REPAIR TO JOINERY WORK AND POST CONSTRUCTION ANTI TERMITE TREATMENT TO CERTAIN BUILDING IN TECH AREA AT AFS PATHANKOT

Amount

Taking down steel/wooden/PVC/Aluminium door/windows with chowkat or frames n.exc 1.5 Sqm each. but with shutters (without taking off shutters from the frames) complete all as specified and as directed by Engineer-in-Charge

Taking down steel/wooden/PVC/Aluminium door/windows with chowkat or frames exc 1.5 Sqm but n exc 4 Sqm each. but with shutters (without taking off shutters from the frames) complete all as specified and as directed by Engineer-in-Charge

Taking down and Refixing in same opening shutters of any description exc 1sq.m and n exc 2 sqm each complete all as specified and as directed by Engineer-in-Charge Note : The rate includingudes for taking down, easing and adjusting and also fixing new builders hardwares as required includinguding replacement of unserviceable screws etc.

Taking down and Refixing in same opening shutters of any description exc 2 sqm each complete all as specified and as directed by Engineer-in-Charge Note : The rate includingudes for taking down, easing and adjusting and also fixing new builders hardwares as required includinguding replacement of unserviceable screws etc.

Material & Labour for repair to Aluminium door/windows of any size/any description, includinguding taking down from existing opening and refixing in the same position after tightening, easing the section as required for smooth movement/operation of door/window shutter, includinguding fitting the rubber packing, aluminium snap beading, re-setting floor/hydraulic spring (if required) etc complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top and bottom rails. M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frame at site as per specification and drawing complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing pressed steel frames door 125 x 60 x1.25 mm with one or more rebates includinguding necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate includinguding filling of concrete 1:3:6 type C-1 back of chowkhats, with two coats of synthetic enamel paint over one coat of red oxide primer, includinguding including fixing of holdfast complete all as specified and as directed by Engineer-in-Charge.NOTE:- During Fixing of chowkhat, surface shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and as per site requirement.

Supply & Fixing pressed steel frames door 105 x 60 x1.25 mm with one or more rebates includinguding necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate includinguding filling of concrete 1:3:6 type C-1 back of chowkhats, with two coats of synthetic enamel paint over one coat of red oxide primer, includinguding including fixing of holdfast complete.NOTE:- During Fixing of chowkhat, surface shall be make good in plumb with existing finishes like cement plaster ,similar wall tile,floor tile etc and complete all as specified and as directed by Engineer-in-Charge

Material & Labour PCC type B0, 1:2:4 (12.5 mm graded aggregate) filling in door and frames, any size, single or double rebated, includinguding arrangements complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing Factory made single extruded WPC (Wood PolymerComposite) UV coated solid plain flush door shutter of 32 to 35mm thick size comprising of virgin polymer of K value 58-60.(Suspension Grade), calcium carbonate and naturalfibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screwwithdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm², modulus ofelasticity 850 N/mm² and resistance to spread of flameof Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunkS.S screws, in kitchen cupboards and room wardrobes shutter complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing for 30mm flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides particle board core complete all as specified and as directed by Engineer-in-Charge. NOTE :- All screws shall be self tapping chrome plated

Supply & Fixing Factory made fully wire gauged (single piece both sides) PVC prelam door shutter 33-35mm thick style consisting of frame made of MS tubes 19x19mm top and 19mm in styles. Single piece plainbottom rails and 19mm coloured PVC sheets 5mm thick to be used to cover styles and rails. PVC sheet strip of 20mm width stuck inside on either side as gap insert for top rail and bottom rail. Panel will be wire guaged tightly and firmly as per mfr instructions complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing Galvanised stainless steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing anodised aluminium frame for doors,windows,ventilators and partition etc with one or more rebates includinguding joining cleats for fixing etc complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing anodised aluminium door shutters aluminium section weighing 0.55 kg/m includinguding necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as hinges type B-21 100mm long (03 Nos) suitable handle (02 Nos) tower bolt 150mm long (02 Nos),door stopper 01 nos complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing anodised aluminium Window and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 kg/m includinguding necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (01 No), hinges type B-21 100mm long (02 Nos) suitable handle (01 No) complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing 5.5mm thick tinted glass for aluminium doorss and glazing with clips complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing 12mm thick particle board pre-laminated both sides with decorative choice laminations, interior grade, fixed in aluminium doors complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing 4 levers mild steel mortice lock, vertical type, size 100mm complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing Door closer of aluminium (extruded section) hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, includinguding cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete all as specified and as directed by Engineer-in-Charge

Supply and fixing in repair for factory made Steel window/ Ventilator 1.25mm thick box type (primer coated) ERW hollow P section of size 60mmx25mm includinguding grill using 10 sqmm bar double rebated both gauge and glass shutter comprised gauged glazed Skelton shutter ERW sec 50mmx20mm and 1mm thick with two open able leaf consisting two Nos sash bar of T Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T Section of size 60mmx25mm and 1.25mm thick refer TD Drawing No CEAF/AR-480/2015 Sheet No 2(A)/4 dated 30.12.2015 includinguding following fitting welded to frame shutter : (a) Hold fast,150mm long of 12mmx3mm made to shape O4 Nos per window (b) handle of Z Sec20mmx25mm, 100mm long-per No leaf (c) MS Tower bolt 150mm long-02No per leaf . (d) Z section 20mmx25mm, 100mm long stopper 1 No per leaf. (e) cleat 55mm long of hollow square 15mmx20mmx63mm welded to hinge. 1 No per leaf (f) MS Pintal hinges of size 75mmx12mm. 2 Nos per leaf, (g) includinguding two coats of synthetic enamel paint complete. (h) Stainless steel wire cloth, 0.25mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to 2mm &fixed with aluminium wire staples. (j) Glass pane 5 mm thick fixed with MS pin and oil putty complete all as specified and as directed by Engineer-in-Charge. NOTE: During Fixing of window, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.cutting holes and good dismantled portion in PCC(1:2:4) type B1.

Supply & Fixing Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, includinguding drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. and of approved quality with 6 mm thick figured glass and ss wire mesh of 0.36 mm nominal dia and average width of aperture 1.40 mm, complete all as specified and directed by Engineer-in-Charge. Note:- The rate shall also includingude making all damages/plastering repair, leveling and making good in plumb all the cills and jambs of opening before fixing windows and , shall deemed to have been includinguded in the quoted rate and no extra shall be admitted at a laterdate in this respect.

Supply & Fixing for MS Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing factory made uPVC white colour Casement dooor with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 + 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 + 0.2mm thick galvanised mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimensions, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100x8mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded includinguding drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and as directed by Engineer-in-Charge. (Glass & uPVC Panel shall be paid seperately) Note : For uPVC frame, sash and mullion extruded profiles minus 5% tolerence in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fix Aluminum composite pannel 4 mm thick as in sash of the bottom portion of UPVC doors complete all as specified and directed by Engr In Charge.

Supply & Fixing 100 mm butt hinges, medium weight, mild steel fixed in MS frame or welded with MS angle frame complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing Aluminium, anodised, barrel tower bolts of extruded section and fixed 150 mm long complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing Aluminium, anodised, barrel tower bolts of extruded section and fixed 200 mm long complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed 250 mm long complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing in Aluminium handles, cast type, anodised 150mm long in complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing Floor door stopper of aluminium alloy body and tongue, anodised, 140 mm with hard drawn steel spring, fixed in floor complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing in repair door closer Aluminum (Extruded section ) Body hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing in repair 100 mm butt hinges, medium weight, mild steel fixed in MS frame or welded with MS angle frame complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing in repair Aluminium, anodised, barrel tower bolts of extruded section and fixed 150 mm long ccomplete all as specified and as directed by Engineer-in-Charge

Supply & Fixing in repair Aluminium, anodised, barrel tower bolts of extruded section and fixed 200 mm longcomplete all as specified and as directed by Engineer-in-Charge

Supply & Fixing in repair Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed 250 mm long complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing in repair in Aluminium handles, cast type, anodised 150mm long in complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing in repair Floor door stopper of aluminium alloy body and tongue, anodised, 140 mm with hard drawn steel spring, fixed in floor complete all as specified and as directed by Engineer-in-Charge

Material & Labour preparation of old painted wooden surfaces of any description not otherwise described over 10 cement mortar width or girth and applying one coats of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge

Dismantling false ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs any thickness complete all as specified and complete all as specified and as directed by Engineer-in-Charge

Supply and fixing position suspended false ceiling system using T-grid suspended ceiling grid system . The size of grid shall be 600x600mm with GI frame work main runner 38x24mm, cross tee 25x24mm/25x24mm and wall angle 24x24mm( thickness of the materail of 0.30mm). using 9mm thick ceiling panel laminated with PVC film on front face and foil back available in the drop texture as per IS-2095, part-I 1996, fixed in the grid of T-grid suspended ceiling grid system duly susupended by 4mm dia GI bar hanged from the purlins of the roof with butter fly clips complete all as specified and directed by Engr-in-Charge.

Supply & Fixing Sheet glass 3mm thick ordinary quality and glazing with oil putty includinguding Hacking out old glasses from steel window / ventilator in any position and any description includinguding punching or drilling out old glazing pins / springs clips and providing and fixing new one complete all as specified and as directed by Engineer-in-Charge

Supply & Fixing Figured glass, Pin head type 3mm thick and glazing with oil putty includinguding Hacking out old glasses from steel window / ventilator in any position and any description includinguding punching or drilling out old glazing pins / springs clips and providing and fixing new one complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm as in doors and windows with necessary nuts and bolts/ fillets complete all as specified and as directed by Engineer-in-Charge

Taking down carefully (copper/aluminium) point wiring for ceiling fan/light fitting in ceiling/wall and refixing the same in any position includinguding replacing damaged material and lowering/rising the rod of ceiling fan if required complete and all as specified and directed by Engineer-in-Charge.

Taking down carefully switch boards of any size and any description and boxes of such types on wall and refixing at same place duly modification over PVC panelling includinguding necessary screws, washers, replacement of damage switches etc. complete all as specified and directed by Engineer-in-Charge.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing 5mm thick PVC sheet fillet of width 35mm for wall paneling includingusive of fixing on to wall to make PVC Frame as per specification and directed by engineer in charge.

Supply & Fixing 5mm thick Prelam PVC sheet (Coloured & decorative) in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions includingusive of Solvent Cement and fixing at site complete all as specified and as directed by Engineer-in-Charge

Taking down cement plaster of any description any layer and thickness on brick or stone walls and ceiling includinguding raking out joints, hacking for keys, scubbing down with water etc and complete all as specified and as directed by Engineer-in-Charge

Material & Labour for 10 mm thick rendering in cement mortar 1:6 on fair faces of brick surfaces complete all as specified and as directed by Engineer-in-Charge

Material & Labour for applying 3mm thick in two coats wall care putty on Internal wall complete all as specified and as directed by Engineer-in-Charge

Material & Labour for preparation of New plastered surfaces by washing, rubbing down and stopping of distempered surfaces and applying two coat of oil emulation distemper on wall over a coat of primeretc complete all as specified and as directed by Engineer-in-Charge

Material & Labour for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick surfaces finished even and smooth (without using ) extra cement complete all as specified and as directed by Engineer-in-Charge

Material & Labour for preparation of surface and applying two coats of exterior emulsion paint (weather coat) in camouflage pattern , any shade or colour as approved over a coat of primercomplete all as specified and as directed by Engineer-in-Charge

Material & Labour preparation of new untreated wooden surfaces of any description not otherwise described over 10 cement mortar width or girth and applying two coats of synthetic enamel paint over a coat of pink primercomplete all as specified and as directed by Engineer-in-Charge

Material & Labour preparation of new untreated Steel surfaces of any description not otherwise described over 10 cement mortar width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome complete all as specified and as directed by Engineer-in-Charge

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any motar complete all as specified and as directed by Engineer-in-Charge.

Material & Labour 15-20mm thick Granite(of any type) work (table rubbed and polished) in window cills / counter for WHB or steel sink after cutting as required size for WHB & Sink set in cement mortar (1:4) includinguding pointing using marble dust with admixture of pigment to match with shade of granite includinguding 20 mm thick screed bed in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge

Material & Labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm includinguding excavating channel along the wall and rodding etc. complete, complete all as specified & directed. by engr in charge

Material & Labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre includinguding drilling and plugging holes etc. in apron, complete all as specified & directed by engr in charge.

Material & Labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart includinguding drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as per manufacturers specifications & directed. by engr in charge.

Material & Labour Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same.complete all as specified and directed by engr in charge

Dismantling floor, hearth or wall tiling includinguding cement mortar bedding (but not backing), removing rubish of the premises complete complete all as specified and as directed by Engineer-in-Charge

Material & labour for Non skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match laid over screed bed or bedding layer 15 mm thick in cement mortar 1:6 includinguding complete all as specified and as directed by Engineer-in-Charge

Material & Labour 18 to 20 mm thick machine cut Kota stone slab flooring, landing,steps over and includinguding 20mm thick screed bed in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab includinguding rubbing and granite polishing complete all as specified and as directed by Engineer-in-Charge

Material & labour for coloured glazed ceramic tiles in vertical surface 450 x 300 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the shade of tiles includinguding 10 mm thick screed bed or bedding layers in cement mortar 1:3 for laying tiles on vertical surfaces, complete all as specified and as directed by Engineer-in-Charge

Removing the plant/growth of any description size, any location of external surfaces of walls shafts by cutting/burning with blown lamp of any other means & remvoing the roots completely spraying the suitable chemical in the removed portion to avoid re-growth & making good damaged portion to match the existing surfaces by PCC type B0(1:2:4) 12.5 mm graded aggregate/cement mortar 1:3 upto the height of 20 Mtr includinguding all necessary safety precaution complete all as specified and as directed by Engineer-in-Charge

Demolition of cement (un-reinforced) in any position not otherwise specifically provided complete all as specified and as directed Engineer-in-Charge

Material & Labour 75 mm thick Cement concrete type C-2, 1:3:6 (40 mm graded aggregate) as in plinth protection complete all as specified and as directed by Engineer-in-Charge

M/S G P MARWAHA (BID ID -3333876)

dadwal engineers (BID ID -3325370)

LAKSHMI BUILDING INOVATORS (BID ID -3334209)

Vijay Kumar Contractor and Engineers (BID ID -3324003)