Development and rejuvenation of Pond and park near HSVP Market, Vill Jharsa, Ward 28. MCG

Amount

NS Item

-M. S. Dustbin – 60 liter capacity made of MS Sheet of 16 mm gauge thick of approx.size 48”H with having 1no inlet and outlet with suitable enamel Paints, set having minimum weight of 30 kgs. Complete item with GST, Transportation, Installation with C.C & amp; labor at site.

-Merry-Go-Round (4 seater): 5' Dia. Main frame is of G.I sq. pipe 2" x 2" x 14 G and having suitable handle & foot-rest is of G.I round pipe 3/4" x 12 Gauge. Central pipe is of G.I pipe 3" x 12 G which further supports with G.I pipe 1” x 12Gauge with heavy duty shaft 50 mm thick & ball bearing assembly. It consists of 4 no Chair made of Molded FRP Plastic in 3mm thick with suitable PU Primer & PU Paints. Complete item with GST, Transportation, Installation with C.C & labor at site including 2 years defect liability period free of cost.

-Bridge Ladder: 10’L x 2’W x 6’H. Horizontal ladder is of G.I pipe jindal make 2”, ¾” & vertical ladder is of same material of 12 gauge ISI mark with suitable PU Primer & PU Paints. Complete item with GST, Transportation, Installation with C.C & labor at site with 2 years defect liability period free of cost to full satisfaction of engineer in charge.

-Chain Swing (2 seater): 10’L x 5’.5W x 8’.5 H. Horizontal frame & vertical legs is of G.I pipe of jindal make 2” x 12 gauge. It stays with G.I pipe 1” x 12 gauge. Swinging seats-2 nos is of FRP molded Seat of 2mm thick fitted with m.s pipe ½” frame x 12 gauge which hang with G.I chain 6mm thick duly plated with ball bearing & m.s flat 6mm thick housing with suitable PU Primer & PU Paints. The rates are inclusive of all taxes with 2 years defect liability period free of cost to full satisfaction of engineer in charge.

- "Twister:- Providing, and fixing Twister of size 1700 X 1300 X 1300 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and ishapod welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Officer -in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of. equipment etc." The rates are inclusive of all taxes like GST, Transportation, Installation in CC to full satisfaction of engineer in charge complete in all respect.

-Wave Slide: 9’.5 L x 5’H. Wave slide is of molded Fiberglass Reinforced Plastic (FRP) of 6mm thick and climbing ladder is of m.s pipe 1” x 12 gauge & m.s rectangular pipe 65 x 25 mm box X 16 gauge as climbing steps which support with 1”.25 sq. pipe x 14 Guage with suitable PU Primer & PU Paints. Complete item with GST, Transportation, Installation with C.C & labor at site.

-Horse Rider Station:- Providing, and fixing of horse rider station of size 1000 x 600 x 1100 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Alczo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer

-"Double Cross Walker/ Cross trainer double:- Providing, and fixing Double Cross Walker of size 1600 X 600 X 1600 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the G.I pipes are 40 mm dia and 2.5 mm thick all G.I pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of G.I pipes are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company like SKF to be approved by Officer -in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of G.I pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength N425 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc." The rates are inclusive of all taxes like GST, Transportation, Installation in CC with 2 years defect liability period free of cost to full satisfaction of engineer in charge complete in all respect.

-Providing and fixing mono block motor 1HP and make Texmo complete in all respect

-Supply of RH Pipe 1" dia.

-Providing an fixing of Gate valve for Hydrant connection.

-(i) 6 No. Ornamental Design FRP pillar FRP base pedestal with vertical fitted design having base width of size 260mm x 260mm and height 900mm having 4 no. of size 15mm drilled in the base with hold fasts and having B class vertical m.s pipe of size 89 mm and height 2890mm, the central m.s pipe having FRP capital suitably mounted at appropriate height complete as per design enclosed. Complete pillar suitably grinded spray primered and subsequently spray painted with two coats of enamel paints is required shade. (ii) 12 No. spndred and 6 no. Friezes Floral and Ornate decorative design combination of spandrel and frieze, matched to be suspended between two m.s pillars as per the design copy enclosed. The spandrel (L-Bracker) having length 310mm and height 300mm the frieze (Top Panel) height 220mm and length as per the size of the gazebo. The frieze mounted on m.s tabular pipe frame of size 40mm x 25mm, frieze properly welded to the column pollars at either ends. Complete set of spandrel & frieze uniformly grinded spray primered, spray painted with two coats of enamel paint. (iii) 3 No. cast iron base panel railing with frame Floral and Ornate decorative design cast iron side railing panel as per design copy enclosed having height of 730mm and length as per size of Gazebo. Each panel top and bottom mounted with mild steel tubular pipe frame of size 40 x 25 mm. the bottom mild steel pipe having 3 nos. of hold fasts in m.s pipe of size 40 x 40mm and length 50mm welded at the base to hold the panel in the ground. The complete railing panel grinded for neat surface finishes spray primered and subsequently spray painted with two coats of enamel paint in required shade. (iv) One set of top frame with frp roof Top frame in m.s tubular pipe of size 40 x 40mm properly welded and grinded. The top frame mounted with FRP molded Sheet of 2 mm thick bent to profile on either ends with clear width installation of frp sheets fixed horizontally along the length between column pillars. Each sheet enamel painted in red color on both sides. Each such sheet properly riveted to horizontal sheets. The roof pipe frames properly primered and painted in red color. The complete item is without C.C floor & without sitting bench. rates are including with all taxes.

-Chainlink fencing with 50x50x2.6 mm wire with zinc coating on wire 2.7Kg/m2 Span of two angles in 1.8 mtr so cost of 1.8mtr is Concerting coil Having core wire High Tenclle spring steel wire 2.6mm Dia as per Zinc Coating on wire 150Gms m2 Min strip for Blade 0.5mm+005 mm with RBT mounted on angles with Installation 0.75 diax1.0 Rmtr=1.65 Kg.RBT wire with 03 nos. of strings Required not bolts and U nails=09 nos in each post of m.s. Angle M.S angle 2.50x50x50x6mm=2.5 mtr each 2.50Rmtrx4.50 Kg./Rmtr=11.25Kg.xRs.m.s. angle for concertina coil holder 30x30x6mm [email protected]/Rmtr=4.28Kg. 1.80 Rmr x20x5mm flat m.s. bar 1.80 Rmtrx0.80Kg/Rmtr=1.44 For installation of each angle with Coment concrete casting 1:1.5:3 in foundation with 0.30x0.30x0.30cm complete with Excavation of foundation pit, fixing post. Distance between each angle post shall be 3.00 Rmtrs. Cost would come for each RD=Rs. 1368.14/3 Rmtr To cover unforeseen risk, carrying of material from site to site Arranging water, generator and drilling to rock for embedding 02 nos. of 12mm steel bar with Araldite to welding the angle required on rock bed (Analysis

-Arm and Shoulder Wheel:- Providing, and fixing Arm and Shoulder Wheel of size 130 X '1200 X 1350 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the G.I pipes are 40mm dia and 2.5 mm thick all G.I pipes made up of hot roiled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel c equivalent of 80-120 micron thick. All welding joints of G.I pipes are robotic welded with joints scalloped as necessary an dressed off removing sharp edges and burrs. Zinc prime paint to be applied at all welding points prior to finish ink Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and resistant environmental friendly. Bearing used shall be maintenance free , duly oiled sealed and self lubricated made by reputed company like SKF to be approved by Officer -in-Charge Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of G.I pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M2: nd J shaped welded bolts and once the concrete is set, ft ;he equipment on to it and cover nuts and bolts with the base Mate cover, all complete as per direction and approval of -2,engineer-in-Charge regarding material, shape of equipment colour on metal, seat and base cover plate and fixing of equipment etc. The rates are inclusive of all taxes like GST, Transportation, Installation in CC with 2 years defect liability period free of cost to full satisfaction of engineer in charge complete in all respect.

-Supply of Pre cast concrete RCC Benches hand rest of size 1500mm manufactured By M-30 grade of Concrete. Concrete planks in Red colour size 1500mm x 425mm x 50mm each bench consist of 2 no L Shape base for in grey cement colour thickness 80mm back height 890 mm front height 450mm siting length of bench 1500mm sitting height 450mm total height 890mm.

-Providing ,laying, jointing, fixing and testing of GI pipe line (medium) cost of special viz, tees bends sockets, elbow , GI Hooks etc. painting with anti corrosive paint complete in all respect of 20 mm GI pipe (RS. 208/- per mtr)

- Sea -Saw (4 seater): 8’ L x 5’.5 W x 15” high. Frame is of m.s pipe 2” x 12gauge. Sitting planks is of m.s pipe 2” x 12 gauge and its cantilever & handles is of m.s pipe ¾” x 12 Guage .Sitting seats -4nos is of molded FRP material in 3mm thick with suitable PU Primer & PU Paints. Complete item with GST, Transportation, Installation with C.C & labor at site.

-Providing and fixing 3/4"dia Hydrant connection

-Knee HIP Raise:- Providing, and fixing Knee Hip Raise of size 1105 X 550 X 11480 mm make of Green Gym or Equivalent fabricated with main post of 140 rum din and 3.0 mm thick rest or the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Mao Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped

Bidder Name

Amount

Surender Kumar Contractor(GSTN-NA)

Big Brother Traders(GSTN-NA)

Big Brother Traders

Big Brother Traders