SPL REPAIR AND REPLACEMENT OF OLD VINTAGE LT PANEL FEEDER PILLAR BOX AND LT CABLE AT DIFFERENT LOCATIONS IN U AREA SHIVMANDIR UNDER SUKNA AND CERTAIN OTHER SANCTIONED WORKS IN SUKNA MIL STN UNDER GE SUKNA

Amount

M&L brick work with fly ash brick, straight or curved on plan exc. 6 m mean radius built in CM 1:6 complete all as specified and as directed.

M&L for Brick work with Fly ash bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all specified and directed.

S&F in repair stainless steel towel rail 600 mm long of brass chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

M&L Coloured glazed ceramic tiles 300x 450x 7 mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick backing with cm 1:4 complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick backing in CM 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and fair complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or stone masonry or on one side of lathing surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed.

M & L for painting the new WALL surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of newly plastered or previously untreated surfaces of walls (b) Putty application- Applying a thin layer of wall care putty to obtain smooth finish (c) Priming surface- Applying one coat of cement base primer (d) Painting- Applying two coats of oil bound distemper.

M & L for painting the new wall surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of newly plastered or previously untreated surfaces of walls (b) Putty application- NIL (c) Priming surface- Applying one coat of alkali resistant primer (d) Painting- Applying two coats of cement base paint.

Taking up or down 15 mm bore steel tubing and connections, complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

S&F in repairs 15 mm bore bib tap chromium plated long body fancy type, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule & fixed complete all as specified and directed.

S & F in repair 15 mm bore stop valve / angle valve fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S & F in repairs Grating doom 100 mm dia with waste hole of PTMT. (Minimum weight 25gms) complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts, of length 450 mm & suitable for hot water supply complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F in repairs vitreous china european water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F vitreous china wash hand basin white flat back of size not less than 630 x 450 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S&F in repairs soap dish, with metal dish brass chromium plated fixed to plugs complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

S&F Cast iron floor / Nahani trap 75 mm dia outlet, with grating including jointing to waste pipe fixed in cement concrete type B1 1:2:4 complete all as specified and directed.

Dismantiling & Taking down the old vintage existing LT Panel board by disconnecting existing incoming and outgoing LT cables carefully and removing from site complete all as specified and directed.

Supply, installation, testing and commissioning of Panel board not less than 1.80m x 1.50m x 0.80m, outdoor cubical type factory made (CPRI approved), double door, front & back both side openable type fixed with Butt Hinges and locking arrangement with Aldrop latches, fabricated of CRCA sheet, inner sheet 2.0 mm thick hinged type door for individual MCCBs and outer door 3.15 mm thick, rubberised gasket, supported on 50x50x6 mm angle iron and Tee section frame dust and proof complete with aluminium bus bar 4 Nos 600 Amps rated capacity mounted on porcelain insulators totally enclosed chamber for protection 3 phase 415 volt with suitable capacity bus bar/ PVC insulated copper cable control wiring duly mounted on PCC foundation with suitable size of bolts, nuts & washers. Panel board shall be powder coated and angle iron frame painted with black synthetic enamel paint over a coat of red oxide primer complate, connecting existing cables with suitable size glands and lugs to accommodate and including the following:-

Supply, installation, testing and commissioning of Panel board not less than 1.50m x 1.20m x 0.50m, outdoor cubical type factory made (CPRI approved), double door, front and back both side openable type fixed with (CPRI) approved, double door, front & back both side openable type fixed with Butt Hinges and locking arrangement with Aldrop latches, fabricated of CRCA sheet, inner sheet 2.0 mm thick hinged type door for individual MCCBs and outer door 3.15 mm thick, rubberised gasket, supported on 50x50x6 mm angle iron and Tee section frame dust and proof complete with aluminium bus bar 4 Nos 600 Amps rated capacity mounted on porcelain insulators totally enclosed chamber for protection 3 phase 415 volt with suitable capacity bus bar/ PVC insulated copper cable control wiring duly mounted on PCC foundation with suitable size of bolts, nuts & washers. Panel board shall be powder coated and angle iron frame painted with black synthetic enamel paint over a coat of red oxide primer complate, connecting existing cables with suitable size glands and lugs to accommodate and including the following:-

Supply, installation, testing and commissioning of Panel board not less than 0.800m x 0.600m x 0.50m, outdoor cubical type factory made (CPRI approved), double door, front and back both side openable type fixed with (CPRI) approved, double door, front & back both side openable type fixed with Butt Hinges and locking arrangement with Aldrop latches, fabricated of CRCA sheet, inner sheet 2.0 mm thick hinged type door for individual MCCBs and outer door 3.15 mm thick, rubberised gasket, supported on 50x50x6 mm angle iron and Tee section frame dust and proof complete with aluminium bus bar 4 Nos 600 Amps rated capacity mounted on porcelain insulators totally enclosed chamber for protection 3 phase 415 volt with suitable capacity bus bar/ PVC insulated copper cable control wiring duly mounted on PCC foundation with suitable size of bolts, nuts & washers. Panel board shall be powder coated and angle iron frame painted with black synthetic enamel paint over a coat of red oxide primer complate, connecting existing cables with suitable size glands and lugs to accommodate and including the following:-

M&L for on site repair of front and rear doors LT Panle size 500mm x500mmx 500mm including welding of butt hinges 06 Nos on front side and as per requirement on back side, aldrop latches on front and rear side, spray painting with synthetic enamel paint (one coat) complete all as specified and directed.

M&L for on site repair of front and rear doors LT Panle size 1000mm x800mmx 500mm including welding of butt hinges 06 Nos on front side and as per requirement on back side, aldrop latches on front and rear side, spray painting with synthetic enamel paint (one coat) complete all as specified and directed.

M&L for on site repair of front and rear doors LT Panle size 1200mm x800mmx 500mm including welding of butt hinges 06 Nos on front side and as per requirement on back side, aldrop latches on front and rear side, spray painting with synthetic enamel paint (one coat) complete all as specified and directed.

Excavation in trenches in any type of soil (soft/loose soil) not exceeding 1.5 metre wide and not exceeding 1.5m in depth LT under ground cables/GI pipes for trenches, complete all as specified and directed.

Returning, filling in, including spreading watering and well ramming in layers not exc 25cm in layers, complete all as specified and directed.

Removal of surplus soil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point, complete all as specified and directed.

S&F of DWC Pipe IS-16205, size inner dia 59.8 mm, outer dia 76.4 mm for cable protection in wall/under fround laying of UG cables including SNAP-FIT Coupler and all fittings as required at site complete all as specified and directed by Engr-in-charge.

S&F of DWC Pipe IS-16205, size inner dia 39.3 mm, outer dia 51 mm for cable protection in wall/under fround laying of UG cables including SNAP-FIT Coupler and all fittings as required at site complete all as specified and directed by Engr-in-charge.

Supply and fixing in repair of GI tubing light grade 80mm dia for protection pipe along with nuts bolts washers or laid in trenches under roads including taking down old unsv complete all as specified and directed.

Supply and fixing in repair of GI tubing light grade 40mm dia for protection pipe along with nuts bolts washers or laid in trenches under roads including taking down old unsv complete all as specified and directed.

Boring/Drilling (horizontally) manually upto 2m depth in soil below existing road suitable for passing GI tubing of 40 to 80 mm bore and getting out and disposal of soil to a dist n.exc 50 meter complete all as specified and directed by Engr-in-Charge.

Taking down old unsv LT cables any size from poles/trenches after disconnecting the cable from panels/poles etc complete all as specified and as directed.

Supply,laying testing and commissoning of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sqmm 4 core complete all as specified and directed..

Supply,laying testing and commissoning of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 sqmm 4 core complete all as specified and directed..

Supply,laying testing and commissoning of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 50 sqmm 4 core complete all as specified and directed.

Supply,laying testing and commissoning of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 95 sqmm 4 core complete all as specified and directed..

Supply,laying testing and commissoning of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 150 sqmm 4 core complete all as specified and directed..

Supply,laying testing and commissoning of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 400 sqmm 4 core complete all as specified and directed..

M&L in replacements earthing complete with galvanised steel earth plate electrode of size 600 x 600 x 6 mm thick buried directly in ground in vertical position (earth pit not less than 2.25 m deep below the normal ground level) with top edge of the earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead of GI strip 32x6 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel, all as shown in electrical plate No. 3 connected to earthing test point and including dismantling complete all as specified and directed. Note:- The unit rate shall also include for earth work in any type of soil, PCC 1:3:6 type C1 chamber, RCC 1:1.5:3, type A1 cover slab, 50 mm thick reinforced with 8 mm dia TMT bar @ 140 mm C/C both ways, 10 mm dia plain bar lifting handle embedded in cover slab, 20 mm bore medium grade GI watering pipe, 40 mm bore GI medium grade earth lead protection pipe, funnel, wire mesh, copper lugs, charcoal and common salt in alternate layer etc.

MS ORIENT ENGINEERING WORKS (BID ID -3454830)

R N De (BID ID -3455657)

M/S GLORIOUS CONSTRUCTION (BID ID -3456000)

R K UDYOG (BID ID -3455106)

Janata Enterprises (BID ID -3455584)

M/S RANEN PAL (BID ID -3455574)

B.B.Enterprise (BID ID -3455606)

ELECTRO WIR WAY (BID ID -3454738)