Construction of Apiculture building.

Amount

Site Development, Building Portion, Water Supply, Sanitary Installation and Electrical Installation

Cutting in all kinds of earth work and disposal of all excavated earth upto all leads, lifts and carriage of material complete in all respect as per satisfaction of Engineer-in-charge.

Excavation in foundation trenches etc. in all kinds of soil such as pick work, jumper work including chiseling / wedging etc. with all lifts stacking the excavated soil not more than 3 metres clear from the edge of excavation and then returning the stacked soil in 15 cm layers, when required into plinth sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with all leads and lifts of material as directed by the Engineer-in-Charge.

Excavation in all kinds of earth work such as pick work, jumper work, including chiseling/wedging etc. and disposal of all excavated earth upto all leads, lifts and disposed earth to be leveled and neatly dressed complete in all respect as per satisfaction of Engineer-in-charge.

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete including all leads and lifts of material as directed by the Engineer-in-Charge.

Form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies height of propping and centring below supporting floor to ceiling not exceeding 4 metres and removal of the same for insitu-reinforced concrete complete and plain concrete work including all leads and lifts of material as directed by the Engineer-in-Charge. a) Foundation footings, bases of column etc. and mass concrete.

b) Beams, cantilever, girders and lintel : Sides and soffits of beams, beam haunchings, cantilevers, girders bressumers and lintels not exceeding 1 metre in depth.

c) Flat surface such as soffits of suspended floors, roofs landing and the like Floor etc. upto 200mm in thickness.

d) Stair cases with sloping or stepped soffits including risers and stringers excluding landings.

e) Columns, pillars, posts and struts: Square rectangular polygonal in plan.

f) Vertical surface such as walls (any thickness) partitions and the like including attached pilasters burresses, plinth and string course and the like.

Providing and laying cement concrete 1:6:12 (one cement: six sand and twelve graded stone crushed aggregate 40mm (forty milimetre nominal size) curing complete excluding cost of form work in foundation and plinth in all leads and lifts of material as directed by the Engineer-in-Charge.

Providing and laying cement concrete 1:8:16 (one cement : eight sand : sixteen graded stone crushed aggregate 20mm nominal size)and curing complete on slab and floor excluding the cost of form work screed laid under flooring complete in all respect as per satisfaction of Engineer-in-charge.

Providing and laying cement concrete work with concrete mixer and vibrator mix 1:5:10 (one cement five sand : ten graded stone aggregate 40mm (forty milimetre) nominal size) and curing complete excluding cost of form work in foundation and plinth in retainting / breast wall complete in all respect as per satisfaction of Engineer-in-charge.

Providing and laying upto all floor level reinforced cement concrete 1:3:6 (one cement : 3 sand : 6 graded stone aggregate 20mm nominal size) to give a smooth and even surface centering and shuttering etc. but excluding cost of reinforcement complete in all respect as per satisfaction of Engineer-in-charge. a) Moulding as in cornices window sills etc. not exceeding 15cm in girth.

Providing and laying damp proof course 38mm thick with cement concrete 1:2:4 (one cement : two sand : four graded stone crushed aggregate 12.5mm nominal size) and curing complete including all leads and lifts of material as directed by the Engineer-in-charge.

Providing and laying damp proof course to horizontal / vertical surfaces with cement mortar 1:2 (one cement : two sand) and curing complete in all respect as per satisfaction of Engineer-in-charge. a) 20mm thick

Applying a coat of hot bitumen (maxphalt 80/100) or equivalent using 1.70 kg. per square metre on damp course after cleaning the surface with piece of cloth lightly soaked in kerosene oil including all leads and lifts of material as directed by the Engineer-in-charge.

Providing and laying cement concrete work with concrete mixer and vibrator mix 1:1.5:3 (one cement one and half sand: three graded stone aggregate crushed aggregate 20mm (twenty millimetre nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in all leads and lifts as directed by the Engineer-in-charge. a) Foundations, footings bases of column and the like and mass concrete.

b) Suspended floor roofs, landings and shelves and their supports balconies, beams girders, bressurmers and cantilevers upto all floor level.

c) Columns pillars, posts and struts upto all floor level.

d) Stair cases (except spiral stair cases) excluding landings but including preparing of the surface and finishing of nosing upto all floor level.

e) Walls (any thickness but not less than 0.10m thickness) including attached pilaster, buttresses plinth and string courses etc. from top of foundation up to all floor level.

Providing TMT steel reinforcement for R.C.C. work including bending binding and placing in position complete upto all floor level including all leads and lifts of material as directed by the Engineer-in-Charge.

2nd class brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:6 (one cement : six sand) including all leads and lifts of material as directed by the Engineer-in-Charge.

2nd class brick work using common burnt clay building bricks in superstructure in cement mortar 1:6 (one cement: six sand) including all leads and lifts of material as directed by the Engineer-in-Charge.

2nd class half brick masonry using common burnt clay building brick in superstructure in cement mortar 1:4 (one cement: four sand) including all leads and lifts of material as directed by the Engineer-in-Charge.

Providing and fixing anodized aluminium sliding door bolt anodized transparent or dyed to required colour and shade with bolts and nuts screws etc. complete including all leads and lifts as directed by the Engineer-in-Charge. a) 300 x 16mm (three hundred into sixteen milimetre)

b) 250x16mm (two hundred fifty into sixteen milimetre)

Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etc. complete including all leads lifts of material as directed by the Engineer-in-Charge. a). 200x10mm (two hundred into ten milimetre)

b). 150x16mm (one hundred fifty into ten milimetre)

c). 100x10mm ( one hundred into ten milimietre)

Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etc. complete including all leads and lifts of material as directed by the Engineer-in- Charge. a) 125mm (one hundred twenty five milimetre)

b) 100mm (one hundred milimetre)

Providing and fixing anodized aluminium and dyed to required shade with polyester powder coated aluminium thickness of polyester powder coating 50 micron for doors, windows, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS-733 and IS-1285 anodized transparent or dyed to required shade according to IS-1868 (minimum anodic coating of grade AC-15). Fixed with rawl plug and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, wherever required including cleat angles, aluminium snap beading for glazing/paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the direction of Engineer-in-Charge (Jindal / Hindalco make). a) For doors, windows ventilators & glazed partition frames.

b) For shutters of doors, windows and ventilators including providing and fixing hinges pivots and making provision for fixing of fittings. Where ever required including the cost of PVC/neoprene gasket required (fittings and glazing / paneling shall be paid for separately.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc. with PVC/ neoprene gasket etc. complete as per architectural drawing and the directions of Engineer-in-Charge (cost of aluminium snap beading shall be paid in basic item). a). Glass panes of 5.5mm thickness (weight not less than 13.75 Kg/Sqm).

b). Glass panes of 4mm thickness (weight not less than 10.00 Kg/Sqm).

Providing and fixing 12mm thick both side pre-laminated particle board flat pressed three layer or graded good particle board confirming to IS 12823 grade 1 type II in paneling fixed in aluminium doors, window shutters and partition frames with CP brass / stainless steel screw etc. complete in all respect as per satisfaction of Engineer-in-charge Action tesa / Green ply.

Providing and fixing Aluminium anodized powder coated pattern to existing window /ventilator with 80mmx80mm panels holes with 8mm dia aluminium rod in window and ventilators including fixing with aluminum channel base frame in aluminium screws or nuts and bolts etc complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing double action hydraulic floor spring of Godrej Make and conforming to IS::6315for aluminium doors including cost of cutting floors as required embedding in floors and covers plates etc. complete as per the direction of Engineer-in-Charge including making good the floors etc.

Cement concrete flooring 1:2:4 (one cement: two sand: four graded stone aggregate 20mm(twenty milimetre nominal size laid in one layer finished with a floating coat of neat cement including all leads and lifts of material as directed by the Engineer-in-Charge. a) 40mm (forty milimetre) thick.

20mm (twenty millimetre) thick cement plaster skirting upto all height with cement mortar 1:3 (one cement: three sand) finished with a floating coat of neat cement including rounding of junctions with floor including all leads of lifts of material as directed by the Engineer-in-Charge.

Providing and fixing 40mm (forty millimetre) wide and 4mm (four milimetre) thick glass strip in joints of terrazzso floors including all leads and lifts of material as directed by the Engineer-in-Charge.

Kota stone slab flooring 20mm (average) thick base of cement mortar 1:4 (one cement : four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as directed by the Engineer-in-Charge. a) 25mm (twenty milimetre) thick

Kota stone slab 25mm (twenty five milimetre) thick in risers of steps skirting, dado and pillars laid on 12mm (average) thick cement mortar 1:3 (one cement: three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as directed by the Engineer-in-Charge.

White / coloured glazed jointlesss tiles 8mm (eight milimetre) thick in skirting risers of steps and dado 12mm (twelve milimetre) thick cement plaster 1:3 (one cement : three sand) and jointed with white cement slurry including all leads and lifts of material as directed by the Engineer-in-Charge (Nitco/ Johnson / Kazaria make 1st quality).

Providing & fixing 10mm thick antiskid water proof stain & impact resistant heavy duty vitrified tiles (Premium Kazaria / Nitco/ Johnson make) 600x600mm and 10mm thick manufactured of approved shade and colour in floorings, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (One cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete in all respect as per satisfaction of Engineer-in-charge.

Providing & fixing 10mm thick glossy water proof stain & impact resistant heavy duty vitrified tiles (Premium Kazaria / Nitco / Johnson make) 600x600mm and 10mm thick manufactured of approved shade and colour in floorings, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (One cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete in all respect as per satisfaction of Engineer-in-charge.

Providing and laying granite stone in flooring 20mm (average) thickness base of cement mortar 1:3 (one cement: three sand) laid over and jointed with grey cement slurry mixed pigment to match the shade of granite stone including rubbing and polishing complete. a) 20mm thick black jet.

Providing & fixing 0.60mm (point sixty milimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polister of 5 micron over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted limpet and rubber washers complete with all accessories as required as per the direction /satisfaction of Engineer-in-charge TATA / Jindal / SAIL.

Steel work welded in built up sections trusses and framed work including cuttings, hoisting, fixing in position and applying a priming coat of red lead paint including all leads and lifts of material as directed by the Engineer-in-Charge. a) In beams, joists, channels angles, tees, flats with connecting plates or angles as cleats in main and cross beams, hip and jack rafters, purlins connected to common rafter and the like.

b) In grating framed guard bars, ladders, railing, brackets and similar work.

Providing and fixing in position collapsible steel shutter with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rails of T. iron 40x40x6mm with 38mm dia steel pulley complete with bolts and nuts locking arrangement stoppers, handles including applying a priming coat of red lead paint complete in all respect as per satisfaction of Engineer-in-charge.

Painting two coat (excluding priming coat) on new steel and other matter surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter including all leads and lifts of material as directed by the Engineer-in-Charge. a) Enamel paint other than white.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete in all respect as per satisfaction of Engineer-in-charge.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete / stone / plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface complete in all respect as per satisfaction of Engineer-in-charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust & other foreign matter etc. including sand paper smooth complete in all respect as per satisfaction of Engineer-in-charge.

6mm (six milimetre) cement plaster to ceiling in cement mortar 1:3 (one cement: three sand) complete in all respect as per satisfaction of Engineer-in-charge.

15mm (fifteen milimetre) cement plaster in single coat in fair/rough side on brick concrete/stone walls for interior/exterior plastering with all height including arises internal rounded angles chamfers and/or rounded angles not exceeding 80mm (eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement: six sand) including all leads and lifts and material as directed by the Engineer-in-Charge.

Providing plinth protection 50mm (fifty milimetre) thick in cement concrete 1:3:6 (one cement: three sand: six graded stone aggregate) 20mm nominal size including finishing the top surface of concrete smooth including all leads and lifts of material as directed by the Engineer-in-Charge.

Providing under layer for plinth protection of 75mm (seventy five milimetre) thick unconsolidated bed of dry bricks/ stone aggregate 40mm (forty milimetre) nominal size) well rammed and consolidated and grouted with fine sand including preparation of ground including all leads and lifts of material as directed by the Engineer-in-Charge.

Brick edging (brick laid on edge) to plinth protection with bricks including grouting with cement mortar 1:4 (one cement: four sand) with brick size 22.9 x 11.2 x 7cm (twenty two point nine x eleven point two x seven centimetre) including all leads and lifts of material as directed by the Engineer-in-Charge.

Providing and fixing to wall ceiling and floor galvanized mild steel tube (medium grade) tube fittings and clamps including making good the wall, ceiling and floor complete in all respect as per satisfaction of Engineer-in-charge Jindal / Surya make. a) 15mm nominal bore

b) 20mm nominal bore

c) 20mm nominal bore

Providing and laying in trenches galvanized mild steel tube (Medium grade) tube fitting (earth work in trenches to be measured and paid for separately) complete in all respect as per satisfaction of Engineer-in-charge Jindal / Surya make. a) 25mm nominal bore

Making connection of galvanized steel distribution branch with galvanized mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipe complete including all leads, lifts and carriage of material complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing vitreous China wash down, water closet squatting pan (Indian type WC pan) size 580mm complete in all respect as per satisfaction of Engineer-in-charge (earth work, bed concrete, foot rest and trap to be measured and paid for separately) Cera / Hindware make. a) Orrissa Pattern

Providing and fixing vitreous china wash down water closet (European type WC pan) with integral ‘P’ or ‘S’ including jointing the trap with soil pipe in cement mortar 1:1 (one cement: one sand) complete in all respect as per satisfaction of Engineer-in-charge (Seat and cover to be measured and paid for separately) Cera / Hindware make. a) Ordinary closet

Providing and fixing plastic seat (Solid/Hollow type) art cover for wash down water closet with C.P. Brass hinges and rubber buffers complete in all respect as per satisfaction of Engineer-in-charge (Cera / Hindware make). a) Solid type Black or white plastic seat and cover.

Providing and fixing vitreous china wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings complete in all respect as per satisfaction of Engineer-in-charge Cera / Hindware make. a) Circular 460mm dia counter top

Providing and fixing C.P. brass waste for wash basin or sink complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 600x450mm beveled edge mirror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screw and washers complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing C.P. brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. brass complete in all respect as per satisfaction of Engineer-in-charge. a) 600x20mm size

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing vitreous China division plate for urinal complete in all respect as per satisfaction of Engineer-in-charge Cera / Hindware make. a) 600mmx330mm size

Providing and fixing C.P. brass bib tap with capstan head complete in all respect as per satisfaction of Engineer-in-charge Smile / Seiko / Spartan make. a) 15mm dia

Providing and fixing C.P. Brass pillar tap with capstan head complete in all respect as per satisfaction of Engineer-in-charge Smile / Seiko / Spartan make. a)15mm dia

Providing and fixing C.P. brass angle valve without nuts and pipe complete in all respect as per satisfaction of Engineer-in-charge. Smile / Seiko / Spartan make a)15mm dia

Providing and fixing PVC connection pipe with brass union complete in all respect as per satisfaction of Engineer-in-charge. a) 45cm length i) 15mm nominal bore.

Providing and fixing brass full way valve with wheel complete in all respect as per satisfaction of Engineer-in-charge. i)20mm nominal size

ii) 25mm nominal size

Providing and fixing P.V.C. water storage tank of ISI : 12701, GI inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hosting upto all height above ground level complete in all respect as satisfaction of Engineer- in-charge Sintex make three layer. a)2000 ltr. Net capacity tank

Providing and fixing PVC floor trap with grating ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Kisan / D-Plast make). a)110mmx75mm

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan /D-plast make). a) 75mm dia

b)110mm dia

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3mm thick bolts and nuts complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in charge (Finolex/Kisan /D-plast make). a) 75mm dia

b) 110mm dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make). a) 75mm dia

b) 110mm dia

Providing and fixing PVC single equal branch plain ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make). a) 75mm dia

b) 110mm dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make). a) 75mm dia

b) 110mm dia

Providing and fixing PVC plain bend ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make). a) 75mm dia

b) 110mm dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawl plugs etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make). a) 75mm dia

b) 110mm dia

Providing and fixing PVC size P or S trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Kisan / D-Plast make). a)110mm dia

Providing and fixing PTMT coloured/white high density polyethylene/poly propylene 10 litres capacity (full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, siphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia CP flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) complete in all respect as per satisfaction of Engineer-in-charge (Prayag / Cera / Hindware make).

Providing and fixing PTMT Urinal spreader of approved quality and colour complete in all respect as per satisfaction of Engineer-in-charge (Prayag or equivelant make).

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube etc. complete in all respect as per satisfaction of Engineer-in-charge. (Prayag or equivelant make).

Providing and fixing CP grating round 100mm dia of approved quality and colour complete in all respect as per satisfaction of Engineer-in-charge.

Constructing manhole with R.C.C. top slab in 1:2;4 mix (1cement: 2 sand: 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 (1cement :4 sand : 8 graded stone 40mm nominal size), inside plastering 15mm thick with cement mortar 1:3 one cement: 3 sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix 1 cement:2sand: 4graded stone aggregate 20mm nominal size finished smooth complete including curing and testing complete in all respect as per satisfaction of Engineer-in-charge. a) Inside size 800x800mm and 500mm deep including 600mm dia opening (medium duty) SFRC Man hole cover with frame. i) With 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand).

Extra for every additional depth of 0.10 Metre or Part thereof or manhole complete in all respect as per satisfaction of Engineer-in-charge. a) From 0.5 Metre upto 1.0 Metre depth

Cutting holes through existing brick work including making good the same in C:M 1:6 (1cement:6 sand) per cms depth of cutting complete in all respect as per satisfaction of Engineer-in-charge. i) holes upto and including 400 Sqcm in area.

Providing and fixing P.V.C. waste pipe 32mm dia for wash basin complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing PVC Cowl ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make). a)75mm dia

b)110mm dia

Providing and fixing vitreous China ½ stall urinal including connecting the urinal with water pipe by means of white lead mixed with chopped hamp (waste to measured and paid separately) complete in all respect as per satisfaction of Engineer-in-charge Cera / Hindware make. a)Half stall urinal flat back size 630x400x420mm

Providing and fixing 150 mm dia half round white vitreous china channel embedded with PCC 1:2:4 (one cement: two sand: four graded stone aggregate) 20mm nominal size and filling the joints with white cement complete in all respect as per satisfaction of Engineer-in-Charge Cera / Hindware make.

Providing and fixing PVC gully trap with grating brick masonry chamber in cement mortar 1:5 and water tight CI cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.53 kg. and frame to be not less than 2.72 kg. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make). a)110mm dia P type

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge. a). Extruded section profile size 48x40 mm

Providing and fixing 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge.

Providing and fixing Godrej Hydraulic door closer two speed hinges bright finished with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing aluminium hooks and eyes etc. complete in all respect as per satisfaction of Engineer-in-charge. a)150mm (One hundred fifty milimetre)

Providing and fixing 100mm aluminium door stoppers with rubber cushion screw etc. to suit shutter thickness complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing PVC on railing 50mm wide and 6mm thick as per architectural drawing to the satisfaction of the Engineer-in-Charge.

Providing and fixing colour coated curtain MS rod 25mm dia with two or three No. brackets of matching colour complete in all respect as per satisfaction of Engineer-in-charge.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5sqmm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface / recessed steel conduit and earthing the light point with 1.5 sqmm HRFRLS / PVC insulated single core copper conductor cable as required complete in all respect as per satisfaction of Engineer-in-charge (Group – A).

Wiring for twin control light point with 1.5 Sqmm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface / recessed steel conduit with 2-way, 5/6 amps. piano type switch and earthing the light point with 1.5 Sqmm HRFRLS / PVC insulated single core copper conductor cable as required complete in all respect as per satisfaction of Engineer-in-charge (Group – A).

Wiring for light plug with 2x1.5 Sqmm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface / recessed steel conduit along with 1 No. 1.5 Sqmm HRFRLS / PVC insulated single core copper conductor cable for earthing as required complete in all respect as per satisfaction of Engineer-in-charge.

Wiring for Power plug with 2x4 Sqmm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface / recessed steel conduit along with 1 No. 4sqmm HRFRLS / PVC insulated single core copper conductor cable for earthing as required complete in all respect as per satisfaction of Engineer-in-charge.

Wiring for power plug with 4x4 sqmm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface / recessed steel conduit along with 2 No. 4sqmm HRFRLS / PVC insulated single core copper conductor cable for earthing as required complete in all respect as per satisfaction of Engineer-in-charge.

Wiring for circuit /sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 NO. 1.5 Sq-mm HRFRLS/PVC insulated single core copper conductor cable or same size for earthing as required complete in all respect as per satisfaction of Engineer-in-charge. a)2x1.5 Sq-mm

Wiring for circuit / sub-main with 4x16 Sqmm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No. 16 Sqmm (4x16+2x16) HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete in all respect as per satisfaction of Engineer-in-charge.

Supplying & fixing metal box of following sizes (nominal size) on surface or in recess suitable for fixing phenolic laminated sheet cover in front including painting etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a). 200x150x75mm deep 8x6”

Supplying & fixing following rating Piano-type switch / socket on the existing switch box / cover including connections etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a) S.P. 5/6 amps one way switch, piano type.

b) S.P. 5/6 amps two way switch, piano type.

c) Bell push, piano type.

d) S.P. 15/16 amps one way switch, porcelain base / piano type.

e) 5 pin 5/6 amps socket outlet, porcelain base / piano type.

f) 6 pin 15/16 amps socket outlet, porcelain base / piano type.

Supplying and fixing metal box of 180x100x60mm deep (nominal size) on surface / recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps, piano type switch, connections, painting etc. as required complete in all respect as per satisfaction of Engineer-in-charge.

Supplying & fixing akelite batten / angle holder including connections etc. as required complete in all respect as per satisfaction of Engineer-in-charge.

Supplying and fixing call bell / buzzer, suitable for D.C. / A.C. single phase, 230 volts complete as required complete in all respect as per satisfaction of Engineer-in-charge.

Supplying and erection of wall mounted metal boards for switch gear mounting of suitable size, with permissible variation in size of plus minus 5mm, welded frame work make of M.S. angle iron 50mm x 50mm x 6mm thick duly welded complete with 3mm thick M.S. sheet fixed with hinges as open able front, complete with locking arrangement including painting and bonding to the existing earth as required complete in all respect as per satisfaction of Engineer-in-charge.

Providing & fixing TP&N switch disconnector fuse unit cubical type, 415/500 volts with 3 Nos. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a).200 amps. Category – A.

Supplying and fixing copper strip bus-bar suitable for 200 Amp. 415 volts capacity four nos. each of cross sectional area (25.4mm x 4.75mm) in the existing enclosure with all accessories including all connection etc. as required complete in all respect as per satisfaction of Engineer-in-charge.

Supplying & erection of 6 amps. To 32 amps. Rating, 10KA breaking capacity, 240 volts, ‘C’ curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a) Single pole. Category – A

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a).100 Amps. Cat-A.

Supplying and erection of 40/50/63 amps rating, 10KA breaking capacity, 240 volts, ‘C’ curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a). Double pole. Cat. A

Supplying and fixing following rating, four pole (three phase & neutral) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 millampers in the existing MCB DB complete with connections, testing and commissioning etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a) 63 Amps. Cat-A.

Supplying and fixing following rating, double pole (single phase & neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 millampers in the existing MCB DB complete with connections, testing and commissioning etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a) 63 Amps. Cat-A.

Supplying and fixing of following way triple pole and neutral sheet steel MCB distribution board, 415 volts, on surface / recess, with provision for 4-pole MCB / isolator / RCCB / RCBO as incomer and SP MCBs as outgoing, complete with tinned copper bus-bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a).Single door-8 way (8+24), horizontal type.

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus-bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a).Single door-12 way.

Earthing with copper earth plate 600mm x 600mm x 3mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and water pipe etc. (but without charcoal or coke and salt) complete as required complete in all respect as per satisfaction of Engineer-in-charge.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required complete in all respect as per satisfaction of Engineer-in-charge.

Supplying and laying 8 SWG copper wire at 0.50 Rmt. below ground level for earth electrode conductor, including soldering etc. as required complete in all respect as per satisfaction of Engineer-in-charge.

Providing, Installation, testing & commissioning of ceiling fan without regulator, including wiring the down rods of standard length (upto 30 cm) with 16/0.20mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a).Ceiling fan 1200mm sweep, category – A.

Supplying and fixing five stepped socket type fan regulator on the existing board / box including making connections etc. as required complete in all respect as per satisfaction of Engineer-in-charge.

Providing & installation of exhaust fan with louvers of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a).Exhaust fan, Heavy duty, 300mm sweep.

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured / XLPE power cable, working voltage 1100 volts grade direct in ground to be laid one meter below the ground level including excavation and refilling the trench etc. of the required, but excluding sand cushioning and protective covering, complete in all respect as per satisfaction of Engineer-in-charge. a).Armoured cable 70 Sqmm (3.5 core).

Supplying and erection of street light bracket made of GI pipe ‘A’ class of suitable length and dia, the pipe bended to give an angle of 100 to 110 degree fitted with bolt and nuts at the top of existing pole or wall including painting the pipe with two coats of approved paint over priming coat complete in all respect as per satisfaction of Engineer-in-charge. a). 40mm dia. G.I. pipe, heavy duty.

Supplying and erection of Baton integrated LED channel integral sleek extruded polycarbonate LED channel with white acrylic cover of BCLSB 18 WH including making all necessary connection etc. as required complete in all respect as per satisfaction of Engineer-in-charge (Bajaj make).

Supplying & erection of Sky light surface mounting 2x2 luminaire white powder coated CRCA housing with high power LED’s Aluminium front frame with flat white high transmission acrylic cover of BCTBLS 36 ZT WH including making all necessary connections etc. as required complete in all respect as per satisfaction of Engineer-in-charge (Bajaj make).

Supplying & erection of Edge series of LED street light fitting with bulb (BRTFG 45w LED) with pressure die cast aluminium housing LED street light luminaries with IP66 protection and making the necessary connections etc. as required complete in all respect as per satisfaction of Engineer-in-charge (Bajaj make).