PROVN OF TOILET BLOCK NEAR BLDG NO LS-28, LS-29, PROVN OF KOTA STONE FLOORING AT BLDG NO CH-02 AND PROVN OF PATH WAY WITH OVERHEAD SHED FROM BLDG NO P-18 TO T-5 AT LEKHAPANI

Amount

Surface dressing n.exc 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundations,manholes,laying cables,pipe lines,etc and getting out in soft/ loose soil complete all as specified and directed.

Excavating over areas n exc 1.5m deep and getting out in soft/loose soil complete all as specified and directed.

All as per item No.4 above but exc 1.5 m deep and n. exc 3 m deep complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm of soft loose soil,complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum,getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

M&L PCC (1:4:8) type D-2, (using 40mm graded stone aggregate) as in foundations, filling, mass concrete etc complete all as specified and directed.

M&L PCC ( 1:3:6) type C-2 (using 40 mm graded stone aggregate), as in foundations, bed concrete,filling sub base, surface channels and mass concrete,etc complete all as specified and directed.

M&L PCC (1:2:4) type B.-2, (using 40mm graded stone aggregate) as in foundations, filling, mass concrete etc complete all as specified and directed.

M&L RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in foundations, including rafts,footings,plinth beams; etc comlpete all as specified and directed.

M&L RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in slabs, supported on walls beams and columns in floors, roofs, landings, balconies, canopies, deck slabs,in shelves and the like including slabs of septic tank, soak well etc complete all as specified and directed

M&L RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

M&L Precast RCC M-25 (Design mix) (using 20mm graded stone aggregate) as in cover slabs for manholes, septic tanks,soakage well,etc and set in CM (1:4) with plain fair faces incl chamfered, weathering, throating etc incl necessary form work complete all as specified and directed.

M&L Providing PCC(1:2:4) type B1, (using 20 mm graded stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges and other similar bands including use of formwork complete all as specified and directed.

Use and waste of form work to sides of concrete foundation, footings, base of coloumns, raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished flat surfaces of concrete complete all as specified and as directed.

Use and waste of form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels. Cantilevers, shelves including supports, overhangs, etc also splays between floor and beam etc for rough finished flat surfaces of cocrete complete all as specified and as directed.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, for rough finished flat surfaces of concrete complete all as specified and directed.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

M&L Brickwork with subclass ‘B’ bricks, straight for curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed.

M&L Brickwork with sub class ‘B’ bricks in one brick thick honey comb walling, built in CM (1:6) complete all as specified and directed.

M&L Loose filling with broken brick aggregates of gauge 80 to 150 mm in soakage pit, soak well etc complete all as specified and directed

S&F Steel ventilators fixed type complete with glazing bars dovtailed or welded,etc complete all as specified and as directed.

M&L Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisturproof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ S & F Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

S&F 150 mm size, aluminium anodised , barrel tower bolts of extruded section & fixed complete all as specified and as directed.

S&F 100mm butt hinges, type B-21, extruded aluminium alloy with galvanised mild steel hinge pin, anodised & fixed to PVC door complete all as specified & as directed.

S&F 150mm size aluminium handles, cast type, anodized and fixed complete all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5sq. m in each pane complete all as specified and as directed.

S&F Galvanised steel wire cloth. 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with steel wire staples complete all as specified and directed.

M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per Item 32 above, but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders,etc complete all as specified and directed.

S&F Mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St.-240 complete all as specified and directed.

S&F Rolled mild steel as in main and cross beams, hips and jack rafters, purlins where connected to commen rafters and running rails and similar works fixed with angle cleat or other connecting plates Fe 410-W (Gde E- 250) quality-A complete all as specified and as directed.

S&F Rolled mild steel Plates (plain or chequred) channels, square cut or notched (ordinary and counter sunk) forming holes, with out any attachment conforming to Fe:410-W(Gde-E-250) quality-A complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n. exc 5 cm long and 11 to 15 mm dia,complete all as specified and directed.

M&L for pre-painted hot dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed

M&L for pre-painted hot dip aluminium-zinc alloy metallic coated Plain steel sheet, any pattern corresponding to IS15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550 MPa as in Evas roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed

Demolition of unreinforced cement concrete in ground floors and pavings n. exc 15 cm thickness (below or above ground level) and removing debris beyond the premises,complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises,complete all as specified and directed.

M&L Hardcore of broken stone boulder of gauge n exc 63 mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to true surface all as specified and directed.

M&L 25mm thick PCC (1:2:4) type B-1, (using 20mm graded stone aggregate) as in floors and surface finished with even and fair without using extra cement complete all as specified and as directed.

M & L for Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and grainite finish polishing complete over 20mm thick cement screed bed in CM (1:4) complete all as specified and as directed by Eng-in-charge.

M&L for Machine cut Pre polished Kota stone slab flooring 15-18mm thick over 10mm thick cement screed of CM (1:4 ) base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and grainite finish polishing as in risers of steps, skirting, dado etc complete all as specified and as directed by Eng-in-charge. Note : (Kota stone to be fixed in staircase thread shall be of single piece)

M&L Coloured non skid joint free ceramic tiles of 7mm to 8mm thick area of each tile exceeding 0.11 sqm but not exceedin 0.18 Sqm as in floors, etc. and set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer in CM (1:6) for laying floor finishes complete all as specified and directed.

M&L for 300mm x 300mm heavy duty out door ceramic tiles 8 to 10mm thick (Capsule ,terracotta, Star or beige or coin Pattern) in floors etc over and including screed bed or bedding layer of mortar 15 mm thick in CM (1:6) for laying floor finishes set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L Glazed coloured ceramic tiles of size 300x450x6 to 7mm thick, as in vertical surfaces such as skirting,dado,etc and set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles laid over and including 10 mm thick rendering as in backing wall plaster in CM (1:4) complete all as specified and directed.

M & L 50 mm thick PCC (1:3:6) type C-2, (using 40 mm graded mechanically crushed stone aggregates) as in plinth protection / pavings/shafts laid in 1:20 slope including making joints at 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/ 25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement, complete all as specified. Note: The concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm, complete as specified and directed.

M & L for Chequered cement concrete tiles cast in rubber moulded glossy finish of approved colour general purpose double layer of size 25cm x 25cm x 22mm thick with mixture of white and grey cement in equal proportions and pigments set and jointed and pointed in neat cement slurry in floor incl layer over 15mm thick bedding of CM (1:6) complete all as specified and as directed

M&L for 15 to 17 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L Rendering 10.mm thick plaster in CM (1:6) on fair faces of brick work or concrete surfaces including finishing top even and smooth without using extra cement complete all as specified & directed.

M&L Rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces including finishing fair and even complete all as specified and directed.

M&L Preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed

M&L Prepration of newly plastered surface of wall and applying two coats of cement base paint complete all as specified and directed.

M&L Preparation of new steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paintover a coat of red oxide primer complete all as specified and directed.

S&F 15 mm dia bore of pipes, (medium grade), galvanised iron, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F 20 mm dia bore of pipes, (medium grade), galvanised iron, with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F Vitreous china wash down water closet, "Orissa pattern, size, 580x440mm white, with integral foot rest (excluding flushing cistern and flush pipe) but including provision of P or S trap embedded in cement concrete bedding,etc complete all as specified and directed.

S&F, Wash basins white, vitreous China, flat back, size 580x450mm, excluding taps, waste, chain and plug and porcelain stopper but including brackets fixed to wall complete all as specified and directed.

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and as directed.

S&F 40 mm Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sqm as in waste water pipes complete fixed all as specified and directed.

S&F 32mm waste coupling of PTMT (half or full threaded) (minimum weight 40mm-60 gms) fixed complete all as specified and as directed.

S&F PVC High/Low level flushing cistern 10 litres capacity including all fittings i.e float valve, syphon, flush pipe, brackets,etc complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F 15mm dia Bib taps,fancy type long body cast copper alloy, chromium plated screwed down to iron pipe or for brass ferrule & fixed complete all as specified and directed.

S&F 15mm dia pillar taps,fancy type swan long neck suitable for countershunk basin, cast copper alloy with capstan heads, chromium plated , screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks & fly nuts, screwed for iron pipe & fixed complete all as specified and directed.

S&F 15mm bore dia angle valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks of 1000 Ltrs capacity,(cylindrical vertical with closed top) double layered hoisted and fixed in position all as specified in SSR part-I & as directed.

S&F 20 mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball, screwed for iron pipe & fixed (Minimum weight 210 gms) complete all as specified and directed.

M&L 75 mm dia PVC (SWR) floor trap/nahani trap, plain with grating including jointing with solvent cement in repair complete all as specified and directed.

S&F PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints, laying in trenches/floors complete all as specified and as directed.

S&F PVC (SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F PVC (SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints, laying in trenches/floors complete all as specified and as directed.

S&F PVC (SWR) bends 110 mm dia any radius all as specified and directed.

S&F PVC (SWR) bends 75 mm dia any radius all as specified and directed.

S&F PVC (SWR) vent cowl 75 mm fore fixed with pipe complete all as specified and as directed.

S&F PVC (SWR) pipes 160 mm dia single socketed, in any length with rebber ring joints laid in trenches or in floors complete all as specified and as directed.

M & L for Point wiring with 1.5 Sqmm copper conductor unsheathed, multistranded, PVC insulated, single core cable FRLSH with earth continuity conductor of 1.5 sqmm PVC insulated copper conductor and including concealed type rigid PVC conduit of suitable size but not less than 20mm dia. and all accessories fixed to the surface of the roof/ walls etc., including terminal boxes made out of MS sheet of thickness should be not lessthan 1.2mm thick for fixing of switches, fan regulators socket outlet etc along-with 3mm thick top laminated bakelite sheet and modular box for housing switches etc, for one light /Fan /Ex Fan point controlled by one, one way switch including making good all disturbed work to match the existing complete all as specified and as directed.

All as per Item No.82 above,but One socket outlet 3 or 5 Pin, 6 Amp on same board, complete all as specified and directed.

All as per Item No 82 above but with 2.5 sqmm copper cable in and including concealed type rigid PVC conduit complete all as specified and as directed for socket outlet 3 or 6 pin 15 Amps,complete all as specified and as directed..

S&F Switch piano flush button, single pole, one way 5 Amp complete all as specified and directed.

S&F Socket outlet, 2 in 1, 5 pin 5 Amp flush type complete all as specified and directed.

S&F Switch socket combination, 5 in 1, multipurpose 5/15 Amps flush type universal complete all as specified and directed

S&F Ceiling rose surface type bakelite 65x50mm three terminal all as specified and directed.

S&F LED tube light fitting 4 ft. 1 x 18/20 watt with 230 volts, complete with all accessories internally pre-wired and fixed to walls/ceiling with screw including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

S&F LED building security light fitting 1 x 35 Watt new generation energy saving and environmental friendly long life LED street light made up of pressure diecast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening seperate driver compartment with IP65 protection incl mounting bracket of suitable size and connection complete all as specified and directed. .

S&F DB,SPN wall mounting type,240 Volts, 4 Way with 200 Amps rated bus bar,double door suitable for fixing MCB's including connecting etc complete all as specified and directed.

&F MCB single pole and neutral (SP&N) 32 Amp 240 volts 10 KA 'C' series with all incoming/outgoing connections with proper size lugs complete all as specified and directed.

S&F MCB single pole (SP) 6 to 32 Amp 240 Volts 10 KA 'C' series with all incoming/outgoing connection with proper size lugs complete all as specified and directed.

Supply and spread river sand in trenches as cable cushioning 8 cm below the cables and 15 cm above the cable all as specified and directed. Note: Punned thickness shall be measured for payment purpose.

Supply and lay burnt bricks sub class 'B' standard size laid across the cable in trenches as protection to the cable complete all as specified and directed.

Supply and laying GI pipe, 40 mm bore (light grade) in trenches/under floors or roads or along the pole incl clamp with suitable nuts & bolts for protection of cables complete all as specified and directed.

Supply,laying and testing of LT XLPE cable, insulated, screened PVC bedded, galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 volts grade with glanded aluminium conductor of cross sectional area 10 sqmm 2 core laying or passing through pipe/wall/floor/trenches complete all as specified and directed.

S&F Exhaust fans with louvers 300 mm sweep, 1440 RPM, Heavy duty single phase 240 Volts, AC 50 Hz, steel body and connecting up including louvers including making necessary opening on stone /brick masonry wall of suitable size, finishing it properly and making good with matching colour with the surroundings provision of cable 3 core of suitable size from ceiling rose to fan complete all as specified and as directed.

M&L Cutting existing steel tubing for alteration or addition (each cut measured ) bore of pipe 40 mm / 50 mm /80mm complete all as specified and directed.

M&L Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) complete all as specified and directed.

S&F GI water tubing, 25 mm dia (medium grade) including fittings/accessories like sockets, bend, elbow, union etc laying in trenches/wall/road complete all as specified and directed.

S&F GI water tubing, 20 mm dia (medium grade) including fittings/accessories like sockets, bend, elbow, union etc laying in trenches/wall/road complete all as specified and directed.

M&L Gunmetal globe/gate valve of size 25 mm bore, ISI marked, with iron wheel head, screwed both ends complete all as specified and directed.

M&L Gunmetal globe/gate valve of size 20 mm bore, ISI marked, with iron wheel head, screwed both ends complete all as specified and directed.

M&L Boring of holes by using trenchless technology under road, pavement, hard standing by for passing the cable through GI pipe complete all as specified and directed by Engr -in-Charge

M & L Brick valve chamber of internal size 90 cm x 90 cm x 90 cm by using brick masonry with with 23 cm thick wall in CM (1:6) including excavation, earth work in any strata,75 mm thick PCC (1:4:8) foundation type D-2 (using 40 mm graded stone aggregate), including 20 mm thick PCC (1:2:4) type B1(using 20 mm graded stone aggregate) on top of brick walls and plastering the internal and external surfaces with 10 mm thick CM (1:4), providing 3.15 mm MS sheet chamber cover double opening arrangement center lock system with40x40x6mm angle iron frame duly painted with two coast of black bituminous paint over one coat of red oxide primer complete all as specified and directed by Eng-in-charge.

Material and labour for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to galvanized iron earth lead wire 4mm dia, (main earthing lead ) by means of galvanized bolts, nuts and washers all as shown in electrical plate No 3 of MES Schedule Part-I (2009) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 15 mm dia GI pipe (light grade) for earth lead protection pipe for suitable length and GI pipe 20 mm dia (light grade) for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6) type C-1(using 20 mm graded stone aggregate) for earth pit and 40 mm thick pre-cast RCC coverby using (1 : 2 : 4) type B1(using 20 mm graded stone aggregate) with 3 Nos 8 mm dia TMT bars both ways and testing on completion,complete all as specified and directed by Engineer-in-Charge.

FREEZCON

RC CONSTRUCTION

STANDARD ELECTRIC WINDERS

ADNEEDS ENTERPRISE

M/s PRABIR ENTERPRISE

M/S SINGH TRADERS