Spl repair to Bldg No NP-41 of TK TPTR PL Asc, Addn/ altn to Bldg No. E-35 at SHO (L), provn of separate toilet for lady offrs near Bldg No. E-08 of Fd Hosp and Addn/ altn to Boundary wall of SHO under GE (East) Ferozepur Cantt

Amount

Dismantling of brick tiles single layer laid on roof jointed & pointed in cement mortar complete all as specified and as directed by Engineer-in-charge.

Demolition mud in roofs, any thickness, including plastering and leaping etc including removing rubbish upto 500 mtr from the site complete all as specified and as directed by Engineer-in-charge

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in roof padding complete all as specified and directed by Engineer-in-Charge.

M&L for Rendering 10 mm thick cement mortar 1:4 mixed with integral water proofing compound as per manufacturer instruction over the padding concrete while still the concrete is still green,complete all as specified and as directed by Engineer-in-charge

M&L for water proofing treatment to roof surface including parapet wall comprising with the following course of treatment/Specifications from bottom to top:- (a) Applying evenly a tack coat of industrial bitumen 85/25@ 1.2 kg per sqm over a coat of bitumen primer @ 0.30 ltr per sqm including prepration of roof surfaces complete all as specifiedand as directed by Engineer-in-Charge. (b) One layer of APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) land on primed surface by torched application.Polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside groove of parapet walls and shall be finised by a membrane flashing. Note:- (i) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions. (ii) A minimum overlap shall be 75 mm length wise and 100 mm width wise of polymeric membranes repectively ansd sealed all overlaps and joints as manufacturer's instructions. (iii) The whole works shall be executed by the authorised company applicator.

M&L for two coat of aluminium paint over APP membrane complete all as specified and as directed by Engineer-in-charge

Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins, arches, pillars etc complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in c:m 1:6, complete all as specified and directed.

All as per srl item No 08 here-in-before but using old bricks retrieved from dismantling under ser item 7 here-in-before including cleaning and removal of mortar from old bricks etc complete all as specified and directed.

Taking down cement plaster on brick walls of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Rendering 12 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for Rendering 15mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for Rendering 5 mm thick cement plaster on ceiling surfaces in cement mortar 1:4 finished fair and even without using extra cement, complete all as specified and directed.

Complete removal of existing wall finishes, any type by vigorously wire brushing, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of existing finishes & foreign materials, making good minor surface imperfections such as holes, dents cracks etc in CM 1:3 & applying 02 mm thick waterproof wall putty on the bldg internall surface of wall with uniform thickness incorporating water proof putty @ 2.00 kg/Sqm & making surface absolutely smooth on entire satisfaction of Engineer-in-Charge.

M&L for applying two coat of distempering new plaster surface with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology to prepare the surface even and smooth on new surface, complete all as specified and directed.

Complete removal & applying two coat of distempering wall surface with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology and providing 2mm thick waterproof based wall putty and sanding the surface to prepare the surface even and smooth, complete all as specified and directed.

M&L for applying two coat of distempering new plaster ceiling surface with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology to prepare the surface even and smooth on new surface, complete all as specified and directed.

Complete removal of existing wall finishes, any type by vigorously wire brushing, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of existing finishes & foreign materials, making good minor surface imperfections such as holes, dents cracks etc in CM 1:3 & applying 02 mm thick waterproof wall putty on the bldg internall surface of ceiling surface with uniform thickness incorporating water proof putty @ 2.00 kg/Sqm & making surface absolutely smooth on entire satisfaction of Engineer-in-Charge .

M&L for applying two coat of distempering new plaster / Putty surface with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology to prepare the surface even and smooth on new Ceiling surface complete all as specified and directed.

Complete removal of existing wall finishes, any type by vigorously wire brushing, brooming, dusting & finally washing with water to clean the surface absolutely free from any kind of existing finishes & foreign materials, making good minor surface imperfections such as holes, dents cracks etc in CM 1:3 & applying 02 mm thick water proof wall putty on the bldg external surface of wall with uniform thickness incorporating water proof putty @ 2.00 kg/Sqm & making surface absolutely smooth on entire satisfaction of Engineer-in-Charge

M&L for applying new surface i.e completed removed surface putty treated surface/new plaster surface two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm the surface even and smooth, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size not exceeding 1.5 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts and removing from site to store or otherwise as directed, complete all as specified and directed.

All as per srl item No 22 here-in-before but size exceeding 1.5 Sqm and not exceeding 4 Sqm each, complete all as specified and directed.

Taking down shutters only of any description exc 1 sqm and not exc 2 sqm each including removing from site to store or otherwise as directed, complete all as specified and directed.

S&F Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 125mm x 60 mm including one shop coat of red oxide primer, complete all as specified and directed.

S&F for Pressed steel frames (1.25mm sheet thickness) for doors with one or more rebates including necessary fixing lugs , hinges, lock plate, etc., size of frame 105mm x 60 mm including one shop coat of red oxide primer, complete all as specified and directed.

S&F 30 mm thick, flush shutter, solid core construction,with particle board core and plywood face panel, commercial type both sides, complete all as specified and directed.

S&F 35 mm thick,2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified and directed.

S&F Factory made box type steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-1019/08 & CEJZ/TD-1020/08”.

S&F Factory made box type steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-1019/08 & CEJZ/TD-1020/08”

S&F Factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drg No CEJZ/TD-1019/08 & CEJZ/TD-1020/08”

M&L for Mild steel framed work of E-165 (Fe 290) as in grills/guard bars shouldered with steel window/ ventilator frames including red oxide primer coat, complete all as specified and directed.

S&F solid PVC door frames fabricated and supplied by authorized fabricated of size 50 mm x47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube, complete all as specified and directed.

S&F Factor made solid PVC Door, Shutter 30 mm thick fabricated and supplied by authorized fabricated (Style) consisting of frame made out of MS tubes for top and bottoms rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channels having a PVC sheet strip of 20 mm width struck in side with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rail on either side and as gap insert for Top rail & bottom rail, Paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

Dismantling of boarding, any description, fixed in any position with nails, complete all as specified and directed.

S & F factory made PVC cup boards/ Shelf / Partition of required size consisting of panel of 18mm thick Celuka PVC Ply and for supporting the hold of Shelf/ Partition and shall provided 3 edges in size 18mm x18mm as per required length. The front side of the edge visible in the front of the shelf/ Partition to be edge lipped by 18mm width x 1mm thick PVC sheet using solvent cement etc, complete all as specified and directed. Note Colour of PVC shelf approved by Engr -in charge.

M&L for Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

M&L for Preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed.

S&F PTMT butt hinges, 100 mm long and fixed with steel screws, complete all as specified and directed.

S&F Aluminium bow handle 150 mm long and fixed with steel screws, complete all as specified and directed.

S&F Aluminium tower bolts 150 mm long and fixed with steel screws, complete all as specified and directed.

S&F 300 mm long mild steel, sliding door bolt, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including bolts and nuts, complete all as specified and directed.

S&F Continous (piano) hinges of mild steel bright finish or electro galvanised with flap (when open) 30mm,fixed with steel screw, complete all as specified and directed.

S&F in repair 100mm long hasp and staple, safety type, aluminium anodised including bolt to hinge plate and fixed with screws and fixed, complete all as specified and directed.

S&F 150 mm Floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring complete all as specified and as directed.

S&F 300 mm mild steel ordinary rat tail spring including roller and roller plate, complete all as specified and directed.

S & F Wire cloth galvanised mild steel, 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples, complete all as specified and directed.

S&F 3 mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm, complete all as specified and directed.

S&F Mild steel curtain rod powder coated with fixing side brackets,end cups,rings @ 10 Nos per running metre and fixed with PVC rawl plugs & steel screws as in repairs, complete all as specified and directed.

Demolition of un reinforced cement concrete of any description and in any position not otherwise specially provided for, complete all as specified and directed.

M&L for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in roof kerbs or mud stops, bed blocks,back filling in chowkhats, benching etc including necessary form work, complete all as specified and directed.

M&L for Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints, complete all as specified and directed.

M&L 25 mm thick cement concrete (1:2:4) type B-1 using (20 mm graded crushed stone aggregate) as in sub base of flooring,surface finished rough to receive floor topping, complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons laid bedded , dry and pointed etc, complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level), complete all as specified and directed.

Cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base of floor topping, 75 mm thick, complete all as specified and directed.

M & L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade, jointed and pointed with gray cement and pigment over sand cushioning complete all as specified and directed. Note :- The colour of tiles Red/Yellow approve by Engr -in -charge.

M & L sand filling under floors or in foundations, for cable cushioning to underground cable protection including watering and consolidation complete all as directed by Engieer-in-charge .

Dismantling floor hearth or wall/stone tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M & L Non - skid Ceramic tiles coloured 7 to 8 mm thick (square/ rectangular),primium quality area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and incl screed bedding 15mm thick in cm(1:6), complete all as specified and directed.

M & L for joint less coloured Non - skid Ceramic tiles coloured 7 to 8 mm thick (square/ rectangular),primium quality area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and incl screed bedding 15mm thick in cm(1:6), complete all as specified and directed.

M & L Non - skid Ceramic tiles coloured 7 to 8 mm thick (square/ rectangular),primium quality on vertical surfaces such as in skirting /dado etc area of each tile exceeding 0.11 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 10 mm thick rendering in cement mortar (1:4), complete all as specified and directed.

Glazeded ceramic coloured (colour & shade as approved) tile 450x300x6to7mm thick on vertical surface such as skirting / dados set and jointed in neat cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white/ coloured cement with pigment to match the colour of tiles, complete all as specified and directed.

M&L for Machine cut kota stone slab 18 to 20 mm thick as in flooring of size not less than 0.25 Square metre each, set and jointed in cement slurry over& including screed bed of 20 mm thick in cement mortar (1:6) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and polishing, complete all as specified and directed.

M&L for Machine cut kota stone slab 20-25 mm thick as in skirting,dado of length not less than 500 mm each unit, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and polishing, complete all as specified and directed.

M&L for Granite(holes for gas pipe) tiles18- 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 10 mm thick plaster as in back coat CM 1:4 complete including making circular gas pipe hole, moulding at corners and polishing type, complete all as specified and directed.

Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed.

All as per item No 67 here-in-before but 20 mm bore tubing, complete all as specified and directed.

M&L for GI steel water tubing, 15mm bore medium grade galvanized with all fittings and fixed to walls and celling or laid in floor, complete all as specified and directed.

All as per item No 69 here-in-before but 20 mm bore tubing, complete all as specified and directed.

Fixing only, after cleaning old steel water tubing,15 mm bore and connections in new or old position using new fittings complete all as specified and directed. (pipes obtained from item 67 to be reused).

All as per item No 71 here-in-before but 20 mm bore (pipes obtained from item 68 to be reused), complete all as specified and directed.

S & F Bib tap of cast copper alloy fancy type, 15mm bore, with crutch or butter fly handle, screwed down,screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F in repair stop valves, fancy type, CP with long shank and cup (concealed type), screwed both ends for 15mm bore of iron pipe or for union and fixed, complete all as specified and directed.

S & F central hole basin mixer for wash hand basin including all fittings ie including connection pipe as per manufactures specification complete all as specified and directed. (Make Parko/ESSCO/Prayag.

S&F in repair stop valves/angle cock,fancy type cast copper alloy,screwed down, high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed.

S&F in repair gunmetal gate valve of 20mm dia with iron wheel head screwed both ends for iron pipe, complete all as specified and directed.

S&F PVC waste pipe 32 mm bore suitable to waste coupling pipe attach with rubber ring joints fixed to waste coupling of sinks / WHBs, complete all as specified and directed.

S & F 15mm bore PVC connection with brass nuts on both ends, 450 mm long with PTMT nuts, complete all as specified and directed.

S&F in repair 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe all as specified in SSR Part-I, complete all as specified and directed.

S&F Vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flus pipe and connection to trap, and to flushing pipe, anti-syphonage pipe, etc, complete all as specified and directed.

S&F PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc, complete all as specified and directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and astes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed

S&F Vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste coupling fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing, complete all as specified and directed..

S&F in repair 125 mm chromium plated shower rose with or without swivel joints any size including fixing to steel pipe or union, complete all as specified and directed.

S&F n repair Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed to walls with steel screws and wooden/rawl plugs, complete all as specified and directed.

S & F corner glass shelves 300 mm radius 8 mm thick as per sample radius for bathroom, fixed on suitable support of brass chromium plated clips complete all as specified and directed. (Make: Prayag, Somany, Cera).

S&F in repair Stainless steel soap dish (not less than 1mm thick) of type as directed,fixed to walls with chromium plated brass screws with wooden/rawl plugs, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed .

S&F Mild steel framed work of Fe-410-0 or Fe-310-0 (Fe-290 Gde-E-165) as in doors or gate of angle or other section with gusset plates,rails, braces etc and fixing, complete all as specified and directed.

Taking down eaves gutter and rain water pipes any size or pattern including all fitting heads shoes bends swan - necks etc all specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified and directed.

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches, complete all as specified and directed.

S&F 110 mm dia PVC ( rain water ) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified & directed.

S & F PVC (SWR) bend (any radius), 75 mm bore, diminishing pieces or tapers (larger bore measured) jointed in cement mortar, complete all as specified and directed.

S & F PVC (SWR) bend (any radius), 110mm bore, diminishing pieces or tapers (larger bore measured) jointed in cement mortar, complete all as specified and directed.

S&F 75mm dia Junction single (Single or double T) equal or unequal complete all as specified and directed.

S&F 110mm dia Junction single (Single or double T) equal or unequal complete all as specified and directed.

M&L PVC (SWR) floor trap 75 mm, plain with PVC grating including jointing with solvent cement etc.,complete all as specified and directed.

M&L for Cutting chases, pinning in. making good to facings where required for brick wall and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed.

S&F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall,fixed with self tapping screws complete all as specified and directed.

S&F rolled mild steel channel, angle as in purline, rafter & vertical type etc on roof cutting to dead length where required and welding to each other complete all as specified and as directed.

M&L PCC type C1 (1:2:4) using 20 mm graded aggregate as in bed block & coping complete all as specified and directed.

M&L posts and struts for fencing and other steel section including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or FE 310-0, complete all as specified and directed.

S&F GI 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75 mm spacing and stining and fixing to any type of standared rails straining bolts incl secuning or tying at crossing with and provison of GI mild steel wire staples or steel pins etc all as directed by the Engr-in-Charge(each line of wire to be measured)

Preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M & L for applying one coat of Cement base paint over old surface of walls including preparation of surfaces, complete all as specified and directed.

M & L for old surface Finishing walls with Acrylic Smooth exterior paint of required shade : New work (one coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm), complete all as specified and directed.

M&L for providing and fixing gypsum board panel laminated with texture vinyl coated paper tiles of size 595mmX595mmX12mm thick as in ceiling having snap grid 600mmX600mm incl GI wall angle of size 24mmX24mmX0.43mm thick along with perimeter of ceiling, fixed to walls/partition with the help of nylon sleeves at 450mm centre to centre, suspending intermediate tee section of size 24mmX38mmX0.35mm thick suspended from soffit of ceiling at upto 900mm centre to centre or adjustable as required at site 4mm dia GI wire hangers/tightened with ceiling with the help of nylon sleeve/rawl plugs complete all fittings complete all as specified and directedS&F Gypsum board 6 mm thick in ceiling fixed with screw of size 60cmX60cm placed in ceiling including aluminium anodised snap grid frame 605X605mm for false ceiling including hanging arrangement including complete all as specified and directed by Engr-in-charge.

S&F in repair powder coated aluminium frame for doors, windows, ventilators & Partation wall with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F powder coated aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed..

M&L for 4.8 mm thick sheet glass ordinary quality and glazing with rubber gasket in squares exc 0.5 sqm in each sheet glass frosted complet all as specified and as directed.

S&F powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

Supply and fixed hydraulic door closer of aluminium die cast body,designation No-3 universal type suitable for door shutter of 851 mm to 1000 mm weight between 61 Kg to 80 kg, etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixed Brass mortice lock 75 mm, 2 levers, vertical type, complete all as specified and directed.

Material and labour for applying bond coat of epoxy bonding agent & cement mortor in 1:1 ratio for bonding old and new concrete on damaged surfaces applying ready mix polymer modified mortar upto 60mm thickness (Chajjas fins, border,slab, beams etc) :- (i) Including application of rust remover on exposed reinforcement and subsequent application of anticorrosive coating. Also, pressure grouting with epoxy injection after application of polymer modified mortar. (ii) Use of electrical mixer to get the homogeneous dough on bond coat surfaces. (iii) To achieve required thickness repeat this step after 24 hrs as required. (iv) Keep the surfaces moist using water forg for 5 to 7 days etc complete all as specified and as directed. (v) Rate shall be inclusive of all necessary scaffolding for building height up to 24 meters complete all as directed by Engineer-in-Charge. Contd...117.01/-

Make of Chemicals : - Epoxy bonding agent, Rust remover, Anti corrosive coating, Polymer modified mortar, Epoxy grout shall be of Berger, Krishna, Dr Fixit, MC Bauchemie and M/s Cemistik, Sika or Equivalent as approved by GE. Notes : (i) Complete treatment to be executed by approved applicator (Applicator to be approved by GE). (ii) The Contractor and manufacture of polymer modified mortar shall give the warranty before commencement and also for the strengths achieved in the post completion of work. (iii) The chemicals to be used in the work shall be certified by the manufacturer with whom the MOU been entered into. (iv) Hard drawn steel wire fabric will be measured and paid seperately

S&F mild steel TMT bars as in reinforcement 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length,bent to shape required including cranking, bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified & directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, or laying of cable and getting out etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out, complete all as specified & directed.

M&L for PCC 1:4:8 type 'D2 using 40mm graded stone aggregate in foundation filling & mass concreate, complete all as specified & directed.

Returning filling in including spreading levelling watering and well ramming in layeras n.exc 25 cm in soft soil, complete all as specified & directed.

Removing excavated material n.exc 50M and deposting where directed at a level n.exc 1.5m above the starting point, complete all as specified & directed.

M&L Brick work in cement mortar 1:4 using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls, complete all as specified & directed.

M & L Hardcore of broken bricks of gauge n.exc 63mm, deposited, spread and leveled in layers n.exc 15 cm thick, watered and rammed to a true surface, complete all as specified & directed.

M & L Damp proof course,40mm thick in cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate using WPC (powder) including necessary form work, complete all as specified & directed. (WPC shall be measured separately).

Supply only integral water proofing compound (WPC),ISI marked, complete all as specified & directed.

M & L Formwork to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work (Horizontal or sloping), complete all as specified & directed.

M & L for formwork to sides and soffits of floor or roof beams, beams haunchings, girders, bressummers, lintels, cantilever, shelves including supports, overhangs, etc also splays between floors and beams etc rough finished surfaces of concrete all as specified and directed

Reinforced cement concrete (1:1.5:3), type A1(M20) using 20mm graded stone aggregate as in roof/floor slabs supported on walls, beams & columns landing, balconies, canopres, aech slabs and in shelves and the like, complete all as specified & directed. (form work and reinforcement measured separately).

Reinforced cement concrete (1:1.5:3),type A1(M20) using 20mm graded stone aggregate as in lintel up to 1.5 m span including necessary form work,complete all as specified & directed. (form work and reinforcement measured separately).

S&F mild steel TMT bars as in reinforcement 10mm dia and over cut to length,bent to shape required including cranking, bending spirally for columns, hooking ends and binding with and including mild steel eire (annealed) not less than 0.9 mm dia, complete all as specified & directed.

S&F aluminium anodised handles 125 mm long fixed to doors, complete all as specified & directed.

S & F aluminium anodised butt hinges, 100 mm long, fixed with galvanised mild steel hinge pin, complete all as specified & directed.

M & L cement concrete 1:3:6 type C2 with using 40 mm graded stone aggregate as in concrete bed to drain pipe 150 mm dia including packing under and haunching against the sides of pipe after they are laid and tested completed all as specified and directed

M & L 150 mm dia salt glazed stoneware drain pipes laid in trenches and jointed, complete all as specified & directed.

M & L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for & forming branch channel (1/2 round or ¾ section) in cement concrete 1:2:4 type B1 smooth finished and reforming branching as required for 150 mm dia pipes, complete all as specified & directed.

S & F Water storage tanks 500 liters capacity rotational moulded, triple layer polythene (cyindrical vertical with closed top) hoisting and fixed in position on roofs, complete all as specified & directed.

S & F Ball valve of brass, 20mm bore, high pressure with ploythene float and fly nut complete screwed for iron pipe of brass ferrule and fixed, complete all as specified & directed.

S & F single piece WC of size 365x655x765 with flushing cistern and connection pipe P or S trap (Closed pattern incl all necessary accessories like rag bolts, kit/gel gasket etc (including flushing cistern, pvc seat cover, jet and flush pipe complete all as specified and as directed. Make :- cera, Parryware, somani.

S & F Vitreous china (White) flat back urinal of size 465x355x265mm with grating, union for discharge pipe, spreader, 40mm dia PVC waste pipe upto floor trap, , flush pipe, union for discharge pipe, complete all as specified & directed.

S & F Pillar tap,15mm bore, cast copper alloy,with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts,screwed for iron pipe, complete all as specified & directed.

S & F Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed to walls with steel screws and wooden/rawl plugs, complete all as specified & directed.

S & F Stop valves of cast copper alloy, 15mm bore, screwed down, high pressure with crutch or butter fly handle, with long shank and cup (concealed type), complete all as specified & directed.

S & F Steel ventilators fixed type complete with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified & directed.

M & L for applying three coats of White wash on newly plastered surfaces of ceiling including preparation of surfaces, complete all as specified & directed.

M & L for precast cement concrete 1:2:4 type B-1 with using 20 mm graded stone aggregate as in manhole cover /Buffle wall and placing where directed including necessary formwork, complete all as specified & directed.

Taking down carefully copper /aluminium point wiring (light, fan , socket or power) complete, fittings such as switches, ceiling roses, pendants, regulators sockets light fitting etc removing materials to store for keetping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc, complete all as specified & directed.

Taking down carefully unserviceable main switches and distribution boards with fuses/ MCB's (single phase or three phase) of any capacity all as specified and directed.

Taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as directed and specified

M & L Point wiring complete with 1100 volts grade PVC insulated unsheathed FRLS cable of copper conductor, multi stranded of size 1.5 sqmm, single core, in and including rigid non-metallic PVC conealed conduit, with all accessories if require such as bends,reducers, spacers, saddles, junction boxes bakelite sheets, wooden rectangular boards / round blocks (for housing lamp holders and light fittings etc) and existing MS pressed steel / cast iron sunken boxes of suitable size for mounting switches / bell pushes / sockets, fan regulator etc covered with new 3 mm thick laminated bakelite sheet top cover including continuous earth wire of size 1.5 sqmm unsheated stranded copper conductor with green PVC FRLS insulation connected to common earth dolly complete all as specified and directed for the followings :- (a) One light/fan/Bell Point controlled by one single pole one way switch.

All as per item No. 150 here-in-before but One socket outlet on the same board controlled by one single pole one way switch, complete all as specified & directed.

All as per item No. 150 here-in-before but One 3 pin 5 amps socket outlet independent controlled by one single pole 5 Amp switch, complete all as specified & directed.

All as per Item No 152 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 Sq mm PVC FRLS insulated copper conductor and 2.5 Sqmm copper conductor for continuous earthing, complete all as specified & directed.

All as per item No. 153 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 4.0 Sqmm PVC FRLS insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 4.0 Sqmm green colours PVC FRLS insulated, unsheathed, stranded copper conductor cable, complete all as specified & directed.

Supply & Fixing Switch piano flush type single pole one way 5/6 Amp, complete all as specified & directed.

Supply & Fixing Switch piano flush type 15 amps, single pole one way duly ISI marked, complete all as specified & directed.

Supply & fixing Socket outlet 2 in one , 5/6 Amps flush type ISI marked, complete all as specified & directed.

Supply & Fixing Socket outlet, 2 in one 6 pin 5 and 15 Amps piano flush type ISI marked, complete all as specified & directed.

Supply & Fixing bell push flush type 5 Amps duly ISI marked, complete all as specified & directed.

Supply & Fixing ceiling rose, PVC/Polycarbonate, isolated three terminals, complete all as specified & directed.

Supply & Fixing Lamp holder PVC/Polycarbonate, isolated with back plate suitable for batten fittings including 10W LED Bulb, complete all as specified and directed.

Supply & Fixing bell ding dong type AC 230 Volt single pole, complete all as specified & directed.

S & F in repair stepped type electronic fan regulater compatable with BLDC fan flush type on the existing phenolic laminated sheet etc. as reqd complete all as specifed and directed

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm, complete all as specified & directed.

S&F LED tube light fitting 1 X 20 W decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 230V, complete with all accessories internally pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size, complete all as specified & directed.

Supply and fixing LED street light fitting toughened glass 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp incl suitable size MS/ GI bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, complete all as specified and directed.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series VTPN DBs (Vertical type)fitted with ABS frame and 415 volts 200 Amps rated enameled bus bar 4 way dust and vermin proof ssuitable for incorporation of MCCB/MCBs duly concealed in wall and making good to distrubed surface and colour matching, complete all as specified & directed.

S&F Factory made single phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 6 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 240V, 50Hz supply, partly immersed in wall and making good distrubbed surfaces with matching colour, complete all as specified & directed.

Supply & Fixing sheet metal enclouser double door factory made powder coated out of CRCA mild steel sheet 1.2 mm thick wih metallic painting white series pre-wired SPN DBs, 240 volts 200 Amps rated bus bar,Neutral link,Earth bar and Din rail, 12 way dust and vermin proof suitable for incorporation of MCBs duly concealed in wall and making good to distrubed surface and colour matching, complete all as specified & directed.

Supply & Fixing MCCB 63 Amps, 415 volts, 16 KA, 4 Pole, complete all as specified & directed.

Supply & Fixing MCB, Single pole 240 V,6 - 32 Amps 10 KA 'B Series, complete all as specified & directed.

S&F MCB SPN, 40A - 63Amps, 240 volts, "C" series, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning, complete all as specified & directed.

Supply & Fixing MCB, Single Pole and neutral 240 V, 32 Amps 10 KA 'B' series, complete all as specified & directed.

Sheet Metal Enclosures with Socket plug top and MCBs Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 20 Amp complete all as specified and directed.

M & L for sub main wiring with two single core PVC insulated FRLS cable with Copper conductor unsheathed cable of size 2 x 6 sqmm drawn through in and including PVC Concealed with 1 x 6 sqmm PVC FRLS insulated copper conductor single core for continuous earthing complete including PVC conduit 25 mm dia, complete all as specified & directed. ( Note : Two run of single core PVC insulated cable with Copper conductor unsheathed cable of size 6.0 Sqmm and one run of 6.0 Sqmm PVC insulated copper conductor single core,one run of PVC conduit shall be measured as single run)

Cutting holes making good the distributed surface, grouting nuts for fixing of Exhaust fans complete all as specified and directed.

Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6.0 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC ( 1:3:6 ) type C-2 using 40 mm graded stone aggregate. The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate, excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009)

Mild steel galvanised iron pipe light grade (ISI marked) 40mm bore for passing of earth lead laid in trenches fixed to walls laid under floors, roads including all fittings i.e MS clamps nuts & bolts etc, complete all as specified & directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with highefficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size, complete all as specified & directed.

S&F exhaust fan heavy duty copper winding with louvers complete of sweep size 300mm, 900 RPM, single phase, with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection, complete all as specified & directed.

S&F XLPE insulated, armoured,1100 volts grade, heavy duty cable of size 10 Sqmm nominal cross section, 4 core, flat or circular, PVC FRLS insulated aluminium conductor, served with inner sheathing of galvanized steel wire or tape and over-all PVC FRLS sheathed in service connections, laid in trenches, duct, through pipe, in floor, on pole including jointing and testing, complete all as specified & directed.

S&F Cover to underground cable with one layer of bricks using sub class ‘B’ bricks (old size) laid flat across the cable, complete all as specified & directed. (Excavation and earth work measured separately.

M&L for cutting of existing GI tubing 40mm dia for making new conncetion, inserting un equal Tee 40X40X25mm dia including excavation, returning filling complete and all as directed and specified.

Supply and laying GI tubing medium grade galvanised of size 25mm bore laid on floor/ ceiling including all fittings and short pieces complete all as directed by Engineer-in-Charge.

Supply and fix Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of 25mm bore, complete all as specified & directed.

Supreme Constructions (BID ID -3510731)

Marwaha Builders (BID ID -3510115)