SPECIAL REPAIRS TO BLDG. NO T-58 OF HQ COSA AT NAYA RAIPUR MIL STN UNDER AGE (I) NAYA RAIPUR

Amount

Demolition of cement concrete in ground floor and paving n.exc 15cm thick (below or above ground level) complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified.

M & L for Vitrified Ceramic tiles 10 mm thick Light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15 mm thick screed bed in cement and sand mortar 1:4, complete all as specified.

M&L non skid coloured ceramic tiles 7 to 8 mm thick(square/rectangular) area of each tiles exceeding 0.06 sqm but n.exc 0.11sqm in floor etc, over and including 15 mm thick screed bed in CM(1:6),set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface 300x200x5to6mm thick over and including 10 mm thick cement plaster in CM (1:4); set and jointed in neat cement slurry & pointed in white or coloured cement to match the surfaces complete all as specified.

M&L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone agg for plinth protection fair finished by filling expansion joint as directed by engr incharge.

Dismantling of wall and ceiling boards(fibre, pulp,insulation etc) or insulation board/slabs/blankets any thickness including cover fillets all as specified.

Supply & fixing 'E' board 605 x 605 x 4 mm thick white prelaminated set & embosed, reinforced, designer ceiling board tiles of approved texture fixed at all height laid on hot dipped galvanised iron imposed grid with 24 mm wide T-section exposed flanges which shall be powder coated, white,.the frame work shall comprises of main runner made from 0.33 mm thick galvanised steel sheet and of size 24 x 32 x 300 mm and spaced at 1200 mm center to center fixed to be structural soffits by approved hangers at 1200 mm rawl center, hangers of GI wire 4 mm dia to be fixed by approved rawl plug, level and fasteners and screws etc., the last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall, flush fitting of 120 mm long cross tee (with double stiching) to be interlocked between main runners at 600 mm center to center, size 1200 x 600 mm modules, cross tee longer than 600 mm to be supported independently on 600 x 600 mm moduler to be formed by fitting 600 mm long cross tee centrally between the 1200 mm cross tee. Tee, perimeter wall angle shall be of 0.45 mm thick GS sheet of size 19 x 19 mm and 300 mm long of white colour all as per manufacturer's instructions complete all as directed. Make:- i- Everest, ii- Armstrong, iii- Ramco Indusries

Taking down chowkats or frames exceeding 1.5 Sqm and not exceeding 4 Sqm with shutter (Without taking off shutters from the frame) & removing from site complete all as specified and directed.

Taking down chowkats or frames not exceeding 1.5 Sqm and with shutter (Without taking off shutters from the frame) & removing from site complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not other wise provided complete all as specified and as directed.

M & L for mild steel ramed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing of grade Fe 410-W (Gde E-250), etc complete all as specified

M&L Rolled mild steel in stairs (framed) including stringers, treades, landing,balusters, hand rails etc. in cluding cleats, brackets, etc.complete and connecting plates of grade Fe 410-W (Gde E-250), etc complete all as specified

S&F for wind ties for roof including securingbolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165.

S & F for 2nd Class Hardwood in Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered,put together with glue pinned at joints complete all as directed.

M&L for 35mm thick 2nd class HW rail and style plain framed, factory made paneled shutter (one panel) without interlocking rail and 12mm veneered particle board with commercial veneering on both faces the size of rail and style as per IS -1003 (Pt-I)kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for 30 mm thick, 2nd class hard wood , glazed & skeleton factory made shutters, open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.20(a) complete all as specified.

S&F Anodised aluminium frame for door section/ window section/ ventilator section for side hung type shutter /sliding type shutter/fixed type shutter in two or more tracks, including automatic locking handle , rollers and roller plate & fitting arrangement complete all as all as specified and directed by Engineer-in-charge.(Glass pane , hydraulic door closer , plush plate, floor hinges shall be measured and paid separately.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed by Eng-in-charge.

S&F galvanised steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified.

S&F for sheet glass 4mm thick, ordinary quality and glazing fixed with aluminium section in squares not exceeding 0.5Sqm in each pane complete all as specified.

S&F aluminium anodised barrel tower bolt 200 mm long complete all as specified.

S&F Aluminium alloy, anodised, sliding door bolt 300 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

S&F MS 100 mm size butt hinges medium wt. of cold rolled complete all as specified and directed

S&F Aluminium handles, cast type anodised 150mm size complete all as specified.

S & F Door closer hydraulically regulated of Aluminium (Extruded section) body designation No.2, universe type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 kg and fixed complete all as specified and directed.

S&F in repair 20 mm dia decorative type curtain rod with rings and brackets complete and all as specified and directed

S&F 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and direcetd.

S&F for Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified.

M & L for PCC 1:3:6 type C-1 using 20mm graded stone aggregate for hold fast blocks, including necessary form work for rough finished surfaces etc complete all as specified.

Dismantling plain or corrugated steel sheeting, any gauze, thickness, including Nainital or similar pattern roof coverings etc complete all as specified.

S & F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

S & F for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

S&F plain black mild steel sheeting 0.80mm thick in ridge, valley gutter & fascia,drip and straight flashing as directed by Eng-in-charge.

M&L for Preparation and repair to holes with section gel, joints of the sheets and after that laying and fixing of membrane of 1.5mm thick over the roof sheets and apply acylic base paint over the roof directed by Eng-in-charge ( Note: rate for scaffolding up to 7.5 mtr and other arrangments shall be included in the coated rate)

M&L for Providing, cement concrete in 1:2:4 Type B1, 20mm graded aggregate as in copping in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height,copings complete all as specified.

M&L one coat of synthetic enamel paint on Old surface steel surfaces of any description not otherwise described over 10cm width or girth including preparation of old surfaces complete and all as specified and directed

M & L for painting to new wood or wood based surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with pink primer (one coat) and finished with two coats of synthetic enamel paint complete all as specified.

S&F in repairs bib taps cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fancy type chromium plated of 15 mm bore dia of pipe complete all as specified and directed.

S&F in repairs Grating doom 125 mm dia with waste hole of PTMT Minimum weight 40 gms complete all as specified and directed.

S&F in repairs Stop valves cast copper alloy, screwed down, high pressure with crutch or butterfly handle chromium plated fancy type screwed both ends for iron pipe or for unions for 15 mm bore dia of pipe complete all as specified and directed.

S & F in repairs for Toilet paper holder of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F in repair 15mm bore Brass cp wall mixer for mixig hot & cold water screwed down , for iron pipe or for brass ferrule complete all as specified.

S&F in repairs PVC connection pipe 45 cm long with PTMT fixed to WHB, flushing cistern, sink complete all as specified.

S&F in repairs 75 mm dia outlet PVC (SWR) floor trap plain with steel grating including jointing with solvent cement complete all as specified.

S&F in repairs Vitreous China wash down water closet pan, semi-pedestal pattern (Anglo-Indian Type) including "P" or "S" trap (excluding flushing cistern and flush pipe) but including connection to trap, and to flushing pipe, anti-syphonage pipe etc. complete all as specified and as directed.

S&F in repairs for PVC valveless, syphonic action type, flushing cistern,low level, white, with inlet, ball valve, float and handle including bracketst and 38mm dia flush pipe of polyethylene for low level cistern complete all as specified and as directed.

S&F in repairs for Vitreous china wash basin, white flat back size 550x400mm including waste, chain & plug andporeclain stopper and bracket etc. Complete including cutting for and pinning in ends of brackets or errecting bracket and 32mm dia waste fitting brass chromium plated for sink etc;with long screwed shanks and fly nuts,flange end bedded in red lead cement including 32mm dia waiste pipe fitted complete all as specified and directed.

S&F in repair pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and flynuts, screwed for iron pipes and fixed for 15mm dia complete all specified and directed.

S&F in repairs Hand shower with 8 mm dia, 1.2 meter long flexible Tube & Wall hook, complete and all as specified and directed. Make- Jaquar or equivalent series in Hindware or parryware

S&F in repairs soap dish any type fixed to plugs with chromium plated brass screws complete all as specified and directed

M&L in repairs brass chromium plated tubular towel rail 20mm dia D type 600 mm long between flanges fixed Complete all as specified and directed.

M&L in repairs for 110mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints fixed on walls including PVC clamps fixed to wall properly including fixing of pipe with PCC (1:2:4) complete all as specified & directed.

M&L in repairs for 75mm bore, PVC (SWR) pipes, single socketed, in any length, with rubber ring joints,laid in trenches or in floors complete all as specified & directed.

M&L PVC (SWR) bend any radius 110mm dia complete all as specified.

M&L PVC (SWR) bend any radius 75mm dia complete all as specified.

M&L PVC(SWR) Tee any radius 110mm dia complete all as specified.

M&L PVC(SWR) Vent cowl 110mm dia complete all as specified.

S&F in repairs 20mm dia GI tubing medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed

S&F in repairs 25mm dia GI tubing medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed

S&F in repairs 25mm dia ball Brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipes or brass ferrule and fixed as in PVC Service tanks all as directed.

S&F in repairs 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to 20mm dia GI tube complete all as specified.

S&F in repairs 25mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed to 20mm dia GI tube complete all as specified.

S&F in repair pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and flynuts, screwed for iron pipes and fixed for 15mm dia complete all specified and directed.

Demolition of brick work with built in cement mortar, complete all as speicified and directed.

M & L brick work with sub class B old size bricks straight or curved on planexc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L 10mm thick rendering in CM 1:6 on fair faces of brick or concrete surfaces (internal walls) finished fair and even complete all as specified and as directed.

M&L 15mm thick rendering on fair faces of brick wall in CM 1:4 on fair face of brick work or concrete surface finished the surfce even & smooth without using extra cement complete all as specified and directed

M&L for two coat of oil bound distemper white/coloured or tinted on new decorated surfaces of walls over and including a coat of primer complete all as specified and directed by Engineer-in-Charge.

M&L for two coat of cement base paint on newly plastered surfaces of wall over and including a coat of primer complete all as specified and direced by Engineer in charge.

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for one coat of oil bound distemper white/coloured or tinted on old decorated surfaces of walls including complete removal of existing treatment complete all as specified and directed by Engineer-in-Charge.

Taking down carefully any type point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing ( Except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified and directed by Engr-in-charge.

Taking out DB/SPN/SP /TPN any type and making good the disturbed surfaces of wall to match with existing surfaces complete all as specified

Taking down submain wiring any type and making good the disturbed sufaces to match with the existing surfaces complete all as specified

M & L for Point wiring complete with ISI marked 1.5 Sqmm single core, FRLS Grade, PVC insulated unsheathed cable 1100 Volts grade with multistranded copper conductor drawn through in and including medium grade PVC conduit and accessories concealed in wall/roof/ceiling surface etc suitable for terminal boxes for fixing modular switches, sockets etc including suitable size modular plates concealed in walls and 1.5 Sqmm copper conductor as earth continuity to connect common earth dolly complete all as specified and directed :- For One light point controlled by one 5 Amps one way switch Make of Cable :- Havells / Polycab / Anchor and Make of PVC conduit & conduit accessories - PLAZA / FINOLEX/ KALINGA. Note : (i) Making good to match with the adjoining surface shall be included in the quoted rate. (ii) Rate shall be included for Cutting/chases of wall/floor/ceiling

Description all as per item No 77 here in before but for One ceiling fan /exhaust fan point controlled by one 5 Amps one way switch

Description all as per item No 77 here in before but for One three pins 5 Amps switch socket outlet point on independent board

Description all as per item No 77 here in before but for One three pins 5 Amps switch socket outlet point on same board with other switches

Description all as per item No 77 here in before but for 16 amps socket outlet with 4 Sqmm Copper incl 2.5 Sqmm PVC insulated copper conductor cable as earth continuity conductor and connecting to common earth dolly complete all as specified and directed.

S & F Modular switch 1 way 6 Amps, 1 module complete all as specified Make - Legrand/ Crab tree / Philips.

S & F Modular socket outlet 1 way 6 Amps 2/3 pins combined, 2 module complete all as specified Make - Legrand/ Crab tree / Philips

S & F Modular switch 1 way 16 Amps, 1 module complete, Make - Legrand/ Crab tree / Philips

S & F Modular socket outlet 1 way 6/16 Amps - 2/3 pins combined, 2 module complete all as specified Make - Legrand/ Crab tree / Philips

S & F modular cover plate any type of 2 module complete all as specified and directed by engg in charge.

S & F modular cover plate any type of 3 module complete all as specified and directed by engg in charge.

S & F modular cover plate any type of 4 module complete all as specified and directed by engg in charge.

S & F modular cover plate any type of 8 module complete all as specified and directed by engg in charge.

S&F Modular polycarbonate ceiling rose 63.50 mm dia , three terminals complete all as specified of Make - Legrand/ Crab tree / Philips

S & F modular fan regulator, 120 watts, ISI marked, 2 module, step type complete all as specified

Supply and fixing in repairs LED ceiling light fitting 35 watts, complete with all connected accessories, prewired with 3 core flexible wire of size 1.5 Sqmm upto light fitting complete connecting and testing complete all as specified and directed by Engr-in-charge. Make:- Wipro/Philips/Crompton

Supply and fix in repairs building security light of 35/36 watt IP 65 watt,LED die casting aluminium with LED street optic lenses ,efficacy of skyline plus is upto 120lm/w, with pea nut lenses LED type with bracket arrangement complete all as specified and directed by Engg in Chrge MAke - Wipro Cat No LR13-241-XXX-57-XX or equivalent series in Philips/Crompton

Supply and fixing in repair Wall mounting indoor decorativeLED T-8 batten with opel diffuser 1x 18 W LED tub light mounting over two nos of round wooden blocks complete with , tube and all accessories making electrical connections with twin core PVC flexible copper wire of size 0.50 sqmm upto 1.5 mtr length complete all as specified Make -Wipro/Philips/Crompton

S & F in repairs aesthitically designed linear mirror light worm white type 2 FEET LED 14 W ,230 V ,50Hz provided with a high output PMMA diffuser for glare free light and making connection complete all as specified and as directed. Make Wipro/Philips/Crompton

Supply & Fixing exhaust fan 300mm sweep of engineering body type 240 volts with Louvre shutter including accessories like nuts, bolts for fixing to walls, trusses, sheets & cutting holes if required complete all as specified and directed. Make : Orient/USHA/Crompton ( Old Fan to be submitted to MES store after disconnecting and dismantling)

S&F ceiling fan energy efficient , 1400 mm sweep size ,240 volts single phase including down rod, and all assesories making it fix in ceiling or fixing arrangement complete all as specified and directed by Engr in Charge ( Old Fan to be submitted to MES store after disconnecting and dismantling)

M&L for submain wiring comprising single core 2 Runs of 6 sqmm nominal cross sectional area multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade drawing in and including appropriate dia PVC conduits and conduit fittings complete including S&F ,1 X 4 sqmm nominal cross sectional area multimultistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified . Notes:- Two wires of 6 sqmm and one wire of 4 sqmm & PVC conduit shall be measured as one unit.

Supply and fix sheet metal enclosure earth plug socket for SP 20 amps , with single pole MCB 240 volts complete all as specified. (Make- Legrand / L&T / Havells)

S&F Sheet metal enclosure MCB distribution board including 200 Amps bus-bar single pole and neutral 240V, 12 Ways, double door type, including taking down of existing sheet metal enclosure complete all as specifide and directed. (Make- Legrand / L&T / Havells)

S & F MCB SPN 40 to 63 Amps, 240 Volts, minimum 10 KA, "C" series rupturing capacity and to be housed in DBs catered here in before complete all as specified and directed :-(Make- Legrand / L&T / Havells) (Note :- Proper and suitable size cablecopper lugs to be fixed with MCBs are included in unit rate of each MCB of any rating)

S & F MCB SP 5 t 32 Amps, 240 Volts, minimum 10 KA, "C" series rupturing capacity and to be housed in DBs catered here in before complete all as specified and directed :-(Make- Legrand / L&T / Havells) (Note :- Proper and suitable size cablecopper lugs to be fixed with MCBs are included in unit rate of each MCB of any rating)

S & F MCB TPN 25 to 63 Amps, 240 Volts, minimum 10 KA, "C" series rupturing capacity and to be housed in DBs catered here in before complete all as specified and directed :- Make- Legrand / L&T / Havells Note :- Proper and suitable size cablecopper lugs to be fixed with MCBs are included in unit rate of each MCB of any rating

S&F Sheet metal enclosure MCB distribution board including 200 Amps bus-bar single pole and neutral 415 V, 4 Ways, double door type,complete all as specifide and directed. Make- Legrand / L&T / Havells

Total contract sum shall be calculated after deduction of schedule of credit amount of Rs. 46531.00

rupesh kumar jha

M/s SKP CONSTRUCTION