SPL REPAIR TO BLDG NO T -460 AND T- 461 AND OR LIVING AND COOK HOUSE AT BLDG. NO P-798 UNDER AGE B/R- V AND AGE E/M -V OF GE (N) BATHINDA AT BATHINDA MIL STN

Amount

B/R Works

Dismantling brick/PCC terracing tiles single layer in roof laid and pointed in cement mortar and removing/ disposal off from the site complete all as specified and as directed by Engineer-in-charge.

Demolition of mud in roofs, any thickness, including plastering and leaping (whether full thickness removed or only a part there of) including removing/cutting uprooting grass, vegetations and roots of small plants etc on roof floor and surrounding/parapit wall etc, including removing rubbish material from building and thrown in low lying empty area (as per direction of AGE/JE) at a distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge.

Material and labour for cement concrete (1:2:4) type B-0, (using 12.5 mm graded stone aggregates) as in roof padding, bands, bedding, benching of manholes, coping, surface channel, roof kerbs or mud stops, rounded or chamfered on edges etc including use & waste of necessary form work complete all as specified and as directed by Engineer-in-charge.

Material and labour for rendering 10mm thick screed bed in cement mortar 1:3 with WPC as per manufacturer's instructions on roof for roof treatment complete all as specified Note : WPC will be measured and paid separately as supply only)

Supply only Integral waterproofing compound

Material and labour for cleaning top surface of concrete roof slab, lime terracing, or surface of tiles, with wire brush including flashing and junction of parapets etc. and surface painting with layer of blown grade bitumen of any penetration applied hot @ 1.70 Kg per Sqm and 15mm thick screed /rendering in cement mortar (1:6), priming the surface @ 0.30 Kg per Sqm and laying 3mm thick APP based polymer membrane of weighing not less than 3.5 Kg per Sqm reinforced with polyster non woven fabric (weight not less than 150 Gm per Sqm) laid on primed surface at by torch application with side overlap 75mm and end overlap 100mm and tucked into the chases as a treatment for moderate condition complete all as specified and as directed by the Engineer-in-Charge.

Demolition of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, in any description including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by Engineer-in-charge.

M&L for brick work with subclass ‘B’ bricks,(old size bricks) straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Taking down cement or cement lime plaster from brick wall etc including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for rendering/plastering appx 10mm thick (matching with existing plaster thickness) in cement mortar (1:3) on any face of ceiling in patches matching with existing, finished even and smooth without using extra cement, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering/plastering appx 15mm thick (matching with existing plaster thickness) in cement mortar (1:6) on old brick or concrete surfaces of walls/pillars /cornices in patches matching with existing, finished even and smooth without using extra cement, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering/plastering 15mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces (external surface), finished even and smooth without using extra cement, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparing newly plastered or concrete surface of ceiling by sand papering or by other means and applying two coats of white wash with (paint brush /with roller ) complete all as specified & directed by Engineer-in- charge

Material and labour for preparation of old decorated surfaces (plastered/unplastered) of ceiling by remove / scraping down all loose particle, smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean including applying 2mm thick wall care putty to make the surface smooth and glossy upto the entire satisfaction of Engineer -in-Charge and applying two coats of white wash with roller only complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new plastered/ concrete surface of wall/ pillars/ cornices by brooming down with using broom/sand papering or by other means, and preparing the surfaces smooth by applying 2mm thick wall care putty, to make the surface smooth by using sander machine (with provision of dust sucking) upto entire satisfaction of Engr-in-Charge and applying two coats of plastic emulsion paint (with roller brush ) complete all as specified and as directed by Engineer-in-Charge.

Matterial and labour for complete removal of existing treatment (any layers of existing treatment) and efflorescence from old decorated surface of wall/pillars/cornices by scraping down with using Mechanical sander machine (including provision of dust sucking) upto entire satisfaction of Engineer-in-Charge brooming down and preparing the surfaces smooth and making good by applying 2mm thick wall care puty with white cement based and sanding the surface by Mechanical sander machine to make the surface even and smooth upto entire satisfaction of Engineer -in-Charge and appplying two coats of plastic emulsion paint (with roller brush only) complete all as specified and directed by Engineer-in-Charge

Material and labour for preparation of newly plastered/ concrete surface of wall/Pillars/cornices by brooming down with using broom/sand preparing or by tany other means, and preparing the surfaces smooth by appling one coat of primer and applying one coat of 2mm thick wall care putty to make the surface even and smooth by using sander Machine (With provision of dust sucking) upto entire satisfaction of Engineer-in-Charge and after preparing the surface applying three coats of acrylic smooth exterior emulsion paint, as approved tint/colour by using paint roller brush complete all as specified and directed by Engr-in-Charge

Material and labour for complete removal of existing treatment (any layers of existing treatment ) effloresence from old decorated surface of wall/pillars/cormices by scraping down with using Mechanical sander machine( including provision of dust sucking) upto entire satisfaction of Engineer-in-Charge brooming down and preparing the surfaces and applying two coats of acrylic smooth exterior emulsion paint of approved tint/colour by using paint roller brush only complete all as specified and directed by Engr-in-Charge

Material and labour for rough cast plastering including 15 mm thick rendering in cement plaster 1 :4 complete as specified in SSR Part-I clause 14.22 as given in Note : Rough cast finish. After applying under coat of cement mortar 1:3 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel agg. which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1 shall be applied complete including taking down existing cment or cement lime plaster and applying two coats of cement based paint over a coat of primer all as specified and as directed by the Engineer-in-Charge.

Dismantling of floor, hearth or wall tiling including cement mortar bedding but not backing including removing rubbish material from building and thrown in low lying empty area (as per direction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge

Material and labour for vitrified ceramic coloured tiles (light shade) 10 mm thick square or rectangular, area of each tile not exceeding 0.36 sqm, as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for vitrified ceramic coloured tiles (light shade) 10mm thick square or rectangular (same as floor tile, as per above item ), as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick bedding layer (rendering) in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge.

Material and labour for Non Skid ceramic coloured tiles 7 to 8 mm thick, square or rectangular, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for Glazed ceramic coloured tiles of size 350mmx 250mm / 450mmX 350mm/ 450mmX 300mm, 7mm to 8mm thick, as in vertical surface, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick (Av thickness) bedding layer (rendering) in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge.

Demolition of stone/marble slabs of any description or thickness as in floors/ cooking platform/steps etc. laid, bedded and pointed in any mortar including removing rubbish material from the site complete all as specified and as directed by Engineer-in-charge

Material and labour 18-20mm thick machine cut, granite duly factory grinding and polished (table rubbed and polished) of approved colour for counter sunk wash basin, plateform/cooking plateform or as directed, over and including screed bed 15mm thick in cement mortar (1:4) with grey cement slurry including pointing in white cement (1:2) using marble dust with admiture of pigment to match with shade of granite stone slab including cutting as required including cleaning and extra polishing if required complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 18-20mm thick any of black/mahroon colour of marble work other than (table rubbed and polished) as in counter sunk wash basin, steps, jambs, pillars, window cills, cooking platforms and like, set and including screed bed 15mm thick in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admiture of pigment to match with shade of marble slab, including machine cutting to make it square or rectangular or as per site requirement including cleaning and extra polishing if required, complete all as specified and as directed by Engineer-in-Charge.

Material and labour for machine cut kota stone slab as in flooring, 20-25mm thick over and including 20 mm thick cement screed base in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engineer-in-Charge.

All as per item No 29 above but in dado/skirting /vertical surface including 15 mm thick (Av thickness) bedding layer (rendering) in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness (below or above ground level) including removing rubbish material from building and thrown in low lying empty area (as per direction of AGE/JE) at a distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge.

M&L 100mm thick Cement concrete 1:4:8 type D 2, (40mm graded stone aggregate) as in sub base complete all as specified and directed by Engr-in-Charge

Material and labour for machine pressed precast interlocking paver block 60 mm thick with grey cement and no pigment, factory made, any shape and size (as approved by GE), conforming to IS 15658-2006, made of M-35 grade concrete, laid over and including 25 mm thick layer of sand cushioning complete all as specified and as directed by Engineer-in- charge. Note: The rate of 25mm thick layer of sand cushioning is included in this item and nothing shall be paid extra on this account.

Material and labour for 75mm thick PCC (1:3:6) type C-1 (using 20mm graded stone aggregate) as in flooring, hard standing, plinth protection/path etc. finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing anodised aluminium snap grid frame work of size of grid 605 x605mm for false ceiling including necessary notching and preparing holes, the snap grid shall consist of anodised aluminium main tee of size 36.5mm x 25mm x 1.4mm weighing 0.24 Kg/RM, cross and intermediate tee of size 23.5mm x 26.4mm x 1.4mm weighing 0.191 Kg/RM. The main and cross tee shall be jointed at junction with steel screws or MS bolts, nuts and washers, the snap grid (main / cross tee sections) shall be supported at ends all along the wall with anodised aluminium angle of size 35mm x25mmx 2mm weighing 0.36 Kg/RM fixed to wall with suitable arrangement and duly suspended with 4mm GI wire hangers (upto 1200 mm length) adjusting level fixed to roof slab by means of ceiling cleats made of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including providing 12mm thick gypsum board in grid fixed in false ceiling grid made of aluminium as per above including dismantling of exisitng false ceiling specifications complete all as specified and as directed by Engineer-in-charge.

Material and labour for solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification, including 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing for mild steel cupboard shutter two leaves with frame of 20 gauges MS sheet (all around) and leaves of 21 gauge MS Sheet ( all as per Godrej Pattern) with three way locking arrangement with brass lock with CP handle with duplicate key including two coats of spray painting over a coat or red oxide primer complete fixed in existing cupboard, fixed with necessary nuts, bolts including embedding in PCC 1:2:4 (Area's opening shall be measured) complete all as specified.

Material and labour for 18 mm thick prelaminated MDF board , exterier grade (grade-1) confirming IS 14587, fixed with screws for kitchen cupboard and cabinet shelf for cupboard including cut edges of prelaminated board to be sealed with 6mm teak wood lipping and all necessary fittings including dismantling of board of any description and type complete all as specified and directed.

Material and labour for 12 mm thick prelaminated partical board interior grade prelaminated both side with decorative choice lamination fixed with screw to timber frame work/aluminium frame work including dismantling of board of any size and type complete all as specified and directed.

Supply and fixing 30mm wide continuous (piano) hinges, mild steel, bright finish or electrogalvanised fixing to wooden frame complete all as specified

Supply and fixing 100mm long fancy type stainless steel handles, cast type, polished bright complete all as specified and directed

Supply and fixing magnet catcher fixed in cabinet shutter (one portion) and wooden frame (other portion) with screw complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutters from the frames, wooden/PVC doors/steel ventilator) area not exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4 Sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge.

Supply and fixing factory made 105 x 60mm pressed steel frames, thickness of sheet 1.25mm for doors with one or more rebates including supply and fixing necessary lugs and lock strike plate, etc. complete all as specified and as directed by Engineer-in- charge. Note : - (i) Butt hinges shall be measured and paid separately under appropriate item of BOQ.

M&L for PCC (1:3:6) type C-0 (using 12.5mm graded stone aggregate) as in back filling of chowkats and for hold fast complete all as specified and directed by Engr-in-Charge

Supply & fixing factory made plain framed panelled shutters (two panels as approved), 35mm thick of 2nd class hard wood with lock rail and panel inserts of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I), kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401, including 2nd class soft wood kail beading 20mm wide tapering from 10mm to 5mm on one side and also fitted to chowkhat complete all as specified and as directed by Engineer-in- charge. Note : - (i) The sutters shall be brought at site without primer and same shall be applied at site as per direction of Engineer-in-charge. Primer shall be measured paid separately under appropriate item (painting) of BOQ.

Supply & fixing factory made glazed and skeleton shutter, 35mm thick of 2nd class hard wood open rebated (two panels as approved) and prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc. Sizes of members as specified in SSR Part-I, Section 8 and fitted to chowkhats, menbers shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and as directed by Engineer-in- charge. Note : - (i) The shutters shall be brought at site without primer and same shall be applied at site as per direction of Engineer-in-charge. Primer shall be measured paid separately under appropriate item of BOQ.

Supply and fixing for steel window box type double shutter (glazed with wire gauge) with side hung shutters including hinges with steel handle and steel peg stay complete with glazing bar dovetailed or welded and including window guard bar, tower bolt, flat iron for fixing wire netting including one shop coat of zink chromate primer paint and making good to distrubed portion match with existing surfaces including taking out of existing steel window complete all as specified.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, fixing in opening as per specification complete all as specified and as directed by Engineer-in-Charge

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 100mm long powder coated mild steel butt hinges medium weight cold rolled complete all as specified & directed by Engineer-in-charge.

Supply and fixing anodised aluminium handle cast type 125mm long complete all as specified & directed by Engineer-in-charge.

Supply and fixing anodised aluminium handle cast type 150mm long complete all as specified & directed by Engineer-in-charge.

Supply and fixing aluminium anodised barrel tower bolt of extruded section, 200mm long complete all as specified & directed by Engineer-in-charge.

Supply and fixing aluminium anodised barrel tower bolt of extruded section, 150mm long complete all as specified & directed by Engineer-in-charge.

Supply & fixing aluminium anodised sliding door bolts 250mm long, with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed by Engineer-in- charge.

Supply and fixing mild steel 300mm long rat tail rod pattern spring including roller and roller plate and fixing to wooden frame with screw complete all as specified and directed by Engr-in-Charge

Supply and fixing in repair Floor door stoper (150mm) of aluminium alloy body and tongue, anodised , with hard drawn steel spring fixed in floor complete all as specified and directed

Supply & fixing powder coated aluminium anodised frame (partition, door, ventilator, window) made out of aluminium section / aluminium chanel, powder coated (minimum thickness of powder coating not less than 50 micron), for doors, windows, ventilators, partition) with one or more rebate including jointing cleat for fixing etc. including taking down old unserviceable frame complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing in repair anodised powder coated aluminium shutter for door made out of aluminium section weighing 0.55 Kg/mtr, powder coated (minimum thickness of powder coating not less than 50 micron) including aluminium hardware i.e. necessary joining cleats, glazing clips, rubber neoprene packing, suitable size of aluminium handles 2 Nos and aluminium hinges 04 Nos in each leaf (size of handle and hinge as directed), anodised aluminium snap beading, screws etc including fixing of glass, complete all as specified and directed by Engineer-in-Charge. Note :- (i) Aluminium chowkhat frame shall be measured and paid separately under appropriate item of BOQ as supply and fixing. (ii) Glass and other filling material in panels shall be measured and paid separately under appropriate item of BOQ.

Supply and fixing in repair powder coated anodised aluminium with minimum thickness of powder coating 50 micorn window and ventilator shutter, glazed side/top hung type without sash bars, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, luminum snap beading screws, screws, anodised aluminium fittings such as peg stay 150mm long (1 No), hinges type B-21 100mm long ( 2 Nos), suitable size handle ( 1No) drawing and size as approved by GE complete all as specified and directed by Engineer-in-charge . Note :- (i) Aluminium chowkhat frame shall be measured and paid separately under appropriate item of BOQ as supply and fixing. (ii) Glass and other filling material in panels shall be measured and paid separately under appropriate item of BOQ.

Supply & fixing 5.5mm thick tinted sheet glass ordinary quality/figured glass pin head in squares not exceeding 0.5sqm in each pane and fixed with oil putty etc. as required or as directed complete all as specified & directed by Engineer-in- charge.

Supply & fixing aluminium (extruded section) body door closer hydraulically regulated, designation No 3, universal type suitable for door shutter of 851 to 1000mm in width and weight between 61 to 80 Kg, ISI marked complete all as specified & directed by Engineer-in-charge.

Material and labour for mild steel work conforming to Fe-290 (Gde E-165) as in grills, gratings etc. with ends of bars shouldered and/ or rivetted or forged into spikes; framed guard bars, walkways, railing, framed work of water tanks and similar works complete all as specified and as directed by Engineer-in- charge.

Supply & fixing galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tack or galvanised wire staples complete all as specified & directed by Engineer-in- charge.

Material and labour for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed by Engineer-in- charge.

Material and labour for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossing finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed by Engineer-in- charge.

Material and labour for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth by cleaning the dust and removing all loose particle with using sanded paper, clean cloths and dry paint brush & applying one coat of synthetic enamel paint (1st quality) of approved tint/colour to achieve glossy finish with using paint brush complete as specified and as directed by Engineer-in-Charge.

Material and labour for reinforced cement concrete M-25 (Design mix) as in Beams, cantilevers, bressummers, chajjas, Plinth beam, lintels, chajas etc over 1.5m span complete all as specified and directed.

Material and labour for reinforced cement concrete M-25 (Design mix) as in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings,girders , bressummers, lintels, chajjas, cantilevers, shelves including supports,overhangs,etc. also splays between floors and beams, etc.complete all as specified and directed.

Use and waste of form work to fair finished soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Material and labour mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No-75 above , but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed .

Dismantling wrought iron or mild steel work of any description not otherwise provided for truss, purlin rafter etc complete all as specified and directed by Engr-in-charge

Dismantling of framed trusses size n exc 10 mtr of any thickness complete all as specified and directed by Engr-in-harge

Material and labour for mild steel work tubular poles/post including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to latest relevant IS grade St-240 complete all as specified & directed by Engineer-in- charge.

Material and labour for mild steel framed work/Framed brackets in repair using MS angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, rails, braces, riveting, nut bolts etc., complete conforming to Fe 410-0 or 310-0 (Gde-E- 250) quality-A i complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of Plain or corrugated steel sheeting, any gauge, thickness, as in roof coverings of complete all as specified and as directed by Engineer-in-charge.

Supply and fixing pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick, any colour having tensile strength of 550 Mpa as in ridge (including cutting and bent to shape), roof covering, fixed with self tapping screws complete all as specified and as directed by Engineer-in-charge.

Material and labour for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete including fabrication as directed, including hold fast, locking arrangement, sliding door bolt, stopper etc conforming to Fe-410-W (Gde E-250) quality A complete all as specified and as directed by Engineer-in- charge

Taking up or down existing galvanised steel water tubing (GI pipe) 15mm bore including fitting/connection from wall/ceiling/floor/concealed etc. including removing from site/keeping aside for reuse (serviceable as good condition as directed) complete all as specified and as directed by Engineer-in-charge.

Taking up or down existing galvanised steel water tubing (GI pipe) 20mm bore including fitting/connection from wall/ceiling/floor/concealed etc. including removing from site/keeping aside for reuse (serviceable as good condition as directed) complete all as specified and as directed by Engineer-in-charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 15mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor or concealed in walls including cutting chases in wall (as required) and making good disturbed surfaces of walls including cutting and threading of existing pipe any dia for insertaion of tee branch including hole in wall to pass the pipe out side for connection as per site requirment complete all as specified and as directed by Engineer-in- charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 20mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor or concealed in walls including cutting chases in wall (as required) and making good disturbed surfaces of walls including cutting and threading of existing pipe any dia for insertaion of tee branch including hole in wall to pass the pipe out side for connection as per site requirment complete all as specified and as directed by Engineer-in- charge.

Supply & fixing vitreous china wash hand basin oval type under counter, white colour, of size 410mm x 310mm x 220mm excluding pillar taps, but including fancy type 32mm waste coupling and waste pipe, fixing/counter sunked in granite slab, complete all as specified and as directed by Engineer-in-Charge. Note :- Granite slab shall be measured and paid separately under appropriate item of BOQ.

Supply & fixing in repair vitreous China squatting pan 'Orissa' pattern white of size 580mmx440mm with integral foot rests (excluding flushing cistern, flush pipe above floor and trap), including demolition of tile, PCC, taking out old WC, taking out lime concrete filling and after fixing new WC re filling lime concrete (1 lime, 2 sand or surkhi and 5 aggretate), min. 150mm thick all round and finished just below level of rim of pan to receive the floor finishing, including fixing PVC flush pipe upto finished floor level, joints of flush pipe and trap make leakproof and testing before filling concrete and including all other connected work as required upto entire satisfaction of Engineer-in-charge complete all as specified and as directed by Engineer-in- charge.

Supply and fixing in replacement one piece (single unit EWC with flush tank) white colour with all fittings including seat cover, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement 10 litres capacity PVC valveless syphonic action type low level flushing cistern white with inlet, ball valve, float, handle including brackets and 32mm dia PVC flush pipe complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement stainless steel sink made out of 1.00mm thick sheet, overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm, kitchen or laboratory with plugs, washers, waste pipe including bedding in cement mortar, fixing in existing space or fixing with cast iron cantilever brackets and connecting union to waste pipe, including taking down old unserviceable sink including fixing to granite/marble stone complete all as specified and directed by Engineer-in-Charge.

Supply & fixing Glass sheet assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-charge.

Supply and fixing in replacement stainless steel pipe 25mm dia, wall thickness of pipe not less than 20 guage, as curtain rod fixing with and including fancy type brackets and decorated end knobs (finials), stop roller etc, fixed on wall for doors and windows curtains, cuttings as required length and fixing at site including fixing arrangements, rawl plug, screws etc. including taking out old any type rod or pelmet boxes with curtain rod complete all as specified & directed by Engineer-in- charge.

Supply and fixing stainless steel plate rack standred of min size 750mm x900mm fixing with steel screw and all necessary items complete all specified & directed by Engineer-in- charge.

Supply & fixing in replacement Bib taps, cast copper alloy fancy type, chromium plated, with long shank long body, with crutch or butterfly handle, screwed down, screwed for iron pipe of size 15mm bore complete all as specified.

Supply & fixing rotational moulded polyethylene water storage tank white colour, of capacity 1000 litres (cylindrical vertical, triple layered with closed top), hoisted and fixed in position including making inlet and out let connection and including 20mm ball valve and including dismantling of old water tank complete all as specified and as directed by Engineer-in-charge.

Supply & fixing 15 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply & fixing 20 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Supply & fixing Soap dish, vitreous China white/stainless steel, approximate size 160x160x90mm complete all as specified and directed.

Supply & fixing brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

Supply & fixing PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified & directed.

Supply & fixing 15 mm pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

Supply & fixing in replacement 15mm bore/ dia chromium plated stop valve/angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed complete all as specified and directed.

Supply & fixing 15mm bore/ dia stop valves cast copper alloy, chromium plated, fancy type, with long shank & cup (concealed type) complete all as specified and as directed.

Supply & fixing chromium plated shower rose 125mm size with or without swivel joint including fixing to steel pipe or union complete all as specified and directed.

Supply & fixing 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, for drain or rain water, fixed along walls with stack clamps made out of FI 50x5 mm and 16 mm dia round iron stay (at 1 m interval) including nuts, bolts & PCC work including taking down old pipe with fittings complete all as specified and directed.

Supply & fixing PVC (SWR) bends any radius 110 mm dia complete all as specified and directed. .

Supply & fixing PVC (SWR) 'Y'/ 'T' junction (double/ single), equal or unequal (any radius), 110 mm bore, fixed to wall or laid in floor complete all as specified and directed.

Supply & fixing PVC (SWR) pipe 75mm bore size for rain water pipe conforming to IS : 1984, incl standard PVC clamp & imbedded in PCC block incl jointing of pipes complete inclduing taking down all pipes all as specified & directed by Engr-in-Charge

Supply & fixing PVC bends 75 mm bore any radius complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 75mm bore PVC (SWR) vent cowl, complete all as specified

Supply & fixing for 75mm bore PVC (SWR) multi-floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by the Engineer-in-Charge

Supply & fixing PVC (SWR) gully trap 125/110 mm,setting and jointing with solventcement Square or round type P or S trap complete all as specified and directed

Supply & fixing stainless steel grating doom 125 mm dia (min weight 40 gms) complete as specified and directed.

Supply & fixing stainless steel grating doom 100 mm dia (min weight 40 gms) complete as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide & not exceeding 1.5 metre in depth for foundations of manholes, sewerage pipe lines etc and not exceeding 10 sqm on plan including getting out in soft/ loose soil complete all as specified and as directed by Engineer-in-Charge .

Demolition and breaking up drain pipes SGSW, AC or reinforced concrete pipe upto and including 150 mm bore pipes, complete all as specified and directed by Engineer-in-Charge.

Material & labour for PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) concrete bed to drain pipe including packing under & haunching against the sides of pipe 150 mm dia ( internal) after the pipes are laid and tested in trenches, complete all as specified and directed by Engineer-in-Charge.

Material & labour for 150 mm dia (internal) Reinforced concrete pipes, class NP2, laid and jointed complete with collars laid in trenches & jointed, complete all as specified and as directed by Engineer-in-Charge .

Demolition of cement concrete of any description in any position not exceeding 15 cm thickness, complete all as specified and as directed by Engineer-in-Charge .

Material & labour for cement concrete 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) for foundations, fillings & mass concrete, sub base, plinth protection, complete all as specified and as directed by Engineer-in-charge.

Material & labour for cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) for manhole benching, flooring and coping, complete all as specified and as directed by Engineer-in-charge.

Supply & fixed in repair SFRC (Steel fibre reinforced concrete) cover and frame (heavy duty HD-20 grade designation) size of cover 0.70 m x 0.70 m conforming to IS 12592, fixed in cement cocrete 1:2:4, complete all as specified and directed by Engineer-inCharge.

Returning/filling in including spreading, leveling, watering & well ramming in layers not exceeding 25 cm thick each, complete all as specified and as directed by Engineer-in-Charge.

Removal of excavated material to a distance not exceeding 50 metre and depositing where directed not exceeding 1.5 metre above the starting point, complete all as specified and as directed by Engineer-in-Charge .

Material and labour cutting into existing manholes/septic tank for connecting new drain upto 150mm internal dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round to 3/4 section) in cement concrete (1:2:4) type B1 smooth finished and reforming benching as required complete all as specified and directed by Engr-in-Charge

Material & Labour for 35mm thick precast cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in louvers and jallies/Jaffari (measured solid) including all moulding and MS wire but excluding frame and set in cement mortar (1:4) including necessary form work including taking down old broken/unserviceable jalli, complete all as specified and as directed by Engineer-in-charge.

E/M Works

Taking down carefully unserviceable copper / aluminum point wiring (light, fan, socket) complete including existing conduit pipes and removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, light fittings etc and removing the retrieved materials from site including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and directed.

Material & Labour point wiring with 1.5 sqmm single core PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non-metallic PVC conduit (medium grade) surface on wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) including modular metal flush box & modular cover plate with frame suitable matching colour of required module for mounting or housing switches, socket outlets, fan regulators, etc. including blanking plates & all other fixing accessories for one light/fan/call bell/exhaust fan point controlled by one 5/6 Amps switch and including cutting chases (as required) and making good surfaces to match with adjoining surface complete all as specified and directed.

All as item No 132 here in before but for one socket outlet 5 pin 5/6 Amps 250 Volts flush type on same board complete all as specified & directed

All as item No 132 here in before but for one socket outlet 5 pin 5/6 Amps 250 Volts flush type on Independent board but not below the swtich board complete all as specified and directed

All as item No 132 here in before but for one socket outlet 6 pin, 6/16 Amps, 2 in 1 with cable 2.5 Sqmm multistranded copper conductor FRLSH cable on independent board including provision of 2.5 Sqmm PVC insulated copper conductor FRLSH cable continuos as earth wire connected to earth dolly, conductor etc

All as item No 132 here in before but for one bell point controlled by one bell ush on independent board.

Supply and fixing switch 1 way 6A, including its suitable module type, internal plates and frame cover with all connected acessories complete all as specified and directed.

Supply and fixing switch 1 way 6A bell push, including its suitable module type, internal plates and frame cover with all connected acessories complete all as specified and directed.

Supply and fixing switch 15/16 with suitable module type, internal plates and frame cover and its connected acessories complete all as specified

Supply and fixing socket outlet multipurpose, 2 in 1, 5 pin, 5/6 Amps,in suitable module type complete all as specified.

Supply and fixing socket outlet multipurpose , 2 in 1, 5 pin, 15/16 Amps in suitable modular , flush type complete all as specified

Supply and fixing ceiling rose surface type polycarbonate, isolated body two to three terminal, topline series 20 x 50mm, 6 Amps, complete all as specified.

Supply and fixing electric Bell, ding dong type 230 Volt AC supply complete all as specified.

Supply and fixing modular stepped type electronic fan regulators flush socket type complete all as specified and directed.

Supply and fixing lamp holder PVC/polycarbonate type with back plate suitable for batten fitting with LED bulb 9W complete all as specified and directed.

Supply and fixing in replacement of wall mounted LED fitting 1 x 20 watt, 6000k, 4 ft complete with square profile batten, environment friendly , energy efficient complete with all fittings, connections all as specified and directed.

Supply and fixing in replacement of light fitting of 9/10 watt, 6000 K , linear & compact with decorative grey end caps, polycarbonate body and ribbed opal diffuser complete with lamp and all other accessories fitting arrangement including electric connection connecting with using flexible copper wire twin core upto ceiling rose/connector all as specified and directed.

Supply and fixing in replacement of recessed LED ceiling light with wide light window for maximized glare free output suitable for 600x600mm and ceiling cutout 595x595mm modular grid/POP ceiling complete fitting with separate electronic driver and high brightness SMD LEDs 36 watt, 6000K and one No extra LED driver along the fittings including connecting electric connection, including taking down existing unserviceable old fitting any type complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of building security light die cast ast aluminium IP 66 roadway luminaire with high power LED of 25 to 35 watt with toughened glass complete with suitable GI for security light fitting fixing to wall/column & electrical connection to the light fitting providing 1.5 mtr long twin core round copper conductor cable of suitable size and testing including taking down existing unserviceable old light fitting any type complete all as specified and directed.

Supply and fixing in replacement sub main wiring complete with two single core 6 sqmm, 1100 volts grade PVC insulated, multistranded copper conductor FRLSH cable in and including PVC concealed conduit (medium quality ISI marked) and cutting of chases in wall including 6 sqmm single core copper earth wire to common earth and connecting to earth dolly complete all as specified. Note :- Three runs of cable and one run of conduit shall be measured as one unit.

Supply and fixing in replacement sub main wiring complete with two single core 6 sqmm, 1100 volts grade PVC insulated, multistranded copper conductor FRLSH cable in and existing PVC concealed conduit (medium quality ISI marked) and cutting of chases in wall including 6 sqmm single core copper earth wire to common earth and connecting to earth dolly complete all as specified. Note :- Three runs of cable and one run of conduit shall be measured as one unit.

Supply and fixing in replacement sub main wiring complete with two single core 4 sqmm, 1100 volts grade PVC insulated, multistranded copper conductor FRLSH cable (ISI marked) in and including PVC concealed conduit (medium quality ISI marked) and cutting of chases in wall including 6 sqmm single core copper earth wire to common earth and connecting to earth dolly complete all as specified. Note :- Three runs of cable and one run of conduit shall be measured as one unit.

Supply and fixing sheet metal enclosures made out of CRCA mild steel sheet, IP-43 protection, flush mounted for metal door, powder coated DB, V TPN 4 way, 415 V AC with 200 Amps rated bus bar, double door, dust and vermin proof suitable for incorporation of Incoming MCCB and outgoing MCB SP/TP and earth & neutral bus bar etc incl taking down old unserviceable DB all as specified and directed.

Supply and fixing sheet metal enclousers made out of CRCA mild steel sheet, double door, powder coated DB SPN 8 way 240 Volt, 200 Amps rated bus bar, dust and vermin proof suitable for incorporation of MCB's and isolators etc complete including taking down old unserviceable DB all as specified and directed

Supply and fixing MCCB 4 pole of rating 100 Amp, Icu 16 KA, thermal magnetic based complete all as specified and directed

Supply and fixing MCB SPN 63 Amps, 10 KA, B Curve, 230 V AC,50 Hz including necessary attachment complete all as specified and directed

Supply and fixing MCB SP 6 to 40 Amps 240, 10 KA B curve complete all as specified and directed

Supply and fixing of exhaust fan steel body 300 mm sweep (BEE, 5 star rated) with louvres, 230V, single phase AC supply, hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface as per existing surfaces, and connection to fan with suitable flexible twin core round copper wire complete all as specified and directed by Engineer-in-Charge. Note :- (i) Srl Number of exhaust fan and 'GE North BTD' shall also be writing on fan with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account, Srl number will be issued by Engineer-in-Charge. (ii) Exhaust fan installed/hanging at site as directed by Engineer-in-charge (from market to AGE E/M store/AGE E/M store to sites /Location, all conditions will be the responsibility of contractor and nothing extra will be admissible on this account.

Supply and fixing of BLDC (Brushless direct current motor) ceiling fan 5 star rated, complete with blades, down rods, and accessories, 230 Volts, 1200mm sweep, Min air delivery 210 CFM with service value 6.00 BEE, including electrical connection providing twin core round copper conductor cable of suitable size, complete all as specified and as directed by Engineer-in-Charge. Note :- (i) Srl Number of ceiling fan and 'GE North BTD' shall also be writing on fan with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account, Srl number will be issued by Engineer-in-Charge. (ii) Ceiling fan installed/hanging at site as directed by Engineer-in-charge (from market to AGE E/M store/AGE E/M store to sites /Location, all conditions will be the responsibility of contractor and nothing extra will be admissible on this account.

Supply and fixing in replacement of corroded GI pipe (light grade) of size 40mm for hanging of ceiling fan of approx miniumum length 5 Mtr each suitable for bearing capacity of hanging of a ceiling fan including arrangements of ceiling fan hooks and making holes on existing wall for fixing of pipe and its cement finishing work all as specified and directed by Engr-in- Charge

Supply and fixing in replacement sheet metal enclosure with two pin & earth plug and socket (industrial type DB) with and including one MCB SPN, B curve type capacity 25 Amps, 10 KA complete all as directed

Material and labour for sand filling in trenches including watering and consolidation complete all as specified and directed by Engr in charge.

Material and labour for sub class "B" brick laid in trenches for cable protection and laid perpendicular to the length of cable.

Supply, laying & testing in trenches, along poles/ walls LT cable XLPE insulated armoured, heavy duty electric cable, 1100 volts grade, cross sectional area 35 sqmm 3.5 core including taking out old unserviceable cable of any size from trenches/ along poles/ walls complete all as directed. Note :- Excavation& earth work, sand cushioning and brick protection shall be measured and paid for separately.

Taking down ceiling fan from site and keep in safe custody/store for reuse and fixing the same painting after completion of building plastering works complete all as directed by Engineer-in-charge. If any damage of fans at the time of transportation/deposit to store the contractor will responsible the same including hanging the same after completion of ceiling work refix the fan. Provision of connection wires and fixing arrangements are included in rates.

Supply and fixing of exhaust fan steel body 450 mm sweep (BEE, 5 star rated) with louvres, 230V, single phase AC supply, hanging on wall with 4 Nos steel fastners 10mm dia 100mm long and making good the disturbed surface as per existing surfaces, and connection to fan with suitable flexible twin core round copper wire complete all as specified and directed by Engineer-in-Charge. Note :- (i) Srl Number of exhaust fan and 'GE North BTD' shall also be writing on fan with red colour permanent marker, cost for the same shall deemed to be included in the quoted unit rate, nothing shall be paid extra on this account, Srl number will be issued by Engineer-in-Charge. (ii) Exhaust fan installed/hanging at site as directed by Engineer-in-charge (from market to AGE E/M store/AGE E/M store to sites /Location, all conditions will be the responsibility of contractor and nothing extra will be admissible on this account.

Material and labour for Earthing complete with galvanised iron earth plate electrode of size 60cm x 60cm x 6.3mm buried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metre below normal ground level, connected to and including earth continuity GI wire 4 mm (upto test point from earth plate i.e. 7.5m min) by means of GI bolts/nuts/washers and including protected by 15mm dia GI light grade protection pipe from earth plate to test point, including making of test point. Earth plate shall be surrounded by packed layer of char coal/coke & salt all around bottom and top with alternative layer. 20mm GI light grade pipe for watering (should be 10cm above GL) and including socket, plug, funnel, wire mesh, RCC cover and (including steel for cover) PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) as in earthing pit including necessary form work, excavation & earth work, all as specified & shown in electrical plate No. 3 of SSR (Part – I) including taking out/dismantling old unserviceable earthing system complete all as directed by Engineer-in-charge. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner.

M/S SAI BUILDERS

SAPNA BUILDERS

V K CONTRACTOR

M/S VIAJY BUILDERS & DEVELOPERS

K L JINDAL AND CO.

MODERN ENTERPRISES

M/s GURFATEH BUILDERS