C.o Ayurvedic Health Center Building at Tiyali in Tehsil Theog District Shimla HP SH C.o Building portion i.c W.S and S.I site development C.o septic tank and site development and P.F solar System etc

Amount

Excavation in foundation, trenches, etcetra in earth work in all kinds of classification, of soils such as pick work, jumper work blasting work saturated soils including chiseling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals, lift up to any height stacking excavated soil up to all leads and lifts clear from the edge of excavation and then returning the stacked soil in fifteen centimetre thick layer when required into plinths, sides of foundation etcetra consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth to the disposal point complete in all respect . including all leads and lifts as per direction of the Engineer-in-Charge

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.including all leads and lifts as per direction of the Engineer-in-Charge

Providing form work with steel plates 3.15mm (Three point one five millimetre) thick welded with angle iron in frame 30x30x5mm (Thirty into thirty into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etcetra with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in complete including all leads and lifts as per direction of the Engineer-in-Charge

in foundation, footings bases of columns etcetera and mass concrete complete in all respect.

Flat surface such as soffits of suspended floors, roofs, landings and the like upto any thickness complete in all respect floor etc upto 200 mm thickness

in columns, pillars, posts and struts square, rectangular, polygonal in plan complete in all respect .

in stair cases with slopping or stepped soffits, excluding landing but complete in all respect .

In beam, cantilever, girders and lintels, sides and soffits of beams beams haunching below supporting cantilevers girders bressumers and lintels of any depth in all height from floor complete in all respect.

in edges of slabs and breaks in floors and walls of any width complete in all respect .

Vertical surface such as wall ( any thickness ) Partition and the including attached pillaster, butteresses plinth and string course and the like :-

Providing and laying cement concrete 1:8:16 (1cement: 8sand:16graded stone aggregate 20mm. nominal size) and curing complete on slab and floor excluding the cost of form work. screed laid under flooring.including all leads and lifts as per direction of the Engineer-in-Charge

Providing and laying cement concrete 1:2:4 (1 cement:2 Sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in including all leads and lifts as per direction of the Engineer-in-Charge(a )Foundation and plinth

Providing and laying cement concrete 1:4:8 (one cement : four sand : eight graded stone aggregate 40mm nominal size) and curing complete exluding cost of form work. including all leads and lifts as per direction of the Engineer-in-Charge

Foundation & plinth

Providing and laying cement concrete 1:4:8 (1 cement : 4 sand : 8 Graded stone aggregate 25mm nominal size) and curing complete excluding cost of form work in foundation and plinth in breast and retaining walls etc.including all leads and lifts as per direction of the Engineer-in-Charge

Providing and laying cement concrete 1:6:12 (1 cement:6 sand : 12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of centring and shuttering in: including all leads and lifts as per direction of the Engineer-in-Charge Foundation and plinth.

Providing and laying damp proof course 38mm thick with cement concrete 1:2:4 (1 cement:2 sand:4 stone aggregate 12.5mm nominal size) and curing complete including all leads and lifts as per direction of the Engineer-in-Charge

Applying a coat of hot bitumen (mexphalt 80/100 or equivalent) using 1.70 kg. per square metre on damp proof course after cleaning the surface with a piece of cloth lightly soaked with kerosene oil. including all leads and lifts as per direction of the Engineer-in-Charge

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg. of cement per sq.metre of floor area before laying cementconcrete flooring including roughening, leaning of theconcrete surfaces complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and laying cementconcrete 1:3:6 (1 cement : 3 sand :6 graded stone aggregate 20 mmnominal size) and curing complete excluding cost of form work in: including all leads and lifts as per direction of the Engineer-in-Charge (a) Foundation and plinth

Providing in RCC work smooth finishing of the exposed surface with cement mortar 1:3 (1 cement : 3 sand) including all leads and lifts as per direction of the Engineer-in-Charge

Providing and laying Cement Concrete 1:1.5:3 (1 cement :1.5 Sand : 3 graded stone aggregate 20 mm nominal size ) and Curing complete excluding Cost of form work and reinforcement for reinforced Concrete work including all leads and lifts as per direction of the Engineer-in-Charge

in foundation footing, basis of columns and the like mass concrete upto floor all level including curing complete

in suspended floor, roofs, landing and shelves and their support balconies beams girders bressumers and cantilevers upto floor all level including curing complete .

in Columns, pillars posts and struts upto floor all level including curing complete.

In stair cases (except spiral stair cases) excluding landing but including preparing of top surface and finishing of nosing upto all floor level including curing complete .

Providing and laying mechanically mixed and vibrated reinforced cement concrete of mix design to have characterstic strength of M-20 grade including cost of form work but excluding the cost of reinforcement for reinforced concrete work in string courses, coping bed plates, anchor blocks, plain window cills and the like upto all floor level complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing Tor steel reinforcement for RCC work including bending binding and placing in position including cost of binding wire complete upto all floor level complete including all leads and lifts as per direction of the Engineer-in-Charge

Brick work using common burnt clay building bricks in cement mortar 1:6 (one cement : six sand) second class bricks.super-structure above plinth level upto floor two level complete including all leads and lifts as per direction of the Engineer-in-Charge

Above plinth and upto floor two level ( upto GF)

Half Brick masonry in 2nd class common burnt clay building bricks in cement mortar 1: 4 ( one cement : four sand ) complete including all leads and lifts as per direction of the Engineer-in-Charge

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1 cement :6 sand : 12 graded stone aggregate 20mm nominal size) at plinth level in Cement Mortar 1:6(1 cement:6sand) including all leads and lifts as per direction of the Engineer-in-Charge.

Boulder filling dry hand packed tightly under floor including all leads and lifts as per direction of the Engineer-in-Charge

Stone filling behind retaining walls including all leads and lifts as per direction of the Engineer-in-Charge

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position complete including all leads and lifts as per direction of the Engineer-in-Charge

2nd class deodar wood

P/F 12 mm thick prelaminated board both side bwp phenol bonded exterior/interior grade panalled shutters with frame of first class deodar wood for doors including bright finished/black enamelled iron butt hinges with necessary screws frame complete including all leads and lifts as per direction of the Engineer-in-Charge.(a)40 mm thick .

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws complete including all leads and lifts as per direction of the Engineer-in-Charge (a)2nd class deodar wood 40 mm thick

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws.complete including all leads and lifts as per direction of the Engineer-in-Charge(a)2nd class deodar wood. 40 mm thick

Providing 40x3 mm flat iron hold fast 40cm. Long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm nominal size) complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing bright finished hard drawn hooks and eyes completeincluding all leads and lifts as per direction of the Engineer-in-Charge (a)200 mm

Providing and fixing oxidized M.S. double acting spring hinges with necessary screws complete complete including all leads and lifts as per direction of the Engineer-in-Charge (a)150mm

Providing and fixing bright finished or/and black enamelled iron (Helical door spring 150mm ) complete including carriage of materials within all leads, lifts and other incidental charges.

Providing & fixing 1mm thick Lamination ISI Marked is No12823 with butt joints & fixing with nails & screws etc complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws complete including all leads and lifts as per direction of the Engineer-in-Charge. (a) Plain grill.

Providing & fixing 19 mm thick water proof commercial board in shelves / box for cup board with butt joints & fixing with nails & screws etc complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing & fixing 19 mm thick commercial board water proof shutter for up boards i/c fixing with nickel plated piano hinges with necessary screws etc completeincluding all leads and lifts as per direction of the Engineer-in-Charge.

Providing and fixing ply wood lining with butt jointing and nails (frame work and cove fillets to be measured and paid for separately) including all leads and lifts as per direction of the Engineer-in-Charge.(a) 6 mm thick.

Providing & fixing 1mm thick Lamination ISI Marked is No12823 with butt joints & fixing with nails & screws etc complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing & fixing 19mm x 6 mm thick hard wood edging all cut portion with nail & screws complete including all leads and lifts as per direction of the Engineer-in-Charge. (a) 1st class indian Teak wood

Providing and fixing anodized aluminium sliding door bolts anodized colour and shade with bolts and nuts screws etc complete including all leads and lifts as per direction of the Engineer-in-Charge (a)300x16mm ( Three hundred into sixteen millimetre )

250x16mm ( Two hundred fifty into sixteen millimetre)

Providing and fixing heavy duty aluminum tower bolts (Barrel type) anodized transparent or dyed to required shade and colour with screws etcetra as approved complete including all leads and lifts as per direction of the Engineer-in-Charge.(a)250x10mm (Two hundred fifty into ten millimeter)

100x10mm (One hundred into ten millimeter)

Providing and fixing aluminium handles anodized transparent or dyed to required colour of shade with necessary screws etcetera complete including all leads and lifts as per direction of the Engineer-in-Charge. (a)125mm ( one hundred twenty five millimetre)

100mm ( one hundred millimetre)

75 mm ( Seventy five millimetre )

Providing and fixing 100mm (one hundred millimetre) bright finished brass floor door stopper with rubber cushion screws etcetra to suit shutter thickness complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and fixing bright finished brass ball catcher including all leads and lifts as per direction of the Engineer-in-Charge.(a)10 mm dia

Prokviding and fixing 65x35mm. special quality bright finished brass cup board locks or wardrobe locks with six levers including necessary screws etc. complete. including all leads and lifts as per direction of the Engineer-in-Charge.(Indian make of approved quality).

25mm (twenty five millimeter) thick kota stone slab flooring 55 cm x 55 cm 20mm (twenty millimeter) (average) thick base of cement mortar 1:4 (one cement : four sand) laid over and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including all leads and lifts as per direction of the Engineer-in-Charge.charges.

Providing and fixing 2mm thick PVC antistatic flooring plain or coloured, carbed or mosaic/metalled finish laid with approved adhesive on sub-floor (damp proofing treatment to be paid for seprately) including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and laying Baroda Green Marble work (table rubbed and polished) in flooring 20mm (twenty millimetre) thick base in cement mortar 1:3 (one cement : three sand) including jointing with cement mortar 1:2 (one white cement : two marble dust) with an admixture of pigment to match the shade of the marble 20mm (Twenty millimetre) thick complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and laying Vetrified ceramic tiles of 5.5mm thick in flooring (300x300mm size) treads of steps of steps laid on a bed of 12mm thick cement mortar 1:3 (1Cement : 3Sand) finished with flush pointing in white cement complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and laying red sand stone slab flooring 40mm average thick on 20mm average thick base of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab i/c rubbing and granite polish finish complete. including all leads and lifts as per direction of the Engineer-in-Charge.

Kota stone slab 25 mm thick in risers of steps,skirting dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing including all leads and lifts as per direction of the Engineer-in-Charge.

40mm (forty millimeter) thick cement concrete flooring 1:2:4 (one cement : two sand : four graded/crushed stone aggregate 20mm (twenty millimeter) nominal size) laid in one layer finished with a floating coat of neat complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing & fixing Uni Stone cladding 12 mm thick as on face of arch masonry walls etc on 12 mm thick cement plaster 1:3 ( one cement : three sand )jointing with cement slurry including scaffloding etc complete including all leads and lifts as per direction of the Engineer-in-Charge.

White glazed tiles 6mm (six millimetre) thick in skirting riser of steps and dado 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) and jointed with cement slurry upto all floor level complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and laying heavy duty precast cement conrete inter locking paver blocks vibro compacted upto M- 50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete including all leads and lifts as per direction of the Engineer-in-Charge.. (Sub base concrete floor to be paid for(a) 40mm thick block

Making half round nosing to kota stone/granite stone/marble including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and laying red sand stone slab flooring 40mm average thick on 20mm average thick base of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab i/c rubbing and granite polish finish complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and fixing 0.60mm (zero point six zero millimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating to back coat of polyster 5 (five) microns over 5 (five) microns primer coating including fixing with screws prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre with prepainted limpet and rubber washers complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and fixing ridges or hips 60cm (sixty centimetre) overall with 0.60mm (zero point six zero millimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) microns primer coating plus back coat of polyster of 5 (five) microns over 5 (five) microns primer coating icluding fixing with screws prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre with prepainted GI limpet and bitumen washers complete with all accesoriees as required complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and fixing valley 60cm (sixty centimetre) overall with 0.60mm (zero point six zero millimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster 5 (five) microns over 5 (five) microns primer coating icluding fixing with screws prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre with prepainted GI limpet and bitumen washers complete with all accesoriees as required complete including all leads and lifts as per direction of the Engineer-in-Charge.

Prividing and fixing flushing 38cm (thirty eight centimetre) overall with 0.60mm (zero point six zero millimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 (five) mircorns primer coating plus back coat of polyster of 5 (five) microsn over 5 (five) microns primer coating including fixing with screws prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre & prepainted GI limpet & bitumen washers complete with all accessories as required complete in all respect.

Providing and fixing MS BP sheet 1.66mm to 2mm (one point six six millimetre to two millimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured & paid separately) including complete including carriage of materials within all leads, lifts and other incidental charges.

Steel work welded in built up sections trusses and framed work including cutting, hoisting, fixing and launching in position and applying a priming coat of red lead paint in trusses and trussed purlins in buildings complete including all leads and lifts as per direction of the Engineer-in-Charge.(a)In trusses and trussed purlins in building

in gratings framed guard bars , ladders , railing , brackets and similars works .

Providing and fixing M.S.round holding down or anchor bolts with nuts and washer plates complete including all leads and lifts as per direction of the Engineer-in-Charge.

Steel work rivetted in built up sections including cutting,hoisting, fixing,in position and applying a priming coat of red lead paint .In grating,Framed guards, bars,ledders railings,brackets & similar works including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and fixing moulded hand rail of M.S. hollow pipe 50mm dia welded in straight lenght over M.S. flat at top of vertical balusters including one coat of red oxide priming coat complete (M.S. flat & balusters of railings shall be mesaured & paid separetely.including all leads and lifts as per direction of the Engineer-in-Charge.

Painting two coats (Excluding priming coat) on steel work and steel based surface under coat with enamel and finishing coating with flat oil paint, brushing to give an even shade including cleaning of all dirt, dust and other foreign matter, sand papering including all leads and lifts as per direction of the Engineer-in-Charge. (a) With ready mixed paint other than white.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by throughly cleanin oil, grease, dirt and other foreign sand papering and knotting. Ready mixed paint brushing primer for enamel complete including all leads and lifts as per direction of the Engineer-in-Charge.

Painting two coats (Excluding priming coat) on new wood and wood bassed surfaces with ready mixed white paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matters sand papering and stoping complete including all leads and lifts as per direction of the Engineer-in-Charge.

Applying Birla White wall care putty over plaster surface after throughly brushing the suface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the suface including all leads and lifts as per direction of the Engineer-in-Charge.

Finishing walls with Spectrum textured exterior paint of required shade to give an even shade after throughly cleaning the surface to remove all dirt, dist and other foreign matter etcetra including all leads and lifts as per direction of the Engineer-in-Charge.

Painting two coats (excluding priming coat) on new concrete/masnory/plaster surfaced with ready mixed paint white paint brushing for use on all floors to give an even shade including cleaning the surface of all dirt, dist and other foreign matter and sand papering smooth including all leads and lifts as per direction of the Engineer-in-Charge.

Applying synthetic distmper on plaster surface after and including preparing the surface by thorughly cleaning oil,dirt, grease and other foreign matter and kind perparing as required including all leads and lifts as per direction of the Engineer-in-Charge.

6mm (six millimeter) thick cement plaster to ceiling with cement mortar 1:3 (one cement : three sand) including curing complete in all respect.including all leads and lifts as per direction of the Engineer-in-Charge.

15mm (Fifteen millimeter) cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto floor all level including arrises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (eighty millimeter) in girth and finished even and smooth in cement mortar 1:6 (one cement : six sand) including curing complete including all leads and lifts as per direction of the Engineer-in-Charge.

15mm (fifteen millimetre) cement plaster in single coat on the fair side of brick/concrete/stone walls for interior plastering upto floor all level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement : six sand) complete including all leads and lifts as per direction of the Engineer-in-Charge.

20 mm cement plaster in two coats, backing coat 15 mm amd finishing coat 5 mm thick on rough side of brick/stone masonry walls upto two floor level complete.including all leads and lifts as per direction of the Engineer-in-Charge .(a)Cement mortar 1:6 ( 1 Cement : 6 sand )

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including all leads and lifts as per direction of the Engineer-in-Charge

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size) including all leads and lifts as per direction of the Engineer-in-Charge

Providing and laying 23cm half glazed stoneware pipe in plinth protection to drain out the rain water etc including all leads and lifts as per direction of the Engineer-in-Charge.

Providing & fixing to wall ceiling and floor galvanised mild steel tubes ( heavy grade) tube fitting and clamps including making good the wall , ceiling floor complete including all leads and lifts as per direction of the Engineer-in-Charge.(a)15 mm nominal bore

Providing & laying in trenches galvanised mild steel tubes ( heavy grade) tube fitting ( earth work in trenches to be measured and paid separately complete. including all leads and lifts as per direction of the Engineer-in-Charge(a).20 mm nominal bore

Making connection to galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and treading the pipe complete. including all leads and lifts as per direction of the Engineer-in-Charge.

Constructing water collection chamber 300x300x650mm (three hundred into (three hundred into six hundred fifty millimetre) in side size for collection of water with cement concrete slab 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimeetre) nominal size) 75mm (seventy five millimetre) thick foundation concrete 1:5:10 (one cement : five sand : ten graded stone aggregate 40mm (forty millimetre) nominal size) finished with floating coat of neat cement and 100mm (one hundred millimetre) cast insitu plain concrete wall in 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre nominal size) including form work complete including all leads and lifts as per direction of the Engineer-in-Charge.wirh 100 mm thick walls of bricks masonry in Cement mortar 1:5 ( 1 cement : 5 sand )

Providing and fixing GI clamps for support vertical soil waste , sand cast (spun) iron pipes embedded in walls with anchor fastner etcetra including all leads and lifts as per direction of the Engineer-in-Charge.75 mm nominal diametre

100 mm nominal diametre

Providing and fixing Vitreous china wash down water closet (European type W.C.Pan wirh integral " P" or " S" trap including jointing the trap with soil pipe in cement mortar 1:1 ( one cement : one sand ) seat and cover to be measured and paid for separately ) including all leads and lifts as per direction of the Engineer-in-Charge(a) Angle indian universal closet

Providing and fixing G.I. inlet connection for flush pipe with W.C. pan iincluding all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing Solid Type white plastic sheet (Solid/Hollow type) and cover for washed on water closet with CP brass hinges and rubber buffers including all leads and lifts as per direction of the Engineer-in-Charge Solid Type (a) White plastic seat and cover

Providing and fixing flat back 550x 400mm (Five hundred fifty into four hundred millimeter) vitreous china wash basin with single hole for pillar tap with CI or MS brackets painted white including cutting holes and making good the same but excluding fittings complete in all respect cera or its equivalent . including all leads and lifts as per direction of the Engineer-in-Charge Flat back (a)550mm x 400 mm

Providing and fixing vitreous china pedastal for wash basin complete recessed at the back for the reception of pipes and fittings. including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing 32mm (thirty two millimetre) diametre CP brass waste heavy duty for wash basin or sink complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing & fixing M.I union for wash basin or sink . 32 mm complete. including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and fixing 32mm (thirty two millimetre) diametre lead waste pipe for wash basin or sink in including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing 600x450mm (six hundred into four hundred fifty millimetre) bavelled edge mirror of superior glass mounted on 6mm (six millimetre) thick AC sheet or ply wood sheet and fixed to wooden plugs with CP brass screws and washers complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and fixing 600 x 20mm (six hundred into twenty millimetre) CP brass towel rail complete with CP Brass brackets fixed to wooden plugs with CP brass including carriage of materials within all leads and lifts complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing 600x120mm (six hundred into one hundred twenty millimetre) glass self with CP brass brackets and guard rail complete fixed to wooden plugs with CP brass screws complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing choromium plated brass soap dish with CP brass brackets fixed to wooden cleats with CP brass screws complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing and fixing polythelene aluminium polythene (PE-AL-PE) composite pressure pipe U.V. stablized with carbon conforming to IS: 15450-2004 for water supply including clamps at one metre spacing, cutting, fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipes exposed on wall including carriage of materials within all leads, lifts and other incidental charges.

1216 (one thousand two hundred sixteen) (16mm (sixteen millimetre) O.D) pipe

Providing and fixing composite and seal compression fittings as per IS 15450-2004 for cold water supply for example tees, elbows, reducers, connectors, couplers and clamps with jointing, testing and fixing complete including cuting and making good the wall etc including all leads and lifts as per direction of the Engineer-in-Charge

Equal Tee

1216x15mm (one thousand two hundred sixteen into fifteen millimetre) thread

Female Elbows

1216x15mm (one thousand two hundred sixteen into fifteen millimetre) thread

Male Thread Connector

1216x15mm (one thousand two hundred sixteen into fifteen millimetre) thread

1620x20mm (one thousand six hundred twenty into twenty millimetre) thread

Female Thread Connector

1620x20mm (one thousand six hundred twenty into twenty millimetre) thread

Couplers

1216 (one thousand two hundred sixteen)

Providing and fixing 15mm (fifteen millimetre) diametre C.P.brass bib tap heavy duty with capstan head complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing 15mm (fifteen millimetre) diametre C.P.brass pillar tap with capstan head including carriage of materials within all leads and lifts complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing C.P.brass stop cock complete including all leads and lifts as per direction of the Engineer-in-Charge

15 mm (fifteen millimeter) diametre

Providing and fixing PVC connection pipe with brass unions 45cm (forty five centimeter) long 15mm (fifteen millimeter) nominal bore complete including all leads and lifts as per direction of the Engineer-in-Charge

300/450 mm length

15mm (fifteen millimeter) nominal bore

Providing and fixing brass full way valve with wheel with complete. including all leads and lifts as per direction of the Engineer-in-Charge (a)15 mm nominal bore

20 mm nominal bore

Providing & fixing PVC water storage tank of ISI : 12701 marked G.I inlet and out let connection , 15 mm normal bore ball valve and mosquito proof PVC cover with locking arrangement including hositing upto all heights above ground level 500 litres net capacity tank .including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing PVC water storage tank ISI : 12701 marked , G.I inlet and outlet connection , 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting uo to all heights above ground level Complete including all leads and lifts as per direction of the Engineer-in-Charge

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive , cost of cutting and making good the wall and floors etc. complete including all leads and lifts as per direction of the Engineer-in-Charge(a)110mm x 90 mm

Providing and fixing high pressure PVC spigot and socket , waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including all leads and lifts as per direction of the Engineer-in-Charge.(a)110 mm dia

75 mm dia

Providing and fixing PVC single equal branch with ovel access door ,ISI marked insertion rubber washer 3 mm thich bolts & nuts complete including fixing with approved adhesive etc. Completeincluding all leads and lifts as per direction of the Engineer-in-Charge(a).110 mm dia

75 mm dia

Providing and fixing PVC door bend branch with ovel access door ,ISI marked insertion rubber washer 3 mm thich bolts & nuts complete including fixing with approved adhesive etc. Complete.including all leads and lifts as per direction of the Engineer-in-Charge.(a).110 mm dia

75 mm dia

Providing and fixing PVC Collars ISI marked including fixing with approved adhesive etc. Complete..including all leads and lifts as per direction of the Engineer-in-Charge. (a)110 mm dia

75 mm dia

Providing and fixing PVC Plain bend ISI marked including fixing with approved adhesive etc. Complete.including all leads and lifts as per direction of the Engineer-in-Charge. (a)110 mm dia

75 mm dia

Providing and fixing PVC 'P' or 'S' trap for water closet ( Squatting pan ) ISI marked including jointing the trap with the pan snd PVC pipe with approved adhesive etc. Complete including all leads and lifts as per direction of the Engineer-in-Charge. (a)110 mm dia

Providing and fixing stainless steel Kitchen sink of approved standard ISI make with drain board and C.P waste with C.I or M.S brackets painted white including cutting hole s and making good the same complete . including all leads and lifts as per direction of the Engineer-in-Charge. (a)610 x 460 mm with bowl depth 200 mm

Providing & fixing white high density polythene 10 litres capacity European standard control low level flushing cistern with pair of brackets with fitting such as lead valve , syphon , 15 mm nominal size PVC ball valve with float with npush button , coupling for connection with inlet , outlet with complete including all leads and lifts as per direction of the Engineer-in-Charge.

Providing & laying ( to level or slopes ) and jointing with stiff mixture of Cement mortar in the proporation of 1:1( 1 cement ; 1 sand 0salt glazed stone ware pipes grade 'A' including testing of pipes and joints complete. including all leads and lifts as per direction of the Engineer-in-Charge.

Providing & fixing Cast iron mainhole cover 500 mm internal dia weight of cover and frame not less than 58 kg . including all leads and lifts as per direction of the Engineer-in-Charge.

Providing & fixing M.S Cover 300 mm x 300 mm including all leads and lifts as per direction of the Engineer-in-Charge.

Supply and stacking broken stone / brick bats etc . including all leads and lifts as per direction of the Engineer-in-Charge.

Providing & fixing brass full way valve with wheel including all leads and lifts as per direction of the Engineer-in-Charge..15 mm nominal bore

Providing & fixing BOSCH make solar water heating systems , flat plate , collector , glass enamel tank , 1C ( Non - Heating exchanger type ) Tank , Full plate Absorber collector with Advanced Toughened Solar Glass ( 02 No ) including all leads and lifts as per direction of the Engineer-in-Charge.

RAHUL BHARDWAJ

Dinesh Chandel

Sunil Hetta

Dinesh Kumar

Naresh Kumar