15th Finance Commission _Tied Grant 1st Installment 2023-2024-Toilet Work

Amount

Dismantling the Existing damaged RCC Roof Etc…

Earthwork excavation for foundation in all soils and sub soils in hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders and to full depth as may be directed,except in hard rock,requiring blasting including shoring and shuttering and bailing out of water wherever necessary,refilling the sides of foundation with excavated earth or sand in layer of not more than 15cm thick.well rammed and consolidated and depositing on bank with initial lead and lift of 10m & initial lift of 2m and depositing the surplusr earth within the compound in places shown by the departmental officers with iniital lead and lifts,clearing and levelling the site etc., complete as per SS20B and as directed by departmental Engineers(TNBP No.17,23,24).

Plain Cement Concrete 1:4:8 Mix (one part cement, four part sand and Eight part of aggrigate) using 40 mm size ISS HBG metal from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing. Laying and curing etc., complete

Brick work in following Cement Mortar using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:3 (One cement and three sand), 10mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Floor Finishing First Quality Design Ceramic tiles of All colours of sizes 305mm x 305mm x 6mm. laid in cm 1:3 mix 10mm thick and pointing with white cement using 0.4kg/sqm including finishing the joint and pointing flush with tiles surface etc complete

Supplying and erecting centering for sides and soffits including supports and strutting uptp 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90cmx60cm and 10 gauge stiffened, welded with mild steel angles of size 25mmx25x3mm for boarding laid over silver oak (country wood) joist of size 10cmx6.5cm dia spaced about 90cm centre to centre and supported by casuarina props of 10cm to 13cm dia spaced at 75cm centre tocentre etc.complete complying with standard specification and as directed by the departmental engineers. TNBP No.30

Supplying and fabrication of steel and placing in position of TMT steel rods for RCC works as per design given including cost of steel and GI binding wire in all floors etc., complete complying with standard specification in TNDSS NO:97 V,VI (S6) VII (S6), VII-3.

Reinforcement Cement Concrete 1:1.5:3 mix (One part of Cement, One And half part of Fine Aggregate and Three part of Coarse Aggregate) Using 20mm ISS HBG metal for foundation and basement including dewatering if found necessary and laid in layer of not more than 15cm thick and consolidated including all cost conveyance of materials and labour charges etc. complete as per standard specifications and as directed by departmental Engineers(TNBP No.28).

Supplying and fabrication and fixing in position of anodised natural colour matt fininsh sliding Door in TWO track in all floors with following sizes. All the two shutters with slinging entering and made with UPVC (ultra Polyvinyl Chloride ) section for outer frames as shown below with necessary accessories such rubber beading.clips, handle and fixing 5 mm thick clear sheet glass including all required for fabrication etc., complete. Necessary dismantling making holes in RCC columns, beams, mansory wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the dePart ofmental officers. (All materials should be got approved by the Executive Engineer before fixing in position)

Supply and fixing in position best quality of approved make Indian Water closet of size 580 x 440 mm with all accessories such as P' trap or S trap confirming to IS 2556 part XII with sand cushion and forming flooring alround the closet using 40 mm leveling course 1:4:8 -100 mm thick and finishing the top to the required slope and including necessary internal connection and outlet connection and making the disturbed potion to original condition without leakage etc., including Labour charges for fixing etc., (Colour)

Supplying and fixing in position colour glazed EUROPEAN WATER CLOSET with 'P' or 'S' trap and double flapped seat cover, 10.00 litres capacity P.V.C. low level FLUSHING TANK including all internal fittings fixed on C.I. brackets, 12mm PVC or brass nipple, chromium plated brown headed stopcock, 12mm nylon connection with necessary teakwood plugs, clamps, screws to the portion coming with walls and floors, including dismantling masonry and redoing the same to the original condition.

Supplying and fixing of Mild steel door including cost and conveyance charges to site fixing in its position and all labour charges etc complete.

Daddoing with first quality colour glazed tiles of 150 mm x 150 mm x 6mm size of approved make and quality and colour set in Cement Mortar 1:2 (One Cement and Two Sand) and pointing with white cement neatly including cost and conveyance of all materials etc.and all lobour charges etc.complete as per Standard specification and as directed by the departmental officers.TNBP No:special

Finishing the top of roof with one course of machine pressed tiles of size 20cm x 20cm x 2 cm approved quality laid in cement mortar 1:3 (One cement and three sand) 12mm thick mixed with water proofing compound confirming to ISS by 2% weight of Cement used and the joint pointed neatly to full depth of tiles with the same water proofing compound mixed with cement mortar, red oxide etc., complete complying with standard specifications.

Painting two coats with ready mixed Emulsion of first class quality paint and of approved color over a priming coat, including through scrapping, clean removal of dirt, etc., complete.

Painting new iron work with two coats of best first quality synthetic enamel paint of approved colour over the existing red oxide primer coat as directed by departmental officers complete complying with standard specification.

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC.unsheathed Cu. Conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A F.T. switch with painting of suitable Colourfor open PVC light point / fan point (For electronic regulator) (5 points per coil)SD 18

Supply and fixing 12 Watts LED Light With Fittings etc Complete.

Supply and fixing of 25 Watts LED Street light Fittings with LED Light etc Compelte

Arun Krishna Prasath