CERTAIN REPAIR TO ROOFING, CEILING, JOINERY, FLOORING, PLASTERING, INTERNAL WATER SUPPLY, SANITARY AND PLUMBING ETC AT DIFFERENT LOCATION AT MARIANI UNDER GE JORHAT.

Amount

NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Dismantling plain/corrugated steel sheeting, any guage, thickness including eves gutter / rain water pipe complete & removal all as specified

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and as directed.

Material, labour and fixed of rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 410-W (Gde-E- 250) quality-A etc complete all as specified and as directed.

Material, labour and fixed of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and pitch length 75 mm c/c of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Material, labour and fixed of pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.

Material, labour and fixed of anodised aluminium snap grid frame work for false ceiling, size of grid 605 x 605 mm, including aluminium main/closs tee of size 35mm x 23mm x 1.4 mm ( minimum) aluminum BULBED TEES section and aluminium angle of 23mm X 23mm X1.5mm thick( minimum), sutiable type GI wire hanging arrangement with adjuster all as specified in clause no 10.38 in SSR part-I and including 6 mm thick high pressure steam cured non asbestos fibre cement designer board as per IS 14862 with applying of two coats of acrylic distemper over a coat of primer including taking dwon existing false ceiling system complete all as specified and directed.

Demolition of cement concrete of any description and in any position such as sunken floor etc removing rubbish to a distance n.exc 100m at low lying area complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the MOD premises complete all as specified and as directed.

Material and labour for 75 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in plinth protection, finished even and smooth without using extra cement complete all as specified and as directed.

Plain Cement Concrete M-15(Nominal Mix) using 12.5 mm graded stone aggregate as in making good window opening, lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping, kneelers, apex stones, bed plates, kerbs, water trough and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

Material and labour for Plain Cement Concrete M-7.5(Nominal Mix) using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.18 Sqm and not exceeding 0.36Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

All as per item no 13 but as in skirting/dado but over 10 mm thick rendering over CM 1:4

Material and labour for pre-polished chequered Cement Concrete tiles of 25 mm minimum thick, size of (square/ rectangular) area of each tile exceeding 0.09 Sqm but not exceeding 0.16 Sqm double layer machine pressed set ( as per IS 1237-2012), jointed and pointed in neat cement slurry in floors and cut & polished in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Material and labour for old Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Material and labour for brick work with bricks class designation 75, size as per old size brick, straight or curved on plan exceeding 6 m mean radius half brick thick walls built in Cement Mortar 1:4 complete all as specified and as directed.

Taking down cement plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removal outside of MOD land complete all as specified and as directed.

Rendering 15 mm in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment. Note:- Water proofing compound shall be measure and paid separately

Material and labour for rendering 5 mm in Cement Mortar 1:3 on fair faces of brick work or concrete ceiling surfaces finished fair complete all as specified and as directed.

Material and labour for Preparation of new wall surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.

Material and labour for Preparation of new ceiling surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.

Material and labour for preparation of new surfaces and and applying 2 coats of cement based paint over a coat of alkali based primer complete all as specified and directed.

Stripping out tarfelt from old roof surfaces and removing unserviceable materials from site of work in low laying in outside MOD area complete all as specified and as directed.

Material and labour forrendering 15 mm(Avg) thick in Cement Mortar 1:4 finished even and smooth witht using extra cement after preparation of old roof surface with brushing and applied neat cement slurry with 3.0 Kg of cement per Square Metre existing surface complete all as specified and as directed

Supplying and laying 3mm thick APP (Atactic Polypropylene Polymer) modified prefabricated five layer, weight not less than 3.6 kg/Sqm water proofing membrane, black finished reinforced with non woven polyester matt laying over a coat of bituminous primer @ 0.40 Ltr / Sqm and two coats of Bitumen based UV reflective paint with aluminium finish over APP membrane. The membrane shall be laid using butane torch and sealing all joints etc all as specified in Para 11.44.5 of SSR Part I complete all as specified and as directed.

Cutting holes in brick walls exceeding half brick but not exceeding one brick built in cement mortar for inserting hold fasts or GI pipe and making good dismantled portion in cement concrete 1:2:4 type B1 exceeding one brick.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. exceeding 1.50 Sqm but not exceeding 4.00 Sqm each complete all as specified and as directed.

Taking down chowkats/frames with shutters (without taking off shutters from the frame) etc. not exceeding 1.50 Sqm each complete all as specified and as directed.

Taking down shutters of any description n exc 1 sq. m each complete all as specified and directed.

Taking down shutters of any description exc 1 sq. m and n exc 2 sq. m each complete all as specified and directed.

Material and labour for mild steel work as in bands, straps, supports or stays for RWP, ventilating pipes, clamps, hold fasts, wall ties conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply and fixing of 2nd class HW Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

Material and labour for 30 mm thick, second class hard wood, factory made glazed and skeleton shutters, open rebated and prepared to receive gauze, etc. with plain chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Material and labour for 35 mm thick, second class hard wood, factory made glazed and skeleton shutters, open rebated and prepared to receive gauze, etc. with plain chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Supply and fixing of 35 mm thick flush shutters, solid core construction, with block board core and comercial plywood face panels with one face is covered with decorative face veneer with lipping/frame to match all complete all as specified and as directed.

Material and labour for Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with Mild Steel square tube, suppling & fixing in opening as per drawing complete all as specified and directed.

Material and labour for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawingcomplete all as specified and directed.

Material and labour for 19/20 mm thick, block boards for cupboard shutter, grade 1 quality, exterior grade, commercial typ with decorative face veneer on both face fixed with screws to timber frame work, fixed with screws to timber frame work including taking dwon exsiting one complete all as specified and directed.

Supply and fixing of steel ventilator with top hung shutters including hinges with steel handle and steel peg stay complete without gauged bars, dovetailed or welded complete all as specified and as directed

Supply and fixing of steel windows with side hung shutters including hinges projecting type with steel handle and steel peg stay complete with gauged bars, dovetailed or welded complete all as specified and as directed

Supply and fixing of steel windows with side hung shutters including hinges box type with steel handle and steel peg stay complete without gauged bars, dovetailed or welded complete all as specified and as directed

Supply and fixing of Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Supply and fixing of aluminium sliding window with powder coating (minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed sliding shutter and one leaf gauged (fly proofing) sliding shutter. (ii) Opening of windows exceeding 0.90 Sqm but not exceeding 1.50 Sqm (iii) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (iv) All vertical/ horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, etc. (vi) Rest all as specified in drawing no CESZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5 & 5R/5. Note Nos :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window. (ii) Only Glass & wire mesh shall be measure and paid separately under relevant items of BOQ .

Material and labour for power coated anodised aluminium door shutters made of aluminium section as per TD drawing(not less than 2.00mm thick) including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, floor hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed.

Supply and fixing of aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum thickness of powder coating 50 micron) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge.

Supply and fixing of sheet glass 6 mm thick ordinary quality fixed to aluminum door in squares in each pane of required size complete all as specified and as directed.

Supply and fixing of sheet glass 4 mm thick ordinary quality fixed to aluminum window in squares in each pane of required size complete all as specified and as directed.

Supply and fixing in repairs of sheet glass 4 mm thick ordinary quality fixed to aluminum door & window in squares in each pane of required size complete all as specified and as directed.

Supply and fixing in repairs sheet glass (frosted on one side) 4 mm thick ordinary quality with oil putty in square not exceeding 0.5 Sqm in each pane.

Supply and fixing of Butt hinges Stainless steel 100 mm size complete all as specified and directed.

Supply and fixing of Butt hinges Stainless steel 75 mm size complete all as specified and directed.

Supply and fixing of Butt hinges Stainless steel 50mm size complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 100 mm complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 150 mm complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 200 mm complete all as specified and directed.

Supply and fixing of Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long .complete all as specified and as directed.

Supply and fixing of Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections 150 mm long .complete all as specified and as directed.

Supply and fixing in repairs Stainless Steel drapery road (1 mm thick stainless steel section outer dia 25 mm with bracket, ring & fancy side holders complete all as directed by Engr-in-Charge

Supply and fixing in repairs Double action floor spring hydraulically regulated made up of mini-mum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

Supply and fixing of 300mm ordinary rat tail rod pattern springs including roller and roller plate complete made out of brass complete all as specified and as directed

Supply and fixing of brass mortice lock vertical type, 4 lever, size 100 mm complete all as specified and directed.

Supply and fixing of Continuous (piano) hinges 40 mm size, stainless steel bright finished or electro galvanized complete all as specified and directed.

Supply and fixing of Stainless steel wire cloth, 0.43 mm nominal dia of wire and avergae width of aperture 1.00 mm and fixed with stainless steel wire staples complete all as specified and directed.

Supply and fixing in repairs Stainless steel wire cloth, 0.43 mm nominal dia of wire and avergae width of aperture 1.00 mm and fixed with stainless steel wire staples complete all as specified and directed.

Material and labour for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed..

Material and labour for Painting 2 coats of synthetic enamel paint on wooden surfaces of any description over 10 cm in width or girth including preparation new surface and one coat of pink primer complete all as specified and as directed.

Material and labour for preparation of old wood surface and applying one coats of synthetic enamel paint on steel surfaces of any description over 10 cm in girth or width complete all as specified and directed.

Material and labour for Preparation of old steel surface and applying one coats of synthetic enamel paint on steel surfaces of any description over 10 cm in girth or width complete all as specified and directed.

Supply and fixing of 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and including taking up old GI pipe complete all as specified and as directed.

Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors and including taking up old GI pipe complete all as specified and as directed. Note for item no 72_&73_:- All fitting & fixture such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector, holding clamp shall be provide as per site requirements as directed by Engg-In -Charge and same shall deem to be included in quoted rate.

Supply and fixing in repair of bib cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS -08 of Prayag or equivalent model of make list as given in PS as approved by Engg-in-Charge.

Supply and fixing in repair of chromium plated pillar cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS 02 of Prayag or equivalent model of make list as given in PS as approved by Engg-in-Charge.

Supply and fixing in repair of stop cock , concealed type cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS -18 of Prayag or equivalent model of make list as given in PS as approved by Engg-in-Charge.

Supply and fixing of vitreous china wash basin white flat back, size 550 x 400 mm including CP waste coupling,with GI pipe brackets & , rag bolt in cement concrete/brick wall and including taking down existing HWB and making good wall surface complete all as specified and as directed. Make: Cat no 10100 wash basin of Hindware or equivalent model of make list as given in PS as approved by Engg-in-Charge.

Supply and fixing as in repair of PVC low level flusing cistern 10 litres capacity white with ball valve & brackets with flush pipe complete all as specified and as directed. Make: Sleek Fresh ISI of Hindware or equivalent model of make list as given in PS as approved by Engg-in-Charge.

Supply and fixing as in repair of PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

Supply and fixing as in repair of PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

Supply and fixing in repairof Towel Rail 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed. Make :- Cat no BA-40 of Prayag or equivalent model of make list as given in PS as approved by Engg-in-Charge.

Supply and fixing in repair of 125 mm dia of shower rose with 225 mm long arms, cast copper alloy chromium plated , swivel joints and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no BS-76 of PRAYAG or equivalent model of make list as given in PS as approved by Engg-in-Charge.

Supplying, hoisted and fixed in position of rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 500 litres capacity with ISI marked and all as specified in IS 12701 and including taking down existing water tank complete all as specified and directed .

Supply and fixing of PVC ball valve for 20 mm dia GI pipe all complete complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )juction equal or unequal for 110 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of in repair uPVC (SWR) floor trap 75 mm, plain with CP grating including joining and solvent cement complete all as specified and directed.

Material and labour for Soap dish chrome plated complete all as specified and as directe

Supply and fixing in repair of stainless steeel of 304 grade of kitchen sink with drain board of overall size 915mmx460mm and bowl size 410mm x330mmx160mm depth or equivalent made of 1mm thick stainless steel sheet with 32mm bore CP waste coupling including ball and chain 300mm long with bass cap rubber plug, 32mm bore PVC waste pipe (heavy duty) 90cm long, and bedded in cement mortar and fixed in CP cantilever brackets. Make: Cat No. 1239D of PRAYAG or equivalent make as per PS

Supply and fixing of Vitreous china wash down water closet (pedestal pattern) with concealed S-trap or P-Trap, white, 390 mm high, seat cover including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc and including taking down existing one complete all as specified and as directed Mak:-SLICK of HINWARE or equivalent model of make list as given in PS as approved by Engg-in-Charge.

Supply and fixing of PVC seat cover with CP hingh including taking down existing one complete all as specified and as directed

Supply and fixing in repairs Vitreous China half stall urinals, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, magnum urinal spreader, pointing around urinal back in cement; flush pipe, grating and Union for discharge pipe and including taking down existing one complete all as specified and as directed

Supply and fixing of Vitreous china squatting pan, 'Orissa' pattern, size 580x440 mm white with including CI ‘P’ or ‘S’ trap & integral foot rests fixed in cement concrete and including taking down existing one complete all as specified and as directed

Supply and fixing in repairs 15 mm dia brass CP centre hole basin mixer for mixing hot & cold water screwed down for iron pipe and fixed as in repairs. Make Cat No Cat No. 7650 of Paryag or equivalent model of make list as given in PS

Supply and fixing as in repair of health faucet of ABS body with wall hook and including one metre long stainless steel braided rubber hose pipe fixed on 15 nn dia angle cock all complete complete all as specified and directed Make:- Cat No. BEA-41 Prayag equivalent model of make list as given in Approved Make list .

Supply and fixing in repair of chromium plated brass glass shelf fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified. Make :- Cat no BEA-47 of Prayag or equivalent model of make list as given in PS as approved by Engg-in-Charge.

Supply and fixing in repair of Bib tap standard of PTMT any colour high pressure screwed for 15 mm bore dia iron pipe and fixed .(Minimum weight 15mm-90gms) complete all as specified.

Supply and fixing in repair of piller tap standard of PTMT any colour high pressure screwed for 15 mm bore dia iron pipe and fixed .(Minimum weight 15mm-120gms) complete all as specified.

Supply and fixing in repair of stop valve standard of PTMT any colour high pressure screwed for 15 mm bore dia iron pipe and fixed .(Minimum weight 15mm-90gms) complete all as specified.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

M/S Praduman Kumar Sharma

M/S GOPAL ROY AND CO

MS J B CONSTRUCTION AND CO

SANDHUSONS

A M CHOUDHURY AND CO