SPL REPAIRS TO BLDG NO T-145/1 T-146/1 AND T-146/2 AT NCO LINE SPL REPAIR TO SEWAGE LINE SEPTIC TANK AND SOAKAGE WELL AT BURKI LINES AT MORABADI POCKET AND PROVN OF LADIES TOILET AND BATHROOM FOR GE RANCHI COMPLEX AT RANCHI MIL STN

Amount

Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges as in roof covering.

S&F prepainted galvalume aluminium zink coating GI based corrugated/ semi - corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering fixed with coach screw as per manufacturers instrution complete.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering as ridge/cladding to wall, fixed with self tapping screws as specified

Dismantling timber scantling 40 sqcm and over in section in any position in framed work complete.

S&F for Roof trusses (framed), trusses, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) incl distance pieces, cleats etc complete Fe 410-W(Gde E-250) quality-A.

Dismantling of wall and ceiling board any thickness/description including cover fillet.

S&F for Anodised Aluminium snap grid size 605x604mm frame work for false ceiling all as specified and directed by Engr-in- charge.

M&L 4mm thick non asbestos fibre cement designer building board of size 600X600 fixed or laid/inserted to timber/GI/Aluminium framework fixed in ceiling flat or sloping.

Demolition of cement concrete (un-reinforced) in ground floors and paving n.exc 15cm thick (below or above ground level).

M&L for 75mm thick PCC type C2 1:3:6 (using 40mm graded stone agg) as in plinth protection/Path/floor finishing surface of concrete topping even and fair without using extra cement complete.

M&L providing cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in copings/kerbs and the like including weathering, slightly rounded for chamfered angles and throating, as directing complete.

M&L for 75mm thick PCC type D2, 1:4:8 (using 40mm graded stone agg) as in sub base floor surface complete.

M&L for Chequered cement concrete tiles (300x300x25)mm thick, set, jointed and pointed in neat grey cement slurry in floors

M&L for PCC type C2 1:3:6 (using 40mm graded stone agg) as in surface channels and drains.

M&L for extra forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra, including forms, moulds, mitred/ stopped end etc.

Dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing ) removing serviciable tile to store & rubbish off the permisses.

M&L for roughening surface of old concrete floor by picking, sweeping cleaning and washing down with to remove dust

M&L for brushing neat cement slurry with 3.0 kg of cement per Sq mtr

M&L, 15mm thick screed bed or bedding layer of mortar in CM (1:6) for lying floor finishes and surface fair and even.

M&L Non - skid Ceramic tiles of any colour/shade 7 to 8 mm thick area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles complete.

M&L Non - skid Ceramic tiles of any colour/shade 7 to 8 mm thick area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles complete.

Description all as per items No 21 above, but as in verticle surface or skirting complete.

M&L, 10mm thick rendering as screed bed or bedding layer of mortar in CM (1:4) for lying tiles on vertical surface finishes.

M&L, glazed ceramic coloured tiles of size 350 X 250 X 7mm/ 450 x 350 x 7 mm thick as in walls etc set and jointed in neat cement slurry and pointed in colour cement to match the tiles.

M&L for machine cut kota stone slab 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including circular cutting,chamfering of edges as required.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons

M&L 20mm thick Granite slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including circular cutting,chamfering of edges as required.

Demolition of brick wk masonry built in cement mortar incldg all quoins arches pillars etc

M & L Brick wk with sub class ‘B’ bricks straight or curved on plan exc. 6m means radius in CM 1:6

M&L Brick work with sub class 'B' Brick straight or curved on plain to any radius in half brick thick wall built in cm 1:4

M & L for RCC (1:2:4) type B-1using 20 mm graded stone aggregate as in slab supported on wall ,Chajjas,deck slab Shelves/tank staging etc.

Use & waste frame work to soffits of suspended slab such as floor or roof slab, chajjas and similar work not exc 200 mm thick (Horizontal or slopeing) rough finished complete.

M & L Mild steel bars 10mm dia TMT Bars and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to

Description all as per item 33 above but 6mm to 8mm dia

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area n’exc1.5 Sqm and removing from site.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc1.5 Sqm but n.exc 4.00 Sqm each and removing from site.

M&L for Pressed steel frames 125 x 60 mm size of frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete

M&L for Pressed steel frames 105 x 60 mm size of frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete.

Cutting holes in brickwalls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required not exc. half brick

S&F particle board core factory made solid PVC Moulded door shutter 28 to 30mm thick (stiles) with 2 mm thick Moulded PVC sheet on the front face & 2 mm plain colour PVC sheet on back faces,and with particle Board Core supplying and fixing in frame at site as per specification and drawing.

S&F factory made wire gauzed PVC door shutter 30 mm thick style consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded both side prelam PVC Sheet and stile & rails feathered at edges having a PVC sheets strip of 20 mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail and bottom rail on either side and as gap inside for top rail and bottom rail.panel will be wire gauze in lieu of prelam sheet ,the wire gauze shall be wrapped on an additional square 8mm M.S.Solid tube and this tube shall be welded to M.S Tube.the wire gauge shall be stretched to tighten firmly supplying and fixing in the frame at site as per specification and drawing.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, in opening as per specification and shown on drg.

S&F, factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rails, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement, in the frame at site as per specification and shown on drawing.

S & F 100 mm Butt hinges medium weight medium cold rolled mild steel.

S&F 200 mm long aluminium anodised barrel tower bolt of extruded section complete.

S&F of 100 mm size aluminium handles cast type anodised.

S&F 250mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.

Hacking out old broken glass any thickness, size, quality or description, from metal/wooden frame including punching or drilling out old glazing pins and removal of demolished material from site.

S & F 4mm thick plain sheet glass ordinary quality & glazing with oil putty n.exc 0.50 Sqm in each pane .

Description all as per items No 49 above, but in 4 mm thick figured glass pin headed type complete.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanized wire staples over steel windows and gauzed door.

M/L Steel window with side hung shutter including projecting type hinges with steel handle and steel peg stay, complete with glazing bars, dove tailed or welded (including two nos tower bolts 125mm in each leaf and one nos MS flate iron 25x 3mm handle in each leaf.

M/L Steel window with side hung shutter including projecting type hinges with steel handle and steel peg stay, complete without glazing bars, dove tailed or welded (including two nos tower bolts 125mm in each leaf and one nos MS flat iron 25x 3mm handle in each leaf.

S & F as in repairs Steel ventilator with top hung shutter including hinges steel peg stay, complete.

S&F in repair 20mm dia Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc.

S&F in repairs mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete

S&F in repairs sink with drainage board made of stainless steel 1mm thick kitchen with plug washers and waste coupling and pipe incl cantilever brackets and connecting union to pipe overall size 915x460mm, bowl size 410x330x160 mm.

S&F in repair stainless steel plate rack 1mm thick of size 750X600mm and depth 250 mm , fixed on wall surface as per manufacturer's instruction and making good the surfaces .

Taking up or down 15mm dia steel tubing and connection including cleaning for re-fixing or removal from site.

S & F, 15mm bore galvanized steel water tubing medium grade with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors.

Taking up or down 20mm dia steel tubing and connection including cleaning for re-fixing or removal from site.

S & F, 20mm bore galvanized steel water tubing medium grade with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 in brick walls for concealed water tubing, cutting not exc 10cm girth

Dismantling water tanks Capacity in exc 500 & n exc 1000 litres and removing to store

S&F Rotational moulded polyethlene water storage tanks (cylindrical vergical with closed top) Capacity in 1000 litres hoisted and fixed in position all as specified in SSR Part I

S&F PVC Ball valves, high pressure, with polythene float & steel rod & fly nut complete, screwed for iron pipe or brass ferrule and fixed 20 mm bore pipe.

S&F Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for 20 mm bore pipe.

S&F PVC (SWR) pipes 110 mm single socketed in any length with rubberring joints, laid in trenches or in floors

S&F PVC (SWR) pipes 75 mm single socketed in any length with rubberring joints, laid in trenches or in floors

S&F PVC bends any radius 110 mm dia

S & F in repair vitreous china wash hand basin, white flat back of size 550 mm x 440 mm including brackets or erecting stand and making necessary arrangement for fixing.

S&F in repair vitreous china squating pan 'ORRISA' pattern, size 580X450mm white with integral foot rest complete including connection to trap and to antisyphonage pipe etc complete including making good to floor.

S&F in repair 10 ltr capacity PVC low level flushing cistern, white inlet ball valve, float and handle and connection to pipe including bracket.

S&F 450mm long, 15mm dia, PVC connection pipe, with brass unions on both ends.

S&F in repairs15 mm bore bib taps, chromium plated cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule.

S&F in repair 15 mm bore angle/ stop valves , fancy type chromium plated with long shank and cup (conceaeld type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

S&F 32 mm dia waste/flush pipe for urinal and WHB complete.

Supply only 15 mm pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe.

S&F for Brass chromium plated tubular towel rail 20mm dia D Type, 60 cm long between flanges.

S&F in repair Brass chromium plated shower rose 125mm with or without swivel joints, including fixing to steel pipe or union complete.

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms)complete.

M&L 75mm dia PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete.

Taking down cement plaster of any description on brick or stone walls/concrete surface etc. including racking out joints, hacking for key, scrubbing down with water etc.

M & L, 15mm thick rendering on fair faces of brick work/concrete surface in CM (1:6) surface finished fair & even complete.

M & L, 15mm thick rendering on fair faces of brick work/concrete surface in CM (1:4) with applying water proofing compound (As per manufrature instruction) surface finished fair & even complete.(WPC will be paid saperatelly)

Supply only liquid water proofing compound.

M & L preparation of new plastered surface of wall and applying two coats of oil bound distemper over a coat of 1mm thick wall care putty complete.

M & L preparation of complete removal of existing treatement from old plastered surface of wall and applying two coats of oil bound distemper over a coat of 1mm thick wall care putty complete.

M&L for applying Two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 ltr/10sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10sqm over a coat of plaster of paris putty of 1mm thickness on new plastered wall surfaces.

M&L for applying Two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 ltr/10sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10sqm over a coat of plaster of paris putty of 1mm thickness after complete removal of existing treatment on wall surfaces.

M&L, applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of newly steel surfaces of any description over 10cm width or girth not otherwise described.

Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with Creosote oil complete all as specified and directed.

M&L Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to fe.290.Gde-E-165

S&F Flat iron / angle iron for wind tie, hold fast to fixed door/window as in filled etc.

Demolition and breaking up drain pipes Internal dia of pipe in 100 mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar

Demolition and breaking up drain pipes Internal dia of pipe in150 mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar

M&L PCC (1:3:6) Type C-2 Concrete bed to drain pipe including forming cradles in against the side or pipe after they are laid and tested for 100 mm dia pipe.

M&L for 100mm dia DCW (Double Wall Corrugated) HDPE pipe, class SN4, laid and jointed complete with collars.

M&L PCC (1:3:6) Type C-2 Concrete bed to drain pipe including forming cradles in against the side or pipe after they are laid and tested for 150 mm dia pipe.

M&L for 150mm dia DCW (Double Wall Corrugated) HDPE pipe, class SN4, laid and jointed complete with collars.

Demolition of cement concrete (reinforcement) any description and position not other wise specifically.

Providing precast cement concrete type B1, 1:2:4 (20mm grade aggregate) in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in CM 1:4

M & L Brick wk with sub class ‘B’ bricks straight or curved on plan exc. 6m means radius in CM 1:4

M&L for loose filling with broken bricks aggregates of gauge 80 to 150 mm in soakage pits, soakage wells

M&L for PCC type D2 1:4:8 (using 40mm graded stone agg) as in foundation, filling and mass concrete.

Demolition of cement concrete (un-reinforcement) any description and position not other wise specifically.

M&L for broken stone hardcore of gauge n exc. 63mm, deposited, spread and levelled in layer n exc. 15cm thick, watered and rammed to a true surface complete.

Excavating in trenches, n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc, or for shafts, wells, cesspits, manholes, pier holes, etc n exc 10 sqm on plan and n.exc 1.5m in depth and getting out soft/loose soil.

Returning filling in including spreading levelling, watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Removing excavated materials not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point in soil.

S&F PVC (SWR) vent cowl 110 mm.

M&L applying three coats of white wash including preparation of newly plastered surfaces of wall.

Surface excavation n.exc 30cm deep and average 15cm deep and getting out in soft/loose soil.

Rough excavation not exc 1.5m deep and getting out in any type of soil

Rough excavation exc 1.5m but not exc 3.0m deep and getting out in any type of soil

M & L for RCC (1:2:4) type B-1using 20 mm graded stone aggregate as in beam, cantilevers,bressummers,lintle over 1.5m span etc.

M & L, 10mm thick rendering on fair faces of brick work/concrete surface in CM (1:6) surface finished fair & even complete.

S & F 75mm Butt hinges extrucded aluminium alloy with galvanised mild steel hinge pin anodised and fixed, type C-21.

S&F 100 mm long aluminium anodised barrel tower bolt of extruded section complete.

S&F PVC Ball valves, high pressure, with polythene float & steel rod & fly nut complete, screwed for iron pipe or brass ferrule and fixed 25 mm bore pipe.

S&F Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed for 15 mm bore pipe.

S&F PVC bends any radius 75 mm dia

S&F PVC vent cowl any radius 75 mm dia

M&L for 150mm dia reinforced concrete pipes, class NP2, laid and jointed complete with collars.

S & F vitreous china wash hand basin, white flat back of size 550 mm x 440 mm including brackets or erecting stand and making necessary arrangement for fixing.

S&F 110mm PVC (SWR) WC connector bent type

S&F 10 ltr capacity PVC low level flushing cistern, white inlet ball valve, float and handle and connection to pipe including bracket.

S & F 15 mm bore fancy type bib taps, chromium plated cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule.

S & F Vitreous China half stall urinal flat back, white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)

M&L PVC(SWR) gully trap 125/110mm, setting and jointing with solvent cement complete.

M & L preparation of new surface of wall and applying two coat of cement base paint, in any colour complete.

M & L for Providing precast cement concrete type B0 1:2:4 (using 12.5 mm graded stone aggregates) in louvres and jallies, 35mm thick (measured solid), in cluding all mould- ings but excluding frame and set in CM 1:4 complete all as specified and directed.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for taking credit and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed.

Taking down ceiling fan/ exhaust fan and refixing of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades complete all as specified and as directed.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :- (Note: Rate of modular cover plates are deemed to be included in the rate quoted)

One light point controlled by one, one way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

One 3 pin 5 Amps switch socket outlet point controlled by one switch on the same board.

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

One bell point controlled by one, bell switch 5 Amps

Description all as per item No 137 here in before but using 2.5 sq mm single core copper conductor cable FRLSH of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm FRLSH copper conductor cable PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S & F for Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

S & F for Modular Switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as specified.

S & F for Modular Switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

S & F for for Bell push modular 6 Amps single module complete all as specified.

S & F for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 40 to 63 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for Decorative wall mounted luminaire made out of polycarbonate with unbreakable globe suitable for LED bulb and provision of LED bulb 9/10 watts complete all as specified and as directed. Make Havells , Philips, Bajaj.

S & F for LED mirror light 9/10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed. Make- Bajaj Havells, Philips.

S & F for Energy saving new generation 9/10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. Make :-Havells Bajaj Philips

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make :- Make Bajaj Philips, Havells.

Supply and replacing 1100 volts grade heavy duty PVC insulated aluminium conductor, served with inner sheathing of PVC in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm dia GI suspension wire, one twin core cable of size 10 Sqmm multi -strand complete all as specified and directed.Make : Havells/Polycab

M& L for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised earth wire 4mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate No 3 of MES Schdule Part-I connected to earthing point and testing on completion with and including 15mm bore light grade GI protection pipe (upto 7.5 meter beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C-1 with RCC 1:2:4 type B-1, 40 mm thick cover reinforced with 8mm dia TMT bars 3 Nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore medium grade GI watering pipe common salt and charcoal filling, necessary excavation and earth work complete

S & F for Lamp holder, PVC body suitable for batten fitting completes all as specified.

Supply & Fix exhaust Fan steel body AC single phase 300 mm sweep with blades ,and frame and louvers complete with cavity.

Supply and fixing LED light fitting 1x 20W, 220Vc, Acdecorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceilling rose complete.

Supply and fixing LED Street light fitting 35 watt 230 v AC outdoor type with high pressure die cast alliminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistance including thermal management in multiple optics complete with IP 65/66 protection complete,

M & L PVC insulated, armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, 2 core, cross-sectional area10 sq.mm

Supply and fix sheet metal enclosure MCB distribution board, 4 way double door with IP-43 protection with 200 Amp rated bus bar complete all as specified & directed.

S & F for MCB Single pole and neutral rated capacity 32 Amps, 240 volts breaking capacity 10 KA including removal of old unserviceable one complete all as specified and as directed.

Supply & laying GI medium grade 20mm dia pipe including fittings, on walls or laying in floors complete all as specified.

S & F 20 mm Stop valves, Gun-metal, globe valves, with iron wheel head, screwed both ends for iron pipe and fixed

MS JODHI PRASAD SINGH SONS (BID ID -3296524)

M/S MSD & Associate (BID ID -3299458)

M/S JAI MATA DEE CONTRUCTION CO. (BID ID -3293748)

SARKAR BUILDERS (BID ID -3298803)

BHARATI ENTERPRISES (BID ID -3299461)

M/S ABDHESH CONSTRUCTION (BID ID -3296751)