SPECIAL REPAIR TO BLDG NO T 20 TEMP SINGLE OFFRS ACCN OF SCC AND PROVN OF ENTRY GATE 01 TOILET BLOCK AND INTERLOCKING PAVER BLOCK AT CERTAIN LOCATIONS AT ARO UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Taking down chowkats or frames exc 1.50 Sqm but n.exc 4 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frames n.exc 1.50 Sqm with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutters and refixing in same opening of any descripition exc 1 sqm and n.exc 2sqm each complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

All as per ser item no 4.0 here-in-before but 20mm bore steel tubing complete all as specified and directed.

All as per ser item no 4.0 here-in-before but 25mm bore steel tubing complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10cm girth complete all as specified and directed.

S&F of tubes 15mm dia, medium grade, galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F of tubes 20 mm dia, medium grade, galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supplying and laying of 20mm dia cPVC pipes SDR 11 and plain CPVC SDR 11 fittings in trenches complete all as specified and directed.

S&F of tubes 25 mm dia, medium grade, galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off in the premises complete all as specified and directed.

M&L for screed bed or beding layer of mortar 15mm thick for laying floor finish in CM 1:6 complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surface backing coat to walll tile in CM 1:4 complete all as specified and directed.

M&L for vitrified glazed, light shade, tiles 8 to 10mm thick (square/rectangular), polished, of any shade area of each tiles exc 0.18 sqm but not exceeding 0.36 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for vitrified glazed, light shade, tiles 8 to 10 mm thick (square/rectangular) polished, area of each tiles exc 0.18 sqm but n.exc 0.36 Sqmas in vertical surfaces such as skirting, risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7-8 mm thick (square / rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm, in floor etc set and jointed in white or colour cement to match the surface of the tile complete all as specified and directed.

M&L glazed ceramic coloured tiles in vertical surfaces 350x250x7mm /450x350x7mm thick set and jointed in cement slurry with joint free including backing coat of 10mm thick in CM of 1:4 complete all as specified and directed.

M&L for non skid Ceramic coloured tiles 7-8 mm thick (square / rectangular) area of each tile exc 0.18 sqm but not exc 0.38 sqm, in floor etc set and jointed in white or colour cement to match the surface of the tile complete all as specified and directed.

M&L for non skid Ceramic coloured tiles 7-8 mm thick (square / rectangular) area of each tile exc 0.18 sqm but not exc 0.38 sqm, in vertical surfaces such as skirting, risers to steps, etc set and jointed in white or colour cement to match the surface of the tile complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting, grinding and polishing including over laid in screed 20 mm thick in CM 1:4 complete all as specified and directed.

Dismantling boarding any description fixed in, any position with nails complete all as specified and directed.

S&F in reapirs 18mm plywood grade BWR, type BB fixed with screws to timber frame work complete all as specified and directed.

S&F only 0.9mm thick decorative laminate, type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer instructions complete all as specified and directed.

S&F of 100 mm stainless steel handle, cast type, polished bright complete all as specified and directed.

S&F in repairs to cabinet hinges, soft close SS 8 crank complete all as specified and directed.

S&F in repairs to magnetic catcher for cupboard shutter complete all as specified and directed.

S&F of kitchen baskets with 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism kitchen capable of holding plates, cup, saucers,bowls and dongas with 500 mm car case depth of 558mm and height 100mm complete all as specified and directed. Make -: Life time-code: DSN 21 or equivalant as approved by GE.

S&F of kitchen baskets with 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism kitchen capable of holding plates, cup, saucers, bowls and dongas with 500 mm car case depth of 558mm and height 150mm complete all as specified and directed. Make -: Life time-code: DSN 21 or equivalant as approved by GE.

S&F of kitchen baskets with 100 % stainless steel, non - magnatic, multilayer chrome plated, argon welded, double sealed ball bearing mechanism kitchen capable of holding plates, cup ,saucers,bowls and dongas with 500 mm car case depth of 558mm and height 200mm complete all as specified and directed. Make -: Life time-code: DSN 21 or equivalant as approved by GE.

M&L for making good under cills and over archs, lintels and bressummers including all pinning where necessary in cement mortar in 1:6 complete all as specified and directed.

S&F of powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat, channel etc for fixing etc. complete all as specified and directed.

S&F of 4.8mm thick plain sheet glass ordinary quality nexc 0.50 sqm in each pane complete all as specified and directed.

S&F of stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F only to factory made single extruded WPC (WoodPolymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic aditives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance tospread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia andlength complete as per direction of Engineer-in-Charge complete all as specified and directed.

S&F of factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge complete all as specified and directed.

S&F of 35 mm factory made single extruded WPC (Wood Polymer Composite) solid plain Glazed shutter door of 35 mm size open rebated and prepared to receive gauze, etc.(without sash bars) edge of framing plain, chamfered or rounded, etc; size of members of shutters comprising of virgin polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge complete all as specified and directed. Note : Wiremesh Shall be measured and paid separetely.

S&F for pressed steel frames of size 165x60 mm for fixing of panelled and fly proof doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

S&f for factory made solid panel PVC door shutter 30 mm thick consisting of frame made out of M.S. tube for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colur PVC sheet for top rails, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fittet in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at sites as per specification & drawing complete all as specified and directed.

S&F of solid PVC door frame of size 50mmx47mm made out of 5mm prelam colour PVC sheet reinforced with MS square tube, complete all as specified and directed.

S&F of 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F of 125mm butt hinges, heavy weight, cold rolled mild steel and fixed, type C-21 complete all as specified and directed.

S&F of 100mm but hinges, extruded alluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F of 150 mm long aluminium handles, cast type, anodised fixed to shutters complete all as specified and directed.

All as per ser item No 45.00 here-in-before but 100mm long.

S&F of 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

All as per ser item No 47.00 here-in-before but 100mm long.

S&F of 300mm long, aluminium sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F in repairs vitreous china wash hand basin, white flat back of size 550 x 400mm excluding tap but including brackets/CP brass 32mm waste coupling and pipe complete all as specified and directed.

S&F in repairs 15 mm wash basin mixer, centre hole, mixing hot & cold water, fancy type, cast copper alloy, chromimum plated with capstan head, screwed down high pressure, screwed for iron pipe etc and fixed complete all as specfied and directed.

S&F in repairs health faucet (ABS Body) mild steel, chromium plated suitable for 15 mm dia pipe with 1.25 mtr long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F of chromium plated, grating doom 100 mm dia with waste hole complete all as specified and directed.

S&F of 10 ltrs capacity PVC low level flushing cistern, of make specified with inlet, float valve and handle including bracket with 32 mm dia PVC flush pipe complete all as specified and directed.

S&F in repairs PVC connection, 15mm size with PTMT nuts of length 450 mm fixing complete all as specified and directed.

S&F in repairs 15 mm stop cock, cast copper alloy, screwed down high pressure, chromium plated, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs 15 mm bib taps, cast copper alloy, screwed down high pressure, chromium plated, screwed for iron pipe and fixed complete all as specified and directed.

M&L for PVC (SWR), floor trap plain with grating including jointing with solvent cement of 75mm bore complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and directed.

S&F of PVC(SWR) pipes 75 mm bore, single socketed in any length with rubber rings joints laid in trenches complete all as specified and directed.

All as per item No 60.00 here-in-before but 110mm bore.

S&F of PVC(SWR), bend of bore 75 mm complete all as specified and directed.

S&F of PVC(SWR), bend of bore 110 mm complete all as specified and directed.

S&F of PVC(SWR), 75mm bore, branch piece single (Y) equal or unequal bend, the complete all as specified and directed.

S&F of PVC(SWR), 110 mm bore, branch piece single (Y) equal or unequal bend complete all as specified and directed.

S&F of PVC(SWR), 75 mm bore, junction single (single 'T') equal or unequal complete all as specified and directed.

S&F of PVC(SWR), 110 mm bore junction single (single 'T') equal or unequal complete all as specified and directed.

S&F of PVC(SWR) vent cowl, 75mm bore complete all as specified and directed.

S&F PVC(SWR) vent cowl, 110mm bore complete all as specified and directed.

S&F in repairs plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F of tubular towel rail chromium plated 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed.

S&F of vitreous china wash down water closet pan (pedestal pattern), white and trap including seat cover, fixing bolt, flush pipe, connection to drain (or out going pipe) and to flushing pipe, antisyphonage pipe, etc complete all as specified and directed.

S&F in repairs plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs 125mm, chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs stainless steel sink, 1.00mm thick for kitchen, with plug, washers and wastes/coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm with bowl size 410mmx 330mmx 160mm fixed complete all as specified and directed.

S&F in repairs stainless steel, 1mm thick, plate rack complete assembeled set of (Size: 31 x 36 x 10 inch) fixed with screws complete all as specified and directed.

S&F in repairs of PTMT waste coupling, 32 mm dia, half or full thread, complete all as specified and directed.

S&F in repairs of PVC waste pipe 900mm long, 32mm dia size, complete all as specified and directed.

S&F in reapirs soap dish holder of bootom Cp and glass holer for soap complete all as specified and directed.

S&F in repairs CP 15mm wall/sink mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs CP fancy type bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F of glass corner shelf, size nexc 250mm with CP bracket complete all as specified and directed.

S&F of sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repair of bore 15mm, angle cock, cast copper alloy screwed, fancy type, pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed complete all as specified and directed.

Taking down cement plaster, terrazzo/cement dado, skirting etc of any description on brick/stone walls, concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15 mm thick rendering in cm 1:4 on fair aces of bricks walls surface finished even and smooth without using extra cement including water proofing compound all as specified and directed. Note:- Water proofing compound will be measured and paid seperately.

M&L for 10 mm thick rendering in CM 1:6 on fair face of brick walls/ concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Supply only integral water profing compound complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coats of oil emulsion distemper over a coat of white cement based putty for as required smooth surfaces complete all as specified and directed. (Note : Putty shall be paid and measured separetely)

M&L for preparation of new plastered surface and applying two coat of exterior weather proof water base emulsion paint white/coloured over and including one coat of white cement based putty (where it is required) complete all as specified and directed.

M&L for complete removal of old decorated surface of wall and applying two coat of exterior weather proof water base emulsion paint white/coloured over and including one coat of white cement based putty complete all as specified and directed. Note : Putty shall be paid and measured separetely.

M&L for complete removal existing treatment and applying two coats of oil emulsion distemper over a coat of white cement based putty all as specified and directed. Note : Putty shall be paid and measured separetely.

M&L for 3mm thick wall care putty on wall/ceiling complete all as specified and directed.

Demolition of concrete in ground floors and pavings (un reinforced) nexc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for PCC 1:3:6 type C-2, 75 mm thick, using 40mm graded stone aggregate as in plinth protection complete all as specified and directed.

Demolition of brick work or stone masonery built in cement mortar complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:6 using modular bricks complete all as specified and directed.

M&L for brick work with fly ash bricks in CM 1:6 using modular bricks straight or curved on plan to any radius complete all as specified and directed.

S&F in repairs 20mm dia drepary rod decorative type, including brackets of approved quality as in complete all as specified and directed.

Dismentling of asbestos cement (corrugated ted, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F for mild steel, rolled section/tubular sections in purling, cross, beam, rafter, posts etc. incl connected cleats, hold fasts etc of grade conforming to Fe 410-W or Fe 310-O complete all as specified and directed.

S&F of mild steel, wind ties for roof truss including necessary drilling bolting as riveting etc and similar work to Fe 410-S or Fe 310-S complete all as specified and directed.

S&F of pre-painted galvalume aluminium zinc coating GI based corrrugated steel sheet 0.50 mm thick of any color having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self-tapping screws on angle iron frame of each side complete all as specified and directed.

All as per item No 104 here-in-before but plain sheeting complete all as specified and directed.

M&L for preparation of old painted surfaces of steel and iron surface of any description and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

S&F of framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-O or Fe 310-O complete all as specified and directed.

M&L for providing cement concrete type B1 1:2:4 (20mm graded stone aggregate) as in roof kerbs or mud stops, copings an levelling concrete etc slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for machine pressed precast concrete inter locking paver block (Reflective type) in any shape and size confirming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment over and including 50mm thick sand for laying of paver complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation, sub base etc complete all as specified and directed.

Cutting holes in brick walls exc half brick but not exc one brick in cement mortar ore cement lime mortor for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 using 20mm graded stone aggregate as required complete all as specified and directed.

Dismantling wall and ceiling boards(fibre, pulp,insultion, etc) or insulation boards/slabs/blankets,any thickness,including cover fillets complete all as specified and directed.

S&F of galvanised cold rolled steel section framed work size 600x600mm grid size 24x38x0.60mm Tee (bottom precoated) and 24x24x0.50mm thick wall angle galvanised cold rolled steel section incl expansions fasteners as in ceiling complete all as specified and directed.

S&F of 6mm thick asbestos free calcium silicate board of size 600x600mm fixed to frame of galvanised cold rolled steel frame work as in ceiling including applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for excavation in trenches n exc 1.5 m wide and n exc 1.5 m in depth beyond, for foundation, etc. or for shafts, wells , cesspits, manholes, pier holes etc n exc 10 sqm on plan and not 1.5 m depth and getting out soft/loose soil complete all as specified and directed.

Returning, filing in, excavated soil including spreading, levelling, watering and well ramming in layers not exceeding 25cm etc complete all as specified and directed.

Removal of excavated soil not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting points etc complete all as specified and directed.

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortor for 200 mm internal dia of pipe complete all as specified and directed.

M&L for reinforced concrete pipes, class NP-2, laid and jointed with collars of 200 mm bore of pipe complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 200 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for mild steel TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hoping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No. 123.00 here-in-before but for 6 to 8mm dia in stirrups, spacers and binders.

M&L for precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:4 complete all as specified and directed.

Dismantling water tanks of exc 500 litres but n.exc 1000 litre capacity and removing to store complete all as specified and directed.

S&F of 1000 ltrs capacity rotational moulded polyethylene water storage tanks 3 layers (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for earth work in excavation of any type of soil by mechanical means (Hydraulic excavator) means over areas (exc 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) in type B1 1:2:4 (using 20 mm graded stone aggregate) in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) in type B1 1:2:4 (using 20 mm graded stone aggregate) in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) in type B1 1:2:4 (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter with rough finished surface complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions square or rectangular in plan to provide rough finish surface to concrete complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick (horizontal or sloping) flat surfaces complete all as specified and directed.

S&F of framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S&F of rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. complete Fe 410-W (Gde E-250) quality A complete all as specified and directed.

M&L for mild steel of 1.00 mm thick, plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.

M&L for 50mm thick sand stone slabs in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, platform bases etc n.exc 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4 complete all as specified and directed.

M&L for preparing of newly plastered surface of walls and applying two coats of oil bound distemper over a coat of primer etc complete all as specified and directed.

M&L for preparation of old decorated plastered or unplastered surfaces and applying two coat of white wash on ceiling complete all as specified and directed.

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in hard dense soil complete all as specified and directed.

S&F of providing and laying 60mm thick rubber moulded factory made chamfered edge cement concrete glossy finish paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer and filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

S&F of vitreous china wash basin, white, flat back, size 450x300mm including PVC connections 15mm size with PTMT nuts of length 450mm, 32mm pvc waste pipe of suitable length and SS waste coupling, brackets, and cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F of vitreous china urinal half stall type, white with union for discharge pipe including waste pipe 450mm and urinal spreader (Minimum weight 60gms) fixing with 15mm dia pipe complete all as specified and directed.

S&F of vitreous china squatting pan, Orissa, pattern, size 580 x 440 mm white, with integral foot rests and flush pipes with PVC SWR P or S trap complete all as specified and directed.

S&F of CPVC pipe 25mm dia of grade SDR-11 (class-I) including all CPVC and brass fittings fixed to wall, floor or ceiling or laid in floors etc complete all as specified and directed.

S&F of 15mm bore CP stop valves/angle valve cast copper alloy fancy type, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F of 15mm bore dia CP stop valve/angle cock, but fancy type, chromium plated, with long shank and cup (concealed type) and fixed complete all as specified and directed.

S&F of PVC connection 15mm dia of length not less than 600mm with both ends, brass fly nut for water supply complete all as specified and directed.

S&F of chromium plated, two way bib tap 15mm dia complete all as specified and directed.

S&F of 15mm bore, fancy type, long body CP, bib tap of cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F of 15 mm tall body (min 140mm) CP pillar taps, cast copper alloy, with long screwed shanks and fly nuts, screwed for iron pipe and fixing complete all as specified and directed.

S&F of toilet paper holder with flat recessed type stainless steel complete all as specified and directed.

S&F of CP towel rail 600mm long premium quality, 20mm dia, fixed with and including CP brass screws complete all as specified and directed.

S&F of factory made single extruded WPC (Wood Polymer Composite) solid door Frames/chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant complete all as specified and directed.

S&F of factory made single extruded WPC (Wood Polymer Composite) solid plain or moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with and including 100mm SS butt hinges (min 03 Nos) and full body threaded star headed counter sunk S.S screws and fixing in the frame at site complete all as specified and directed.

S&F of 3mm thick figured glass with oil putty, ordinary quality not exc 0.5sqm in each pane complete all as specified and directed.

M&L for broken glass coping on top of walls in cement mortar 1:3 (minimum thickness of coping 40mm) complete all as specified and directed.

S&F in repairs galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain-ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. (each line wire to be measured) complete all as specified and directed.

Taking down carefully copper/aluminium point wiring concealed/ casing caping (light, fan, socket or power ponit) including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings, call bell and removing materials to store for keeping in safe custody or taking schedule of credit and making good disturbed surfaces of walls, floors, etc all as specified and directed.

Taking down of unserviceable old existing submain wire of any size all as specified and directed.

Taking down down of unserviceable distribution boards with MCBs all as specified and directed.

M&L for concealed point wiring for one light or one fan or one exhaust fan controlled by one switch complete with and includidng single core PVC insulated unsheathed flexible conductor FRLS cables 1.5 sqmm as per IS 694:2010, ISI marked, annealed multistranded copper conductor drawn through and including medium grade, machenical strees PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20mm noninal size including modular / non modular type all accessories/fitting / metal flush box / cover plate/junctiion boxes/ inspection cover etc ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 1.5 sqmm copper conductor PVC insulated, unsheathed flexible multistaranded copper conductor FRLS cable as continious earth wire connected to metalic body at one end and common earth dolly to other end including cost of cutting chase and making good to distrubed surfaces of wall with cement mortor 1: 3 including necessary plaster in cement mortor 1:3 with white wash / distemper/ other painting complete all as specifiecd and as directed. Note:-(i) cost of cutting chase and making good shall be included in the quated rates. (ii) Metal flush box, cover plate will be measured and paid seperately.

All as per ser item No 166.00 here-in-before but one socket outlet 5 pin 5/6 Amps on independent board controlled by one, one way switch.

All as per ser item No. 166.00 here-in-before but one socket outlet 5 pin 5/6 Amps on same board with other one, one way switch.

All as per ser item No. 166.00 here-in-before but for one switch socket combination 6 pin 5/15 Amps on independent board with wire of size 2.5 Sqmm and 2.5 Sqmm as earth wire.

All as per ser item No. 166.00 here-in-before but for socket outlet, 15/16 Amps on independent board with 4 Sqmm size cable and 4 Sqmm for continuty earth wire connected to common earth dolly.

S&F of modular switch, one way 6 Amp, one module, 240 volts complete all as specified and directed.

S&F of modular switch, one way, 16 Amp, one module, 240 volts complete all as specified and directed.

S&F of modular socket outlet 2-in-1, 2/3 pin, 6/16 Amps, 240 volts, controlled by one switch complete all as specified and directed.

S&F of modular socket outlet 2-in-1, 2/3 pin, 6 Amps, 240 volts, controlled by one switch complete all as specified and directed.

S&F of modular metal flush box of 6 module complete all as specified and directed.

S&F of modular metal flush box of 4 module complete all as specified and directed.

S&F of modular metal flush box of 3 module complete all as specified and directed.

S&F of modular white cover plate with frame of 6 module complete all as specified and directed.

S&F of modular white cover plate with frame of 4 module complete all as specified and directed.

S&F of modular white cover plate with frame of 3 module complete all as specified and directed.

S&F of sheet metal enclosures with socket plug top and MCB's with two pin and earth plug and socket complete with one single pole MCB 240 V grade 25/20 Amp complete all as specified and directed.

S&F of ceiling rose, 3 terminals 65x25 mm dia polycarbonate isolated complete all as specified and directed.

S&F of lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&f of modular fan regulator complete all as specified and directed.

S&F of 10 watt LED bulb, cool day light, 230/240V, AC complete all as specified and directed.

S&F of LED tube light fitting bright 18/20 watt slim elegant design and including connected with 3 core 23/0.0076 insulated copper wire from celing rose to fittting connector complete all as specified and directed.

S&F of modular bell push 6 Amp, one module, 240 volts complete all as specified and directed.

S&F of call bell, Ding Dong 230V, AC, single phase, ISI marked complete all as specified and directed.

S&F in replacement of building security light fitting complete with 36 watt IP 65 LED, type pressure die cast aluminium housing and heat resistant toughened glass with frame protection and better optics for uniform distribution complete fixed bracket made out of GI pipe 32 mm dia (light grade) 1.5 metre long and mild steel clamp and nut bolts washers and connected with twin core cable 1.5 sqmm from ceiling rose to fittings connector complete all as specified and directed.

Taking down and refixing of LED tube light fitting bright 18/20 Watt slim elegant design and including connected with 3 core 23/0.0076 insulated copper wire from celing rose to fittting connector complete all as specified and directed.

S&F of factory made epoxy powder coated Distribution Board TPN, 4 ways (VTPN MCCB DB) and space for MCCB as incomer, with metal door(IP-43 protection), fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including isolated Neutral Bar, Insulated busbar assembly, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockouts complete all as specified and directed. NOTE:- MCCB shall be measured and paid seperately.

S&F of MCCB 125 Amp, 3 Pole, breaking capacity 36 KA with complete electrical connections by appropriate size of copper lugs, complete all as specified and directed.

S&F in replcement MCB 6-32 amps, 10 KA, SP 240 volt, 'C' series complete all as specified and directed.

S&F in replcement MCB 40 amps, 10 KA, SP 240 volt, 'C' series complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode size 600X600X6mm thick burried directly in ground vertically to a depth not less than 2.25m deep below normal ground level with top edge of earth plate not less than 1.5m deep below normal ground level and connected to and including GI earth lead wire 4mm dia by means of bolts, nuts, check nuts & washers of galvanised iron and connected to test point all as shown in electrical plate No 3 of SSR part I-2009 and all as specified or indicated and testing on completion including excavation and earth work in any type of strata available at site, PCC (1:3:6) type C-1 using 20mm graded stone aggregate, earthing chamber, pre cast RCC slab 50 mm thick in cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate reinforced with welded steel wire fabric (XPM) weight not less than 4 kg/sqm funnel with GI watering pipe of 20 mm bore medium grade, wire mesh and lugs, GI protection pipe of 15 mm bore light grade up to 7.5 metre long all as specified and directed.

S&F of LED tube light fitting, two feet 10 watt, slim design, 230 volts, including connected with 3 core 23/0.0076 insulated copper wire from celing rose to fittting connector complete all as specified and directed.

Taking down/dismantling of storage type hot water geyser of 50/35/25 litre capacity from different locations by disconnecting inlet/outlet connections and depositing to AGE E/M SI Line store without any damage complete all as specified and directed.

Taking down carefully serviceable/unserviceable exhaust fans of any type/size from its position and depositing to AGE E/M SI Line store without any damage complete all as specified and directed.

Taking down carefully ceiling fans of any size from its position, and depositing to AGE E/M SI Line store without any damage complete all as specified and directed.

S&F in replacement of sub main wiring in PVC concealed conduit of required size two 4.0 sqmm PVC insulated multistrand copper conductor with one 4.0 sqmm PVC insulated multistrand copper conductor as earth continuity wire with including required size pvc casing caping as required dia but not less than 20 mm complete all as specified and directed. Note:- For the purpose of payment two runs of 4 sqmm conductors and one run of 4 sqmm conductor with casing caping will be measured as one length.

S&F of ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) without remote controller complete all as specified and directed.

S&F of exhaust fan, steel body AC single Phase, 230V of size 300mm sweep with, blades, and frame and louvers including cutting of hole in existing wall and resurfacing of disturbed area of wall complete all as specified and directed.

S&F of electric water heater, storage type, steel body with copper inner tank and heating element upto 2 KW, capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed.

S&F of LED ultra slim decorative aluminium casted edge ceiling light, recess mounting LED 2 x 2, luminaire 36 watt warm white in colour with all accessories internally pre-wired and including connecting with PVC insulated multistranded copper flexible cable 0.5 sqmm three core complete all as specified and directed.

S&F of LED tube light complete fitting 1x18 watt 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F of LED light fitting mirror type with high out put 2 feet, 10 watt 220 V AC connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F of LED lamp 10 Watt B-22 CDL complete all as specified and directed.

S&F in repairs DB, SPN 4 way, double door for MCB, 240 volt with suitable rated bus bar (IP-43) with enclosure blank plates for unused complete all as specified and directed.

S&F of MCB SPN suitable for 240 volts, AC supply 32 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA 'C' curve connection with suitable size copper lugs complete all as specified and directed.

S&F in replacement building security light fitting complete with 30 watt LED type pressure die cast aluminium housing and heat resistant toughened glass with frame protection and better optics for uniform distribution complete fixed bracket made out of GI pipe 32 mm dia (light grade) 1.5 metre long and MS clamp and nut bolts washers and connected with twin core cable 1.5 sqmm from ceiling rose to fittings connector complete all as specified and directed.

Excavation in trenches n. exc. 1.5 mtr in wide and n. exc. 1.5 mtr in depth for laying of underground cable and getting out in Hard/dense soil complete all as specified and directed.

Returning, filling in excavated soil in trenches including spreading, leveling, watering and well ramming in layers n. exc. 25 cm thick complete all as specified and directed

Removing of excavted soil to a distance n. exc. 50 mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

M&L for local sand dry, filling in trenches around under ground cable complete all as specified and directed.

M&L for providing of un-reinforced precast concrete cable cover class LV, Type 2, size 300mmx 180mm x 40mm laid flat dry for protection of under ground cable complete all as specified and directed.class,, flat,

Supply, laying and testing of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminum conductor of size 10 sqmm 2 core complete all as specified and directed. Note:- Excavation & earth work and pipe / sand / bricks for cable protection shall be measured and paid for separately under appropriate item of this schedule)

M&L for GI tubing, light grade" galvanized for protection LT Cable all as specified of size 40 mm bore complete all as specified and directed.

S&F of gun metal gate valve/glove valve of 20mm dia, ISI marked with iron wheel head screwed both end complete all as specified and directed.

S&F of 500 ltrs capacity rotational moulded 3 layer HDPE water storage tanks (Cylindrical vertical with closed top), hoisted and fixed in position all as specified in IS Code -12701-1996 including 20mm dia tank nipple complete all as specified and directed.

S&F of 20 mm PVC float valve ISI marked high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball complete screwed for iron pipe or brass furred and fixed with fittings such as (socket, nipple, union) etc complete all as specified and directed.

Deduct Schedule of credit (calculation will be done off line) Rs. 51594.00

M/S RAKESH TRADERS (BID ID -3380812)

sachinder singh (BID ID -3372525)

RAJPATI CONSTRUCTION (BID ID -3369103)

SHIV SHANKAR MISHRA (BID ID -3381031)