Special repair to Bldg No. T-10, T-16 and T-22 in Mil Stn Jaisalmer

Amount

Dismantling Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, all as specified & directed by Engr-in-charge.

Demolition of Cement concrete (Un-reinforced) of any description and in any position, all as specified & directed by Engr-in-charge.

Dismantling of Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar, complete all as specified.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

M &L rolled mild steel work in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated of quality Fe-410W (Gde E-250 quality A)

M&L for Precast cement concrete block masonry with solid blocks PCC Type C1 (1:3:6) (using 20mm graded aggregate) exc 10cm in width and setting in CM 1:6

M &L Squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in CM 1:6

S&F 50 mm thick sand stone slabs Jaisalmer pattern/colour in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc not exceeding 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar (1:4) complete all as specified & directed by Engr-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

M&L Screed bed or bedding layer of mortar 15 mm thick in CM 1:6 for laying floor finishes, complete all as specified and directed by Engr-in-Charge

M/L Cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate in floors, 40mm thick complete.

M&L Granite (of any type) tile 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing laid on complete all as directed by Engr-in-charge

M&L for Glazed ceramic colour tiles in vertical surface 350x250mmx7mm/ 450X350X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in CM 1:4.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick joint free tile square/rectangular area of each tile exceeding 0.06 but not exceeding 0.11 sqm, in floors etc. jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles, complete all as specfied and directed by Engr-in-charge.

S&F Non skid ceramic tiles 7 to 8 mm thick joint free tile area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specfied and directed by Engr-in-charge.

M & L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specfied and directed by Engr-in-charge.

M & L APP based polymeric membrane minimum weighing 3.5 Kg/Sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 160 gms/sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 Ltrs/Sqm by torched application including taking down of exisiting roof treatment in all respects, complete all as specified and directed. Roof treatment consist of as under:- (1) Applying 1 coat or bituminous primer conforming to IS-3384 @ 0.3 ltrs/Sqm (ii) laying of APP based membrane as specified thickness and weight. (iii) Applying 2 coat of Al paint @ 100 ml/sqm

Dismantling of wall and ceiling boards (fibre, pulp, insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

S & F Anodised aluminium snap grid of size 605 x 605mm frame work for false ceiling with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

M & L 12mm thick Gypsum board in ceiling fixed with screw as per manufacturer's instructions, complete all as specified and as directed by Engr-in-Charge.

Taking down chowkats or frames exc 1.50 Sqm but not exceeding 4 sqm each without taking off shutters from the frames including iron mongry.

Taking down chowkats or frames n.exc 1.50 Sqm each, without taking off shutters from the frames including iron mongry.

S&F butt hinges 75mm long stainless steel.

S&F Anodised aluminium alloy handles cast type, each 125mm long

S&F butt hinges 100mm long stainless steel.

S&F Anodised aluminium alloy handles cast type, each 150mm long

S&F Aluminium anodised, barrel tower bolts 125mm long of extruded section and fixed

S&F Aluminium anodised, barrel tower bolts 75mm long of extruded section and fixed

M&L for Anodised aluminium frame powder coated for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S & F Anodised aluminium door shutters with powder coating of any colour (Thickness or powder coating not less than 50 micron), aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified

S & F Anodised aluminium window and ventilator shutters with powder coating of any colour (Thickness or powder coating not less than 50 micron), fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S & F 4.8mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each pane, all as specified and as directed by Engr-in-charge.

S & F 4.8mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.50 Sqm in each pane, all as specified and as directed by Engr-in-charge.

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples, complete all as specified.

M&L for aluminium sliding track for Aluminium glass shutter and cupboards, complete all as specified and directed by Engr-in-charge

S&F slide roller for Aluminium door, window shutters and cupboards, complete all as specified and directed by Eng-in-Charge

S&F 12 mm Prelaminated Particle board, exterior grade, prelaminated both side with decorative choice laminations fixed with screws to timber frame work and alumunium frame complete all as specified and directed by Engr-in-charge

S&F in repair, Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed

S&F Aluminium 4 levers rebated mortice lock, vertical type, size 75 mm

M & L 50mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) as in plinth protection, all as specfied and directed by Engr-in-charge.

M&L in repair, Prelaminated Particle board 19mm thick, interior garde, prelaminated one side with decorative choice lamination & other side blancing white lamination, fixed with screws with handles, lock, magnets and hinges are per requirement, complete all as directed by Engr-in-Charge.

S&F PVC solid doors frame of size 50mm x 47mm made out of 5mm plane colour PVC sheet reinforced with MS tubes .

S&F factory made solid panelled PVC door shutter 30mm thick (style) consisting of frame out of MS tubes for top and bottom rails MS frame shall be covered with sheet moulded plain coloured PVC 'C' channel having a PVC sheets of 20mm width stuck inside with solvent cement for site and frame coloured PVC sheets for top rails as gap insert for top rails on either side and as gap insert for top rails and bottom rails pannelling of plain coloured PVC sheets to be fitted in the MS frame welded sealed to the site and rails with suitable PVC sheets beading and joints together with solvent cement in the frame at site as per specification. (PVC door shutter) complete all as directed.

Taking down cement plaster on brick or stone wall,etc including raking out joints, hacking for key, scrubbing down with water etc all as specifid and directed.

M&L for rendering 15mm thick on stone surfaces or other than fair faces of brick work or on one side of lathing in cement mortor 1:6, finished even and smooth without using extra cement complete all as specified.

M&L for 10mm thick rendering in cement mortar 1:6 on fair face of stone masonry surfaces,finished even and smooth without using extra cement complete all as specified.

M&L for prepration of new plastered wall surfaces of any description over 10cm girth or width, not otherwise described and applying two coat of Plastic emulsion paint over a priming paints plaster coat, complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of distemper oil emulsion over 3mm thick wall care putty, complete all as specified and directed.

S&F in repair 1000 ltrs capacity white colour three layer rotational moulded polythene water storage tank (Cylinderical vertical with closed top) hoisted and fixed in postion including taking down of old unserviceable water storage tank all as directed by Engr-in-Charge

S&F in repairs Ball valves 20 mm with high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipe and fixed min weight for 20 mm 210 gms, complete all as directed by Engr-in-Charge.

S & F in repairs 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repair, Bib tap chromium plated (ISI marked) cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule. (Weight not less than 400 gms) complete all as specified & directed by Engr-in-charge.

S&F in repair vitreous china wash basin white, flat back of size 550 x 400 mm white including waste fittings, brass, chromium plated, coupling, waste pipe, brackets including cutting for and pinning in ends of brackets errect stand, fixing waste pipe complete all as specified & directed by Engr-in-charge.

S&F in repair Brass CP mixer of 15mm dia bore for mixing hot & cold water screwed down for iron pipe and fixed, complete all as specified & directed by Engr-in-charge.

S& F in repairs, White vitreous china laboratory sink of size 600x450x200mm laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, complete all as specified & directed by Engr-in-charge.

S&F Brass CP Florentine Pillar Cock with Extended Lever Handle elbow operated screwed down for iron pipe and fixed, complete all as specified & directed by Engr-in-charge. Make -Jaquar, code FLR-CHR-5031N or equivalent as approved by GE.

S&F Angle cock 15 mm dia cast copper aloy with crutch handle CP concealed type long shank fixed in repairs

Taking up or down steel tubing 15 mm dia with all fitting fixed to wall and ceiling,concelled in walls/ floor etc. all as specified and as directed by Engr-in-charge.

Taking up or down steel tubing 20 mm dia with all fitting fixed to wall concelled in walls/ floor and ceiling etc. all as specified and as directed by Engr-in-charge.

S&F 15mm dia medium grade GI tubing with all fittings and fixtures complete fixed to walls, ceilings etc all as specified and as directed by Engr-in-charge.

S&F 20mm dia medium grade GI tubing with all fittings and fixtures complete fixed to walls, ceilings etc all as specified and as directed by Engr-in-charge.

S&F PVC connection pipe 15mm dia, 450mm long with PTMT check nuts and washer on both ends complete all as directed by Engr-in-Charge.

Demolition and breaking of 150mm dia up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar

M & L for 150mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars

M & L Cement concrete type D2 (1:4:8) using 40mm graded aggregate as in foundations, filling and mass concrete

M&L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested complete for 150mm bore pipe all as specified & directed by Engineer-in-charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth in hard/dense soil and getting out, all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

S&F Pre-painted galvanume aluminium zine coating GI based corrugated steel sheeting 0.50 mm thick any colour having tensile strenght 550Mpa in roof coverings fixed with self tapping screws

M & L Cement concrete type C1 (1:3:6) using 20mm graded aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

S&F in repairs vitreous china white wash down water closet pan, pedestal pattern including fixing bolts, plastic water closet seat and cover with recessed bottom with MS CP hinging device (excluding flushing cistern and flush pipe) complete all as directed by Engr-in-Charge.

S&F in repairs 10 ltrs capacity PVC low level flushing cistern with inlet, ball valve, float, handle including fitting and fixtures and providing connections to WC and flush pipe without any damage to the existing fittings complete all as all as directed by Engr-in-Charge.

S&F Health Faucet ABS body with Wall Hook and 1-Meter Stainless steel braided Rubber Hose

S&F vitreous china bowl urinal flat back size of 465x355x265mm white (minimum) with grating and union for discharge pipe incl providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and incl 60mm long brass screws and pointing around urinal back in cement with grating and PVC 32mm dia waste pipe fixed in repairs, complete all as specified.

S&F in tubular towel rail brass chromium plated 20mm dia, D type 60cm long brass screws, complete all as directed by Engr-in-charge.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches.

S & F 75 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches.

S&F Stainless steel railing 18 gauge of height 0.90m and grade SS T-304 including all accessroies with vertical posts and horizontal rods and fitting to verandah, balconies etc as per manufacturer instructions, all as specified and directed.

M & L 100mm thick PCC type C2, 1:3:6 using 40mm graded aggregate, finishing cement concrete surface even and smooth without using extra cement, all as specified and directed by Engr-in-Charge.

S & F 75mm PVC (SWR) vent cowl

M & L 100mm Cast iron floor trap with CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed by Engr-in-Charge.

Taking down existing unserviceable point wiring of any description/type/ size of light/fan/tube/power/two way/bell etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces to match with the existing finishes all as specified.

Taking down the existing unservicable sub main wiring of any type / description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

M & L for Point wiring using colour coding as per IS with 1.5 Sq mm multistranded copper conductor single core FRLS PVC insulated unsheathed 1100 Volts, ISI-694 marked drawn through ISI marked PVC concealed conduit alongwith its accessories of suitable size, with GI modular sunken boxes of 1.2 mm thick, 60 mm depth of suitable size/module including fixing/ grouting sunken as per site requirement and making good to match with existing finishes including provision of cover with modular frame plate of suitable size for fixing modular switches/ sockets/ regulators etc including running up of 1.5 Sq mm copper conductor FRLS, PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly all as specified for the following :

a) One light point controlled by one switch

b) One fan point controlled by one switch

c) One 2/3 pin socket outlet 5Amps on independent board.

d) One 2/3 pin socket outlet 5Amps on same board.

All as per item No 88.00 above but with copper conductor cable 4 sqmm for 3 pin socket outlet, 15 Amps including provision of 4sq mm PVC insulated copper conductor cable as earth continuity conductor on independent board.

S&F modular switch one way 6A, 1 module

S&F modular socket 6A-2/3 pin combined 2 module

S&F modular switch socket combined 6A/16A , 6 pin, 3 module

S&F Ceiling rose, three terminals PVC/polycorbonate, isolated body

S&F vertical DBs TPN 4 way 415 V double door suitable for TP/FP MCCB as incomer with MCCB 160A , and with provision of SP/TP MCB's as outgoing.

S & F for MCB DB SPN 12 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB DB SPN 8 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

M&L for MCB SPN 63A, 240V, 10KA rating capacity 'C' curve

M&L for MCB SP 40A, 240V, 10KA rating capacity 'C' curve

M & L for submain wiring with approved colour code/as per IS (Red,black & green for three phase) circuit with four single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 25.00 Sqmm (FRLS) in suitable concealed conduit size including two run of PVC insulated multistranded copper conductor nominal cross sectinal area of 16.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engr-In-Charge.(Note :- Four runsof 25.00 Sqmm cable & two run of 16.00 Sqmm cable shall be paid as one unit length)

M & L for submain wiring with approved colour code/as per IS (Red,black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 4.00 Sqmm (FRLS) in concealed conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 4.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engr-In-Charge.(Note :- Two runsof 4.00 Sqmm cable & one run of 4.00 Sqmm cable shall be paid as one unit length)

M & L for submain wiring with approved colour code/as per IS (Red,black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 10.00 Sqmm (FRLS) in concealed conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 10.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engr-In-Charge.(Note :- Two runsof 10.00 Sqmm cable & one run of 10.00 Sqmm cable shall be paid as one unit length)

S&F in replacement of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP 20 Amps, 240 volts

Supply and fixing of recessed mounted down lighter with extruded aluminium frame with high bright LED,idealy suited for low ceiling areas Brilliance 36watt LED 6K,ceiling cutout 2ft x 2ft all as directed.Make- Philips, Orient, crompton or equivalent.

Supply & fix Surface and wall mounted LED tube light along with fixture, 4 ft, 22 W, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver with IP 20 protection, operating voltage 240 V, 50 Hz, AC supply and operating temperature 0 to 50 C , power factor > 0.9, lumen output > 2000 and provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white colour flexible pipe completion all as specified and directed. Make- Philips, Havells, crompton or equivalent.

Supply & fix Surface and wall mounted LED tube light along with fixture, 2 ft,10W, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver with IP 20 protection, operating voltage 240 V, 50 Hz, AC supply and operating temperature 0 to 50 C , power factor > 0.9, lumen output > 2000 and provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white colour flexible pipe complete all as specified and directed. Make- Philips, Havells, crompton or equivalent.

Supply and fixing of building security light fitting LED 30 watt IP 65 with fixing arrangement such as GI pipe bracket,MS clamp,Nut bolts etc and provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white colour flexible pipeconnecting as specified and directed.

Supply & fix wall fans 230 volts single phase oscillating 450 mm sweep suitable for wall mounting.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver, 900 RPM and provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white colour flexible pipe complete all as specified and directed.

Cutting of wall with mason for making window suitable for fixing of 300 mm Exhaust fan and making good as per existing surface of wall complete all as specified and directed.

M & L bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate, charcoal & salt up to ground levl connected to galvanized iron strip 25x4mm as earthing lead up to 7.5 mtr by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 40mm dia light grade pipe for earth lead protection including all necessary earth work, excavation, earth chamber with PCC 1:3:6, Type C1 and RCC chamber cover of PCC 1:2:4 with handle and 20 mm dia GI watering pipe with funnel and wire mesh etc and testing on complete all as specified and directed.

M&L for Earth continuity strip or main earthing strip fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to DBs or any other indicated situation for loop earthing with galavanised iron strip of 25X4 mm size including taking down old u/s strip complete all as specified and directed.

M & L Earthing Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos 8mm dia 25mm long hex. head screw.

Supply and fix geysers of 50 ltr capacity BEE 5 star made of rust proof body to withstand pressure capacity puf insulation and inner container coated with unique polymer protective coating technology to resist corrosion from hard water, including surface and vetical type thermostat and cutout and outsmart three level safety against high temperature and pressur provided with high tech adjustable thermostat and international standards multifunction valves complete all as specified and directed.

BHAGWATI CONSTRUCTION