Installation of open-gym equipment at various parks and locations within the Council area.

Providing and installation of Uday Creations kilkari, Arihant, Svr, Arasu make 8 in combination set:- *PRODUCT DIMNSIONS: - D.I.A 4000mm *SAFE WORKOUT AREA: - D.I.A. 5000mm *Combination made from “B” Class G.I. pipe. The octagonal structure is made up of 100mm NB “B” class GI pipe. Round plate of 250mm diameter & 10mm thickness is welded at bottom of octagonal Structure. The links are made up of 25mm NB “B” class G.I. pipe. The handle and seat frame of seated puller is made from 32mm NB “B” class G.I. pipe. For the assembly different bushes are used which is made from seamless pipe of 50mm OD and 5mm thickness & 5mm solid bar is used. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mm x 300mm x 2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20mm with no sharp edges. Leg press footrest consists of 25 NB diameter hardened low carbon steel material. The nut Bolts used for assembly are made from S.S. material. The bushes (stopper) used to avoid the collusion made from Poly Urethin Plastic material of 50mm diameter. Surfing frame is of 32NB made from “B” Class G.I. pipe. 300mm diameter x 10mm thick plate can be used for rotating sear of seating twister with 50 NB vertical G.I. pipe. Closing caps made from high quality FRP material which is of 2mm thickness. The pints used are made up of 17mm diameter solid bar. The bearing used are of “6205” permanent lubricated sealed bearing of reputed make. The nut bolts used for assembly are made from M.S. pre-galvanized material. A17, A24, A34 circlips are used for assembly. The footrests are made from casted Aluminum material. Having sizes 130mm x 310mm x 5mm thick. With the support of 310mm x 130mm x 3mm thick MS plate. It has Bolting provision for mounting on concrete slab.

Providing and installation of Uday Creations kilkari, Arihant, Svr, Arasu make 5 in 1 combination (shoulder press+ chest press+ knee chair+ seating and standing twister) • PRODUCT DIMENSIONS: - 2410mm (Length) x 1720mm (Width) x 2350mm (Height). • SAFE WORKOUT AREA: - 4500mm (Length) x 4500mm (Width). Combination made from “B” Class G.I. pipe. The center pipe is of 100mm NB pipe. Round plate of 248 mm diameter & 9mm thickness is welded at bottom. The links are made up of 25mm NB pipe. The handle and seat frame of shoulder press is made from 32mm NB pipe. For the assembly different bushes are used which is made from seamless pipe of 50mm OD and 5mm thickness & 50mm solid bar is used. Chest press frame is of 32mm NB pipe. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mm X 300 mmX1.8mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. The chest press footrest consists of 25 NB pipe. The pins used in are made up of Φ25 mm, Φ35mm & Φ45mm bright material. The Nut Bolts used for assembly are made from height tensile steel with galvanized material. The bushes (stopper) used which are made from Poly Urethin Plastic material of 48 mm diameter. Surfing pedal is of 32NB pipe. Knee chair handle frame is of 32NB pipe. 298mm diameter x 9mm thick plate is used for rotating seating of standing twister with 50NB pipe. Closing caps made from best quality HDPE/LLDPE material in attractive colors. The pins used are made up of 17mm diameter solid bar. The bearing used are of “6203”, “6205”, & “6007” permanent lubricated sealed bearing of reputed make. The nut bolts used for foundation assembly are made from M.S. pre-galvanized material. A17, A24, A34 circlips are used for assembly. The footrests are made from casted Aluminum material, having sizes 125mm X 305mm X 4mm thick. With the support of 305mm X 125mm X 2.9mm thick MS plate. It has Bolting provision for mounting on concrete slab. Polycarbonate sheet is used for roof with supporting frame which is made from Dia. 25mm NB pipe. MS 7.8mm thick round plate is used for splitting roof structure from main frame. Handle grips are provided which is made of high quality rubber material. The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with minimum 60 to 70 micron thickness.

Providing and installation of Uday Creations kilkari, Arihant, Svr, Arasu make Air Walker- DIMENSIONS: - 1060mm (Length) x 810mm (Width) x 1600mm. (Height). SAFE AREA:- 2.0 Meter x 1.8 Meter Air Walker Equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G.I. Pipe will be of Apollo, Tata, Jindal, Swastik, Zenith or Siddharth. The main frame pipe is of 80mm NB made from “B” Class G.I. Material which is bending at the radius of 250mm. The Sleeve frame is of 100 OD and M.S. Seamless Pipe with thickness 5mm. This sleeve can be easily disassembled from main frame. The bottom support of M.S. round plate of 0250mm & 10mm thick. The leg movement frame is of 32NB made from “B” Class G.I. pipe. This link is supported with MS flat of size 60X8mm. The handle frame is of 25NB made from “B” Class G.I. Pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of 0250mm & 10mm thickness and 20mm x 25mm M.S. angles of 3mm thickness and 20mm x 40mm CRC square pipes. Foundation cover Closing Cap is made from FRP Material with 0.7mm thickness. Closing Caps are made up of high quality reinforced Plastic material. A24 circlips are used for assembly. The bearings used are “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel galvanized nuts & bolts are used for assembly. The powder coating is done by Pure Polyester powder of Ackzonoble or Berger Paints with 60 to 70 micron thickness. The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 250mm X 115mm X 3mm thick MS plate. To build structure bushes are used which are made from M.S. made of SS 304 used on nylon cap mounted on pins to protect and pins from rain and dust.

Providing and installation of Uday Creations kilkari, Arihant, Svr, Arasu make SHOULDER BUILDER SINGLE – General Information: Product Area: - 2 X 0.9 mtr Safe Play Area: - 3 X 1.9 mtr. Technical Specification:- 25 NB Galvanized pipe bend to form ring and spokes consists of 20 NB G.I. pipes that connect to each other to form a wheel of SHOULDER TWIRL. This wheel is fixed to 80 NB main support galvanized pipe with the help of 40 NB connector pipe with specially designed bearing. Bearing used are oil sealed self – lubricated made by reputed company. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI /HDPE caps for user safety against entrapment. Handle for rotating the ring fixed over the pipe ring.

Providing and installation of Uday Creations kilkari, Arihant, Svr, Arasu make TRIPLE STANDING TWISTER – DIMENSIONS: - 1150mm (Length) x 1150mm (Width) x 1580mm (Height). SAFE AREA: - 02.1Mtr. Triple Twister made from “B” Class G.I. Galvanized (G.I.) Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The Center Pipe is of 80NB made from “B” Class G.I. pipe. The bottom support welded is of M.S. round plate of 0250mm & 10mm thick. The standing frame is of 32NB made from “B” Class G.I. pipe. The handle frame of triple twister is of 25mm NB made from “B” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB “B” class welded with M.S. round plate of 0250mm & 10mm thick. Main pipe supported with 25 mm x 25 mm M.S. angle of 3mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness. The standing plate is fitted on the frame made up of 0 80 NB GI. Pipe. M.S. Round Plate of size 0300mm x 10mm thickness. Closing Caps are made up of high quality Fiber reinforced Plastic material. The Pins used are made up of 0 35 mm SAE 8620 bright material. The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts are used for assembly. The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness.

Providing and installation of Uday Creations kilkari, Arihant, Svr, Arasu make CYCLE NEW MODEL- Area - 1.8 x 0.8 mtr. Safe Area – 2.8 x 1.8 mtr. Height – 1.10 mtr. Providing & fixing of Cycle having its required Area (6’0” x 2’6”) and height of 3’6” Feet. The wheel of cycle should be made by 2” x 2” square pipe with wheel support of 2 nos. half round plate of thickness. The Handle & Centre support should be made by 1’6” x 1’6” Square pipe & handle should be made by 25mm ‘B’ class pipe for balancing the cycle. The seating arrangement should be supported by 5mm thick plate & the FRP seat of size (13” x 13”) to seat properly on the cycle. The mechanism of the paddle consist of 2 nos. 6305 heavy duty bearing of reputed make with shaft, solid bar & bush for smooth operation of the cycle.

Providing and installation of Uday Creations kilkari, Arihant, Svr, Arasu make LEG PRESS DOUBLE - *DIMENSIONS: -1840mm (Length) x 360mm (Width) x 1560mm. (Height). *SAFE AREA: - 2.8Mtr x 1.4Mtr. *Leg press equipment made from “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. *Make of G I Pipe will be of Tate, Apollo, Jindal, Swastik, Zenith or Siddharth. *The center pipe is of 100mm NB made from “B” Class G.I. pipe. *The Sleeve frame is of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This sleeve can be disassembled from main frame. *The bottom support of M.S. round plate of 0250mm & 10mm thick. *The remaining outer frame is of 32NB made from “B” Class G.I. pipe. *The foundation used for fixing is structure and made from center pipe of G.I. of 80mm NB “B” Class welded with 25mm X 25mm M.S. angles of 3mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness. *Seat & Back rest provided are made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm. *The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 310mm X 130mm X 3mm thick MS plate. *The frame of footrests made up of 25NB “B” Class G.I. pipe. * Closing Caps are made up of high quality Fiber reinforced Plastic material. *To build structure bushes are used which are made from M.S. seamless pipe of 50mm O.D. and 5mm thickness. *The pins used are made up of 025mm SAE 8620 bright material. *The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed Brand (SKF/FAG). *High tensile steel with galvanized nut bolts are used for assembly. *The cerclips used for assembly are of A24mm. *The powder coating done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness.

Providing and installation of Uday Creations kilkari, Arihant, Svr, Arasu make ARM PULLAR DOUBLE- DIMESIONS: - 1900mm (Length) x 740mm (Width) x 1920mm (Height). SAFE AERA: - 1.2Mtr x 3Mtr. Seated puller equipment made up of “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Apollo, Tata, Jindal, Swastik, Zenith or Siddharth. The center pipe is of 100NB made from “B” Class G.I. pipe. Bottom support is of M.s. round plate of 0250mm & 10mm thickness is welded. All linkages are made up of 25NB “B” Class G.I. pipe. The handle frame is of 32NB “B” Class G.I. pipe. The seat frame is of 32NB “B” class G.I. pipe. To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB “B” class. Welded with M.S. round plate of 0250mm & 10mm thick. Main pipe supported with 25mm X 25mm M.S. angles of 3mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation cover Closing Cap is made from FRP Material. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mm X 300mm X 2mm thickness and form radius of 20 mm with no sharp edges. Closing Caps are made up of high quality Fiber reinforced Plastic material. Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. The bearings used are of “6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used of assembly are of A16. The powder coating done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness.

Providing and installation of Uday Creations kilkari, Arihant, Svr, Arasu make HORSE RIDER- *DIMENSIONS: - 1180mm (Length) x 400mm (width) x 1400mm. (Height) *SAFE AREA: - .2.2Mtr X 1.4Mtr. *Horse rider equipment made from “B” Class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. * Make of G I Pipe will be of Tate, Apollo, Jindal, Swastik, Zenith or Siddharth. *The main frame of 100NB made from “B” Class G.I. pipes welded with M.S. round plate of 0250mm & 10mm thick. *Seat provided are made up of MS deep quantity of 2mm thickness with no joint with uniform outer edge radius 20mm. *The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class Welded with M.S. round plate of 0250mm & 10mm thick. Main pipe supported with 25 mm X 25 mm M.S. angles of 3mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. *The leg movement frame is of 32NB made from “B” G.I. pipe. *The handle frame is of 32NB from “B” Class G.I. pipe. *The footrests are made from 25 NB “B” class G.I. pipe. *Pins used of Diameter 17mm are made up from SAE 8620 bright material. *High tensile steel with galvanized nuts & bolts are used for assembly. *The circlips used for assembly are of A24mm. *The powder coating done with Pure Polyester powders of Ackzonoble or Berger with 60 to 70 micron thickness.

Providing and installation of Uday Creations kilkari, Arihant, Svr, Arasu make SURF BOARD SINGLE - *DIMENSIONS: - 910mm (Length) x 860mm (Width) x 1400mm. (Height). *Safe Area: - 1.39Mtr x 1.27Mtr. *Surf Board Equipment made from “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. * Make of G I Pipe will be of Tate, Apollo, Jindal, Swastik, Zenith or Siddharth. *The center pipe is of 100mm NB made from “B” class G.I. pipe. *The sleeve pipe is of 125mm OD seamless pipe with thickness of 5mm and bolted to main frame with M10 SS bolts. *The bottom support welded of M.S. plate of 0250mm & 10mm thickness. *The handle frame is of 25NB made from “B” class G.I. pipe. *The paddle frame is of 25NB made from “B” Class G.I. pipe is supported with 70x8mm bend M.S. flat and can be replaceable. *The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB “B” class welded with M.S. round plate of 0250mm & 10mm thick. Main pipe supported with 25mm x 25mm M.S. angles of 3mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. *Bushes are used 70mm Outer Diameter with 5mm thickness is used. *The footrests made from Aluminum casting material of size 320mm x 270mm x 5mm. *For support to footrest 200mm x 250mm with 3mm thickness M.S. Plate used. *Closing Caps are made up of high quality Fiber reinforced Plastic material. *The pins used are made up of 035mm SAE8620 bright material. *The bearing used are of “6007zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). *High tensile steel with galvanized nut bolts are used for assembly. *The cerclips used for assemble A24. *The powder coating is done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness.