Providing Multi Village Piped Water Supply Scheme for Gagret Constituency in Gagret Block and Chintpurni Constituency in Amb Block Distt Una (HP) (Under Jal Jeevan Mission)

Amount

Excavation in foundations and trenches (for pipes and pits in all depths etc.) in all lifts and in all kinds of soils such as pick work, jumper work, blasting in soft/hard rock, chiseling/wedging out of rock (where blasting is prohibited)and saturated soils, stacking the excavated earth within all leads and lifts, clear from the edge of excavation and then returning the stacked soil in 15 cm layers when required into plinths, sides of foundation and trenches etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by Engineer-in-charge within all leads and lifts

Providing and laying cement concrete 1:6:12 (1cement : 6 approved sand : 12 approved quarry stone aggregate.40mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material within all leads and lifts.

Providing and laying cement concrete 1:3:6(1cement : 3 approved sand : 6 approved quarry stone aggregate.40mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material within all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4meters and removal of the same for insitu reinforced concrete and plain concrete work:-

Foundation, footings, bases of columns and the like etc. and mass concrete.

Columns,pillors, posts & struts etc .from plinth level upto ground floor slab. upto First floor slab.

upto First floor slab.

Sides and soffits of beams, beam haunchings,cantilievere girders, bressumers and lintels not exceeding 1 Metre in depth: Plinth beams and Ground floor beam.

First Floor beam

Flat surfaces such as soffits of and suspended floors, roofs landing and the like: Floors etc. upto 200mm in thickeness. Ground Floor

First Floor

Staircases with sloping or stepped soffits including riser and stringers excluding landing.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttresses, plinth and string courses and the like.

Edges of slabs and breaks in floors and walls uner 20 CM wide.

Providing and laying cement concrete work 1:1.5:3 (1cement : 1.5 approved sand : 3 approved quarry stone aggregate.20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work including carriage of material within all leads and lifts.

Foundation, footings, bases of columns and the like etc. and mass concrete.

Columns,pillors, posts & struts etc .from plinth level upto ground floor slab. upto First floor slab.

Upto First floor slab.

Suspended floor roofs landing and shalves and their supports balconies, beams, girders,bressumers and cantilevers upto Ground floor beam .

upto First floor beam .

Staircases (except spired stair cases) excluding landing but including preparing the surface and finishing of nosing upto floor two level.

Walls (any thickness but not less than 0.10 mtrs. thickness) including attached pilasters, buttersses, plinth and string courses etc. from top of foundation upto floor two level.

Providing and laying cement concrete work 1:2:4 (1cement : 2 approved sand : 4 approved quarry stone aggregate.20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work in Suspended floor roofs landing and shalves and their supports balconies, beams, garders,bressumers and cantilevers upto floor two level. including carriage of material within all leads and lifts.

Providing tor steel reinforcement for RCC work including bending binding and placing in position complete upto floor two level. Tor steel.

1st Class Brick work using common burnt clay building bricks in foundation and plinth and in super structure in cement mortar 1:6 (1cement :6 approved sand) Foundation and plinth

-Do- In super structure above plinth level ( Ground Floor )

-do- (Ist Floor )

Half brick masonry in comon burnt clay building bricks in cement mortar 1:4 ( 1cement : 4 approved sand) in foundation and plinth including carriage of of all material within all leads and lifts .

Providing and Fixing anodised aluminium work (JINDLE MAKE) for door,window,ventilators and partition with extruded built up standard tubular and other sections of approved make confirming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868.(minimum anodic coating of grade AC 15) fixed with rawl plug and screws or with fixing clips,or with expansion hold fastener including necessary filling up of gaps at junctions at top,bottom and sides with required PVC.neoprene felt etc. Aluminium section shall be smooth rustfree,straight,mitred and jointed mechanically where ever required including cleast angle,aluminium,snap beading for glazing/panelling C.P. brass/stainless steel screws . All complete as per architectural drawings and the directions of Engineer-in-Charge.

15mm thick cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level i/c arrises, internal rounded and less chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in cm 1:6 (1cement :6 sand).

15mm thick cement plaster with cement mortar 1:3(1 cement:3 sand) in single coat on fair side of brick/concrete/stone walls for interior plastering all heights including arises, internal rounded angles chamfers and/ or rounded angles not exceeding 80mm in girth and finished even and smooth i) Upto floor two level

20 mm thick cement plaster with cement mortar 1:4(1 cement; 4 sand) in single coat on rough side of brick/concrete/stone walls for interior plastering all heights including arises, internal rounded angles chamfers and/ or rounded angles not exceeding 80mm in girth and finished even and smooth i) Upto floor two level

20 mm thick cement plaster with cement mortar 1:5(1 cement; 5 sand) in single coat on rough side of brick/concrete/stone walls for interior plastering all heights including arises, internal rounded angles chamfers and/ or rounded angles not exceeding 80mm in girth and finished even and smooth i) Upto floor two level

6 mm thick cement plaster to ceiling in C.M.1:3 (1Cement,3 sand) with in all leads and lifts complete in all respect.

Filling in plinth with sand under floors including watering, ramming consolidating and dressing complete. within all leads and lifts complete as per the direction of Engineer-In-Charge.

Boulder filling under floor with hard stone, with at least one broken face, hand packed properly within all leads and lifts complete as per the direction of Engineer-In-Charge.

Providing and fixing of double charge impect resistent heavy duty vetrified tiles nitco or equivalant 600x600x10mm thick auti skid water proof mm manufactured of approved shade and colour (Amazone beinge/ ice) in flooring , treads of steps and landings laid over 12 mm thick cement motor 1:3 jointed with cement slurry mixed with pigment to match the shade of tiles as required complete in all respect including all leads and lift.

White glazed tiles 6 mm thick (Nitco make ) in skirting risers of steps and dado laid over 12 mm thick cement motor 1:3( 1cement :3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete in all respect including all leads and lift.

Providing and fixing anodized aluminium shutters of doors,windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings whereever required including the cost of PVC/neoprene gasket as required (fittings and glazing/panelling shall be paid for separately)

P/F aluminium Grills of required pattrens including fixing with steel screws complete as per the direction Engineer-in-charge .

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed of dry brick/stone aggregate 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground.

Providing plinth protection 50mm (fifty millimeters )thick in cement concrete 1:3:6 ( one cement; three sand; six graded stone aggregate 20mm (twenty millimeters) nominal size) including finishing the top surface of concrete.

Providing and fixing anodized aluminum sliding doors bolts anidized colour and shade with bolts and nutts, screw, etc complete as per the direction of Engineer-In-Charge

300x16mm (Three hundred into sixteen millimeters) nominal size.

Providing and fixing aluminium tower bolts (Barrel type) anodized transparent or dyed to required shade and colour with screws etc complete as per the direction of Engineer-In-Charge

250x10mm (Two hundred fifty into ten millimeters) nominal size

150x10mm (One hundred fifty into ten millimeters) nominal size

Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etc. complete as per the direction of Engineer-In-Charge

125mm (one hundred twenty five millimeters) nominal size

100mm (one hundred millimeters) nominal size

Providing and fixing 100 mm bright finished brass floor door stopper with rubber cushion screws etc to suit shutter thickness complete

Providing and fixing M.S. hooks and eyes 150 mm. Complete within all leads and lifts as per the direction of Engineer-in-Charge

Providing and fixing hudraulic door closer of approved brand and manufacture ) complete as per the direction of Engineer-In-Charge

Distempering (Two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surface to give an even shade over and including priming coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt & remains of loose powdered materials complete in all respect i/c all leads and lift

Providing/Laying granite stone in flooring 20mm average thickness base of cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete 20mm thick.

Steel work welded in built up sections,trusses & framed work i/c cutting,hoisting & fixing in position & applying a priming coat of red lead paint In grating, framed ,guards,bars,ladders, railing, brackets & similar works within all leads and lifts as per direction of Engineer-in-charge.

Providing and fixing stainless steel railing (1.00 mtr. height)a fixed in straight length over stainless steel flat/round at top of vertical & horizontal balusters including fixing with steel screws complete as per the direction of Engineer-in Charge.

Providing and fixing 12 mm thick and 100 mm vide pelmet with 25 mm diameter wooden curtaing rod and brackets including fixing with 25x3 mm M.S. flat 10 centimeter long and plugs etc. complete in 1st class deodar wood within all leads and lifts as per the direction of Engineer-in- Charge.

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (one cement: three sand) to give smooth and even surface i/c the cost of form work & curing complete upto floor two level.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressures not less than 4.5 kg/Sqm i/c filling the joints with approved adhesive complete. (100mm dai pipes)

Providing and fixing on wall face PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete.

PVC plain bend 100mm dia

Providing and fixing M.S. holder bats clamps of approved design to CI or SCI pipesembedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix ( 1 cement : 2 sand : 4 graded stone aggregates 20mm nominal size) and cost of cutting holes and making good the wall etc. 100 mm dia for PVC pipe.

Providing 200 mm wide CI rungs with channel or ribed non slip surface including fixing in man hole with 200x100mm Cement Concrete 1:3:6 ( one cement :3 Sand : 6 Graded crushed stone agg.20mm nominal size)

Providing and fixing cast iron cover with frame havig frames size of 600 mm internal dia . including carriage of materials within all leads and lifts

Providing and fixing vent opening including cowl with mesh in the top of the tank including carriage all lead and lifts and as per direction of Engineer in Charge

Providing and fixing high pressure PVC spigot and socket soil waste and ventilating pipes ISI marked including fixing with approved adhesive etc. including carriage all lead and lifts and as per direction of Engineer in Charge

i) 75mm nominal size

ii) 110mm dia nominal size.

Providing and fixing 75mm PVC floor trap ISI marked of self f cleaning velocity complete in all respect as per the direction of engineer in charge .

Providing and fixing PVC Plain bend ISI Marke including fixing with approved adhesive etc. including carriage all lead and lifts and as per direction of Engineer in Charge

i) 75mm nominal size

ii) 110mm nominal size

Providing and fixing PVC Door bends with oval access door insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive etc. including carriage all leads and lifts and as per direction of Engineer in Charge

i) 75mm nominal size

ii) 110mm nominal size

Providing and fixing PVC door Tee complete in all respect including carriage all leads and lifts and as per direction of Engineer in Charge

i) 75mm nominal size

ii) 110mm nominal size

Providing and fixing Clamp complete in all respect including carriage all leads and lifts and as per direction of Engineer in Charge

i) 75mm nominal size

ii) 110mm nominal size

Providing and fixing Cock Brass Angle Valve 15 mm dia complete in all respect including carriage all leads and lifts and as per direction of Engineer in Charge

Providing and fixing Brass Bib Tap Long Nose 15 mm dia complete in all respect including carriage all leads and lifts and as per direction of Engineer in Charge

Providing and fixing Brass Bib Tap Short Nose 15 mm dia complete in all respect including carriage all lead and lifts and as per direction of Engineer in Charge

Providing and fixing Brass Pillar Tap ( Superior or Heavy type) 15 mm dia complete in all respect including carriage all lead and lifts and as per direction of Engineer in Charge

Providing and fixing Brass Shower 85 mm dia complete in all respect including carriage all lead and lifts and as per direction of Engineer in Charge

Providing and fixing C.P. Brass Soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws complete in all respect as per the direction of emgineer in Charge.

Providing and fixing C.P. Towel Ring complete in all respect including carriage all lead and lifts and as per direction of Engineer in Charge

Providing and fixing C.P. Brass Towel Rail complete with C.P. brass brackets fixed to wooden Plugs cleats with C.P. brass screws i.e size 600x20 mm including carriage all lead and lifts and as per direction of Engineer in Charge

Providing and fixing vitreous china wash basin with single hole for pillar tap with C.I. or MS brackets painted white i/c cutting holes & making good the same but excluding fitting i.e size 630x450 mm as per the direction of engineer in charge.

Providing and fixing china pedestal for wash basin complete recessed at rhe black for the reception of pipes and fittings of Parryware / Hindware/ CERA make as per the direction of engineer in charge. .

P/F Brass waste Coupling 32 mm wash basin, water closet & sink complete in all respect as per the direction of engineer in charge.

P/F Brass waste Pipe 32 mm wash basin, water closet & sink complete in all respect as per the direction of engineer in charge.

P/F Brass Double waste Pipe 32 mm wash basin, water closet & sink complete in all respect as per the direction of engineer in charge.

P/F Tooth Brush and tumbler holder complete in all respect as per the direction of engineer in charge.

P/F 600X450 mm bevelled edge mirror of superior glass mounted on 6 mm thick AC sheet or Ply wood sheet & fixed to wooden plug with CP brass screws & washers as per the direction of engineer in charge.

P/F C.P. Toilet Paper holder complete in all respect as per the direction of engineer in charge.

Providing and fixing white vitreous china wash down water closet (European type W.C.pan) withintegral 'P'or 'S' trap including jointing the tap with soil pipe in CM 1:1 of Parryware / Hindware/ CERA,( seat and cover to be measured and paid for seperately) as per the direction of engineer in charge.

Anglo Indian Universal Closet

Providing and fixing CP brass Jet Jaquar/Jal make with connection pipe and other fitting for (European Type) WC pan complete in all respect as per the direction of engineer in charge.

Providing and fixing single hole Sink Mixture complete in all respect as per the direction of engineer in charge.

Providing and fixing 10 liters vitreous china low level flushing cistern with a pair of C.I. or mild steel brackets complete with fitting such as lead valve with polythene float C.P brass handle, unions and couplings for connecting with inlet, outlet and overflow pipes 40mm dia. C.P flush bend including cutting holes in walls and making good the same and connecting the flush pipe with cistern and closet ( over flow pipe to be measured and paid for separately ) 10.00 liters. of Parryware / Hindware/ CERA

Providing and fixing C.P. brass grating complete in all respect as per the direction of engineer in charge.

Providing and fixing PVC connection pipe with brass unions i.e 40 cms inlet & PVC connection i/c making the wall good to wall ceiling complete in all respect as per the direction of engineer in charge.

Providing and fixing PVC connection pipe with brass unions i.e 60 cms inlet & PVC connection i/c making the wall good to wall ceiling complete in all respect as per the direction of engineer in charge.

P/F kitchen stainless steel sink with CI or MS brackets painted white including cutting holes in walls and making good the same but excluding fittings of stainless sink with drain board super deluxe No. 632 of size 161x54 cm of diamond or its equivalent make including carriage all lead and lifts and as per direction of Engineer in Charge

Providing and fixing plasic seat(solid/Hollow type) and cover for wash down water closet with C.P. brass and hinges and rubber buffers solid type White plastic seat of Parryware / Hindware/ CERA including carriage all lead and lifts and as per direction of Engineer in Charge

P/F Gate Valve 15 mm dia complete in all respect including carriage all lead and lifts and as per direction of Engineer in Charge

P/F Conceled stop cock 15 mm Dia complete in all respect including carriage all lead and lifts and as per direction of Engineer in Charge

Providing and Fixing 1000 Liters cap Sintex water Storage tank double Layer with top lid and making connections complete in all respect as per the direction of Engineer- in -Charge.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. cable :Havells, L & T and switches Anchor ,SSK make

Group C.

Wiring for twin control light point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit with 2-way, 5/6 amps. piano type switch and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.Havells, L & T and switches Anchor ,SSK make

Group C.

Supplying and fixing following rating Piano-type switch /socket on the existing switch box / cover including connections etc. as required.make Anchor ,SSK.

S.P. 5/ 6 Amps one way switch, piano type.

5 pin 5/ 6 Amps socket outlet, porcelain base/ piano type.

Supplying and fixing metal box of 180mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 5 pin 5/6 amps socket outlet and 5/6 amps, piano type switch, connections, painting etc. as required..make Anchor ,SSK

Supplying and fixing metal box of 180mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps, piano type switch, connections, painting etc. as required..make Anchor ,SSK

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 1 No.HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.Make L&T,Havells,Finolex

2x1.5 Sq. mm.

2x2.5 Sq. mm.

2x6.0 Sq. mm.

2x10 Sq. mm.

Wiring for circuit / sub-main with 4x16 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 2 No.16 Sq.mm. (4x16+2x16) HRFRLS/PVC insulated single core copper conductor cable for earthing as required.Make L&T,Havells,Finolex

Wiring for power plug with 2x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 1 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.Make L&T,Havells,Finolex

Wiring for power plug with 4x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed steel conduit along with 2 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required. Make L&T,Havells,Finolex.

Providing, Installation, testing and commissioning of K.Lite make Glazed LED 22 Watt Batten Cat. No. 1595 22 W LED T-5 TL High quality design aluminum extruded decorative end caps or its equivalent as per best satisfaction of Engineer-in-charge .

Supplying and fixing Surface mounting Bema LED down lighters (Square) polycarbonate diffuser (chrome finish frame) 16 watts K.Lite make Cat. No.7325 complete with connections etc. as required.

Supplying and fixing Surface mounting Bema LED down light round 10 watt k-light make Code No. 7665 complete with connections etc. as required..

Supplying and fixing Recess mounting LED.10 watts "DIVYA ROUND" Low height backlit round LED downlight with non integral drive k-lightmake Cat.No.7665 complete with connections etc,as required.

Supplying and fixing Recess mounting LED.18 watts "DIVYA SQUARE" Low height backlit SQUARE LED downlight with non integral drive k-lightmake Cat.No.7669 complete with connections etc,as required.

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required:- Havells velocity,Bajaj ultima,Usha technix

Ceiling Fan 1200 mm sweep, Havells make Category-A

Ceiling Fan 1400 mm sweep,Havells make Category-A

Supplying and fixing of Exhaust fan (Plastic) with Louver shutter 300mm 1000RPM `1125 Air Delivery (CMM) Bajaj make DDxl Model on the existing opening complete with connections etc. as required.Bajaj,crompton,Greaves.

Supply and fixing exhaust fan lower shutter for 300/380mm exhaust fan on the existing wall painting etc. as required.

Earthing with copper earth plate 600 mmx600 mmx 3 mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Supplying and fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required:-

Providing and fixing 25mm x 5mm copper strip in 40 mm dia. G.I. pipe from earth electrode etc. as required.

Providing and fixing 25mm x 5mm copper strip on surface or in recess for earth connections etc. as required.

Providing and fixing 8 SWG (4 mm dia.) copper wire on surface or in recess for loop earthing as required.

Extra for using salt and charcoal for pipe earth electrode complete as required.

S/F of 1.5 ton split type air conditioner as per Voltas Hot & Cold better start rating 2 virus safe filter triple filter e-saver mode white display auto clean anti bacteria filter jet cool on of timer slip mode compressure code less remote complete in all respect suitable to operate 230/240 volts + - 10% AC supply capable to perform the function of cooling dehuminification air circulation bantilation and fitting in the size of nominal cooling capacity complete with 4KBA auto matic voltage stabeliser whirl pool make cat No-DMC-LX-1640 confirming to ISI specification. The stabiliser should have high voltage trip and MCB high low voltage trip and time relay complete in all respect including carriage of material with in all leads and lifts.

Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Non-return valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. as required:-

35 Liter capacity water heater (Cat-A)

Supplying and fixing of following sizes of PVC conduit along with the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required:-

25 mm. dia

Supplying & fixing metal box of following sizes (nominal size) on surface or in recess suitable for fixing phenolic laminated sheet cover in front including painting etc. as required:-

100mm.x100mm.x60mm. deep

Supplying and drawing following size of PVC insulated, heat resistant, flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in existing surface / recessed, Steel/PVC conduit as required.

3x1.5 Sq. mm.

supplying and fixing stair light Havells make as per Cat No-LHDL07150099 - 15 watt but excluding the cost CFL complete with testing and commissioning etc as required.

Supplying and fixing LED. Lamp 10 watts E-27 Havells make in the existing batten holder

LED 10WATT Retrofit

Providing and supplying five seater sofa set including all lead and liftsas per the direction of the Engineering-in-charge.

Providing and supplying Double Bed for Rooms including all lead and lifts as per the direction of the Engineering-in-charge.

Providing and supplying S.S three seater lobby chair including all lead and lifts as per the direction of the Engineering-in-charge.

Providing and supplying Dining table with 8 chair of teak Wood including all lead and lifts as per the direction of the Engineering-in-charge.

Providing and supplying Easy chair of teak Wood including all lead and lifts as per the direction of the Engineering-in-charge.

Akarshan Jaswal

Satish Kumar Prop Suchet Engineering Corp