of SK 30H double rail contact with 4 mtr, Metre integral cable for MSDAC suitable for Eldyne make as per RDSO Spec. No. RDSO/SPN/176/2013 Ver-3. Make/ Brand : Thales/Eldyne Electro-systems Pvt Ltd. (Inspection Agency-RDSO)

Digital Card for SSDAC, Eldyne make part no Numbers 3CR31010PFAA, Make: Eldyne Electrosystems Pvt. Ltd.(Inspection Agency- RDSO)(Inspection Agency-RDSO) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Supply of DC clampmeter FLUKE/AMPROBE Numbers AC/DC low current model LH-41 or similar(Inspection Agency-Consignee)

Supply programmable static switching module of Naturally air-cooled only with an at a glance LCD display suitable for break-less switching between two DC supplies of upto 40 A for 20- 110 VDC . (Inspection Agency-RITES)

Installation programmable static switching module of Naturally air-cooled only with an at a glance LCD display suitable for break-less switching between two DC supplies of upto 40 A for 20- 110 VDC . (Cable by Railways)(Inspection Agency-Consignee)

Bumpless Automatic power source change Numbers over Device DC -20V-150V, 45 A (2 input sources) Model no. PT-RSA-HL-DC- 03(Inspection Agency-Consignee)

Supply of "Calling On" Signal Unit in Numbers Alluminium body without lenses and transformers complete and to suit LED sigal Lamps.(Inspection Agency-Consignee)

Supply of copper lugs 25 Sq.mm double hole Numbers for AFTC track lead (Rail side) as per Drg.No. R-ST 11788 make Braco.Dowells,Shakti , Ascon.(Sample to be approved before bulk supply).(Inspection Agency-Consignee)

Supply of DPM meter (DC measurements) Numbers range 0 to 200V DC operating on 230V AC auxillary suply equivalentto MECO/Rishi or similar.(Inspection Agency-Consignee)

"Copper lug 25 Sq.mm Single Hole TU Side Numbers for AFTC track lead make Dowells , Braco, Shakti make. MAKE :BARCO.(Inspection Agency-Consignee)"

"12V 42AH LEAD ACID SMF BATTERY (GEM Numbers OFFER EXIDE 12.0 Volt Volt Lead Acid Battery (EXIDE) Model | Exide Power safe Plus EP 42-12 AS PER GEM CONTRACT) (Inspection Agency-Consignee)"

Supply of Copper LUG 6/10/16 Sq mm Numbers Dowells,ASCON,Jainson only.(Inspection Agency-Consignee)

Galvanised square Headed Bolt Nut 19 mm Numbers dia 100 mm length full threaded the material shall be of steel T -10 (Inspection Agency- Consignee)

"Set of glass fuses size: 5 X 20 mm, 250 V AC Numbers fast acting glass body with nickel plating, brass cap cartridge fuse conforming to IEC specification No. 60127- 2, consisting of (1) 250 MA glass fuse = 50 Nos. per set. (2) 1 amp glass fuse = 50 Nos. per set. (3) 2 amps glass fuse = 50 Nos. (4) 3 amps glass fuse = 50 Nos. (5) 4 amps glass fuse = 38 Nos. (6) 10 amps glass fuse = 37 Nos. (One set consists of total 275 Nos.) Brand: WICKMANN / RS / FERRAZ / WAGO(Inspection Agency- Consignee)

Supply of GLF Tape Abration resistance with Numbers masting compound in size of 51 mm x 1.27mm x 2.6 Mtrs Rolls of Stanvac Chemicals, Permacel, ICC, Nitco or 3 M make. (Inspection Agency-Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

G Type Fuse Holder 25A with 10 Amp Fuse Numbers Link ( Bottle type) Make- Viral,Bharat or Linder only(Inspection Agency-Consignee)

"FUSE HRC PORCELAIN COMPLETE ASSLY. Numbers WITH FUSE BASE FOR FRONT CONNECTION, FUSE LINK 6 AMPS. 500 VAC [QUICK ACTION DUTY TYPE D-II WITH ALTERNATIVE SHAPE] FUSE CARRIER GAUGE PIECE AND COLLER RING TO IS:8187 OF 1976 C and D NO. 5111/F341/664. EACH UNIT SHOULD BE EMBOSS/ENGRAVED WITH MAKERS NAME, (Inspection Agency-Consignee)"

"D type Fuse complete set with base & Numbers h o l d e r 2A,4A,6A, 10A,16A,25A (Inspection Agency-Consignee)"

Panel push button for Siemen%u2019s signal Numbers panel with contact making assembly of various colour Red, Grey, Blue, Yellow & Blue white dot complete. Consisting of colour Red- 50, Blue-50 , Blue with white dot-50, Grey-50, Yellow-50, GREEN-50.(Inspection Agency- Consignee)

Supply & commissioning of Thermo vision Numbers imager alongwith drive & power tools & equipments spares as per RDSO's specn. No. TI/SPC/OHE/TIPS/1030(6/2005) REV-1 or latest(Inspection Agency-Consignee)

Digital infrared thermometer (temperature Numbers gun) with data logger as per details mentioned in annexure A make/brand: KUSUM MECO/ Fluke 568/ METRAVI VIT-20 OR any superior make HTC IRX 67 or equivalent. (Inspection Agency-Consignee)

Digital current clamp meter to measure Numbers current leaks parasitic draws down to 1 mA and electric load from 1 mA to 100 Amp AC/DC, and voltages from 0 to 600 V AC/DC, small jaw size to measure current in signaling circuits, 4 digit display. make FLUKE/ GTC/KIOCO or superior with better specification mentioned with all accessories like test lead, batteries and carrying case, sample may got approved from consignee before supply. (Inspection Agency- Consignee)

Supply of Frequency Selective Voltmetre, Numbers APLAB make Model No. FSV-02 or similar. (Inspection Agency-Consignee)

"VENUS ADJUSTABLE SPANNER 15"" /375MM Numbers PHOSPHATE FINNISH (Venus) Cast Iron conforming to Grade BM 310 of IS :2108- 1977 (for light duty wrenches) preferably Drop Forged, Maximum opening of adjustable jaw (min 36 mm to 41 mm) + Tolerance(3 mm) make Taparia, VENUS, JK. (INDER Normal duty Type A Phosphate Coating Adjustable single ended open jaw wrench .(Inspection Agency-Consignee)"

Battrey oprated drill m/c cutter 22.5 mm Rail Numbers TCT Cutter 22.5x 55 mm (Part No: 240289) (Inspection Agency-Consignee)

BATTERY CHARGER , RIPPLE FREE,230V Numbers AC/24V DC, 20AMP SUITABLE FOR AXLE COUNTER APPLICATION IN RAILWAY(Inspection Agency-Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

"Battery Charger self regulating floor Numbers mounting type with 230 V AC single phase input and output 60 V DC, 20A as per spec. IRS.S.86/2000 (Amd.4) with latest amendments for Axle counter applications(Inspection Agency-Consignee)"

Digital frequency selective voltmeter for Numbers measuring the voltages at all the frequencies of Siemens mk AFTC (model-Fsv o2,.KTS/01 or similar, Make-Siemens ,Aplab or Kaynes or similar) (Inspection Agency-Consignee)

Key lock relay with 1 no, K 50 (AC Numbers Immunised) relay to work on 60 V DC with 1 ward and key make siemens with case contact configuration 5F/3B, Make siemens (Inspection Agency-Consignee)

"NYLON INSULATED BLOCK JOINT SET FOR 52 Set KGS. Rails as per specifications IRS/S/40/84 with latest amendments,RDSO ASSEMBLY drawing No SA-22101(Adv) with latest alterations and each set consisting of parts as under (A) SIDE CHANNEL Plate/drg.No. S- 22103(Adv)/Latest alteration -Qty-4NOS.(B) END POSTdrg no./S-22105(Adv)/Latest alteration qty--1NO.(C)INSULATION PLATEdrg no.S-22106(Adv)/Latest alteration qty -4NOS. (D)Insulating BUSH drg no.S- 22109(Adv)/Latest alteration qty--8NOS. (Inspection Agency-Consignee)"

Supply of HSS straight shank jobber Drill Numbers ground flute to IS 5101/DIN 338/ BS 328 ISO of size 7.1 mm of Addison, JK make of similar(Inspection Agency-Consignee)

Supply of straigt shank twist drill jobber size Numbers 13 mm of make Addison, JK as per IS 5099/1983 for material & hardness (Inspection Agency-Consignee)

Twist Drill Size 13x19 mm L (Part No: Numbers 5223118)(Inspection Agency-Consignee)

VDU screen industrial grade- 43'(Inspection Numbers Agency-Consignee)

"Arrangement of Battery operated Rail Core Numbers Drill alongwith additional 18 mm TCT Rail Core Drill , Maximum core cutting capacity : 36 mm, Rated speed: 250/450 RPM, Battery type: Li-on, Battery voltage: 50 Volt, Battery pack capacity: 4 AH, Number of Battery supplied: 2 Nos, Number of Charger supplied: 1 No, Special design pressurized Internal spindle cooling to give maximum life of core cutter and to avoid heating of the rail. Time taken to drill one hole of 32 mm in 60 KG 90 UTS rail section less than one minute. Time taken to fix the machine on the rail, less than 2 minutes and to de-clamp less than 1 minute. 34 Number 32 mm diameter hole with full charge batteries (17 hole per battery) in 60 Kg 90 UTS rail section. 3 Sets of standard center rail drilling adapters for gauge 90, 52, 49 provided along with machine. Weight of machine with battery: 18.5 KG, Make: Eibenstock. Bosch, KPTL(Inspection Agency-Consignee)" MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Battery operated High performance LED area Numbers with 3000 lumens output light weight & unbreakable as per specification attached (1) Product specification M18 HAL -+ M18 NRG 502B (2) Article No. 493345123 (3) Battery compatibility all Milwaukee M18 Batteries (4) Battery capacity (Ah) 5.0 (5) Battery type Li ion (6) No of Battery charger supplied 01 No. (7) Full Battey charging time 59 min (8) Max light output 3000/1500/650 (9) Max run time battery 2/4/9 hr. (10) No. of batteries supplied 2 Nos. (11) Voltage (AC) (V) 220- 240 (12) Voltage (DC) (V) 18 (13 Wight with battery pack (kg) 3 (14) One year onsite warranty, installation & training free of cost mak Eibenstock/Milwaukee or equivalent.

Analog Megger 500 V, 0-1000 Mega Ohm, Numbers Metal Body, Hand Operated, Supplied with Leads Test and Calibration Certificate with Minimum 1 Year Warranty Make : PICO/MEGGER/MICO (Inspection Agency- Consignee)

SUPPLY OF 8-WAY TERMINAL STRIPS, MADE Numbers OF PBT,ISOLATING BARRIER TYPE AS PER IRS-S-79/92(AMD.2) & DRG NO SA24811 WITH LATEST AMENDMENT.(Inspection Agency-Consignee)

"Program Switches, snap action base Numbers mounting type along with cover and mounting bracket 63 A-7 Pole 3 position Siemens type (3 LAO-63/7Y)/L&T/HAVELLS type .Drg.No.RST.C.106(Inspection Agency- Consignee)"

"Retro Reflective Sheet Yellow Colour. Make- Square 3M of USA/REFLOMAX of SOUTH Foot KOREA/ORAFOL of GERMANY). (Sample suitability of board should be verified before receiving the full qty. of supply)(Inspection Agency-Consignee)"

"Set of Tools, one set consisting of 07 items. Set (1) Tubular Box Spanner, Conforming to IS 2030 - 1989, Size - 8x9 mm. Make - De Neers or Venus or Jhalani, Qty. 50 nos. (2) Tubular Box Spanner, Conforming to IS 2030 - 1989, Size - 10x11 mm. Make - De Neers or Venus or Jhalani, Qty. 50 nos. (3) Tubular Box Spanner, Conforming to IS 2030 - 1989, Size - 12x13 mm. Make - De Neers or Venus or Jhalani, Qty. 50 nos. (4) Single - Ended, Open - Jaw, Adjustable Wrench, Conforming to IS: 6149 - 1984, Size - 250 mm. Make - De Neers or Venus or Jhalani, Qty. 30 nos. (5) Single - Ended, Open - Jaw, Adjustable Wrench, Conforming to IS: 6149 - 1984, Size - 300 mm. Make - De Neers or Venus or Jhalani, Qty. 30 nos. (6) Single - Ended, Open - Jaw, Adjustable Wrench, Conforming to IS: 6149 - 1984, Size - 200 mm. Make - De Neers or Venus or Jhalani, Qty. 30 nos. (7) Heavy Duty Pipe Wrench, Conforming to IS: 4003 (Part II) 1986, Size - 200 mm. Make - De Neers or Venus or Jhalani, Qty. 50 nos.(Inspection Agency-Consignee)"

Supply of DWC/HDPE pipe with one snap fit Metre coupler 'O' ring confirming to IS 14930 (Part 2: 2001) Non metallic, normal duty, pliable with protection against chemical attack and fire resistant, anti rodent, in 6 meter length of size 50 mm inner dia.(Inspection Agency- Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Repairing of location foundation with Numbers masonary work. This also includes cleaning the locations, sand filling in the location and plastering inside the location(Inspection Agency-Consignee)

Execution of S & T work related to Job enginnering /Signalling block of CTR/TTR/TSR or others, in one block, five unskilled manpower have to be provided during block for S&T connection removing & refixing as per Railway site engineer instruction. (Inspection Agency-Consignee)

Casting of cement concrete to protect S&T cum equipments and laid cables, above pipes, Signal store etc by concrete mixture of cement, sand, stone in the ratio of 1:2:4 using 25 mm graded stone aggregate as per instruction of site in charge of railways. Concrete is to be casted with the help of suitable size shuttering form as per site requirement. Concrete is to be cured for sufficient time as per standard practices on railways(Inspection Agency-Consignee)

Frequency Converter Input 230 V AC Numbers (plus/minus 20%) Single Phase 50 Hz Output (i) 110 V AC & 83.3 Hz Frequency and (ii) 165-190 V AC & 83.3 Hz Frequency Capacity 3 KVA make Reliance, DB & Siemens. (Inspection Agency-Consignee)

Supply of Design set for circuits as per Set Annexure XVII(Inspection Agency-Consignee)

Supply of CPU card suitable for UFSBI as per Numbers specification no. IRS : S- 105/2012 Ver 0 or latest(Inspection Agency-RDSO)

Supply of Secondary Modem for UFSBI Numbers Deltron make (For use with secondary media OFC /EI) as per specification IRS : S-105/2012 Ver ) or latest(Inspection Agency-RDSO)

SUPPLY OF MOTHERBOARD WITH 6U RACK Numbers FITTED COMPATIBLE WITH DELTRON MAKE USFBI SYSTEM as per specification no IRS:S- 105/2012 version or latest.(Inspection Agency-Consignee) Total 25541498.91