REPAIR/MAINT OF SUMMER AND COOLING APPLIANCES AND GEYSER ZONE-I AND II AT CANTT UNDER GE (I) KANPUR

Amount

Repair, maint and making the continuity of supply after rectifying the defects of the ceiling fan, exhaust fan, wall fan, desert cooler, geyser, water cooler, refrigrator, ACs etc. including providing of small pieces of electrical wire of size 0.75 to 4 Sqmm twin/three core and length not exceding 1 mtrs and all types of screws, nuts, bolts & washers as required at site complete all as specified and directed. (Note :- (i) any accessories found unserviceable that shall be replaced & paid under respective items of this Sch. (ii) Contractor/ superviser of contractor will collect complaint slip on daily morning from MES complaint cell and deposit the same after rectify on next day morning (iii) Complaint slip book, registers as per sample will be provided by the contractor complete all as specified and directed.

Disconnecting electrically, taking down existing ceiling Fan any type and capacity with due care, dismantling blades for repairing with all accessories complete all as specified and directed.

Assembling the ceiling fan any type with blades at site and hanging on ceiling /wall refixing after getting rapaired complete with all accessories complete all as specified and directed.

Strip opening of AC ceiling fan 230 volts any make /type/size for carrying out repair/greasing / oiling, re-assembling, replacing rubber reel, fixing clamp, bolts and nuts with lock pins and testing complete all as specified and directed. Note :- 1. Repairs will be measured and paid separately under respective items.

Rewinding of AC ceiling fan motor 1200/1400 mm sweep any make/size with super enamelled copper winding wire with gauge including cutting of old burnt winding. Sleeve work varnishing with `B' class insulation varnish, greasing ,connection with flexible wire of appropriate size two core copper wire upto connector block complete all as specified and directed.

S&F fan capacitor AC 440 volts 4 mfd 50HZ complete all as specified and directed.

All as per srl item No 6 above but 2.5 mfd complete all as specified and directed.

M&L for repairs, alignment grinding to shaft, remetalling & finishing complete all as specified and directed.

S&F ceiling fan shaft of standard size including taking out old shaft, complete all as specified and directed.

Supply and fixing in replacement fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically complete all as specified and directed.

Disconnecting electrically, taking down existing exhaust Fan any type and capacity with due care, dismantling blades for repairing with all accessories complete all as specified and directed.

Assembling the exhaust fan any type with blades at site and hanging on ceiling /wall refixing after getting rapaired complete with all accessories complete all as specified and directed.

Strip opening of exhaust fan any size / make / sweep for carry out repair/greasing, oiling work, re-assembling, replacing rubber reel, fixing clamp, bolts and nuts with lock pins and testing after carrying out the repair, complete all as specified and directed.

Rewinding of exhaust fan motor any size, from 225 to 450 mm sweep with supper enamelled copper wire as required including necessary cutting of old burnt winding wire, cleaning of slots, greasing and provision of necessary threading/sleeve work and taking out connection in lead with PVC copper wire of appropriate size upto connector block complete all as specified and directed.

M&L in replacement of ball bearing any No suitable for ceiling fan upto 1400mm sweep complete all as specified and directed.

Replacement of ball bearing for exhaust fan upto 450mm sweep complete all as specified and directed.

Cleaning thoroughly ceiling fans 48"/56" (1200mm / 1400mm) sweep with Kerosene Oil and spray painting with spray gun including preparation of surfaces, and writing MES No after painting at site complete all as specified and directed.

Cleaning thoroughly exhaust fan 225 mm to 450 mm sweep with Kerosene Oil and spray painting with spray gun including preparation of surfaces, and writing MES No after painting at site complete all as specified and directed.

S&F in replacement of fan blade set plastic suitable for exhaust fan 225 to 450 mm sweep, complete all as specified and directed.

S&F in replacement of fan blade set steel 1200/1400mm sweep complete (as per sample) and all as directed by Engineer-in-Charge suitable for ceiling fan complete all as specified and directed.

S&F in replacement of down rod for ceiling fans made out of 15 mm dia MS pipe, medium grade duly threaded/pin complete all as per sample of size 45 Cm long complete all as specified and directed.

All as per item No 21 above but of size 1 Mtrs long complete all as specified and directed.

All as per item No 21 above but of size 1.5 Mtrs long complete all as specified and directed.

All as per item No 21 above but of size 2 Mtrs long complete all as specified and directed.

All as per item No 21 above but of size 3 Mtrs long complete all as specified and directed.

All as per item No 21 above but of size 4 Mtrs long complete all as specified and directed.

Supply and fixing lower and upper canopy of fans of ceiling fans of suitable size required at site complete all as specified and directed.

M&L for 40 mm bore galvanised iron tubing medium grade fixed to walls or hanging the fan including making hole and making good the disturbed surface by filling with PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate, plastered the surface and match the periodical such as oil bound distemper, white/colour wash etc with exisiting one complete all as specified and directed.

All as per item No 28 above but of GI pipe of size 50mm bore complete all as specified and directed.

M & L for providing PVC rounded 3 core 0.75 sqmm copper cable and making necessary connection complete all as specified & directed.

All as per item No 30 but copper cable of size 1.5 Sqmm complete all as specified and directed.

All as per item No 30 but copper cable of size 2.5 Sqmm complete all as specified and directed.

M & L for taking down/out desert cooler from existing place and removing old paint from the body of desert cooler and applying painting on desert cooler external body, fan and pump with a coat of synthetic enamel grey paint , internal body with a coat of synthetic enamel black paint with brush painting at site after proper dusting cleaning and scraping old painted surface and refixing on same/other location after painting complete all as specified and directed.

M & L in replacement of side panels of desert cooler made out of 22 SWG mild steel sheet of size not more than 0.70x0.80 mtr to match with existing cooler as per sample complete with jalli, wood wool pad , fastners painting with two coat of synthetic enamel paint over a coat of primer etc complete all as specified and directed.

Supply and fixing in replacement of water lifting pump submersible type 220 -240 Volts 50 HZ as per sample complete all as specified and directed.

Supply & fixing in replacement of kit fan motor of desert cooler as per sample, 230 volts complete with blades, fixing legs, nuts, bolts, washers etc of complete all as specified & directed.

S&F in replacement of ready made wood wool pad size as required at site of 15 mm thickness, made out of chicken wire mesh filled with fine quality wood wool and stitched with GI wire for desert cooler of any make & size complete all as specified & directed.

M & L for disconnecting, dismantling, refixing and rewinding of kit fan motor upto 450 mm sweep of desert coolers 230 volts AC 50 C/S with super enamelled copper conductor wire of existing gauge as original including replacement of bush -02 Nos shaft -01 No ring-01 No & clamp-04 Nos complete all as specified & directed

S & F of desert cooler stand using angle iron (40 x 40 x 6 mm) making square type platform of min size 800 x 800mm and fixing through two angle iron piece for horizontal support and two angle iron piece for 45 degree angle vertical support into the walls of any type / height as required on site by means of required nuts, bolts, fastners, welding work etc to form a platform suitable for fixing the desert cooler of any size & type compete all as specified and directed. Note: Angle iron should be painted with a coat of red oxide primer and two coat of synthetic enamel paint. Minimum 20 cm length of the angle iron should be inserted into the wall and fixing the same through required PCC work. Cutting chases in walls required for fixing the angle iron support shall be finished with cement mortar 1:4 and surface shall be matched with existing surface by using putty, plaster of paris etc. and applying finishing coat of existing treatment shall be deemed to be included in the unit rate quoted by the contractor.

M&L for dismantling, taking out old u/s clamp and fixing with new clamp for kit fan motor of desert cooler as per site requirement with nuts & washers complete all as spfd and directed..

Disconnecting, dismantling old u/s indicator lamps and replaced with new all as spfd and directed.

Dismantling old PVC Water distributor four way and refixing with new as per sample and all as spfd and directed.

S&F in replacement of existing UNSV desert cooler blade as per sample and fix in the desert cooler complete all as specified and directed.

Disconnecting, dismantling and taking out old u/s storage type water heater geyser of cap 25/35 Ltrs from wall for repair at site complete all as specified and directed.

Fixing only storage type water heater geyser on wall after reapir and replacement of old unserviceable with gutties/anchor bolts or nuts & bolts and fixing the same in existing /other location complete all as specified and directed.

M&L for spray painting of outside surfaces of geyser with two coats of white synthetic enamel paint after preparing surface with and including writing MES No. complete all as specified and directed.

M&L for opening the geyser and replacement of glass wool for insulation of geyser of 25 to 50 ltrs capacity of any make / type complete all as specified and directed.

S&F in replacement of PVC flexible connection of length 600 mm with two brass adopter as per existing sample suitable for carrying hot / cold water, fixed one end at geyser inlet and other to outlet water supply point complete all as specified and directed.

M&L for disconnecting, dismantling old u/s thermostat switch of geyser 25 to 50 ltrs capacity and replaced with new as per sample with temperature range adjustable from 25 to 90 degree centigrade, superior quality 20 Amps rating, 220 Volts AC supply as per sample complete all as specified and directed.

M&L for disconnecting, dismantling old u/s heating element of cap 2 KW and replaced with new and testing on completion as per sample complete all as specified and directed.

All as per item No 52 above but heating element of capacity 1.5 KW complete all as specified and directed.

M&L for dismantling old u/s syphon assembly of geyser 25 to 50 ltrs ltr capacity and replaced with new stainless steel syphon as per sample and complete all as specified and directed.

M&L for dismantling old u/s inner tank of geyser and replaced with new stainless steel inner tank suitable for 25 to 50 ltrs ltrs capacity geysers of 22 SWG and hydraulically tested at 22.5 PSI pressure maintained at 90 degree centigrade as approved complete all as specified and directed.

M&L in replacement of modular single pole and neutral enclousere with a top pin, earth plug and socket copmlete with one SP MCB 20 Amps, 240 Volts complete all as specified and directed.

S&F in replacement of pressure release valve with inlet coupling of superior quality as approved complete all as specified and directed.

S&F in replacement of plug top 15 Amps all as spfd and directed.

S & F in replacement of indicator LED bulb square / round type complete with necessary connection wire of red & green colour all as spfd and directed.

S&F of ceiling fan clamps for fixing with fan rod incd nut, bolt, lock pin, rubber real complete all as specified & directed.

S&F of hook for hanging of fan on ceiling of suitable shape of mild steel flat iron with suitable size nuts, bolts & washers complete all as specified & directed.

Dismantling and taking down old unserviceable Fan and depsited in MES Store yard & Supply, fixing and testing ceiling fan, white colour Energy saver 1200mm sweep (not exceeding 40 watt), 230 volts single phase complete Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) alongwith Remote and down rod, adequate size of clamp, making electric connection with PVC rounded 3 core 1 sqmm copper cable from ceiling rose to ceiling fan connector, including writing MES No. in black synthetic enamel paint / engraving with tool complete all as specified and directed.

Disconnecting electrically, taking down, dismantling, opening the cover of AC/Split and taking out and servicing of window type air conditioner cap 1.5/ 2 Ton capacity including cleaning / removing all dust / mud, oil and other foreign particle from grill, filter, condenser fin, evaporator fin including opening cover, peripheries and whole body using detergent solution or chemical solution and refitting all parts and fixing the same in existing/other location complete all as specified and directed.

Disconnecting, dismantling, opening the cover of AC and removing unserviceable / defective parts from the window Split AC of 1.5 / 2 Ton capacity including necessary welding with existing refrigerant pipe, supply & charging refrigerant gas and testing complete all as specified and directed. Note: (i) All spares such as sealed compressor, fan motor, relay, capacitor, over load relay shall be measured and paid separately if required under respective item of Schedule ‘A’. (ii) If any item required to make equipment functional like capillary copper pipe etc is deemed to be included in unit quoted rate. (iii) Old unserviceable hermetic sealed unit and other materials obtained from the window type AC will be accounted under Schedule of credit and same shall become the property of the Contractor

S&F in replacement of cooling coil of window type AC any cap up to 2 ton complete all as specified and directed.

S&F in replacement of front grill of window AC suitable for 1.5/2 ton cap as per sample complete all as specified and directed.

S&F in replacement of rotary type sealed compressor of window AC 1.5/2 Ton cap as per sample complete all as specified and directed.

S&F in replacement of Air blower motor as per sample suitable for window/split type AC of 1.5/2 Ton capacity single phase as per sample complete all as specified and directed.

S&F in replacement of starting capacitor suitable for window/split AC of rating 45 - 100 Mfd as per sample all as spfd and directed.

S&F in replacement of starting relay suitable for Window/split AC of capacity 1.5 / 2.0 Ton complete all as specified and directed.

S&F in replacement of thermostat switch as per sample for window/split type AC of 1.5 /2.0 Ton capacity complete all as specified and directed.

S&F in replacement of condenser fan blade suitable for window/split type AC of any make & capacity all as spfd and direceted.

M&L for minor denting work to window type air conditioners of 1.5 / 2 Ton capacity including applying spray painting with a coat of synthetic enamel paint of required shade complete all as specified and directed.

S&F in replacement of sealed compressor, rotary type, of any make as per sample suitable for split type AC of 1.5/2 Ton capacity all as spfd and directed.

S&F in replacement of Inlet / outlet control valve for outdoor / indoor unit of suitable size, of any make & any type all as spfd and directed.

S&F in replacement of discharge grill of outdoor unit of any size and type for split AC’s all as spfd and directed.

Supply and fixing in replacement of defective remote control hand set with "AAA" batteries for window/split type AC's, of any model / make complete all as specified and directed.

Supply and fixing in replacement of display indication on LCD screen assembly mounted on indoor unit (cooling unit) for split type AC’s, of any model / make complete all as specified and directed.

Supply and fixing of micron filter suitable for window / split type AC of 1.5 Ton capacity complete all as specified and directed.

Supply and fixing of copper tube as per existing and site requirement complete all as specified and directed.

Supply and fixing of condenser / cooling coil for air conditioner of suitable size complete as per site requirement and as directed.

Disconnecting, dismantling and taking out indoor and outdoor unit of split type AC with cooling tubing and other accessories with carefully and deposited to MES store yard complete with outer/inner unit, copper tubing, drain pipe and remort all as spfd and directed.

M&L for fixing/installation of split AC inner/outer or both unit as received from item No 86 with all accessories and making all coonection of copper tubing/drain and electrically and testing on completion all as spfd and directed. Note : Refrigrant and other connecting items i.e copper tube/ drain pipe will be measured and paid seperately under respective item if required.

supply and fixing in replacement of deoxidized annealed copper tube of as per sample including brazing etc. complete all as specified and directed.

supply and fixing in replacement of foamed polythene insulating pipe of 18 mm internal dia and 8 mm wall thickness complete all as specified and directed.

supply and fixing in replacement of foamed polythene insulating pipe of 8 mm internal dia and 7 mm wall thickness complete all as specified and directed.

S&F in replacement of Main control circuit (PCB) for window/split type AC's, of any model / make complete all as specified and directed.

S&F in replacement of PVC flexible drain pipe 15mm to 25mm dia all as spfd and directed.

M & L for flushing, pressurising the system, leakage testing, vacuumization and charging with refrigerant R -22 / R-134a/R-410 (suitable as per requirement) after rectifying leakage in the system vaccumising and dehydration as per standard practice including testing in all respect for window / split type air conditioner 1.5 / 2.0 TR cap at site / contractor's workshop including any welding / repair work reqd at site complete all as specified and as directed.

Supply & fix in concealed or fixed on wall of rigid non-metallic PVC conduit medium grade of size 20/25 mm dia inclusive of all tees, bends, elbows, reducers, bell mouth tube ends for drain of AC all as spfd and directed.

Supply and charging refrigerant R-22/R134a/R410 as per type of ACs for any type of gas filling the AC/Refrigeritor/water cooler/deep freezer etc complete one time for topping up or making full qty including plugging the leakage/ welding / repair work reqd at site complete all as specified and as directed.

Disconnecting, dismantling old u/s compressor from refrigrator and replaced with new as per sample for the refrigerator of capacity 165 to 310 Ltrs including necessary welding with existing refrigerant pipe, supply & charging refrigerant gas including testing complete all as specified and directed.

Supply and fixing in replacement of Starting relay suitable for refrigerator of any make and capacity.

Supply and fixing in replacement of Thermostat suitable for refrigerator of any make and capacity.

Supply and fixing in replacement of PVC freezer door suitable for any size and capacity of the refrigerator complete all as specified and directed.

Supply and fixing in replacement of Magnetic rubber door gasket suitable for any size and capacity of the refrigerator complete all as specified and directed.

Supply and fixing in replacement of Copper liquid line filter two way / one way of refrigrator any type/capacity complete all as specified and directed.

Supply and fixing in replacement of Over load protector of size 1/6 HP to 1/8 HP of refrigrator any type as per site requirement complete all as specified and directed.

Supply and fixing in replacement of Capillary tube as per site requirement of refrigrator/water cooler any type complete all as specified and directed.

Supply and fixing in replacement of Bulb of refrigrator any type as per site requirement of complete all as specified and directed.

Supply and fixing in replacement of Ice tray twist type PVC of refrigrator any type complete all as specified and directed.

Supply and fixing in replacement of Condenser cooling coil suitable for refrigerator capacity min 165 ltr to maximum 310 ltrs complete all as specified and directed.

Supply and fixing in replacement of Vegetable basket suitable for refrigerator as per site requirement complete all as specified and directed.

Supply and fixing in replacement of Partition jalli /glass shelf suitable for refrigerator as per site requirement complete all as specified and directed.

Disconnecting, dismantling and taking out old u/s voltage stabilizer of cap 1 to 5 KVA and refixing the same in same/other location after repair incl all minor parts i.e wire, nut, bolt and washers etc all as spfd and directed. Note : Spare parts will be measured and paid seperately under respactive items.

Supply and fixing in replacement of Main relay of voltage stabilizer 1 to 5 KVA as per sample complete all as specified and directed.

Supply and fixing in replacement of Main control circuit (PCB) of voltage stabilizer 1 to 5 KVA as per sample complete all as specified and directed.

Supply and fixing in replacement of replacement of sensor transformer of voltage stabilizer 1 to 5 KVA as per sample complete all as specified and directed.

Supply and fixing in replacement of voltmeter of voltage stabilizer 1 to 5 KVA as per sample complete all as specified and directed.

Supply and fixing in replacement of Time delay relay, 2-3 minute over / low voltage 180 Volts AC and high voltage 260 Volts AC of voltage stabilizer 1 to 5 KVA as per sample complete all as specified and directed.

Taking out old burnt winding of transformer and re-winding the same with super enameled copper winding wire (existing size) for 1 to 5 KVA voltage stabilizers including all necessary insulating material and testing complete all as specified and directed.

M & L for painting of voltage stabilizers with a coat of synthetic enamel paint of existing shade after proper cleaning and scraping out old painted surfaces and writing GE (I) Kanpur on voltage stabilizers in block letters with white synthetic enameled paint complete all as specified and directed.

Taking out water cooler of any make and type of capacity 40 / 80 / 150 ltrs from position and cleaning/serviceing the complete condenser coil and storage tank with chemical base solution and soda water including servicing, oiling of air blower motor, checking of electrical & water supply connection incl and re-fixing the same on its existing position after testing complete all as specified and directed.

Disconnecting, dismantling and taking out defective water cooler of any make and type of capacity 40 / 80 / 150 ltrs for repair all as spfd and directed.

M&L for fixing/installation of water cooler any type of cap 40/ 80/ 150 ltrs and making all electrical/water connection and testing all as spfd and directed

S&F in replacement of sealed compressor as per sample suitable for water cooler of capacity up to 40 / 80/ 150 Ltrs as per sample complete all as specified and directed.

S&F in replacement of Starting capacitor 40-60 Mfd / 60-80 Mfd / 80-100 Mfd as per sample for water cooler complete all as specified and directed.

S&F in replacement of Running capacitor 10-30 Mfd as per sample for water coller/ window ac/ split ac/refrigerator complete all as specified and directed.

S&F in replacement of Thermostat suitable for water cooler of capacity 40 / 80 / 150 ltrs as per sample complete all as specified and directed.

S&F in replacement of Starting relay of water cooler as per compressor requirement complete all as specified and directed.

S&F in replacement of Blower motor of water cooler with fan blade of capacity 1/10 to 1/35 HP as per site requirement complete all as specified and directed.

S&F in replacement of Over load protector of water cooler as per sample suitable for water coolers complete all as specified and directed.

S&F in replacement of PVC flexible pipe transparent 15 / 20 mm dia (as per sample) for water cooler complete all as specified and directed.

S&F in replacement of Push tap long body, cast copper alloy, chromium plated suitable for water cooler of capacity up to 150 ltrs (as per sample) complete all as specified and directed.

S&F in replacement of PVC float valve 15 / 20 mm dia with rod & ball for water cooler complete all as specified and directed.

S&F in replacement of Liquid line filter one way / two way for water cooler complete all as specified and directed.

Supply and fixing in replacement of waste washing tray including PVC pipe connection of existing shape & size for water cooler as required at site complete all as specified and directed.

S & F in replacement of condenser coil with copper tube and aluminium fins for water coolers suitable for up to 40 / 80/ 150 Ltrs capacity of any make and type complete all as specified and directed.

M & L for cutting out worn bottom and sheet base frame including mild steel legs from water coolers of any make and capacity and fixing the same with new plain galvanised iron sheet 16 SWG of existing size and new angle iron base frame and legs of existing size with and including necessary gas welding and providing nuts / bolts etc complete all as specified and directed.

M & L for minor denting work and applying a coat of spray painting to water cooler with synthetic enamel paint after proper scraping of old rusted painted surface complete all as specified and directed.

M & L for replacement of defective sealed compressor unit of 320 / 400 ltr cap deep freezer. The rates quoted by the contractor shall be inclusive of all charges like transportation fitting etc complete with necessary guarantee period including checking and rectification of any leakage in system and make in functional to entire satisfaction of EIC incl oiling, greasing, gas charging and testing complete all as specified and directed.

M & L for finding out leakage with the pressure testing of the condensor / cooling unit / compressor of deep freezer 320 / 400 Ltr cap including dismantling the same for recharging and stop leakage by brizing / soldering including charging the R-134A gas (or reqd type) to required level and testing the deep freezer for the entire satisfaction of EIC complete all as specified and directed.

M&L in replacement of modular single pole and neutral enclousere with a top pin, earth plug and socket copmlete with one SP MCB 20 Amps, 240 Volts complete all as specified and directed.

M & L for Writing SM / MES No. of Summer cooling appliances including Water coolers,refrigerators and Air Conditioners/Deep freezer with synthetic enamel paint of Make Asian paints Ltd. Or Stickers equivalent of approved color complete all as specified and directed.

AARADHIRAJ ASSOCIATES (BID ID -3143647)

S B ENTERPRISES (BID ID -3144330)