Provn of interlocking tiles, iron benches, shed with fiber roof sheet, counter platform with granite slab top and other sanctioned works at Mil Stn Abohar

Amount

SCHEDULE 'A' SECTION I (B&R Portion)

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in loose / soft soil all as specified and directed by Engineer - in – Charge.

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth, for foundations etc or manholes, cesspits, pipes and cables etc. not exc 10 Sqm on plan and getting out in soft / loose soil all as specified and directed by Engineer - in - Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers of soft / loose soil not exceeding 25cm thick all as specified and directed by Engineer - in - Charge.

Excavating in post holes (or similar holes) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth, in layers not exceeding 25cm, watering, and removing surplus spoil to a distance not exceeding 50m and making good surface all as specified and directed by Engineer - in - Charge.

M & L Sand filling under floors or in foundations including watering and consolidation all as specified and directed by Engineer - in - Charge.

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directed by Engineer - in - Charge.

M & L for broken bricks hard core of gauge not exceeding 63mm, deposited, spread levelled in layers n exc 15 cm thick, watered and rammed to a true surface all as specified and directed by Engineer - in - Charge.

M&L Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed by Engineer - in - Charge

M&L Cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate for foundations, fillings and mass concrete all as specified and directed by Engineer – in - Charge.

M & L RCC 1:1½ :3, (nominal mix), Type A-1 using 20mm graded stone aggregates for slabs supported on walls, beams, columns and in shelves, the like all as specified and directed by Engineer - in - Charge .

M & L for stone kerb of roughly squared stones lime or sand stone of size 20 cm x 30 cm, dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6cm for top and exposed surface of sides and 20 mm for the rest of surface jointed in cement mortar 1:6 and struck flush complete all as specified and directed by Engineer - in - Charge.

M&L Brick work with old size burnt fly ash bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed by Engineer - in - Charge .

M & L brick work with sub class ‘B’ old size burnt fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed by Engineer - in - Charge.

M&L Continuous brick edging using old size burnt clay bricks of sub class B; with width equal to width of brick laid dry on end vertically (including necessary earthwork & embedding bricks in the ground) all as specified and directed by Engineer - in - Charge.

M & L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick cement mortar 1:4 all as specified and directed by Engineer - in - Charge .

M & L form work to soffits of suspended slabs such as roof slab and similar work not exceeding 200mm thick for rough finished surfaces of concrete all as specified and directed by Engineer - in - Charge .

Taking down chowkhats or frames with shutters (with out taking off shutters from the frame) not exceeding 1.50 Sqm each all as specified and directed by Engineer - in – Charge.

Taking down chowkhats or frames with shutters without taking off shutters from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each and all as specified and directed by Engineer - in - Charge.

S&F Factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded coloured PVC ’C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed into the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site as per specification complete all as specified and as directed by Engineer-in-Charge.

S & F Solid PVC door frame factory made of size 50mmx 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube jointed , supplying and fixing in opening complete all as specified and as directed by Engineer-in-Charge.

S & F Aluminium anodised barrel tower bolt of extruded section 150mm long all as specified and directed by Engineer - in - Charge .

S & F Aluminium anodised barrel tower bolt of extruded section 200mm long all as specified and directed by Engineer - in - Charge .

S & F 75 mm long butt hinges extruded aluminium alloy with galvanised mild steel hings pin, anodised and fixed all as specified and directed by Engineer - in - Charge .

S & F aluminium handle cast type anodised, 125mm long all as specified and directed by Engineer - in - Charge .

S & F aluminium mortice lock with four levers vertical type, size 75mm with necessary screws etc complete all as specified and directed by Engineer - in - Charge.

S & F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm all as specified and directed by Engineer - in - Charge .

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-Charge.

S&F door closer hydraulically regulated, aluminium (Die cast) body, designation No. 3, universal type suitable for door shutter upto 1000mm in width complete all as specified and as directed by Engineer-in-Charge.

S&F Mild steel work as in wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh/ MS work etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 bent to shape all as specified and directed by Engineer - in - Charge.

S & F Mild steel bolts, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends; each scre-wed end to be fitted with washers and one hexagonal or square nut, exc 30cm long all as specified and directed by Engineer - in - Charge.

M & L mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia all as specified and directed by Engineer - in - Charge .

S & F steel work in tubular trusses etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1979 (grade st-240) all as specified and directed by Engineer - in - Charge.

S & F steel windows or ventilators, fixed type, with glazing bars all as specified and directed by Engineer - in - Charge.

S&F anodized aluminium frame for doors, windows, ventilators, partitions etc., with one or more rebates including joining cleat for fixing etc complete all as specified and as directed by Engineer-in-Charge.

S&F Anodised aluminium door shutters with Powder Coating (minimum thickness of powder coating 50 micron), aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed by Engineer-in-Charge.

S&F anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed by Engineer-in-Charge.

S&F anodised aluminium grill diamond shape 100mmx100mm aperture of 6mm dia round bars including necessary joining cleats, clips, anodised aluminium snap beading, screws, complete all as specified and as directed by Engineer-in-Charge.

S & F fiber glass reinforced translucent 2mm thick corrugated sheeting with two corrugation side lap fixed with “L” type or “J” type hook or cranked hook bolts all as specified and directed by Engineer - in - Charge.

M & L for 75mm thick cement concrete type C-2 (1:3:6) using 40mm graded stone aggregate as in plinth protection etc all as specified and directed by Engineer - in - Charge.

M & L for 100mm thick cement concrete type D-2 (1:4:8) using 40mm graded stone aggregate as in sub floors, sub bases etc all as specified and directed by Engineer - in - Charge.

M & L 100mm thick Cement Conrete 1:2:4 type B–1 using 20mm graded stone aggregates flooring finished even and smooth without using extra cement all as specified and directed by Engineer - in – Charge .

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. all as specified and directed by Engineer - in – Charge.

M & L for glazed ceramic coloured tiles 7mm thick 350x 250mm/ 450X 350mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 10mm thick cement sand plaster (1:3) complete all as specified and directed by Engineer - in - Charge.

M & L for glazed ceramic coloured tiles 7mm thick 300 x 450mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over and including 10mm thick cement sand plaster (1:3) complete all as specified and directed by Engineer - in - Charge.

M & L for non skid ceramic coloured tiles with matt finish, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement paste pigmented to tile shade over and including 15mm thick cement and sand screed (1:4) complete all as specified and directed by Engineer - in - Charge.

M & L machine pressed precast concrete interlocking paver blocks any size and shape factory casted with grey cement and pigment and conforming to IS 15658-2006 of 80mm thickness, M-40 Grade and laid over and including 25 mm thick sand cushion and joints filled with sand complete all as specified and directed by Engineer - in - Charge.

Dismantling floor or wall tiles including cement mortar bedding, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer - in – Charge.

M & L 5mm thick rendering in Cement Mortar 1:3 on fair faces of brick work or concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer - in - Charge .

M & L rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even & smooth without using extra cement all as specified and directed by Engineer - in - Charge .

Taking down cement plaster/ terrazo finish on brick wall including racking out joints, hacking for keys scrubbing down with water all as specified and directed by Engineer - in - Charge.

M & L three coats of white wash including preparing new plastered or unplastered surfaces of walls complete all as specified and directed by Engineer - in - Charge.

M & L three coats of white wash including preparing new plastered or unplastered surfaces of ceiling complete all as specified and directed by Engineer - in - Charge.

M & L applying two coat of cement base paint on new plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in – Charge

S & F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane all as specified and directed by Engineer - in - Charge .

S & F 5.5mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane all as specified and directed by Engineer - in - Charge .

S & F figured glass 3mm thick pin head type and glazing with oil putty and securing with glazing pins not exceeding 0.50 Sqm in each pan complete all as specified and directed by Engineer - in - Charge .

M & L providing two coats of synthetic enamel paint and a coat of red oxide primer on new steel surfaces including preparation of surface of any description over 10 cm width or girth all as specified and directed by Engineer - in - Charge .

S & F 15mm bore medium grade steel tubes galvanised with all fittings and fixed complete to walls & ceiling or laid in floor all as specified and directed by Engineer - in – Charge .

Taking down steel tubing 15mm bore and connections including cleaning for refixing/ removal complete all as specified and directed by Engineer - in – Charge.

S&F bib taps 15mm bore dia, fancy type, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe all as specified and directed by Engineer – in – Charge .

S&F Pillar taps 15mm bore dia, cast copper alloy with capstan heads chromium plated screwed down hidh pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed by Engineer – in – Charge .

S & F 15mm bore stop valve, fancy type, chromium plated cast copper alloy screwed down, high pressure, with long shank and cup (concealed type) with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified and directed by Engineer - in – Charge.

S & F grating round 125mm with waste hole of PTMT (minimum weight 40 gms) all as specified and directed by Engineer - in - Charge.

S & F in repair PVC connection 15mm size with PTMT nuts of length 450mm all as specified and directed by Engineer - in – Charge.

S&F in repairs vitreous china wash down water closet (Padestal pattern) White, including plastic water closet seat cover, black, closed pattern with flat bottom with mild steel chromium plated or aluminium hinging device and fixing with all joints including connection to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, ball valve and float including brackets, flush pipe of PVC 32mm bore and connection to WC pan complete all as specified and directed by Engineer - in - Charge .

S & F vitreous china wash basin, white, flat back, size 550x400mm including waste fitting brass chromium plated, PVC connection and PVC waste pipe and fixing with new brackets including cutting and pinning in ends of brackets complete all as specified and directed by Engineer - in – Charge .

S & F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified and directed by Engineer - in - Charge .

S & F brass chromium plated shower rose 125mm size with or without swivel joint any size including fixing to steel pipe or union all as specified and directed by Engineer - in - Charge.

Demolition of brick work built in cement mortar all as specified and directed by Engineer - in - Charge.

M & L applying two coat of cement base paint over one coat of white wash on new plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer - in – Charge

M & L for two coat of oil bound distemper over a coat of clearcolle primer on newly plastered surface of wall including preparation of surfaces complete all as specified and directed by Engineer - in – Charge

S & F drapery curtain rod fancy type 25mm dia, fabricated out of mild steel sheet not less than 20 gauge, including brackets and pair of decorated end knobs (finials), stop roller etc, pretreated powder coated natural color complete all as specified and directed by Engineer - in - Charge.

S & F PVC flexible waste pipe of 90 cm long and 32mm dia with PVC cap suitable for waste coupling all as specified and directed by Engineer - in - Charge .

S & F Iron garden bench with back rest 1500 mm (L) x 600 mm (W) x 1000 mm (H) with arms complete all as specified shown in drawing and directed by Engineer - in - Charge Model DGB-011 of make Dwarka India or equivalent model in make as approved by GE.

M & L rendering 15mm thick on fair faces or other than fair faces of brick work in CM 1:6 finished even and smooth without using extra cement all as specified and directed by Engineer - in - Charge .

SCHEDULE 'A' SECTION-II (E&M PORTION)

Taking down carefully aluminium / Copper point wiring (light, fan, socket or power, bell complete fittings such as sockets, ceiling roses, pendants, battens/ conduits, holders, regulators and making good the disturbed surfaces of walls, floors, ceiling etc all as specified and directed by Engineer - in - Charge

M & L point wiring complete with 1.5 Sqmm (nominal area) PVC FRLS insulated unsheathed copper stranded conductor cable with colour code in and including medium grade rigid PVC conduit with tees, bends, elbows, couplers, MS junction boxes concealed after cutting chases in wall, floor etc and making good to match with existing surface including sunken iron terminal box, 3mm thick bakelite sheet cover, clips, pipe hooks, brass screws, washers and 1.5 Sqmm single core stranded / solid copper conductor 1100 volts grade PVC insulated and unsheathed cable as earth continuity conductor to common earth and connecting to earth dolly for One light /bell point/ fan point controlled by one, one way switch all as specified and directed at site by Engineer – in – Charge.

All as per item No. 81 here in before but for socket out let 3 pin 5 amp on same board all as specified and directed by Engineer - in - Charge

All as per item No. 81 here in before but for socket out let 3 pin 5 amp on independent board all as specified and directed by Engineer - in - Charge

All as per Srl item No. 81 here-in-before but with 2.5 Sqmm single core multi stranded copper conductor of 1100 volts grade PVC FRLS insulated and unsheathed cable for one multipurpose switch socket outlet 6 pin, 15 Amps on independent board including 1.5 Sqmm single core stranded / solid copper conductor 1100 volts grade PVC insulated and unsheathed cable as earth continuity conductor to common earth and connecting to earth dolly.

S&F lamp holder, PVC / polycarbonate type with back plate for batten fittings all as specified and directed by Engineer - in - Charge.

S & F switch piano flush type single pole one way 5 Amp all as specified and directed by Engineer - in – Charge.

S & F switch piano flush type single pole one way 15 Amp all as specified and directed by Engineer - in – Charge.

S&F socket outlet 2 in 1, 3 pin, 5 Amps, flush type all as specified and directed by Engineer-in –Charge.

S&F socket outlet 2 in 1, 3 pin, 5 and 15 Amps, flush type complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing plug and socket type DB (Functional Unit) 20 Amps capacity with provision of single pole 20 Amps MCB, Plug top and earth plug, grouted flush to walls complete all as specified and directed by Engineer-In-Charge. Make : Legrand/Havells /C&S/Standard/Schneider or equivalent

M & L for sub main wiring comprising single core, 2 Runs of 4 Sqmm nominal cross sectional area multistranded copper conductor cable, PVC insulted unsheathed 1100 Volts grade drawing in and including appropriate dia. In PVC conduit and its fittings complete including provision of 1 x 4.0 Sqmm nominal cross sectional area multistanded copper conductor cable, PVC inslated unsheathed 1100 Volts grade as earth wire complete incl taking down old UNSV sub main all as specified and directed by Engineer-In-Charge. (Note : Extra length of cables/wire required for connection to MCBs shall not be measured)

S & F sheet metal enclosure TPN DB having facility to fix MCB in incomer and MCBs in outgoing, TPN 4 ways, Double door type complete fitted with bus bars, neutral links, blanking plates including making good disturbed surfaces with cement plastering complete all as specified and directed by Engineer-In-Charge. (Make : Legrand/L&T Hanger/C&S/INDO KOPP)

S & F MCB single pole 6 to 32 Amp 240 volt with rupturing capacity not less than 10 KA all as specified and directed by Engineer – in – Charge .

S & F MCB, Single pole & neutral, 240 Volt, 63 Amps, braking capacity 10 KA all as specified and directed by Engineer - in - Charge.

S & F MCB triple pole & neutral 63 Amp 440 volt with rupturing capacity not less than 10 KA all as specified and directed by Engineer – in – Charge .

S & F ceiling rose 65 x 50mm three terminals PVC/ polycorbonate, isolated body all as specified and directed by Engineer - in - Charge .

S&F as in repairs fan regulator electronic stepped heavy duty flush type 230 volt AC single phase fixed on laminated sheet top cover after cutting necessary chases to required size complete connections all as specified and directed by Engineer-in-Charge.

M&L LED tube light fixture, environmental friendly energy efficient ready to use 18W LED 6000K (4') complete Syska LED or equivalent model of make Havells/ Crompton Greaves/ Philips / Wipro as approved by GE. Note : Warranty and test certificate of LED light fittings to be produced before incoporating.

M&L Batten for LED tube light lighting fixture with extruded aluminium heat sink, environmental friendly energy efficient ready to use with 18W LED 6000K (4') including electric connection with PVC copper flexible twin core cable, 1.0 Sqmm from ceiling rose to light fitting complete Syska LEDor equivalent model of make Havells/ Crompton Greaves/ Philips / Wipro as approved by GE. Note : Warranty and test certificate of LED light fittings to be produced before incoporating.

Supplying and installation of storage type 25 litres vertical geyser including temperature control system complete with all fittings and accessories, outer body of geyser should be plastic inner with stainless steel, 230 V AC, 1500 watts, ISI Mark, minimum three star rating including cement work for make good disturbed surface area all as specified and as directed by Engineer-in-Charge.

S & F 15mm bore medium grade steel tubes galvanised with all fittings and fixed complete to walls & ceiling or laid in floor all as specified and directed by Engineer - in – Charge .

S&F bib taps 15mm bore dia, fancy type, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe all as specified and directed by Engineer – in – Charge .

S & F 15mm bore stop valve, cast copper alloy screwed down, fancy type, chromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified and directed by Engineer - in – Charge.

S & F PVC connection 15mm size with PTMT nuts of length 450mm for hot water/cold water connection all as specified and directed by Engineer - in – Charge.

KATARIA CONSTRUCTION

CHILLANA CONSTRUCTION COMPANY

G S CONSTRUCTIONS