PROVN OF TOILET AND SHED AT STN AUDITORIUM BLDG NO P-181 PROVN OF 200 X 1.5 MTRS INTERLOCKING TILES PATHWAY FROM CH-1 TO B COY CIH TO CH3 AND CH3 TO TOILET BLOCK AT COOK HOUSE AREA AND PROVN OF 30 X SECURITY LIGHTS 10 AREA 5 B COY LOC AT OLD ILP LOC

Amount

Surface exavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil all as specified and directed

Material & labour for hardcore of broken stone or boulders of gauge n.exc. 63mm, deposited,spread and leveled in layers n.exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100 mm thich PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed

M&L Cement concrete 1:2:4 type B0 using 12.5mm graded agg 25 mm thick for laying of floor etc complete all as specified and directed

M&L for joint free non skid coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc over & including 15mm thick screed bed in CM 1:4, set & jointed in neat cement slurry and pointed with white or coloured cement to match complete

M&L coloured ceramic glazed tiles 450x300x7mm thick as in dado/skirting etc including 10 mm thick rendering in CM 1:3, set & jointed in neat cement slurry & pointed in white or coloured cement slurry & pointed in white or coloured cement.

Material & labour for brick work with sub class ‘B’ bricks, straight or curved on plan, exc. 6 metre mean radius built in CM(1:4) as in half brick wall complete all as specified and directed.

Use & waste of form work to edges of concrete flats, n.exc. 20 cm wide, horizontal or sloping and similar works, complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc 200mm thick (horizontal or slopping).

Material & labour for RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in beams, lintel, lintel band etc complete all as specified and directed.

M&L RCC Type A1 1:1/2:3 (20mm graded aggregate) nominal mix over slabs supported on walls, beams and columns in floor, roofs, landing, balconies canopies, deck slabs and in shelves and the like

Supply & fix mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Supply & fix mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending as in stirups complete all as specified and directed.

Supply & fix mild steel work as in hold fast etc and similar articles confirming Fe-290 Gde E-165 complete all as specified & directed.

S & F factory made single extruded WPC (Wood polymer composite) solid door/window/ceosetory windows & other frames/chowkhats of size 50 x 100 mm comprising of virgin PVC ploymer of K value 58-60 (suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strenght of 2200 N (Face) & 1100N (Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixede in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerence in dimension i.e. depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F factory made solid PVC Moulded door shutter(with particle board core), 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on front face and 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing .

Supply & fix factory made steel ventilators fixed type with glazing bars complete all as specified and directed .

Supply & fix 3mm thick sheet glass, frosted type ordinary quality glazing with oil putty or fixed with wooden beads or in steel windows in square n.exc. 0.50sqm each pane

Supply & fix mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted forged into spikes, framed guard bars, railings and similar work complete conforming to Fe-410-0 or Fe-310-0.

M&L PCC 1:3:6 type C1 using 20 mm grade stone aggregate as in hold fast etc

Supply & fix mild steel butt hinges 100mm size medium weight, cold rolled complete all as specified and directed.

Supply & fix 125mm size aluminium alloy handles cast type anodized complete all as specified and directed.

Supply & fix 150mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed.

Supply & fix 250 mm long Aluminium alloy, Sliding door bolts, with hasp, staple and fixing clips of sheet, cast or extruded section and fixing bolts of extruded section or cast aluminium alloy complete all as specified & directed.

M&L preparation of new or previously untreated steel surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material & labour for 15 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15 mm thick in CM 1:4 on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

Preparation of newly plaster surface of wall and applying two coats of cement base paint over one coat of cement primer complete all as specified.

Materials & labour for prepration of newely plastered surfaces of wall and applying two coat of Oil Bound distemper on walls, white or tinned over a coat of chalk whiting complete all as specified & directed.

S&F Vitreous china wash down water closet pan ( pedestal pattern), white (excluding fixing bolt, flushing cistern and flush pipe) but including P or S trap, sheet cover of white colour all as directed and specified.

Supplied and fixed vitreous china WHB white flat back size 550x400mm including Supplied and fixed angle iron brackets, CP waste coupling, complete all as specified & directed.

Supply & fix in PVC low level flushing cistern of 9-10 ltrs capacity, ISI Marked, white, symphonic action type with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm bore, suitable for low level cistern complete all as specified & directed.

Supply & fix in vitreous china urinal half stall type with including providing & fixing of plugs bedding against wall in cement mortar 1:2 pointing around urinal back in cement mortar complete all as specified.

Supply, fix 15mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

Supply, fix 20mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

S&F 15 mm dia Gun -metal,globe or gate valves,with iron wheel head ,screwed both ends for iron pipe and fixed.

S&F 20 mm dia Gun -metal,globe or gate valves,with iron wheel head ,screwed both ends for iron pipe and fixed.

Supply & fix bib taps cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe of 15mm bore, complete all as specified & directed.

Supply & fix stop cock fancy type chromium plated with long shank and cup concealed type for 15mm bore steel pipe complete all as specified and directed.

Supply and fixed angular stop valve (concealed type) , 15mm dia, cast copper alloy,CP fancy type with long shank and cup screwd down, high pressure ,screwed both ends for iron pipes or for unions and fixed in pipe all as specified and directed.

Supply & fix pillar taps, fancy type cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore, complete all as specified & directed.

Supply & fixing chromium plated shower roses with swivel joints of 125mm size complete all as specified & directed.

S&F Soap dish, vitreous china white, approximate size 160x160x90mm.

S&F aluminium Hat pegs, solid body, 125mm to 175mm.

S&F grating doom 100mm dia of PTMT (Minimum weight 25gms).

Supply and fixing PVC waste pipes of 40/32mm bore suitable for wash hand basins/sinks complete all as specified & directed.

Supply & fix in PVC connections of 450mm long of PRYAG Make suitable for 15mm dia iron pipe including PTMT nuts complete all as specified & directed.

Supply & fixing MS tubular towel rail, 60 cm long, 20mm bore, chromium plated complete all as specified & directed.

Supply and fix sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromiun plated bracket guard and railing 60 cm long

Supply & fix rotational moulded polyethylene water storage tanks 500 liters capacity, (cylindrical, vertical in closed top) hoisted and fixed in position with all fittings complete all as specified & directed.

Supply & fix PVC ball valves, high pressure with polyethylene float and fly nut complete screwed for iron pipe 20mm bore complete all as specified & directed.

Supply & fix 110 mm bore PVC (SWR) pipe in any length fixed to walls with clamps and laid in floors etc. complete all as specified and directed.

Supply & fix PVC bends any radius suitable for 110 mm thick PVC pipes complete all as specified and directed.

Supply & fix 75 mm bore PVC (SWR) pipe in any length fixed to walls with clamps and laid in floors etc. complete all as specified and directed.

M&L PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement.

Supply and fix PVC bends 75mm bore, any radius complete all as specified & directed.

S&F 110 mm PVC(SWR) vent cowl

Material & labour for 100mm dia cast iron Nahani traps with grating including jointing with waste pipe fixed in cement concrete type B1 (1:2:4).

Material & labour for 75mm bore PVC floor traps plain with grating including jointing with solvent cement complete all as specified & directed.

Excavation in trenches not exc. 1.5 metre wide and not exc. 1.50 metre in depth for foundation, laying of cables fixing of poles and for manholes etc n.exc. 10 Sqm on plan and n.exc. 1.5 metre depth and getting out in soft/loose soil complete all as specified and directed.

Removing excavated materials (soils) to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.50 above the starting point complete all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick as in soft/loose soil complete all as specified and directed.

Material & labour for cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete and sub base of floor complete all as specified and directed.

Material & labour for brick work with sub class ‘B’ old sized bricks, straight or curved on plan, exc. 6 metre mean radius built in CM(1:6) complete all as specified and directed.

M & L PCC 1:3:6 type C2 as Concrete bed to drain pipes including packing under, and hunching against the sides of pipes after they are laid and tested; in

Supply & fix 150mm dia salt glazed stone ware (SGSW) drain pipes laid in trenches and jointed in CM 1:1 including testing complete all as specified and directed.

Material & labour for pre-cast RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in cover slabs, set in CM 1:6 including necessary form work and finishing to exposed surfaces complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2(40mm graded aggregate) as in plinth protection, path etc finished the surface even & fair complete all as specified

P.C.C 1:3:6 Type C-1 as in bed blocks, benching, copings and like complete all as spfd and ditected

S&F MS framed work of any section FE 410-w (Gde- E-250) quality as directed by Engr-in-charge as in truss/ purlins etc incl cleats, brackets complete al as spfd and directed

Material & labour for preparation of new or previously untreated steel surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M & L Sand filling under floors including watering and consolidation

M&L Machine pressed precast concrete coloured Inter locking paver block of any shape and size conforming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment over sand cushion & laid over sub base all as specified and directed. Note : Sand cushioning measured and paid separately

Material & labour for chequered cement concrete tiles 20cmx20cmx20-25mm thick set, jointed and pointed in neat cement slurry in floor over and including 15mm thick screed bed in CM (1:6) complete all as specified & directed.

Material & labour brick work with subclass 'B' bricks in CM 1;6 brick straight or curved on plain exeeding 6m mean radius complete all as specified.

M&L for 75 mm thich PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed

M&L PCC 1:3:6 type C1 using 20 mm grade stone aggregate as in benching, coping, kerbs etc

M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in and including Concealed PVC conduit of size 20/25mm ISI marked inclusive of tees ,bend ,elbows etc upto and including sunk in anodized pressed steel box for housing switch socket etc with white laminated 3 mm thick hylam sheet cover ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for following :-

One light point controlled by one, one way switch 5 Amps

One fan point controlled by one, one way switch 5 Amps and regulator

One 3 pin 5 Amps switch socket outlet point controlled by one switch on the same board.

S & F for Switch Piano type single pole 5 amp, 230 Volts complete all as specified and directed at site.

S & F for socket outlet 2 in 1 , 5 pin, 5 amp, 230 Volts complete all as specified and directed at site.

Supply and fixing ceiling rose surface bakelite 3 terminals 65 x 50mm complete all as specified.

M & L for Sub main wiring with approved colour coding as per IS with four single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc two runs of PVC insulated with 6 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Four runs of 6 sqmm cable, two runs of 6 sqmm cable and one run of PVC conduit will be measured as one unit

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 6 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for energy efficient exhaust fan of 230 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan and making good finish after fixingis deemed to be included in overall rate quoted).

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 2 core, complete all as specified and as directed.

S & F GI tubing medium grade of size 40 mm dia fixed on walls / laid in trenches as protection pipe for under ground cable including provisioning of specials and clamps etc complete all as specified and as directed.

M & L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level, connecting to GI earth wire 4mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron or steel including 15 mm dia. medium grade protection pipe for earth lead complete with charcoal and common salt including watering arrangement with galvanized iron pipe light grade 20 mm dia, PCC Chamber, CI frame and cover, MS funnel with wire mesh all as shown in electrical plate no 3 of SSR part I including excavation and earthwork in any type of soil/strata and testing on completion. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

S & F for Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 2 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed.

S & F for wall mounted LED tube light fitting 10 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 2 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

Supplying, transporting, errecting and fixing steel tubular swaged welded pole of over all height 9.00 m long complete type 410-SP-31 conforming to IS-2713 (Part I to III 1998 with cast iron base plate, finial tapper plug cap, bolt, nut and washer etc. incl painted with 2 coats of aluminium paints over a coat of red oxide primer, complete all as specified and directed by Engr-in-charge. Note : Excavation, earth work and PCC work for embedding pole shall be measured and paid seperately.

S&F XLPE insulated heavy duty electric cable of size 10 Sq mm 4 core with aluminium multi stranded conductor 1100 volts grade served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall sheaths laying in trenches/cable ducts, fixed to wall/pole complete all as specified

S&F XLPE insulated heavy duty electric cable of size 6 Sq mm 4 core with aluminium multi stranded conductor 1100 volts grade served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall sheaths laying in trenches/cable ducts, fixed to wall/pole complete all as specified

Spreading ribbed soil in trenches as in cable cushioning all as per IS 1255-1983 and as directed. Note :- Excavated approved soil shall be ribbed by using sieve to separate composite particles etc as per IS and refiiling in trenches before laying of cable 8 CM and 15 CM after laying of cable. This is than gently punned down to a depth of 10 cm above the top of upper most cable (ii) For the purpose of measurement only punned thickness only will be considered for paymet.

Supply and laying of bricks of size 230 x110 x 75mm covering with width equal to lenght5 of bricks as mechanical protection cable with sub class ‘B’ laid dry flat in trenches complete all as specified and directed.

Material and labour for plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate for foundations / filling around the post, Poles etc all as specified and as directed.

Material and labour for plain cement concrete 1:3:6 type C1 using 20 mm graded stone aggregate for path ways, hard standing & pole coping make smooth including necessary form work and applying two coats of white wash on exposed surfaces etc complete.

Material and labour for cutting of bituminious road/ hard standing/PCC path/wall up to a size not exceeding 20cm width and not exceeding 60cm in depth for laying of protection pipe for cable including making good the disturbed road/hard standing by providing PCC (1:2:4) type B1, 40 mm graded crushed stone aggregate upto existing surface level or removing any type of tiles carefully and refixing properly as per existing surface complete all as specified and as directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete includinng street light fitting bracket made out of 40 mm bore GI pipe, light grade, tubing bend to shape, 1.2 metre long, fixed to pole/wall with and including two sets of clamps made out of flat iron of size 40 x 6 mm with bolts, nuts and washers and clamps made out of 40x6 mm bending to shape, drilling holes for bolts suitable for fixing GI pipe bracket to steel pole, made in two halves, including nuts, bolts, washers and painting with two coats of aluminium paint over a coat of red oxide primer complete.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete includinng street light fitting bracket made out of 40 mm bore GI pipe, light grade, tubing bend to shape, 1.2 metre long, fixed to pole/wall with and including two sets of clamps made out of flat iron of size 40 x 6 mm with bolts, nuts and washers and clamps made out of 40x6 mm bending to shape, drilling holes for bolts suitable for fixing GI pipe bracket to steel pole, made in two halves, including nuts, bolts, washers and painting with two coats of aluminium paint over a coat of red oxide primer complete.

Supply and fixing LED flood light 70 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp.protection complete includinng street light fitting bracket made out of 40 mm bore GI pipe, light grade, tubing bend to shape, 1.2 metre long, fixed to pole/wall with and including two sets of clamps made out of flat iron of size 40 x 6 mm with bolts, nuts and washers and clamps made out of 40x6 mm bending to shape, drilling holes for bolts suitable for fixing GI pipe bracket to steel pole, made in two halves, including nuts, bolts, washers and painting with two coats of aluminium paint over a coat of red oxide primer complete.complete, all as specified and directed.

Supplying & fixing of terminal panel box of size 155 mm x 210mm x 92mm of outdoor pole mounted front operated cubical type Box as per IEC 60439-1 (IS:8623) & IEC 60439 -2 dead back, free standing, dust and vermin proof, switchboard with IP 66 protection with suitable for use 440 volts, 3 phase 4 wire 50 Hz system. The Board/Panel shall be made out of moduler POLYCARBONATE THERMOPLASTIC ENCLOSURES. The gasket material shall be Polyurethane; while the gasket shall be internally embedded. . The manufacturer of board/panel shall submit a copy of test report in accordance with IEC 60529. The Panel Should be assembled at manufactures factory (Make for terminal panel Box - Hensel/hager of Equivalent to other manufacture POLYCARBONATE THERMOPLASTIC ENCLOSURES.and Panel box having 1x 6 Amp MCB (Make -Indo Asian(optipro /Havells/Legrand), 16 Sq.mm Terminal Block (04 Nos) , 6 Sq.mm Disconnected Terminal (01 No) ,4 Sq.mm Earth Terminal (01 No) including MS clamp flat 20 mm x3 mm in suitable fixed to pole with nut bolts Complete.

M& L for Rigid non-metallic PVC conduit exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. to be fixed on pole with all fittings including mouth pieces complete all as directed.

M&L in repairs Cable PVC insulated PVC unsheathed un-armoured copper conductor (multi stranded) of cross sectional area 1.5 sq mm 3 core drawing in PVC conduit/Steel tubular pole all as required for connections to light fittings complete all as directed.

Supply and fix MS sheet metal enclosure street light timer switch distribution board double door type , including provision of opening for cable entry duly painted with two coats of synthetic enamel paint over one coat of red oxide and suitable fixing MS clamps 40x5mm thick bend to shape drilled with holes suitable for fixing to PCC / Steel tubular pole all as directed and specified and consisting of the following including taking down old enclosure.:- (a) Aluminium bus bar chambers 4 strip 300 mm long 100 Amps (b) MCB SPN 40A 10KA "C" 03 Nos (c) Digital Time switch 3P Module,weekly programm with battery bach up 100 hrs Current of capacity 16 Amps with change over - 01 Nos Make - L&T/Indo asian/ ABB

Earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of plate not less than 1.5 m below ground level connected to and including galvanised iron strip 25×4mm (up or 7.5 mtr length) and GI pipe 40 mm light grade for protection of GI earth strip by means of bolts, nuts, checknuts and washers made out of galvanised iron and connected to earth test point as shown in electrical plate No. 3 of SSR Part-1-2009 and as specified or indicated and testing on completion including excavation and earth work any in type of strata available at site, PCC (1:3:6) type C-1 for earth chamber, precast RCC slab 50mm thick in cement concrete (1:2:4) type B-1 reinforced with welded steel wire fabric (xpm) weight not less the (4kg/sqm) funnel with GI watering pipe of 20mm bore medium grade, wire nuts and lugs complete all as speified.

M/S RANJAN AND DAUGHTERS GROUP (BID ID -3110482)

MS AMRENDRA KUMAR SINHA (BID ID -3111823)