Construction of New High Court at Rakh-i-Gund Aksha,Bemina Srinagar by way of Electrical and allied work Phase-I

Supplying Installation testing and Commissioning of 32 Port Fiber Switch 10/100/1000BASE-T ports, with up to 4X 10GbE uplinks and 2X 40GbE uplinks, Switch should support stacking bandwidth of minimum 160gbps, Modular operating system, 32 1 Gig SFP port with additional 4 no. of 10g SFP+PORT, redundant power supply, layer3 switch, each switch should be provided with stacking port/cable complete in all respect. Approved Make-Juniper/Cisco/Extreme

Supply & Fixing of OM3 50/125μ Type Pigtails of ISO/IEC-11801-OM3 Pigtails with LC Type Connectors,pigtails for terminating fibers on the FOPP complete in all respect.Make-Legrand/Siemon/Panduit

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable having IS 694:2010 ROHS ,BIS ,ISO Compilance & copper purity 99.97% Electrolytic ,Voltage rating 1100 V (1.1KV) ,Temperature rating upto 85 Deg C of Polycab (green) /Finolex /Havels (Life guard) /RR Cables / Anchor (HFFR) /Salzar make to be laid in surface / recessed PVC conduit (Minimum 25 mm dia HMS PVC conduits with allied accessories incutting cutting of walls /floors and resurfacing to original position after laying of conduits preferably Finolex /Ravendra greeen / Polpack / Paraflex /Anchor make complete job including cost of conduits and allied accessories as per site requirement and as per instructions of EIC ) , and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials

Wiring for light/ power plug with 3 X4 sq. mm FRLS PVC insulated copper conductor single core cable having IS 694:2010 ROHS ,BIS ,ISO Compilance & copper purity 99.97% Electrolytic ,Voltage rating 1100 V (1.1KV) ,Temperature rating upto 85 Deg C of Polycab (green) /Finolex /Havels (Life guard) /RR Cables / Anchor (HFFR) /Salzar make to be laid in surface / recessed PVC conduit (Minimum 25 mm dia HMS PVC conduits with allied accessories incutting cutting of walls /floors and resurfacing to original position after laying of conduits preferably Finolex /Ravendra greeen / Polpack / Paraflex /Anchor make complete job including cost of conduits and allied accessories as per site requirement and as per instructions of EIC ) The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates and samples for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable having IS 694:2010 ROHS ,BIS ,ISO Compilance & copper purity 99.97% Electrolytic ,Voltage rating 1100 V (1.1KV) ,Temperature rating upto 85 Deg C of Polycab (green) /Finolex /Havels (Life guard) /RR Cables / Anchor (HFFR) /Salzar make to be laid in surface / recessed PVC conduit (Minimum 25 mm dia upto 4 Sq.mm , 32 mm dai from 6 Sq.mm to 10 Sq.mm and 38 mm dia above 10 Sq.mm , HMS PVC conduits with allied accessories incutting cutting of walls /floors and resurfacing to original position after laying of conduits preferably Finolex /Ravendra greeen / Polpack / Paraflex /Anchor make complete job including cost of conduits and allied accessories as per site requirement and as per instructions of EIC ). The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates along with samples for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire for circuit wiring

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire for light plug

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 10 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable of Polycab (green) /Finolex /Havels (Life guard) /RR Cables / Anchor (HFFR) /Salzar make in the existing surface/ recessed PVC conduit as required. The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials

6 x 1.5 sq. mm

9 x 1.5 sq. mm

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings) of Havells Crabtree Signia Grand Series (glass finish) /Legrend Arteor Series / L&T Englaze Series (glass finish) / ABB Zenit (glass finish) Series / Siemens Delixi / Schneider Electric Exxact Series.(The Sample must be approved from departmental officer not below the rank of SDO before despatching /Installation of switches-sockets at the work site)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.of of Havells Crabtree Signia Grand Series (glass finish) /Legrend Arteor Series / L&T Englaze Series (glass finish) / ABB Zenit (glass finish) Series / Siemens Delixi / Schneider Electric Exxact Series. (The Sample must be approved from departmental officer not below the rank of SDO before despatching /Installation of switches-sockets at the work site)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 Nos. 3 pin 5/6 amps modular socket outlet and 2 No. of 6 amps modular switch, connection etc. as required. ( UPS Points ).of of Havells Crabtree Signia Grand Series (glass finish) /Legrend Arteor Series / L&T Englaze Series (glass finish) / ABB Zenit (glass finish) Series / Siemens Delixi / Schneider Electric Exxact Series . (The Sample must be approved from departmental officer not below the rank of SDO before despatching /Installation of switches-sockets at the work site)

Supplying and fixing 32 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required

Supplying and fixing modular type call bell/ buzzer with LED indication, suitable for single phase, 230 volts, complete as required.

Supplying and fixing of following sizes of PVC conduit (HMS Model ) along with accessories in recessed including cutting of walls with hydraulic cutter &refacing of walls complete with painting making good the same in case of recessed conduit as required.

SUB HEAD - II - DISTRIBUTION BOARD

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) of Commercial series of Legrend /L&T /ABB /Scheinder /Simens make The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials

4 way (4 +12), Double door

6 way (4 +18), Double door

8 way (4 + 24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.of Commercial series of Legrend /L&T /ABB /Scheinder /Simens make The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials

12 way (4+36), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) of Commercial series of Legrend /L&T /ABB /Scheinder /Simens make The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials

2 + 12 way, Double door

2 + 8 way, Double door

Supplying and fixing following rating, four pole, 415 V, TPN MCB (10KA) ''C Curve " in the existing MCB DB complete with connections, testing and commissioning etc. as required. of Legrend (DX3 Series) /L&T (L-Square series) /ABB (S 500 series) /Simens (3VL Series ) / Schneider (Acti-09 series)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milli amperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. of Legrend (DX3 Series) /L&T (L-Square series) /ABB (S 500 series) /Simens (3VL Series ) / Schneider (Acti-09 series). The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required of Legrend (DX3 Series) /L&T (L-Square series) /ABB (S 500 series) /Simens (3VL Series ) / Schneider (Acti-09 series) The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials

Single pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

SUB HEAD-III RACEWAYS

Supply, assembly and laying of under floor trunking made out of 1.6mm thick GI sheet complete with jointing sleeve, horizontal bends, floor junction box, vertical bends, level adjustment components and closer, vertical elbow, covers, access outlet. etc. complete with all other accessories under floor installation including cutting and chasing the floor/ or on surface, making good the same, placing in position and cleaning from inside complete etc. as required. of Legrend / Honeywell /MK Electric /United U-LI /OBO Bettermann / Schneider Electric /Hellermann Tyton / Niedax Group make The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials

250 mm x 38 mm (3 compartment)

150 mm x 38 mm (2 compartment)

100 mm x 38 mm (2 compartment)

50 mm x 38 mm (1 compartment)

Supplying Installation testing and Commissioning of Small Form Factor Pluggable 10 Gigabit Ethernet (SFP+) SR Optics . Make-Juniper/Cisco/Extreme

Supply Installation, testing and commissioning of following fittings/ luminaires/ ceiling fans complete with necessary starter/s & copper wound/ electronic ballasts, capacitors, lamps, louvers & all other accessories, down rods of suitable length, connections with 1.5 sq.mm. PVC insulated FRLS, copper conductor, single core cable including loop earthing with 1.5 sq mm FRLS PVC insulated copper conductor, single core cable etc. complete as required.

Supply, Installation, testing & commissioning of IP20 Recessed LED Downlighter made of pressure die cast aluminum housing. The front cover of the luminaire shall be made of polystyrene/polycarbonate/PMMA. Fixture should have minimum efficacy at System level (Not Chip Level) ≥140 lumens/watt & Minimum system Lumen output of 1200lm. The downlighter shall be mandatorily back-lit & not side-lit. LED used shall have life of 50000Hrs @ L70B50, CCT of 6500°K, SDCM≤5 & CRI≥80. The LEDs used shall be SMD type only & should be from Philips/Signify/APT Electronics/Osram/Nichia/Cree/Lumileds /Bridgelux. The LED luminaire driver shall be DALI 2.0 compliant driver & shall have rated voltage as 220V to 240V. The driver efficiency shall be ≥85%. The driver should have following compliances iTHD≤ 20% (@full load), PF≥ 0.90 (@full load), output current ripple ≤ 5%, in-built surge protection of 2KV & Life of 50000hrs. The driver should be suitable for ambient temperature of -20°C to +50°C. The driver should have open load protection, short circuit protection and over power protection. The driver shall be SELV. The driver should be able to dim form 1% to 100%. The driver should be CE marked. The driver should be in plastic/metal casing. The fixture should comply with the parameters as per IS10322. The luminaire shall have class B serviceability. The luminaire height shall be 40MM, with minimum & m cut-out dia of 150mm & the width of the lip shall be minimum 8mm. The luminaire shall be IK02 compliant. The luminaire brand name shall be embossed/engraved/Screen printed on the lumi

naire/accessory/Endplate/Rim/Frame & not put using sticker. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79 as per 2019 standard, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79 as per 2019 standard, Type Test report for luminaire, EMI compliance test report, surge protection test report & current ripple test report. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire & Driver. Approved makes Signify (Philips)/ Igguzini/Lighting Techonology /Endo / Regent /Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out

Supply, Installation, testing & commissioning of IP20 Recessed LED Downlighter made of pressure die cast aluminum housing. The front cover of the luminaire shall be made of polystyrene/polycarbonate/PMMA. Fixture should have minimum efficacy at System level (Not Chip Level) ≥140 lumens/watt & Minimum system Lumen output of 1500lm. The downlighter shall be mandatorily back-lit & not side-lit. LED used shall have life of 50000Hrs @ L70B50, CCT of 6500°K, SDCM≤5 & CRI≥80. The LEDs used shall be SMD type only & should be from Philips/Signify/APT Electronics/Osram/Nichia/Cree/Lumileds /Bridgelux. The LED luminaire driver shall be DALI 2.0 compliant driver & shall have rated voltage as 220V to 240V. The driver efficiency shall be ≥85%. The driver should have following compliances iTHD≤ 20% (@full load), PF≥ 0.90 (@full load), output current ripple ≤ 5%, in-built surge protection of 2KV & Life of 50000hrs. The driver should be suitable for ambient temperature of -20°C to +50°C. The driver should have open load protection, short circuit protection and over power protection. The driver shall be SELV. The driver should be able to dim form 1% to 100%. The driver should be CE marked. The driver should be in plastic/metal casing. The fixture should comply with the parameters as per IS10322. The luminaire shall have class B serviceability. The luminaire height shall be 40MM, with minimum & m cut-out dia of 150mm & the width of the lip shall be minimum 8mm. The luminaire shall be IK02 compliant. The luminaire brand name shall be embossed/engraved/Screen printed on the luminaire/accessory/Endplate/Rim/Frame & not put using sticker. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79 as per 2019 standard, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79 as per 2019 standard, Type Test report for luminaire, EMI compliance test report, surge protection test report & current ripple test report. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire & Driver. Approved makes Signify (Philips) / Igguzini /Lighting Techonology /Endo / Regent / Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite

certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out

Supply, Installation, testing & commissioning of IP20/IK02 Deep Recessed LED Downlighter made of pressure die cast aluminum housing. The front cover below the LEDs shall be made of polystyrene/polycarbonate/PMMA. The luminaire shall have Aluminimum finished reflector made pf PC/PS/Engineering plastic & shall comply to UGR<19 rating. Fixture should have minimum efficacy at System level (Not Chip Level) ≥130 lumens/watt & Minimum system Lumen output of 3150lm. The downlighter shall be mandatorily back-lit & not side-lit. LED used shall have life of 50000Hrs @ L70B50, CCT of 5700°K, SDCM≤5 & CRI≥80. The LEDs used shall be SMD type only & should be from Philips/Signify/APT Electronics/Osram/Nichia/Cree/Lumileds /Bridgelux/.The LED luminaire driver shall be DALI 2.0 compliant driver & shall have rated voltage as 220V to 240V. The driver efficiency shall be ≥85%. The driver should have following compliances iTHD≤ 20% (@full load), PF≥ 0.90 (@full load), output current ripple ≤ 5%, in-built surge protection of 2KV & Life of 50000hrs. The driver should be suitable for ambient temperature of -20°C to +50°C. The driver should have open load protection, short circuit protection and over power protection. The driver shall be SELV. The driver should be able to dim form 1% to 100%. The driver should be CE marked. The driver should be in plastic/metal casing. The fixture should comply with the parameters as per IS10322. The luminaire shall have class B serviceability. The luminaire height shall be minimum 105MM, with cut-out dia of 200mm & the width of the lip shall be minimum 8mm. The luminaire shall be IK02 compliant. The luminaire brand name shall be embossed/engraved/Screen Printed on the luminaire /accessory/ Endplate/ Rim/ Frame & not put using sticker. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79 as per 2019 standard, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79 as per 2019 standard, Type Test report for luminaire, EMI compliance test report, surge protection test report & current ripple test report. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire & Driver.Approved makes Signify (Philips) / Igguzini / Lighting Techonology / Endo / Regent / Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out

Supply, Installation, testing & commissioning of IP20/IK02 surface mounted downlighter having housing made of CRCA only. The front cover below the LEDs shall be made of polystyrene/polycarbonate/PMMA. Fixture should have minimum efficacy at System level (Not Chip Level) ≥100 lumens/watt & Minimum system Lumen output of 1500lm. The downlighter shall be mandatorily back-lit & not side-lit. LED used shall have life of 50000Hrs @ L70B50, CCT of 5700°K, SDCM≤5 & CRI≥80. The LEDs used should be from Philips/Signify/APT Electronics/Osram/Nichia/Cree/Lumileds /Bridgelux/Citzen. The luminaire shall use electronic driver having PF≥0.90

(@full load), iTHD ≤ 10% (@full load) in-built surge protection of 4KV (both in CM & DM). The operating voltage range shall be 160V to 270V. The fixture should comply with the parameters as per IS10322. The luminaire shall have class B serviceability. The luminaire height shall be between 36MM to 38MM with minimum dia of 177MM. The luminaire brand name shall be embossed/engraved/Screen Printed on the luminaire/accessory/Endplate/Rim/Frame & not put using sticker. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79 as per 2019 standard, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire should be BIS registered. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79 as per 2019 standard, Type Test report for luminaire, surge protection test report & current ripple test report. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire. Approved makes Signify (Philips) /Endo/ Igguzini/Lighting Techonology / Regent /Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials

SITC of 2ft Integral LED batten having housing made of CRCA only with PC/PS diffuser (Diffuser-Non yellowing type). The luminaire end caps shall be made of PC/PS/ABS Plastc. Luminaire shall be designed to emit at least minimum 2000 system lumens at a system efficacy of ≥ 120 lumen/watt. LED used shall have life of 50000Hrs @ L70B50, CCT of 5700°K, SDCM≤5 & CRI≥80. The LEDs used should be from Philips/Signify/APT Electronics/Osram/Nichia/Cree/Lumileds /Bridgelux/Citzen. The electronic driver used shall have a power factor ≥0.90 and THD ≤10%, suitable for an operating voltage range of 140-270V AC, Current Ripple ≤5%, Internal surge protection should be minimum 4KV, electrical insulation class should be Class I & driver should be of Class B serviceability. The luminaire shall be IP20 & IK02 compliant. The minimum dimensions (±5mm) of the batten shall be 44mm(±5mm) X 51mm (±5mm)X 585mm(±5mm). The luminaire brand name shall be embossed/engraved/Screen Printed on the luminaire/accessory/Endplate/Rim/Frame & not put using sticker. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79 as per 2019 standard, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79 as per 2019 standard, Type Test report for luminaire, surge protection test report & current ripple test report. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire & Driver. Approved makes Signify (Philips)/ Igguzini/Lighting Techonology /Endo / Regent /Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out

SITC of Integral LED 4ft luminaire with PIR Sensor & housing made of of CRCA only and Polycarbonate/Polystyrene diffuser (Diffuser-Non yellowing type). The minimum dimensions (±5mm)

of the batten shall be 44mm(±5mm) X 51mm (±5mm) X 1221mm(±5mm). The LEDs used shall have CCT of 6500°K (±350°K), CRI ≥ 80, SDCM ≤ 5 & life of 50000Hrs @ L70B50. The luminaire shall deliver initial system lumen output of 2000lm with minimum system efficacy of 120lm/w. The luminaire shall have operating temp -10°C to 45°C. The driver of the LED downlighter shall have minimum operating voltage of 120V to 270V, PF≥0.95 & In-built surge protection of ≥4KV, THD≤10%, Driver efficiency of ≥ 85%. The driver shall be compliant to IEC62384, CISPR15/EN55015 (9KHz to 30MHz), IEC61347-2-13, IEC61547 & IEC6100-3-2. The driver & Luminaire shall be BIS registered. The driver shall be designed for continuous operation of minimum 12-15Hrs a day. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. The PIR sensor should be able to dim the fixture to 50% in case of no movement. Sensor should have a detection angle of 60 degree and luminaire should be at least IP20 & IK02 rated. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab in India to conduct LM79, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of LED Luminaires for approval.The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of LED Luminaires for approval. Successful bidder shall submit the following reports before supply of material for approvals LM79 issued by NABL accredited lab, LM80 issued by LED manufacturer, Type Test Certificate for luminaire as issued by NABL accredited lab, IK Test Report issued by NABL accredited lab & BIS certificate for LED Luminaire.. Approved makes Signify (Philips)/ Igguzini/Lighting Techonology /Endo / Regent /Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out.

SITC of circular LED High Bay having housing made of pressure die cast aluminum. The luminaire shall deliver minimum 20000Lumens with minimum system efficacy of 170lm/w. The luminaire shall be IP65 & IK08. The font cover of the luminaire shall be integrated PC lens plate ensuring IP65 rating. The luminaire shall be design for life of 100000Hrs, L70 @ 45°C. The luminaire shall have class B serviceability & shall have Cass I insulation. The luminaire shall use DALI 2.0 enabled driver having PF≥0.90, THD ≤20 (@full load)Current Ripple of ≤10%, over voltage protection, under voltage protection, open ceircuit protection. The luminaire brand name shall be embossed/engraved/Screen printed on the Luminaire /accessory/ Endplate/ Rim/ Frame & not put using sticker. The luminaire driver shall be of the same make /manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79 as per 2019 standard, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire should be BIS registered (if applicable). Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79 as per 2019 standard, Type Test report for luminaire, EMI Compliance report, surge protection test report. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire & Driver. Approved makes Signify (Philips)/ Igguzini/Lighting Techonology /Endo / Regent /Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) on O

EM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out.

SITC of LED Recessed Downlighter having cut-out dia of 125mm(± 3mm) & lip to lip dia of 137mm (± 3mm) delivering minimum system lumen output of 1200 lumens and minimum system efficacy of 120lm/w. The luminaire should have deep recessed COB light source & the luminaire shall have UGR≤19 & Shielding Angle of 38°. The luminaire shall have the beam angle of 60° to 65°. The downlighter shall be mandatorily back-lit & not side-lit. LED used shall have life of 50000Hrs @ L70B50, CCT of 6500°K, SDCM≤5 & CRI≥80, R≥9. The LEDs used should be from Philips/Signify/APT Electronics/Osram/Nichia/Cree/Lumileds /Bridgelux/Citzen. The LED luminaire driver shall be DALI 2.0 compliant driver & shall have rated voltage as 220V to 240V. The driver efficiency shall be ≥85%. The driver should have following compliances iTHD≤ 20% (@full load), PF≥ 0.90 (@full load), output current ripple ≤ 5%, in-built surge protection of 2KV & Life of 50000hrs. The driver should be suitable for ambient temperature of -20°C to +50°C. The driver should have open load protection, short circuit protection and over power protection. The driver shall be SELV. The driver should be able to dim form 1% to 100%. The driver should be CE marked. The driver should be in plastic/metal casing. The luminaire housing, heat sink & ring should made of pressure die-cast aluminum. The luminaire should have faceted reflector made of Spun Aluminum. Reflectors made of Polycarbonate shall not be allowed. The fixture should comply with the parameters as per IS10322. The luminaire shall have impact resistance of IK02 & ingress protection of IP20. The luminaire brand name shall be embossed/engraved/Screen Printed on the luminaire/accessory/Endplate/Rim/Frame & not put using sticker. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79 as per 2019 standard, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79 as per 2019 standard, Type Test report for luminaire, EMI compliance test report, surge protection test report & current ripple test report. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire & Driver.Approved makes Signify (Philips)/ Igguzini/Lighting Techonology /Endo / Regent /Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out

Supply, Installation, testing & commissioning of IP20/IK02 Deep Recessed LED Downlighter made of pressure die cast aluminum housing. The front cover below the LEDs shall be made of polystyrene/polycarbonate/PMMA. The luminaire shall have Aluminimum finished reflector made pf PC/PS/Engineering plastic & shall comply to UGR<19 rating. Fixture should have minimum efficacy at System level (Not Chip Level) ≥130 lumens/watt & Minimum system Lumen output of 3150lm. The downlighter shall be mandatorily back-lit & not side-lit. LED used shall have life of 50000Hrs @ L70B50, CCT of 5700°K, SDCM≤5 & CRI≥80. The LEDs used shall be SMD typ

e only & should be from Philips/Signify/APT Electronics/Osram/Nichia/Cree/Lumileds /Bridgelux/.The LED luminaire driver shall be DALI 2.0 compliant driver & shall have rated voltage as 220V to 240V. The driver efficiency shall be ≥85%. The driver should have following compliances iTHD≤ 20% (@full load), PF≥ 0.90 (@full load), output current ripple ≤ 5%, in-built surge protection of 2KV & Life of 50000hrs. The driver should be suitable for ambient temperature of -20°C to +50°C. The driver should have open load protection, short circuit protection and over power protection. The driver shall be SELV. The driver should be able to dim form 1% to 100%. The driver should be CE marked. The driver should be in plastic/metal casing. The fixture should comply with the parameters as per IS10322. The luminaire shall have class B serviceability. The luminaire height shall be minimum 105MM, with cut-out dia of 200mm & the width of the lip shall be minimum 8mm. The luminaire shall be IK02 compliant. The luminaire brand name shall be embossed/engraved/Screen Printed on the luminaire/accessory /Endplate /Rim / Frame & not put using sticker. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79 as per 2019 standard, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79 as per 2019 standard, Type Test report for luminaire, EMI compliance test report, surge protection test report & current ripple test report. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire & Driver. Approved makes Signify (Philips) /Endo/ Igguzini/Lighting Techonology / Regent /Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials

SITC of 4ft Surface/Suspended Integral LED luminaire having housing made of CRCA only with PC/PS diffuser (Diffuser-Non yellowing type). The luminaire end caps shall be made of PC/PS/ABS Plastc. Luminaire shall be designed to emit at least minimum 3900 system lumens at a system efficacy of ≥ 130 lumen/watt. LED used shall have life of 50000Hrs @ L70B50, CCT of 5700°K, SDCM≤5 & CRI≥80. The LEDs used should be from Philips/Signify/APT Electronics/Osram/Nichia/Cree/Lumileds /Bridgelux/Citzen. The electronic driver used shall have a power factor ≥0.90 and THD ≤10%, suitable for an operating voltage range of 140-270V AC, Current Ripple ≤5%, Internal surge protection should be minimum 4KV, electrical insulation class should be Class I & driver should be of Class B serviceability. The luminaire shall be IP20 & IK02 compliant. The minimum dimensions (±5mm) of the batten shall be 44mm(±5mm) X 51mm (±5mm)X 1157mm(±5mm). The luminaire brand name shall be embossed/engraved/Screen Printed on the luminaire/accessory/Endplate/Rim/Frame & not put using sticker. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79 as per 2019 standard, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79 as per 2019 standard, Type Test report for luminaire, surge protection test report & current ripple test report. The bidder shall also submit the LM80 report issued by LED manufacturer, B

IS certificate for LED Luminaire & Driver. Approved makes Signify (Philips)/ Igguzini/Lighting Techonology /Endo / Regent /Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out

SITC of 2ftX2ft recessed mounted luminaire having housing made of deep drawn CRCA only with PC/PS diffuser (Diffuser-Non yellowing type). The housing containing the LEDs shall be single piece. Luminaire shall be designed to emit at least minimum 3600 system lumens at a system efficacy of ≥ 140 lumen/watt. The luminaire shall be mandatorily back-lit & not side-lit. LED used shall have life of 50000Hrs @ L70B50, CCT of 6500°K, SDCM≤5 & CRI≥80. The LEDs used should be from Philips/Signify/APT Electronics/Osram/Nichia/Cree/Lumileds /Bridgelux. The LED luminaire driver shall be DALI 2.0 compliant driver & shall have rated voltage as 220V to 240V. The dimming should be amplitude modulation dimming. The driver efficiency shall be ≥85%. The driver should have following compliances iTHD≤ 20% (@full load), PF≥ 0.90 (@full load), output current ripple ≤ 5%, in-built surge protection of 2KV & Life of 50000hrs. The driver should be suitable for ambient temperature of -20°C to +50°C. The driver should have open load protection, short circuit protection and over power protection. The driver should be able to dim from 1% to 100%. The driver should be CE marked. The driver should be in metal casing only. The fixture should comply with the parameters as per IS10322. The luminaire shall have class B serviceability. The luminaire shall be IK02 compliant. The luminaire brand name shall be embossed /engraved / Screen printed on the luminaire/accessory/Endplate/Rim/Frame & not put using sticker. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79 as per 2019 standard, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. The LED Luminaire & it's driver both should be BIS registered. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79 as per 2019 standard, Type Test report for luminaire, EMI compliance test report, surge protection test report & current ripple test report. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire & Driver.Approved makes Signify (Philips)/ Igguzini/Lighting Techonology /Endo / Regent /Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out

Supply of LED Strip light with Aluminium extruded Channel With lumen package of 1200lm/Mtr,IP20,CCT-3000k,Seperate LED Driver.Approved makes Signify (Philips)/ Igguzini/Lighting Techonology /Endo / Regent /Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out

SITC of 2.5W to 4W recessed Step light delivering system lumen output of 50 lumens in 4000°K CCT. The luminaire shall be IP67/IK08 compliant with housing made of pressure die cast aluminium, diffused optical cover made of PC & plastic mounting box. The luminaire shall be suitable for operating temperature of -20°C to 40°C. The luminaire life shall be 25000 Hrs @ L70B50. The end to end external dimension of the step light shall be 145MM X 145Mm with total dept of 104MM with plastic mounting box. The luminaire shall have class I Insulation. The luminaire brand name shall be embossed /engraved / Screen printed on the luminaire /accessory /Endplate /Rim /Frame & not put using sticker. The

luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79 as per 2019 standard, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79 as per 2019 standard, Type Test report for luminaire. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire (if applicable).Approved makes Signify (Philips)/ Igguzini/Lighting Techonology /Endo / Regent /Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out

SITC of 2.5W to 4W recessed Step light delivering system lumen output of 50 lumens in 4000°K CCT. The luminaire shall be IP67/IK08 compliant with housing made of pressure die cast aluminium, diffused optical cover made of PC & plastic mounting box. The luminaire shall be suitable for operating temperature of -20°C to 40°C. The luminaire life shall be 25000 Hrs @ L70B50. The end to end external dimension of the step light shall be 145MM X 145Mm with total dept of 104MM with plastic mounting box. The luminaire shall have class I Insulation. The luminaire brand name shall be embossed /engraved / Screen printed on the luminaire/accessory/Endplate/Rim/Frame & not put using sticker. The luminaire driver shall be of the same make/manufacturer as that of LED luminaires. Luminaire manufacturer must have In-house NABL accredited lab to conduct LM79 as per 2019 standard, Type test as per IS10322, "FAT" before dispatch as per IS 10322 & IK Test. The successful bidder must submit the NABL accreditation certificate for Luminaire manufacturer before supply of material. Successful bidder shall submit the following reports issued by NABL accredited lab before supply of material for approvals: LM79 as per 2019 standard, Type Test report for luminaire. The bidder shall also submit the LM80 report issued by LED manufacturer, BIS certificate for LED Luminaire (if applicable).Approved makes Signify (Philips)/ Igguzini/Lighting Techonology /Endo / Regent /Trilux make. The Agency / firm must submit the Techanical data sheet (TDS) on OEM letter head along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials. The Job includes 2-years replacement warrenty for the entire lighting fixtures from the the date of sucessful handing over of site to intending department , covering any damage /mulfunctioning /burnt out

Supply, Installation, testing and commissioning of 5 star rateing 1200mm ceiling fans complete with double ball bearing, motor, blades, canopies, capacitor etc. suitable for operation on 230 volts, 50 Hz., 1 phase, AC supply complete as required. ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.of Crompton /Usha /Orient / Helonix /Eq makes to be approved from department

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required

Supplying, Installation, testing and commissioning of 450 mm dia wall bracket fan complete in all respect as required.

SUB HEAD - V - LIGHTING CONTROL SYSTEM.

SITC of System Manager Visualization Software tool to Control, Monitor & Maintain. It provides users with full visibility of the lighting and energy management system status and performance, while enabling simple local or global system adjustments. Software Functions: Complete Control, Simple Scheduling, Manage routine maintainence, strike the balance, identity energy savings initiatives based on the current usage, tailored control for individual light fitting. The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials .The Job includes CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective / mulfunctioning by fresh one during CMC Period. approved makes /specifictaions in Signify (Philips Dynalite) / Creston / Kramer.

Supply of 3 Channel DALI high frequency ballasts controller for T4/Flouroscent/ LED lamps with 3 no's of 20A Relay. Each DALI outputs allowing it to control up to 192 DALI devices with 3 channels. The DALI control signals can be programmed to operate automatically isolate the power circuit when all associated DALI channels are at 0%. The device is DIN-rail mountable integral DALI bus power supply, removing the need for an additional external device. Supply: 100-240V 50/60Hz Single Phase at 0.1A, Control Outputs: 3 x DALI Control Outputs, each supporting a full DALI universe of 192 channels including backward channel DALI Bus Power Supply, Internal 24V rated 250mA Control IO :1 x RS485 DyNet serial port / DMX, 1 x AUX programmable dry contact input. DC supply 12V @ 200 mA. The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates for approval from the department not below the rank of SDO ,prior to the supply of materials .The Job includes CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective /mulfunctioning by fresh one during CMC Period. approved make: Signify (Philips Dynalite)/Creston/Kramer.

SITC of Wall / Ceiling / Recess Mount PIR Multifunction (Motion/ Daylight/ IR) Detector, Sensor Type: Dual Element Pyroelectric, Maximum detection range: 21m (676 ft), Detection Area: 17.8m x 17.8m x 20.6 at a height of 2.5m, PE Cell Dynamic range 5- 10000 lux Automatic “Daylight Harvesting” mode Can be used for light measurement for PI

R. Supply Voltage: 12/24VDC, Supply Current: 20mA, IEC Overvoltage Cat: III, Colour: RAL 9010 (White), User Input: Infrared RC5 IR Remote Control, Red Indicator on Motion Detection, Serial Port: 1x RS485, Construction: Polycarbonate Plastic Enclosure with IP 54 Rating. Operating Temp: -20 deg C to 45 deg C ambient. Compulsory Certifications : CE, RCM, UL/cUL/ICES-003 & RoHS. The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates for approval from the department not below the rank of SDO ,prior to the supply of materials .The Job includes CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective /mulfunctioning by fresh one during CMC Period. Aproved make : Signify (Philips Dynalite)/Creston/Hubble/Honeywell.

Supply, Installation, testing & Commissioning of Digital Passive infrared (PIR) technology based occupancy sensor along with photocell operation, having high performance non regulating type, with 360 degree coverage, sensitivity options of low, high, medium and max with 10m diameter coverage area (with 7m minor and 3m major movement) having features like Power up state and setback senstivity, with operating temperature of range 0 to 40 deg C, with necessary fixing arrangements i/c programming / setting at site etc. complete as required, Certifications : CE, RCM, UL/cUL/ICES-003 & RoHS. The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates for approval from the department not below the rank of SDO ,prior to the supply of materials .The Job includes CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective /mulfunctioning by fresh one during CMC Period. approved make Signify (Philips Dynalite)/Creston/Hubble/Honeywell.

Supply of Network Gateway to provide integration between the control system and Ethernet network. The gateway shall be capable of Online/offline status reporting for connected devices, network traffic logging, secure remote firmware update and lighting control metrics. Inbuilt timeclock and schedule manager allowing the user to manage automated operations and task scheduling. The gateway shall provide multiple integration options – TCP/UDP, IPv4/IPv6, unicast/multicast/broadcast, DyNet1, DyNet2, Fidelio, BACnet, and ‘Text and Binary Integration’ protocols capable of supporting hundreds of socket connections concurrently. Certification: CE, RCM, UL/cUL, FCC, UKCA, RoHS, CAN ICES-3 (B)/NMB-3 (B). The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates for approval from the department not below the rank of SDO ,prior to the supply of materials .The Job includes CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective /mulfunctioning by fresh one during CMC Period. approved make Signify (Philips Dynalite)/Creston/Kramer.

SITC of Display keypad with Central Display to present multiple pages of functions & system Information. Keypad shall possess fully programmable options for Individual control / group control / Scene control / Tasks etc. Wall mounted on 2M (3 X 3 size) modular box. Front cover with Backlight, built in proximity and a built-in temperature sensor automatically adjusts air conditioning when integrated into the system. Loaded icons like presentation scenario, meeting scenario, master On/Off, Powersaving mode etc along with a LED indicator for each operations. Central LCD - Allows for system information to be shown such as temperature, time, channel level and current scene. Button function can change when navigating between the up to 16 pages. Operating on 12V DC @ 40-50mA from network. The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates for approval from the department not below the rank of SDO ,prior to the supply of materials .The Job includes CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective /mulfunctioning by fresh one during CMC Period. approved make Signify (Philips Dynalite)/Creston/Kramer.

SITC of Display keypad with Central Display to present multiple pages of functions & system Information. Keypad shall possess fully programmable options for Individual control / group control / Scene control / Tasks etc. Wall mounted on 2M (3 X 3 size) modular box. Front cover with Backlight, built in proximity and a built-in temperature sensor automatically adjusts air conditioning when integrated into the system. Loaded icons like presentation scenario, meeting scenario, master On/Off, Powersaving mode etc along with a LED indicator for each operations. Central LCD - Allows for system information to be shown such as temperature, time, channel level and current scene. Button function can change when navigating between the up to 16 pages. Operating on 12V DC @ 40-50mA from network. The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates for approval from the department not below the rank of SDO ,prior to the supply of materials .The Job includes CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective /mulfunctioning by fresh one during CMC Period. approved make Signify (Philips Dynalite)/Creston/Kramer.

SITC of desktop server with Microsoft Windows 2010 Server Operating S

ystem Installed. The hardware Includes the computer with a high performance hard drive for maximum data integrity, a monitor, a keyboard and a mouse.The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials .The Job includes CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective /mulfunctioning by fresh one during CMC Period

SITC of Dynet Bus wire having UTP, 4-Pair cable providing significant headroom above all ISO/IEC and ANSI/TIA Category 6 / Class E transmission performance specifications. Combining high performance category 6 connectivity DC Resistance <7.32Ω/100m,Mutual Capacitance 5.6nF/100m,Capacitance Unbalance <160 pF/100m,NVP 68%,Delay Skew ≤35ns.The cable should be able to trasmit high speed RS485 signal,it should also be capable of send and received messages over RS232 networks in case of duplex communication. The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates for approval from the department not below the rank of SDO ,prior to the supply of materials .The Job includes CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective /mulfunctioning by fresh one during CMC Period. Similar to above specifictaions in Siemon/systimax/Panduit/Nexans.

SITC of Automation dustribution panel IP 67 with inbuilt Fan for heat disspation with required protection devices. As per actual requirement. The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials .The Job includes CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective /mulfunctioning by fresh one during CMC Period

SITC of Automation dustribution panel IP 67 with inbuilt Fan for heat disspation with required protection devices. As per actual requirement.The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials.The Job includes CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective /mulfunctioning by fresh one during CMC Period

Complete commissioning of the above LMS system as described including CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective /mulfunctioning by fresh one during CMC Period. The Agency / firm must submit the Techanical data sheet (TDS) along with requisite certificates for approval by an officer from the department not below the rank of SDO ,prior to the supply of materials .The Job includes CMC (Comphrensive maintenance contract ) for a period of two years reckoned from date of sucessful handing of site to imtending .The CMC includes timely servicing and replacement of damaged /defective /mulfunctioning by fresh one during CMC Period

SUB HEAD - VI - (Bus duct / Rising mains)

Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as requiredof Commercial series of Legrend /L&T /ABB /Scheinder /Simens

800 amps 50KA SC for 1 sec

630 amps 50KA SC for 1 sec

400 amps 25KA SC for 1 sec

Supplying, installing, connecting to existing sandwhich type rising mains and testing and commissioning of following capacity Plug In/ Tap Off Box for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with 1.6mm thick steel sheet enclosure duly powder coated with provision of MCCB (but without MCCB) complete etc. as requiredof Commercial series of Legrend /L&T /ABB /Scheinder /Simens

200 A 25kA SC for 1 sec

125 amps 15KA SC for 1 sec

100 A 25kA SC for 1 sec

160 amps 15KA SC for 1 sec

Supplying, installing, connecting to existing sandwhich type rising mains, testing and commissioning of following capacity End Feed Unit for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as requiredof Commercial series of Legrend /L&T /ABB /Scheinder /Simens/Eq.make as approved by department.

800 amps 50KA SC for 1 sec

630 amps 50KA SC for 1 sec

400 amps 25KA SC for 1 sec

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as requiredof Commercial series of Legrend /L&T /ABB /Scheinder /Simens

100 Amp, 16 KA,TPMCCB (Icu = Ics)

125 Amp, 16 KA,TPMCCB (Icu = Ics)

150 Amp, 16 KA,TPMCCB (Icu = Ics)

200 Amp, 25 KA,TPMCCB (Icu = Ics)

400 Amp, 35 KA,TPMCCB (Icu = Ics)

630 Amp, 50 KA,TPMCCB (Icu = Ics)

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as requiredof Commercial series of Legrend /L&T /ABB /Scheinder /Simens

100 Amp, 16 KA,TPMCCB (Icu = Ics)

125 Amp, 16 KA,TPMCCB (Icu = Ics)

150 Amp, 16 KA,TPMCCB (Icu = Ics)

200 Amp, 25 KA,TPMCCB (Icu = Ics)

400 Amp, 35 KA,TPMCCB (Icu = Ics)

800 Amp, 50 KA,TPMCCB (Icu = Ics)

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as requiredof Commercial series of Legrend /L&T /ABB /Scheinder /Simens

100 Amp, 16 KA,TPMCCB (Icu = Ics)

125 Amp, 16 KA,TPMCCB (Icu = Ics)

150 Amp, 16 KA,TPMCCB (Icu = Ics)

200 Amp, 25 KA,TPMCCB (Icu = Ics)

SUB HEAD - VII - (CABLES, CABLE TRAY)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required

150 mm. Width x 50mm. Depth x 1.6mm. Thickness.

300 mm. Width x 50mm. Depth x 1.6 mm. Thickness.

450 mm. Width x 50mm. Depth x 2.0 mm. thickness.

600 mm. Width x 62.5mm. Depth x 2.0 mm. thickness.

750 mm width X 62.5 mm depth X 2.0 mm thickness

1000 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required

150 mm. Width x 50mm. Depth x 1.6mm. Thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Ir

on cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

600 mm. Width x 62.5mm. Depth x 2.0 mm. thickness.

750 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required

Supply, laying testing and commissioning of following sizes of FRLS XLPE insulated PVC sheathed armoured aluminium/ Copper conductor cable of 1.1 KV grade on existing cable tray / surface including clamps, ties etc. as required.The job includes providing fixing of copper thimbles of required size and numbers on input and output side. The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates for approval from the department not below the rank of SDO ,prior to the supply of materials

3.5 Core 70 Sqmm.

3.5 Core 95 Sqmm.

4 Core 25 Sqmm. copper

4 Core 16 Sqmm. copper

4 Core 6 Sqmm. copper

3 Core 4 Sqmm copper

Supplying and making end termination with brass compression glands and Al./copper lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required.(Including ferroling of each circuit i/p & o/p side) . The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates for approval from the department not below the rank of SDO ,prior to the supply of materials

4 Core 16 Sqmm. copper

4 Core 10 Sqmm. copper

4 Core 6 Sqmm. copper

3 Core 4 Sqmm copper

Supplying and making end termination with brass compression glands and Al./copper lugs for following size of PVC insulated and PVC sheathed / XLPE Al. conductor cable of 1.1 KV grade as required.(Including ferroling of each circuit i/p & o/p side) . The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates for approval from the department not below the rank of SDO ,prior to the supply of materials

4 Core 16 Sqmm. copper

Supply, installation, testing & commisioning of cable termination of above cables with copper lugs & flameproof brass compression glands on both the ends with inhibting compound etc. complete as required.

4 X 16 sq. mm (28mm)

4 X 10 sq. mm (25mm)

2 X 10 sq. mm (19mm)

1 X 185 sq. mm (19mm)

Supply, laying, testing & commisioning of LPCB/BRE approved Fire Survival armoured cable as per BS 7846, fire Test as per BS 6387 CWZ, copper conductor /mica taped/ Flame Barrier/ Cross Linked Insulation/ Halogen Free Inner Sheath/ SWA/ Halogen Free Outer Sheath (1000V), LPCB Certified for power cables. etc. complete as required. (Tagging to be provided with aluminium strips on both the ends as approved). The Agency / firm has to submit Techanical data sheet (TDS) along with above mentioned requisite certificates for approval from the department not below the rank of SDO ,prior to the supply of materials

4 Core 6 Sqmm.

4 Core 4 Sqmm.

3 Core 4 Sqmm.

3 Core 6 Sqmm.

Supply, installation, testing & commisioning of cable termination of above cables with copper lugs & flameproof brass compression glands on both the ends for fire survival cable with inhibting compound etc. complete as required.

3 Core 10 Sqmm.

Providing & fixing of control wiring/power cabling with following sizes of copper conductor armoured cable between indoor and outdoor units directly on surface of wall/ existing channel i/c making connection etc. as required.

4 x 1.5 sq.mm

3 x 1.5 sq.mm

2 x 1.5 sq.mm

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.6 metre long etc. with charcoal / coke and salt as required.

Providing and fixing 6 SWG dia. GI wire on surface or in recess for loop earthing along with the existing surface / recessed conduits / submain wiring / cable as required.

Providing and fixing 25 x 5 mm G.I. Strip on surface /on existing cable tray for connections etc. as required.

Providing and fixing 8.0 mm dia (SWG) bare copper Wire (having insulation cover at top ) on surface /on existing cable tray for connections etc. as required.

SUB HEAD - VIII - ELV WORKS

Supplying & Fixing of Non- PCB based Information Outlet (I/O) RJ45, Tolless Termination TIA-568C Category-6, Termination of Catergory-6 UTP Cable, UL listed ,Shall conform to Category-6 as per the EIA/TIA-568C.2,Shall support network line speeds up to 1 Gbps, Shall have RJ-45 type connector with bend limiting and strain relief boot for securing IDC contacts from external forces and for maintaining the bend radius of the cable, Shall have minimum duraility of 950 or Above mating cycles and 200 termination cycles. Certified by independent labs like ETL/GHMT/3P for compliance to EIA/TIA-568C.2 complete in all respect.. Make-Siemon/Panduit/Legrand

Supplying & Fixing of Single Faceplate Shall be Duplex Port (RJ45) square plate, dimension as per commercially available modular office furniture.Shall have spring shuttered front access for preventing ingress of dust,Shall be supplied with Gang Box of the same size by System Integrator complete in all respect. . Make-Siemon/Panduit/Legrand

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.of of Havells Crabtree Signia Grand Series (glass finish) /Legrend Arteor Series / L&T Englaze Series (glass finish) / ABB Zenit (glass finish) Series / Siemens Delixi / Schneider Electric Exxact Series . (The Sample must be approved from departmental officer not below the rank of SDO before despatching /Installation of switches-sockets at the work site)

Telephone socket outlet

TV antenna socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.

Supplying and fixing modular type call bell/ buzzer with LED indication, suitable for single phase, 230 volts, complete as required.

1 or 2 Module (75mm X 75mm)

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying, Installation, testing and commissioning of following sizes of 0.5 mm dia annealed tinned copper conductor PVC insulated and PVC sheathed unarmoured telephone cable on surface/ existing cable tray complete as required.

Supplying and drawing co-axial TV cable following grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required

Supplying, erection, testing and commissioning of following tap off / splitter as per specification in 1.6 mm thick CRCA sheet steel enclosure for CATV system.

4 Way splitter box

Supplying and fixing of following sizes of PVC conduit along with accessories in recess including painting after cutting the wall through hydraulic cutter and making good the same in case of recessed conduit as required. (For tel./ TV / Data wiring)

Supplying & Fixing of UTP Jack Panel, loaded with 24 nos UTP ports for Non-PCB based IO Jacks (RJ45, TIA-568C Category-6, Shall have integrated bonding bar or other mechanism for grounding, Shall be loaded with individually replaceable 24 nos. Category-6 certification by Jacks complying with TIA-568.C.2 , Shall be having a 6 port module construction for better cable dressing at the rear, the jacks shall have RJ-45 type connector with bend limiting and strain relief boot for securing IDC contacts from external forces and for maintaining the bend radius of the cable complete in all respect. . Make-Siemon/Panduit/Legrand

Supplying of 4-pair Unshielded twisted pair with a cross filler (+), meeting Category 6 standards as per TIA-568C.2, The cable should be tested till 250 MHz , Shall be Fire-Retardant, Low-Smoke & Zero-Halogen as per IEC 60332-1, IEC 61034-2 & IEC 60754-1 respectively. Make-Siemon/Panduit/Legrand

Supplying & Fixing of Category 6, UTP patch cords shall be constructed of 24-27 AWG unshielded twisted pair stranded copper cable with an enhanc

ed performance modular plug at each end. Patch cord cable shall be offered in multiple colored UTP cable for design flexibility with a clear strain relief boot on each modular plug. All patch cords shall be compatible with both T568A and T568B wiring schemes. UTP Cable will be 1.0 mtr. complete in all respect. Jacket - LSZH . Make-Siemon/Panduit/Legrand

Supplying & Fixing of Category 6 UTP patch cords shall be constructed of 24-27 AWG unshielded twisted pair stranded copper cable with an enhanced performance modular plug at each end. Patch cord cable shall be offered in multiple colored UTP cable for design flexibility with a clear strain relief boot on each modular plug. All patch cords shall be compatible with both T568A and T568B wiring schemes. Blue UTP Cable, 2 Meter complete in all respect. Jacket -LSZH . Make-Siemon/Panduit/Legrand

Supplying & Fixing of Fiber Optic LC style fully loaded Patch Panel (FOPP), 19" Rack Mount ,Shall have all accessories including coupler plates pre loaded with 12 Nos of LC couplers (OM3) with all accessories complete in all respect. Pigtails Should Complie to ITU-G657.B-Bend insestive fiber. Make-Siemon/Panduit/Legrand .

Supplying & Fixing of Fiber Optic LC style fully loaded Patch Panel (FOPP), 19" Rack Mount ,Shall have all accessories including coupler plates pre loaded with 24 Nos of LC couplers (OM3) with all accessories complete in all respect. Pigtails Should Complie to ITU-G657.B-Bend insestive fiber.. Make-Siemon/Panduit/Legrand

Supplying & Fixing of Fiber Optic Patch Cable (LC-LC), 3 Mtrs. Long, ISO/IEC-11801-OM3 50μ Duplex, LSZH,All patch cords shall conform to EIA/TIA-568C.3 and ISO/IEC-11801,Shall be Duplex Multi Mode Fiber Optic Patch Cords OM3 50μ,Shall support network line speeds up to 10 Gbps.Shall have LC-LC Connector connectors at the ends complete in all respect.. Make-Siemon/Panduit/Legrand

Supply & Fixing of OM3 50/125μ Type Pigtails of ISO/IEC-11801-OM3 Pigtails with LC Type Connectors,pigtails for terminating fibers on the FOPP complete in all respect. Make-Siemon/Panduit/Legrand .

Supplying, Installation, Testing & Commissioning of 50μ, 6-core Multi mode OM3 metallic armored Fiber cable as per ISO/IEC-11801, Shall be able to meet Gigabit & 10 Gigabit Ethernet performance up to 300 meters requirement specified by IEEE 802.3z (1000 Base-X) & IEEE 802.3ae (10G Base-X) Tensile load should be 4000 Newton or higher and crush resistance should be 4000 Newton or higher ,The attenuation @ 850 nm should be ≤ 2.7 (Max) db/Km and @ 1300 nm should be ≤ 0.7 (Max) dB/Km, the fiber construction can be unitube or multitube, but tensile and crush resistance parameters should be matched, the jacket shall be FRLSZH complete in all respect. . Make-Siemon/Panduit/Legrand

Supplying, of 50 Pair anealed tinned copper conductor PVC insulated and sheathed armoured copper telephone cables with suitable clamps, saddles and including making terminal joints complete as required.Make-Finolex/Delton/Vimco

Supplying, Installation, Testing & Commissioning of of 50 Port telephone Jack Panel Approved.. Make-Siemon/Panduit/Legrand .