Construction of Integrated Public Health Laboratory at Sadar Hospital Bokaro.

Amount

PUFF PENALING & S.S WORK Supply, installation, testing and commissioning of modular OT Wall and corner panels with insulated prefabricated puff Panels. The OT wall shall be constructed using GI puff panels having 0.8 mm thick GI sheets on both sides. These panels should have been produced in a double band laminator, in which two continuously moving belts carrying 120 GSM galvanized steel sheets of 0.80 mm thickness are firmly bonded together by sprayed -in insulating foam, which hardens during the process. The core consists of rigid polyurethane foam, which has been injected under high pressure, with a minimum density of 40kg/m3. The thickness of Puff shall be minimum 40 mm. The sheet panel shall be of indigenous reputed make and be provided with manufactures test certificate. The puff panel shall be fixed to the floor with bottom track of 1.5 mm thick steel U channel section having min size of 50mm X 50mm. The bottom shall be fixed in the floor of the OT with 10mm thicknessand min. 60 mmlong SS fasteners which shall be fully threaded and power drilled The Panels of walls and ceilingshall be tied together by suitable SS coving. The individual wall panels of wall and ceiling shall be tied together by suitable SS coving. The individual wall panels shall be welded together bySS. All joints shall be filled with metal filler and shall be sand casted on site till smooth finish is obtained. Wall & panel joints shall not be visible after the final wall coating is applied. The gap between the masonry wall surfaces and the panel of the theatre shall be sufficient for the flush mounting of equipment’s. This gap shall be provided to accommodate the equipment at a latter date and to enable services, pipes conduits etc, to be run within the gap All wall-mounted equipment shall be flush mounted and sealed in operation theatre. All the sharp edges and corners shall be in radius to avoid bacterialcontamination. The wall panel design shall be such that it enables the installation and supports all equipment’s. Provision of openings required for the installations shall not affect rigidity and strength of the panel. Access boxes shall be fitted to the rear of all wall-mounted equipment to enable maintenance to be carried out from outside the operation theatre. Product should have warranty of at least 10 years. Thework should be executed as per the directions of Engineer–in-Charge.

Supply, installation, testing and commissioning of modular OT ceiling panels with insulated prefabricated puff Panels. The OT ceiling shall be constructed using GI puff panels having 0.8 mm thick GI sheets on both sides. These panels should have been produced in a double band laminator, in which two continuously moving belts carrying 120 GSM galvanized steel sheets of 0.80 mm thickness are firmly bonded together by sprayed -in insulating foam, which hardens during the process. The core consists of rigid polyurethane foam, which has been injected under high pressure, with a minimum density of 40kg/m3. The thickness of Puff shall be minimum 40 mm. The sheet panel shall be ofindigenous reputed make and be provided with manufactures test certificate. The puff panel shall be fixed to the floor with bottom track of 1.5 mm thick steel U channel section having min size of 50mm X 50mm. The bottom shall be fixed in the floor of the OT with 10mm thicknessand min. 60 mm long SS fasteners which shall be fully threaded and power drilled. The Panels of walls and ceiling shall be tied together by suitable SS coving. The individual panels of wall and ceiling shall be tied together by suitable SS coving. The individual wall panels shall be welded together bySS. All joints shall be filled with metal filler and shall be sand casted on site till smooth finish is obtained. Wall & panel joints shall not be visible after the final wall coating is applied. The gap between the masonry wall surfaces and the panel of the theatre shall be sufficient for the flush mounting of equipment’s. This gap shall be provided to accommodate the equipment at a latter date and to enable services, pipes conduits etc, to be run within the gap. All wall-mounted equipment shall be flush mounted and sealed in operation theatre All the sharp edges and corners shall be in radius to avoid bacterial contamination. The wall panel design shall be such that it enables the installation and supports all equipment’s. Provision of openings required for the installations shall not affect rigidity and strength of the panel. Access boxes shall be fitted to the rear of all wall?mounted equipment to enable maintenance to be carried out from outside the operation theatre. Product should have warranty of at least 10 years. The work should be executed as per thedirections of Engineer–in-Charge.

SUPEREQ SYSTEMS (P) LTD RIME Revolving Chair with Knee tilt Synchronic mechanism SUPEREQ SYSTEMS (P) LTD RIME (SP-141) R GEM ID-(5116877-11986239313)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

4 mm thick ACP

Providing Epoxy flooring self leveling type on strong base in desired colour/design as approved by Engineer-in-Charge. Resin for epoxy is to be of floor grade type i/c appropriate hardner and filler material. with 5 year defect liability period

Revolving Chair With Arm Synchronic tilt mechanism (GODREJ INTERIO ACE FULL BACK CHAIR) (Product id: 5116877-70887346890)

BETCO Laboratory Steel Furniture Island bench with table top BETCOR (BETCO-LB-202)

Powder Coated Extruded Aluminium Sections Single Seater Rectangular shape Cluster with Back to Back sitting Modular Work Stations (Product id: 5116877-23085121518)

HEALTHCARE SCIENTIFIC CRCA Sheet With Holes Patient Care Beds HEALTHCARE SCIENTIFICR (HS0101)

Dismantling old plaster and pointing and racking out joints to 15 mm depth disposal of unserviceable material with all leads ……………….. E/I.

Extra for cleaning old surface by scraping the entire old white wash or colour wash including cost of scaffolding do--do-- as per E/I

Taking down Choukhats in doors do ........... do ........... E/I.

Taking down Choukhats in window do .......... do ......... E/I.

Taking down old door and window shutters including stacking serviceable materials within 15M. lead and disposal of unserviceable materials with all leads all complete as per direction of E/l.

Providing 12mm thick cement plaster(1:6) in wall do...do...all comp. Job.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 do...do...E/I.

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows, skylight, fanlights and celestial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l.

S/F/F 200x20x6mm L- type M.S. clamps in Doors properly fishtailed, including making holes and setting the same in 250x125x75mm do...do...E/I.

S/F/F 200x20x6mm L- type M.S.clamps in Doors properly fishtailed, including making holes and setting the same in 250x125x75mm do...do...E/I.

Supplying , fitting and fixing 32 mm thick good quality well dressed and well seasoned sal wood battened shutters, ledged and braced in doors and windows with oxidized iron fittings such as hinges, sliding door, bolts, tower bolts, handles or rings, hooks and eyes, cleats, sand blocks as per schedule taxes and royalty all complete as per building specification and direction of E/l.

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminum fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting & fixing M.S. GRILL made of 20 x 6 mm flat or Square bar as per approved design and drawing properly fabricated with joints continuous fitted, welded and finished smooth, hoisting as per building specification and direction of E/I.

Providing primer one coat red lead paint of approved make over new steel surface including preparing the surface after claaning,removing dust, dirt, scales smokes and grease and cleaning the surfaces thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/l.

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direction of E/l.

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specification and direction of E/l.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over old surface including washing cleaning and preparing the walls scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing P.C.C.(1:2:4) in foundation and plinth do...do... All complete job.

Providing 75B, B/W in C.M.(1:6) in superstructure do...do...E/I.

Removal of old tarfelt and disposal of debris with all leads complete job as per direction of E/I.

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 3 mm thick

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

Supplying, fitting and fixing 20 to 25 micron anodized ammonium 2 tracks with 4 mm float glass Aluminum Windows made from standard extruded section of Hindalco / Jindal of standard sizes :-

CARRIAGE OF MATERIALS Sand Lead -10Km

Stone Chips Lead -8Km

Brick Lead - 8Km

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with piano type switch, phenolic laminated sheet, suitable size PVC/GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. Group C

Group A

Wiring for light/ power plug with 2X4 sq. mm FR PVC insulated copper conductor single core cable in surface/ recessed steel conduit along with 1 No 4 sq. mm PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/submain wiring along with earth wire with the following sizes PVC insulated copper conductor, single core cable in surface/recessed PVC conduit as required. 2 x 4 sqmm + 1 x 4 sqmm earth wire

2 x 2.5 sqmm + 1 x 2.5 sqmm earth wire

2 x 1.5 sqmm + 1 x1.5 sqmm earth wire

Supplying and fixing following way, three pole and neutral, sheet, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator) 4 way (4+12), double door, horizontal type

Supplying and fixing 240 volts, 'C' series, miniature circuit bracker sutable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps, single pole

Supplying and fixing suitable size G.I./PVC box on surface or in recess with phenolic laminated sheet cover in front including providing and fixing 5 pin 5/6 amps socket outlet and 5/6 amps piano type switch, connection, painting etc. as required.

Supplying and fixing suitable size G.I./PVC box on surface or in recess with phenolic laminated sheet cover in front including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps piano type switch, connection, painting etc. as required.

Supplying and fixing batten/angle holder including connection etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required.

Supplying and laying 8 SWG copper wire at 0.50 meter below ground level for conductor earth electrode, including soldering etc. as required

Instalation, testing and commissioning of ceilling fan, including wiring the down rod of standard length (up to 30cm) with 1.5 sq mm FR PVC insulated copper conductor, single core cable etc. As required.

Supplying and fixing 2 pin, 5 amp ceiling rose on the existing junction box/wooden block including connection etc as required.

Providing and fixing following capacity double pole / TP&N sheet metal switch disconnector fuse unit in existing metal board with ISI marked HRC fuses including drilling holes in metal board, making connections, etc. as required. 100Amps, TP&N, HRC

Supplying, fitting, fixing ceiling fan of 1200 mm sweep of any ISI make including carriage to worksite

Supplying, fitting, fixing LED bulb of any ISI make including carriage to worksite

Supplying 4'x20W LED tube light of any ISI make including taxes, carriage to worksite etc. complete job.

S/F/F wash hand basin with C.I / R.S brackets …………………………...…. E/I. (size 550x400mm with single 15mm C.P. Brass pillar cock).

Supplying fitting vitrous white glazed earthen ware I.W.C. of approved make with 100 mm H.C.I. "P" trap 15 liters C.I. Pull and let go flushing cistern of approved make complete with all fiting C.I. Or CC Brackets 32 mm alkathene/PVC telescopic Flush, pipe about 2 M long with one brass coupling and clamps G.I. body brass spindle stopper cock of weight not less than 50 gms, 15 mm PVC connection pipe 450 mm long and the exposed pipe and cistem with who coat of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E.I. with 12.5 ltr. low level PVC cistem.All complete as per building specification and direction of E/I.

Installing of pump set & electrification work supplying and commissioning of 1 HP submersible pump of reputed make ISI marked suitable for 125 x 115 mm dia. tube well and head of 30mtrs. lowering 40mm dia, PVC pipe 50 mtrs. and 2.5 Sq mm finolex coppoer cable with pannelled board, main switch, starter, voltmeter, Ameter, On-off Switch, HRC fuse unit, lighting arrangement all complete job as per specification and direction of E/I

Providing and fixing on wall face unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm dia.

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised Rigid PVC pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door 110x110x110 mm

Bend 110 mm dia

S/F/F of following items Supplying, fitting and fixing the following items with all materials as per specification and direction of E/I. Mirrors of 6 mm thick plate glass bevelled edge mirror including brss revolving fittings 3 mm plywood board and C.P. hinges to fix with mirror (600x450 mm size).

C.P. brass towell rail with bracket container

C.P. brass soap dish container medium quality with screw and hinges etc.

Making holes in walls for laying PVC pipes and restoring the same all cost complete. 250mm dia

Providing and fixing chalorinated polyvinyl chaloride(CPVC) pipes,Having thermal stability for hot and cold water supply including all CPVC plain &brass treaded fittings including fixing the pipes as per E/I. 15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

Supplying and fixing G.I. Fittings of approved make all complete Job as per E/I.Elbow 15 mm dia

20 mm dia

Jam nut 20 mm dia

Plain Socket 15 mm dia

20 mm dia

Tee Plain 15mm dia

20mm dia

Reducing Tee 20 mm dia

Nipple 15mm dia

20mm dia

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : (15 mm nominal bore)

Providing and fixing gun metal ful way valve of approved quality, all complete ……….. E/I. 25 mm dia.

Providing and placing on terrace ( at all floor levels ) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but wi

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:

Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Reinforced cement concrete work in beams, Pracast slab, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.

Supply Installation, testing & commissioning of Air Cooled Ductable Split Units. - Outdoor & Indoor unit shall connected with DX coil, refrigerant piping, firstcharge of refrigerant & oil, HP/LP cutout, thermostatic expansion valve, distributor, starter and other necessary controls to form a factory tested compact unit. The outdoor unit shall have condenser coil, fans with motor & drive, copleand scroll compressors, panel etc. The ductable units should be complete with programable microprocessor panel (BMS Compatible). ( Make: LG / Blue Star / Daikin) 8.5 TR With Scroll Compessor

FFU - 750 CFM with Hepa Filter, 40 MM of WC

FFU - 800 CFM with Hepa Filter, 40 MM of WC

DUCTING, GRILLS,DIFFUSER AND INSULATION Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 0.63 MM (24 gauge) Galvanized Sheet Steel

0.8 MM (22 gauge) Galvanized Sheet Steel

1.0 MM (20 gauge) Galvanized Sheet Steel

Supply,installation and testing of powder coated aluminium extruded grills/diffusers as per specifications given in tender and of following sizes: Single Louvered supply / Return Air registers (Grill)

Supply / return suare ceiling air terminals (diffusers)

Fresh / Exhaust air louvers with bird screen & damper

Flexible connection for AHU/FCU madeup of f/r fabric compelte with flange

Supply,installation and testing of multiblade type GI Duct Damper for duct/collars to be provided with suitable links and quadrants for control of volume of air

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Damper

Actuator

Supply and Application of Acoustic Insulation Inside the Duct with Engineered Nitrile Rubber open cell foam with Density 140 - 180 Kg/m3 passing Class 1 Fire Performance test as per BS 476 Part 7, Air Erosion test for 10,000 fpm air velocity as per ASTM C 1071-05 and with built-in antimicrobial protection. The material should pass Fungi Resistance Test as per DIN EN ISO 846 Method A and Bacterial Resistance Test as per DIN EN ISO 846 Method C; to be applied using manufacturer's recommended Rubber based Adhesive in a blend of solvents.conforming to standard specification. 15 mm thick open cell nitrile rubber.

Supply & Installation of Thermal Insulation on Ducts not exposed to sunlight using Closed Cell Class O Nitrile Rubber Elastomeric Insulation of Density 40 - 60 Kg/m3, Thermal Conductivity of 0.037 W/mk at 20 Celcius Mean Temp. and µ≥7000 (without any additional vapour barrier) and with factory laminated aluminium foil of minimum 60 Microns thickness having weight of 193 gsm as per EN ISO 2286-2, tensile strength shall be 90N/15mm as per EN ISO 527-3 with elongation > 10% as per EN ISO 527-3; to be applied on Ducts using manufacturer's recommended Rubber based Adhesive in a blend of Solvents. 25 mm thick (Class O) Foil for Supply Air Duct

Power Cabling (PVC insulated and PVC sheathed, armoured, Aluminium Conductor of 1.1 KV grade of following sizes. i) For Compressor 3.5C x 16 Sq. mm Aluminium Conductor

ii) For Indoor Unit Blower & Compressor 3C x 4 Sq. mm Aluminium Conductor

iii) For Condenser Fan 2C x 1.5 Sq. mm Copper Conductor

Control Cabling ( PVC insulated & PVC sheathed, armoured, Copper Conductor of 1.1 KV grade of following sizes. 6C x 1.5 Sq. mm Copper Conductor

Supply & laying of 8 SWG GI wire.

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)

B.P.ENTERPRISES

Raja Construction

VERMA ENTERPRISES