SPECIAL REPAIRS TO BLDG No. 3 ABNS LINES AT CDO WING AREA OF HQ JL WING, SPECIAL REPAIRS TO BLDG No. 3A 2 AT 373 I SUP PL ASC AND PROVN OF CERTAIN REVENUE AND MINOR WORKS UNDER GE I BELGAUM

Amount

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thick, below or above GL all as specified and directed.

Demolition of PCC solid block masonry built in cement mortar pillars, etc. in any position below or above ground level all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar or lime cement mortar including all quoins, arches, pillars, etc. but excluding precast concrete articles, in any position below or above ground level all as specified and directed.

Dismantling battens for tiles, etc. of any size spaced exceeding 15 cm including tilting fillets all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Dismantling of asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings including ridges all as specified and directed.

Dismantling of single layer Mangalore pattern or similar tiles in roofing all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing, rubbish off the premises all as specified and directed.

Dismantling of stone slabs and tiles of any description and any thickness in floors laid, bedded and pointed in any mortar all as specified and directed.

Taking down cement plaster on brick or stone wall or ceiling concrete etc. including racking out joints hacking for key scrubbing down with water etc., all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/ dense soil all as specified and as directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in hard/ dense soil all as specified and directed.

Excavation in post holes n.exc 0.5 cum in hard/ dense soil, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25 cm watering and removing surplus soil to a distance n.exc 50 m and making good surface all as specified

Returning filling in with approved excavated soil including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

Removing excavated soil exc 250 m but n.exc 500 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for loose filling with broken bricks of gauge 80 to 150mm in soakage pits, soakage wells, etc. all as directed.

M&L for hard core with broken stone or boulders of gauge n.exc 63mm, deposited, spread ,levelled in layers n.exc 15cm thick, watered and rammed to a true surfaces all as specified and directed.

M&L for plain cement concrete type D2 1:4:8 using 40mm graded stone aggregate as in foundation and mass concrete all as specified and directed.

M&L for plain cement concrete type C2 1:3:6 using 40mm graded stone aggregate as in foundation and mass concrete all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6, type C0, using 12.5 mm graded stone aggregate and setting in CM 1:6 all as specified and directed.

M&L plain cement concrete 1:3:6, type C-1, using 20mm graded stone aggregate as in coping, bed blocks, eves filling between wall and tile/ sheet roofing including necessary form work all as specified and directed

M&L for plain cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in coping, bed blocks including use of necessary form work all as specified and directed

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns etc. all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate in columns, pillars, piers, posts and struts all as specified and directed.

M&L for Reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, and in shelves and the like all as specified and directed.

Supply only approved integral water proofing compound all as specified and as directed.

M&L for honey comb brickwork with sub-class `B’ bricks in one brick thick built in cement mortar 1:4 all as specified and as directed.

Cutting holes in brick walls built in cement mortar for inserting holdfasts, depth of embedded portion measured from the face of the jamb into the wall exc. half brick but not exc. one brick and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required all as directed.

M&L for use of form work to sides of concrete foundations, column footings, plinth beams and similar works for rough finished flat concrete surfaces, vertical or to batter, all as specified and directed

M&L for use of form work to sides of pillars, posts, struts, columns, etc. for fair finished concrete surfaces, square, rectangular or polygonal all as specified and directed.

M&L for use of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc. 200m thick (Horizontal or sloping), flat rough finished surfaces of concrete all as specified and directed.

M&L for use of form work to edges of concrete flats, treads, bands and similar works, for rough finished concrete surfaces, horizontal or sloping, exceeding 5cm but not exceeding 10cm wide all as specified and directed.

M&L for 2nd class hard wood in scantling, clean sawn fixed in unframed work including dismantling of existing unserviceable timber scantling 40 Sq.cm and over in section and in any position in un-framed work and making good disturbed members all as specified and directed.

M&L for 2nd class hard wood chowkhat or frames, plain, solid, wrought, framed and rebated on the solid rounded or chamfered, put together with glue pinned at joints, fixed in position all as specified and directed.

M&L for 35 mm thick second class hard wood, Plain framed, panelled shutter (two panel) with lock rail and panel of 12mm thick plywood BWR 7 ply with commercial veneers on both faces with size of rails and stiles sizes of members of shutters as specified in SSR Part I, Section 8. Clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for 30mm thick 2nd class hard wood glazed/ gauged window/ ventilator shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (b) and fitted to chowkats all as specified and as directed.

M&L for aluminium frame work as in doors, windows, ventilators and partitions using standard aluminium anodised (15 micron) extruded sections including provision of glazing clips, hinges, handles, etc. all as specified and as directed. Notes: (i) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/ fittings. (ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/ supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary rubber gaskets. (iii) Particle board/ glass panels wherever required shall be measured and paid separately.

M&L for 9mm thick veneered decorative plywood, grade 1, with BWR resin, with decorative face veneers on both faces, fixed with screws to timber frame work all as specified and as directed.

M&L for 19mm thick block board, grade 2 quality, interior grade, commercial type as in shutters/ shelves, etc., fixed to timber frame work with screws all as specified and directed

S&F mild steel cupboard knobs, bright finished, 40mm dia, fixed with nut, screw and washer all as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

All as described in item No. 44 but 6mm to 8mm dia

All as described in item No. 44 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

M&L for rolled mild steel Joist, channel, angle, or tee sections, fixed independently without connecting plates, etc. conforming to Fe-290 Grade-E-165 all as specified and as directed.

S&F rolled mild steel angle sections as in purlins, distance pieces, cleats and similar works conforming to Fe-410-W Gde-E-250 quality-A all as specified and as directed.

M&L for mild steel flats as in wind ties for roof including securing bolts and necessary drilling, conforming to Fe-290 Gde E-165 all as specified and as directed.

S&F mild steel framed work such as gates and similar works with ornamental and intricate design, conforming to Fe-290 Gde- E-165, including pintle hinges, stops, hand-made sliding bolts, etc. complete all as specified and as directed.

S&F mild steel works in tubular posts, rafters, purlins, etc. including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 all as specified and as directed.

M&L for pre-painted galvalume coated high tensile corrugated/ trapezoidal profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.45mm thick (TCT), as in roofing/ cladding fixed with self drilling fasteners as per manufacturers instructions of any description and size and making good disturbed roof members all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

M&L for pre-painted galvalume coated high tensile plain profile steel sheets, AZ-70 coating mass, 550 Mpa yield strength, 0.45mm thick (TCT), as in ridges, valleys, hips, claddings, etc. fixed with self drilling fasteners as per manufacturers instructions all as specified and as directed. Note: Measurement shall be taken flat as fixed without any allowance for laps, etc.

S&F corrugated galvanised mild steel sheeting with grade of zinc coating 275, 0.63 mm thick, with two corrugation side laps in roofs, walls, etc. fixed with L-type or J-type or cranked hook bolts including dismantling of existing unserviceable CGI roofing sheets of any description and size and making good disturbed roof members all as specified and as directed.

S&F 4mm thick High Pressure Steam Cured (HPSC) non asbestos fibre cement building board in false ceiling with aluminium anodized snap grids of 60x60cm with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc and applying three coats of white wash on ceiling including dismantling of existing unserviceable false ceiling boards of any description and size alongwith snap grid frame works including making good disturbed wall/ ceiling surfaces all as specified and directed.

M&L for 100mm thick plain cement concrete 1:4:8 type D2 using 40mm graded aggregate as in sub base/ levelling course for flooring all as specified and directed.

M&L for 75mm thick plain cement concrete 1:4:8 type D2 using 40mm graded aggregate as in sub base/ levelling course for flooring all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded aggregate as in sub base for flooring all as specified and directed.

M&L for 40mm thick plain cement concrete 1:2:4 type B1 using 20mm graded aggregate as in flooring including finishing the surface even and fair all as specified and directed.

M&L for 100mm thick plain cement concrete 1:2:4 type B1 using 20mm graded aggregate as in flooring, paving, etc. including finishing the surface even and fair all as specified and directed.

M&L for grinding and polishing the existing old Terrazzo/ Tandoor/ Kota stone flooring/ skirting with necessary white cement, marble powder, etc. complete all as specified and directed.

M&L for coloured glazed ceramic tiles 450mm x 300mm x 7mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in flooring, laid and jointed with neat slurry and pointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 15mm thick screed bed in cement mortar 1:6 all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 10mm thick backing coat in CM 1:4 etc. complete all as specified and directed.

M&L for machine cut granite stone slab, premium quality, any colour, 18 to 19mm thick, set and jointed with neat cement slurry laid over and including 15mm thick screed bed in cement mortar 1:4 and pointed in white cement (1:2) mixed with colouring pigments to match with the shade of slab, as in platforms, steps, cills, etc. including rubbing and polishing complete all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments, set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C1, (using 20 mm graded stone aggregate), 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement including taking down existing cement plaster of any decription, racking out joints, hacking for key, scrubbing down with water, etc. complete all as directed.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 15mm thick in cement mortar 1:4 mixed with water proofing compound on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed. Note: Water proofing compound shall be measured and paid separately.

M&L for rendering 5mm thick in cement mortar 1: 4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as directed. Note: Water proofing compound shall be measured and paid separately.

M&L for 4mm thick sheet glass ordinary quality and glazing with oil putty/ wooden beads in square n. exc. 0.5 sqm in each pane, fixed in repairs, all as specified and directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable), any colour, over a coat of primer over 1mm thick layer of wall care putty on newly plastered walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable), any colour over a coat of primer over 1mm thick layer of wall care putty on walls, pilasters, cornices, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint on old deorated surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on newly plastered surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of weather proof exterior acrylic emulsion paint over a coat of alkali resistant primer on surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of cement based paint, any colour, over a coat of alkali resistant primer on newly plastered surfaces of walls, pilasters, cornices, etc., including necessary preparation of surfaces all as specified and directed.

M&L for preparing surface of wood and wood based materials, new or old of any description and girth, not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L for one coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

S&F15mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F in repairs 15mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F 20mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F 25mm bore galvanized iron tubes, medium grade, with all fittings, fixed complete to walls, ceilings or laid in floors all as specified and directed.

S&F in repairs 15 mm bore Bib tap, long body, brass chromium plated, fancy type with wall flange, with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F 15mm bore stop valves, cast copper alloy, screwed down high pressure, screwed both ends for iron pipe for unions all as specified and as directed.

S&F 15mm bore stop valves, fancy type brass CP, screwed down high pressure, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repairs 15mm bore angle stop valve of brass CP high pressure, screwed for iron pipe and fixed, all as directed.

S&F Vitreous China urinal, bowl type (back or corner wall type), white, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including provision of grating and union for discharge pipe, 15mm bore brass CP urinal spreader, LDPE waste pipe, 5 litres capacity automatic flushing cistern, flush pipe complete all as specified and as directed.

S&F PVC connection 15mm size with PTMT nuts, 450mm long all as specified and directed.

S&F in repairs 32mm size Waste fittings, brass, chromium plated suitable for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

S&F 50mm bore LDPE pipes of pressure rating 6 kg/ Sqcm and fixed complete to walls, ceilings, or in floors all as specified and directed.

S&F 75mm bore UPVC (SWR) pipes single socketed in any length with solvent cement joints laid in floors/ trenches all as specified and directed.

S&F 75mm bore UPVC (SWR) bends any radius with access door all as specified and directed.

S&F UPVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

S&F in repairs 1mm thick Stainless steel Kitchen sink with draining board of overall size not less than 915mmx460mm with bowl size 410mm x 330mm x 160mm with plug, washers waste pipe including bedding in cement mortar, fixing cantilever brackets and connecting union to pipe all as specified and as directed.

Taking down carefully existing point wiring of light/ fan/ bell/ 5 Amps socket/ 15 Amps socket/ 2 way light point, etc. complete of any description including fittings and fixtures such as switches, sockets, call bells, ceiling roses, pendants, holders, regulators, light fittings, etc. and making good the disturbed surfaces of walls, floors, etc. all as specified and directed.

M&L for Point wiring complete with 1.5 Sq mm single core PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded cables drawn through and including ISI marked PVC casing capping of suitable size and all necessary fittings and provision of one run of PVC insulated FRLS unsheathed 1100 volt grade copper conductor multi-stranded single core cable of size 1.5 sqmm and connected to common earth dolly including 2nd class HW board fixed on wall with sunmica top for mounting switches/ sockets etc. for one light point controlled by one switch 1 way complete all as specified and directed.

All as described in item No. 100 but for one ceiling fan/ exhaust fan point controlled by one switch and regulator.

All as described in item No. 100 but for one 05 Amps socket outlet on independent board.

All as described in item No. 100 but for one 05 Amps socket outlet on the same board with other switches.

All as described in item No. 100 but wiring with 2.5 Sqmm single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable and with one run of single core PVC insulated FRLS unsheathed 1100 volt grade multi-stranded copper conductor cable of size 2.5 Sqmm for earth continuity conductor and connecting to common earth dolly, complete for one 15 Amps power socket point on independent board all as specified and directed.

S&F switch, piano type, 5 Amps, flush button, 230 volts, AC, one way all as specified and directed.

S&F switch piano flush type 15 Amps 230 volts all as specified and directed.

S&F socket outlet 5 Amps 3 and 5 pin flush type multipurpose all as specified and directed.

S&F socket outlet 15 Amps 3 and 5 pin 5 and 15 Amps flush type multipurpose all as specified and directed.

S&F PVC ceiling rose 3 terminal suitable for 230 volts AC supply all as specified and directed.

S&F fan regulator electronic step type suitable for 1200/1400 mm sweep ceiling fan all as specified and directed.

S&F in repairs Single pole and neutral enclosure, powder coated, with a two pin earth plug and socket complete, 20 Amps, 240V, including provision of one single pole MCB 20 Amps 'C' curve type all as specified and as directed.

S&F in repairs MCB DB SPN 12 Way with 100 Amps rated bus bars double door type and including provision of 2nd class hard wood board with sunmica top of suitable size fixed to wall and fixing of the MCB DB on board complete all as specified and directed.

S&F RCCB DP 40A 30 mA, 50Hz AC supply all as specified and as directed.

S&F MCB SP 5-32A 10KA 'C' series 50Hz 240 Volts AC supply all as specified and as directed.

S&F in repairs surface mounting LED light fitting, 1x 20W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 20W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F in repairs surface mounting LED light fitting, 1x 10W, 230V, wall/ ceiling mounted type, with extruded aluminium housing and polycarbonate diffuser, 1 No. of 10W LED strip, integrated electronic driver and all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block and provision of 2 Nos. of PVC square blocks all as specified and directed. Make: HAVELLS LUMILINE PLUS or equivalent in CG/ Philips/ Wipro

S&F in repairs energy saving surface mounted, decorative oval bulk head edge-lit LED luminaire comprising of high brightness LED 10 W 6000K with all accessories internally pre wired including suitable size wooden board with sunmica top and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block complete all as specified and directed. Make: Havells ENDURA RUGBY NEO N - IP65 or equivalent in CG/ Philips/ Wipro

S&F in repairs 15 Watts LED security light fitting, with pressure die cast aluminium housing with acrylic diffuser, 15 Watts LEDs, integral electronic driver including all accessories internally pre wired complete and connecting up light fitting with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector block including provision of bracket made out of 40mm bore GI pipe light grade of suitable length and bent to shape fixed to walls/ poles with suitable MS clamps, bolt, nuts etc. complete all as specified and directed. Make: ENDURA CITY LITE PLATINUM model of HAVELLS or equivalent in CG/ Philips/ Wipro

S&F in repairs ceiling fan, 230 volts, single phase, 1200mm sweep, 5 Star rating with all accessories complete all as specified and as directed. Make: HAVELLS Model No. ES-50 5 STAR or equivalent model in makes CG/ ORIENT

S&F exhaust fan, 300mm sweep, 230/240 Volts, 900 RPM, heavy duty, single phase, metallic body with louvres and fixing arrangements with fixing bolts and provision of 3 core flexible copper conductor cable of size 1.5sqmm size from ceiling rose to connector of exhaust fan and testing all as specified as directed. Make: Havells Turbo Force SP model or equivalent model in Almonard/ Crompton Greaves

S&F storage type water heater (Geyser), vertical type, 25 litres capacity, 2000/1500 Watts, 5 Star rating including drilling holes into wall, provision of 4 Nos of suitable size anchor bolts, nuts and washers, connecting up electrical & water supply lines, testing complete all as specified and as directed. Make: MONZA EC model of HAVELLS or equivalent model in RACOLD/ BAJAJ

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick, burried directly in ground vertically (earth pit not less than 2.25 metre deep below normal ground level) with top edge of the earth plate at a depth not less than 1.5m below normal ground level connected to GI wire 4mm dia (upto 7.5m long) by means of GI bolts nuts washers and GI wire protected by 15mm dia light grade GI pipe (upto 7.5m long) and watering arrangements with 20mm dia GI pipe medium grade and GI funnel all as specified and shown in Electrical Plate No 3 of MES Schedule Part I including necessary excavation and earth work in any type of soil, charcoal, dust salt, PCC 1:2:4 type B1 in chamber, 40mm thick RCC 1:2:4 type B1 in cover slab with 8mm dia TMT bars at 100mm C/C both ways and with 8mm dia MS hook complete and testing all as specified and directed.

M/s.Y.N.PATIL

ASHIRWAD ELECTRICALS

RAJENDRA KRISHNA SARAF

M/s. KIRAN M CHOUGULE

M/s. J P CONSTRUCTIONS

SAGAR ENTERPRISES

PRASANNAKUMAR D LATTHE